Search Documents

By P. Van Marcke, X. Sillen, G. J. Chen, I. Troullinos, A. Dizier, J. Leysens, X. L. Li, J. Verstricht

"In Belgium, Boom Clay is considered as one of the potential host formations for the disposal of the High Level radioactive Waste (HLW). The URL HADES at 223 m depth at Mol site was constructed in order to study the feasibility of HLW disposal in Boom Clay. Since 1995, the URL R&D programme has focused on large scale demonstration tests like the PRACLAY experiment.The PRACLAY in-situ experiments include a set of three tests: The gallery and crossing test, PRACLAY Heater test and PRACLAY seal test. The main aim of the Heater test is to study at a large scale the thermal impact of a HLW repository on the host rock. The test is housed in the PRACLAY gallery. A hydraulic seal, made of compacted swelling and low permeable bentonite annular ring was installed at the intersection between the heated and the non-heated part of the gallery. The primary objective of the seal is to provide undrained hydraulic boundary conditions for the Heater Test.The PRACLAY gallery was constructed in 2007 and the hydraulic seal was installed in 2010. The bentonite is hydrated by natural and artificial process. The swelling, total pressure and pore pressure of the bentonite are continuously measured and analysed by numerical simulations to get a better understanding of this hydration processes. The performance of the seal is tested systematically by means of gas injection breakthrough tests and permeability tests at interface bentonite / Boom Clay and in the Boom Clay around the seal.The PRACLAY Heater will be turned on at the end of Oct. 2014, since a sufficient seal swelling has been attained to fulfill its role for the PRACLAY Heater test. This paper will focus on the PRACLAY Seal test: How we understand the process behind the hydration of the bentonite and how we test the performance of the bentonite seal."

Jan 1, 2015

By J E. Gordon

For many years, it has been known that certain loud noises may, with prolonged exposure, temporarily or permanently damage a person's hearing ability. Pneumatic rock drills, al-though among the offenders, have, until recently, remained unaltered and unrestricted as to noise output. Now, there are drills available with higher rates of penetration and yet with noise levels reduced to those of previous models or less. Use of such drills, when proved to be superior in noise attenuation and of acceptable performance, should be encouraged in order to reduce future hearing losses to a minimum. People Have the Right to Hear P ERHAPS the earliest recognized indication of hearing loss due to industrial noise was the deaf-ness developed by the workmen in boiler factories. Here, the vibration set up in the shells by the riveting hammers gradually deteriorated the workmen's hearing, especially those whose job it was to hold the dollies inside the drum, where the sound is greatly intensified by reflection

Jan 1, 1963

By R. H. McMillan

A classification of important uranium deposits which utilizes both genetic and descriptive criteria is presented. The dual aspect is useful because, while the non-genetic nomenclature for the different deposit types is amenable to various interpretations, the critical characteristics of each deposit type can be analyzed to clarify various genetic points. Although the classification is intended primarily for Canadian uranium deposits, most of the important deposit types known elsewhere can be accommodated.

Jan 1, 1978

By Q. B. Li, B. Gonçalves da Silva, J. T. Germaine, H. H. Einstein, Z. Moradian

"Shale gas and oil production has grown rapidly in recent years, and consequently there are increasing demands to understand the mechanical and microseismic properties of shale. Acoustic emission (AE) monitoring provides useful information on the fracture mechanisms of shale rocks, and provides a basis for interpreting field seismic observations. While there have been attempts for microseismic monitoring of conventional hydrocarbon reservoirs, shale presents a large number of issues that require further investigation. For this purpose, experiments were conducted to understand the characteristics of the AE waveforms propagated through Opalinus shale rock in the time and frequency domains. Frequency range, arrival time, first arrival amplitude and other parameters such as counts, duration and energy of the waves generated from artificial and natural sources in the shale specimens were detected and compared with AE characteristics of granite, a brittle rock that has been extensively investigated. The experimental tests showed that there are some important factors that influence the analyses and interpretations of seismic surveys and microseismic monitoring of shale compared to granite. One of these factors is the anisotropic behavior of shale that causes the wave to propagate with different velocities in different directions. Also bedding planes and micro-discontinuities in the shale cause attenuation of the waves. Thus the AE waveforms that arrive at the sensor are a distorted and attenuated versions of the source waveform.INTRODUCTIONMonitoring microseismic activity from hydraulic fracturing of shale provides vital information for mapping injection paths and fluid migration in order to check the effectiveness of the hydraulic fracture stimulation. Analysis of microseismic source locations can be used to identify fracture networks induced or mobilized during the hydraulic fracturing operation (Rotherd and Shapiro, 2003). On the other hand, by monitoring and assessing detected signals from hydraulic fracturing one can evaluate the induced seismic impact of the stimulation operation.While there have been attempts to monitor microseismic events in conventional hydrocarbon reservoirs, shale presents a large number of issues that require further investigation. For this purpose, experiments were conducted on Opalinus shale to understand its acoustic emission (AE) characteristics in the time and frequency domains."

Jan 1, 2015

By C. E. Lancelle, J. T. Volk, H. F. Wang, D. Fratta

"The Main Injector Neutrino Oscillation Search (MINOS) Near Detector Hall at Fermilab and the Lafarge – Conco Mine are located approximately 100 meters underground in the Galena-Platteville dolomite just below its contact with the overlying Maquoketa shale in Northeastern Illinois, USA. A new cavern was excavated adjacent to the MINOS Near Detector Hall at Fermilab to house the near detector for the Off-axis Neutrino Appearance Experiment (NOvA) program. During this excavation approximately 1150 cubic meters of shale rock were removed. Tiltmeter arrays consisting of a series of hydrostatic leveling sensors (HLS), which are spaced regularly over a total distance of 50-to-100 meters, were used to monitor subsurface deformations. The tiltmeter response in the MINOS Near Detector Hall due to the NOvA cavern excavation is approximately thirteen times the estimated response based on using laboratorydetermined properties. The discrepancy between modeled and measured tilt is likely due to differences in Young’s Modulus in the rock mass versus in a small laboratory sample. Amplitudes of measured solid earth tides differ from the amplitudes of theoretical solid earth tides by up to 40 percent for both arrays. This is likely due to a local heterogeneity or discontinuity.INTRODUCTIONLong baseline tiltmeters have been used to record small earth movements since the early 1900s. One of the first studies using long baseline tiltmeters to measure earth tides was published by Michelson (1914). He used a leveled 152-meter long, 0.15-meter diameter tube half-filled with water connecting two concrete-lined pits. The pipe was trenched 1.75 meters underground in Williams Bay, Wisconsin in a sandy-clay soil. Initially only an east-west line was used, though a north-south line was added after it was seen that viable results were obtained. Measurements were made by hand either hourly or once every two hours depending on the time of day. When compared to 0.7 times the calculated earth tides, the tiltmeter signal matched almost exactly. This excellent result began the use of long baseline tiltmeters to measure small earth movements."

Jan 1, 2015

By Robert D. Brown, Robert B. Parsons

"The mining industry may have survived the October 28 federal budget relatively unscathed, but the same certainly cannot be said of the petroleum sector-and many mining men are left wondering if their industry will be the next one to be singled out for special attention, as federal and provincial governments seek additional revenues and pursue nationalistic or provincial policies.Higher taxes, higher prices, a potpourri of ""incentives"", and a -""Canadianization"" policy mark the principal features of the new National Energy Program released by the government along with Finance Minister MacEachen's budget address.This month, Tax Notes examines the federal budget. with appropriate emphasis on the National Energy Program and its possible future implications forthe Canadian resource industries.IntroductionMost of the Canadian mining industry (tar sands miners excepted) heaved a sigh of relief on the evening of October 28, 1980, as Finance Minister MacEachen confounded the prophets in his budget address by not raising personal or corporation taxes and by making only relatively modest changes in the general tax system. Instead, he concentrated on a sweeping new energy policy. Unfortunately for that important sector of Canada's mining industry which is involved in mining the country's vast tar sands reserves, either now or in the future, the National Energy Program that was introduced along with the budget 'has serious implications."

Jan 1, 1981

By H. A. Pearse

Introduction This paper may be regarded as another instalment of the story of the Britannia milling operation. From time to time in the past, articles (1) have been prepared by various members of the staff, giving details of crushing, grinding, and flotation treatment for the normal Britannia ore. It is not, therefore, the purpose of the present paper further to discuss what may be termed the standard milling operation, but rather to describe a flotation practice which has been evolved directly as a result of the general depression. The normal Britannia ore mixture contains chalcopyrite and pyrite as the main sulphide minerals, together with minor gold and silver values. The standard milling practice, evolved during several years of experimentation, provided for bulk flotation of the two sulphides after primary grinding to only approximately 35-mesh, followed by regrinding of the bulk concentrate, with subsequent separation of the chalcopyrite and pyrite to make a marketable concentrate of each mineral. However, in the face of a constantly increasing surplus of copper on the world markets and a steadily falling price during 1930 and 1931, it was obviously undesirable to continue producing large quantities of this metal at a loss. On the other hand, Company officials were very reluctant to add to unemployment by closing down entirely, provided operations could be continued without excessive losses. Fortunately, the existence was known of a fair sized body of ore, quite low in copper and relatively high in zinc content, with also a very considerably higher gold value than that prevailing in other sections of the mine.

Jan 1, 1934

By Alessandro Navarra, Amir Arash Rafiei, Kristian Waters

Mathematical programming (MP) is fundamental to systems engineering and operations management, but has not been widely adopted by mineral processors. The current paper presents an interdisciplinary approach, using MP to incorporate basic notions of mass balancing into an optimization framework. The optimization is typically related to economic profitability. Two- and three-product formulas are extended to give formal descriptions of alternate modes of operation, and a global representation of the concentrator. At this global level, the framework may assist plant managers to make tactical decisions based on incoming feed data. The MP framework is demonstrated through sample calculations describing a lead-zinc concentrator.

Jan 1, 2015

By A. Taylor, E. Thorn Corthay, J. Farrell, L. A. Westfall, S. Borchardt

Mining and metallurgical industries need to minimize their greenhouse gas (GHG) emissions; Hatch specializes in conducting mining and metallurgical energy management assessments and optimizing productivity. Projects executed have demonstrated that there is a wealth of energy management, waste reduction, and process efficiency improvements that require no or low capital investment. Typical energy cost savings are on the order of 5% to 12%, with similar reductions in GHG emissions. Hatch generates Marginal Abatement Cost Curves to optimize the implementation pathway, maximizing carbon abatement and minimizing cost. The findings of a practical case study from Cameco are presented.

Jan 1, 2010

By M. Leahy

"Very little is known about the large scale fluid dynamics and associated distribution of copper in an operating electrowinning cell, yet they will have a major influence on mass transfer and plating quality. The CFD model in this work is used to simulate an entire EW cell with 60 cathodes and 61 anodes, or 121 anode–cathode pairs, elucidating for the first time the three-dimensional (3D) flow and copper distribution in an industrial cell. Two methods for the distribution of electrolyte are modelled:1. Downcomer method: electrolyte is fed by a downcomer at one end of the cell, overflowing at the opposite end.2. Manifold method: a horizontal manifold pipe runs the whole length of the cell and feeds electrolyte via small holes in the top of the manifold pipe.The recirculation that develops within each anode-cathode pair, driven by oxygen bubble generation on the anode, is similar to that seen previously in two-dimensional models of single anode–cathode gaps. However a more complex 3D flow recirculation is established, which involves flow of electrolyte down the side gaps (being a path of low resistance for return flow) as well as the usual return flow down the cathode side of each pair gap. The bubble-driven flow is not influenced by the mode of electrolyte distribution.The electrolyte flow due to the manifold and downcomer is somewhat secondary to the bubble driven flow. In the case of the downcomer distribution mode, the high injection velocity causes a very turbulent flow in the first 1–2 m down the cell from the downcomer, with several large vortices developing. This may lead to some sludge particles being entrained into the bulk of the cell.In the manifold pipe case, the jet from each hole is dissipated very quickly, within the first 10–20 cm. The jets are directed into the downward flowing zone of the bubble-driven recirculation, which leads to unstable and periodic behaviour on a large spatial scale.In both the manifold and downcomer cases, there is a marked two-zone vertical stratification in copper concentration."

Jan 1, 2016

By G. Bonin, R. P. Preston

"This paper presents a series of case studies where spherical camera photographs were used to generate 3D shaft models using photogrammetric methods. The shaft models were, checked for accuracy by comparing them to overlapping laser scan data, provided survey data or idealized shaft models. Short lengths of model were found to more accurately reproduce the shaft surface, with a best observed accuracy of 8 mm. Longer models encountered errors with accumulated errors as exhibited by slight deviations from vertical or slightly conical model shape. At present, the models are considered acceptable for general documentation and gross change detection. INTRODUCTION Shaft inspections are required by mining regulations in many jurisdictions and are commonly completed by trained mine personnel via visual inspections. This can be time consuming and prone to errors due to lapses in attention and the rapid travel rate required to inspect an entire shaft in a reasonable amount of time. Similarly, because of the time requirements, there can be impacts on other aspects of mining as a result of occupying the shaft for inspections. Spherical cameras with supplemental light systems offer a modern addition or alternative to conventional inspections. These cameras can be lowered relatively quickly to collect high definition, fully illuminated videos of the shaft that can be reviewed in detail later while the shaft returns to service (Gillis et.al., 2019). The use of cameras offers a further opportunity for valuable survey data generation from the same original data stream. The video data can be processed into three-dimensional (3D) models using Structure-from-Motion (Westoby et al., 2012) based photogrammetric methods. Depending on the quality of the source video and availability of survey control (required for all photogrammetry models) these models can be very accurate. Shaft surveying can be conducted with traditional theodolite methods but such surveys are time consuming and limited in their data density. Similarly, scans can be completed using conventional terrestrial laser scanners, but this requires a significant number of distinct setups to provide sufficient overlap between scans. Work is being conducted both on the laser scanning (SLAM, Durrant-Whyte & Bailey, 2006) and photogrammetry fronts towards kinetic scanning (Benecke, 2017) systems. The major advancement which is permitting these kinetic systems is Inertial Measurement Units (IMUs) which can provide localization in GPS denied environments and reduce errors associated with the open traverse format associated with shaft scanning."

Jan 1, 2019

By D. F. Scott

"DEFINITION OF THE REGION AND ITS BOUNDARIESTHE REGION of Western Canada covered by this re-port lies between the Precambrian rocks of the Canadian Shield and the structurally deformed rocks of the eastern Cordillera, extending northward from the international border to the 60th parallel. It is some 487,000 square miles in area, with a total sedimentary fill of about 535,000 cubic miles0>. It includes parts of the prairie provinces of Manitoba, Saskatchewan and Alberta and the northeast corner of British Columbia and forms part of the geological region known as the Interior Platform, commonly referred to as the Western Canada Sedimentary Basin. The bedrock comprises carbonates and evaporites of Paleozoic age that lie on Precambrian crystalline rocks and are over-lain by a relatively thick blanket of Mesozoic and Tertiary elastic rocks. The nearly flat-lying bedrock, covered by a thick mantle of glacial drift, forms the Interior Plains physiographic province."

Jan 1, 1970

By Brad Gunn

Our program has been dictated by the necessity of broadening our markets through converting potash chemicals to fertilizers more in demand than potassium chloride. To this end, we have undertaken studies on methods of preparing potassium sulphate or potassium magnesium sulphate by rather simple conversion. When mixtures of sodium and magnesium sulphates are reacted with potassium chloride, the ratio of sodium to magnesium is quite pertinent. A range of ratios has been selected and the conversions of potassium chloride to sulphate have been assessed by cyclic operations. Results from experimental procedures for producing potassium nitrate are also avail-able. The influence on recovery for systems including organic solvents is assessed for a variety of situations.

Jan 1, 1971

By A. Alwasel

Musculoskeletal disorders (MSDs) threaten the wellbeing and livelihood of a large number of construction workers incurring a significant cost to society. We present a new method to monitor and diagnose MSD risks in the workplace. The sensing unit of the system is an optical encoder encompassed within a non-intrusive exoskeleton to measure the joint angle of interest. This sensor can be applied to ball-and-socket and hinge-type joints of the human body, such as the shoulder, elbow, and knee joints. The system is contactless and does not require markers or cameras. Angle measurements are acquired directly without mathematical post-processing, thereby avoiding numerical noise and drift challenges. The system is a simple, robust, and deployable, but it currently lacks resolution of parallel degrees of freedom.

Aug 1, 2013

By Lorant B. Geller

Sixteen miners died tragically at the Paymaster gold mine at Timmins, Ontario in February, 1945, when a badly corroded hoist rope broke. The investigation of the Royal Commission that followed arrived at a number of recommendations (Investigations, 1947) aimed at avoiding future disasters of this kind. One consequence was the development, and legislated use in Canada, several decades ago, of powerful electromagnetic (EM) instruments for the nondestructive testing of mine shaft wire ropes. The authors have been involved for many years in the design, production, and testing of EM instruments (Geller and Udd, 1990 and 1992, Geller and Kitzinger, 1991, Geller et al., 1993). Since the mid-1990s particular attention was paid to the design and operational results obtained from the computer- controlled portable MagnographJ II wire rope tester (Geller et al., 1995 and 1998). In the present article the authors summarize further hardware- and software-related developments of this instrument. Further, an account is given of the results obtained from the most recent design known as the PermaScanJ testing system. This is also a computerized dual-function system. In it, however, the sensor head is designed primarily, if not solely, for permanent installation and for remotely controlled operation. This represents a basic departure from traditional designs, which were intended for ad hoc temporary installations. The remotecontrolled instrument described in this paper has now been in operational use for more than 4 years.

May 1, 2003

By H. Brodie Hicks

"THE REVIVAL of the Mayo mining camp, with particular reference to the activities of United Keno Hill Mines, Limited, has been one •of the more spectacular and also one of the most important of the post-war developments in the Canadian mining field. The geological location of the camp, coupled with other natural disadvantages, have in the past limited the mining area to small-scale, highgrading operations, but the post-war improvement in metal prices has now broadened the possibilities and has led to the considerable success achieved by United Keno Hill Mines, Limited, and the present boom-type development by a whole host of newcomers to the field.LocationYukon which has an area of 207,000 square miles, is showing ever increasing possibilities as a mineral source of great value and more and more attention is being focussed on the Territory. The accompanying generalized map (Figure 1) shows the main transportation routes and mining districts.The Mayo Mining District comprises roughly the eastern two thirds of Yukon Territory lying north of McMillan river and south of the Peel. The district was one of the first in the Territory in which placer gold was discovered, but the occurrences proved of minor importance. Other minerals reported include ores of tungsten, tin, antimony, and several other metals, but of primary importance have been the ores containing silver-lead-zinc-cadmium now being developed and mined in the Keno area. Similar ores have been found over a very considerable area, extending some 50 miles north, 15 miles east, 30 miles west, and 10 miles south of the townsite of Keno Hills, Keno City, a total area of 2,700 square miles."

Jan 1, 1952

By M. Somppi, D. Weirmeir, Z. Yamak

"Milling operations commonly employ activated carbon to capture complexed gold from lixiviants in leaching processes. As the carbon moves through pipes, pumps, vessels, kilns and other processes in the gold leaching circuit, this consumable may experience losses by various mechanisms like attrition, breakage, and rupturing. Whenever possible, capturing the fine gold-bearing carbon portion of this stream could provide value to milling operations at low capital cost and manageable financial risk. Identifying, testing, and validating the successful payback of a low-tech flocculant system is described. However, the work more closely explores a Monte Carlo risk-based methodology for understanding the potential payback of this project at various confidence levels – an approach that many improvement projects can follow where some level of uncertainty exists.INTRODUCTION Gold milling operations commonly employ activated carbon to adsorb gold from solutions. Normal handling causes the carbon particles from this material to abrade, break, rupture to a size that becomes too small for further use in the process. Operations often concentrate on capturing the fine particles because gold is associated with the carbon and this metal content can be a valuable revenue stream for toll processing. However, the small particle sizes become difficult to separate from the process and can ultimately leave the facility in the waste stream. Hence, operations often place a great deal of care in capturing as much fine carbon as possible by a variety of methods including using screens, settling tanks, and chemical methods. Retrofitting a circuit to capture more carbon fines is common but can expose the operation to financial risk. Approaching this potential improvement by leveraging a Monte Carlo methodology can be effective in understanding the risk and the associated payback of a project at various confidence levels. This method provides a strong framework for capital go-no-go decisions and the structure to validate the potential project success before implementation."

Jan 1, 2019

By P. G. Smith, A. Axiuk

The objective of this paper is to present, from a practical perspective, a review of the most relevant maintenance procedures that are accepted or prescribed to be the most effective in optimising service life potential and to ensure continued safe use of steel wire ropes for shaft mining applications. The paper will address the most common operational issues encountered in the care and operation of shaft ropes for both conventional drum hoists and multi-rope friction winders. For each distinct maintenance procedure presented, a limited amount of theory is discussed to identify the underlying mechanisms at play that must be addressed and to emphasize the logical basis for the recommended course of action. It is recognised that each installation is unique and that the recommended maintenance procedures may not always be practical or cost effective from an operations standpoint under select circumstances, however the intent remains to promote industry best practices for the knowledge and benefit of the mine hoisting community, from experienced maintenance personnel to new entrants to the industry alike.

Jan 1, 2023

By J. Seo

We propose a dynamic biomechanical simulation method that uses motion capture to evaluate the risk of Work-related Musculoskeletal Disorders (WMSDs). Statistics show that WMSDs accounted for 33% of all non-fatal occupational injuries and illness in construction in 2009, and were a leading cause of temporary and permanent disability. Present methods rely largely on self-reports from workers, observational techniques, and direct measurements of motion and muscle activity to assess awkward postures, physical loads, repetitiveness, and the duration of exposure. While these methods have helped to prevent WMSDs in construction work, they may not be suitable for estimating the internal tissue loads associated with WMSDs. We propose a dynamic biomechanical simulation method to estimate internal forces and moments at each body joint of construction workers with motion capture data. Particularly, we explore the biomechanical loads by simulating active 3D musculoskeletal models based on measured postures and movements. To demonstrate the feasibility of this approach, we studied a ladder climbing task using a portable ladder under controlled laboratory conditions. Postures and motions were determined with a commercial motion capture system (e.g., VICON). The results were analyzed to investigate the feasibility of identifying risk factors based on biomechanical simulation. The results show that the proposed approach allows us to determine the biomechanical basis for WMSDs, and to identify postures and movements associated with excessive physical demands on each body joint. When combined with marker-less motion capture which is our ongoing work, the proposed approach has the potential to assess an individual?s motions and to provide personalized feedback for the purpose of reducing biomechanical loads and WMSD risk in real workplaces.

Aug 1, 2013

By Kris Inwood

"In 1879, when the Dominion government initiated its controversial program of industrial promotion, iron smelting in Canada was limited to one company producing coke iron on the mainland of Nova Scotia and three small charcoal blast furnaces in Quebec. There was no steel production. By the eve of the First World War, iron and steel were being produced in very large quantities, the companies active in 1879 had disappeared and new centres of integrated iron and rolled steel production at Hamilton, Sydney and Sault Ste. Marie had come to resemble the industry as we know it today. The most dramatic change was that at Sydney, Nova Scotia, where in the early 1900s, two steelmaking companies established works. The Sydney developments have been explained as the result of resource discovery and technical change. W.J. Donald, in his authoritative account of the Canadian iron and steel industry, observes:(1) ""The most rapid growth of the Canadian iron and steel industry has occurred since 1897 ... The remarkable growth has been caused largely by the new conditions of the industry. The discovery and use of Newfoundland ores, together with the availability of Cape Breton coal, has made the Nova Scotia industry not only possible but profitable .... It is a safe conclusion that the Canadian industry would not have been an important one, had it not been for the discovery of the Michipicoten and especially the Wabana (Newfoundland) ores:' Donald also argues that metallurgical progress had been necessary to render the ores valuable. ""Newfoundland ores ... contain a considerable amount of phosphorus, and were made available for steel-making by recent inventions:' The purpose of this paper is to re-examine Donald's story. It will be argued that the origin of steel-making at Sydney is somewhat more complicated than Donald has indicated. The difficulty with Newfoundland ore extended beyond its phosphorus content and a resolution required more than the basic open hearth furnace identified by Donald. Moreover metallurgical change was only one of several developments necessary to induce industrial investment at Sydney. Surprisingly, however, the discovery of iron ore in the late nineteenth century does not appear to be part of the explanation."

Jan 1, 1999