Search Documents

By A. E. Dyment

In formulating an explosive for any specific set of conditions, various factors must be taken into consideration. Is it to be subjected to water or moisture? .If so, it must be designed to have an inherent ability to resist water. Is it to be used in confined spaces underground, where ventilation is limited? If it is, it must possess qualities enabling it to form, upon explosion, the minimum quantity of noxious gases, such as carbon monoxide or oxides of nitrogen. Is it for use where low temperatures may possibly prevail? If so, it must be capable of resisting such temperatures without freezing. Is it for use where dust or inflammable gases may be present? If it is, then it must be so formulated as to produce, upon detonation, a flame of the lowest possible temperature and the shortest possible duration, in order to lessen the chance of ignition of such gas or dust. This is actually the essential property of a permitted explosive, and it is undoubtedly the most important characteristic of an explosive which is to be used in gassy or closed-light mines. This being the quality that distinguishes permitted explosives from other types, it is interesting to investigate the ways and means by which the low-flame-temperature characteristic is obtained . Generally speaking, such explosives are so designed as to contain comparatively small quantities of nitroglycerin and relatively large quantities of the strength-producing salt, ammonium nitrate. This ingredient does not develop as high a temperature upon explosion as does nitroglycerin, so its presence, in large measure, in place of nitroglycerin results in an explosive which has an inherent low-flame-temperature characteristic, as opposed to one which is .made up largely of nitroglycerin, which would ordinarily be in the high-flame-temperature class. Additions are also made of flame-quenching salts such as sodium chloride, ammonium chloride, and up to a certain limiting percentage of sodium nitrate. These salts, with the exception of the last, do not ordinarily take an active part in the explosive reaction, being present primarily to absorb heat liberated by the reacting ingredients.

Jan 1, 1947

By J. B. Mawdsley

"The Red Lake Gold Shore mine is 4/5 mile west of the town of Red Lake, Ontario, and a mile northwest of the Howey mine. It came into production in August 1936, and in a little over 2 years produced 21,099.58 oz. gold from 83,949 tons milled.An investigation of this deposit was made by the writer during parts of September and October, 1937t. The geology of the deposit is also discussed by H. C. Horwood(2) , and the characteristics of the ore were investigated by the Bureau of Mines, Ottawa (1).The orebodies are pipe like and close together, in a north-northwesterly trending zone of dykes, veins, and shear zones in a granodiorite stock, just south of a pronounced valley with a trend of N.65°E. believed to lie along a strong shear zone and fault . The dykes, veins, and mineralization are believed to have been successively emplaced along structures having three general trends and that were due to compressive stresses that alternated, at least four times, from west of north to east of north. In common with many other gold deposits, the gold mineralization here occurred late and followed the last east-of-north stresses.WALL-ROCKSThe mine is within the Dome stock, % mile from its southeast margin. Near the mine the rock is a pink hornblende-biotite granodiorite, grading within short distances, but not abruptly, into a dark grey variety. Near the workings at least, scattered small inclusions form about ½ to 5 per cent of this body. Most of them are fine-grained, angular, or partly rounded, greenstone fragments, but some have been partly granitized and feldspar has been developed in them."

Jan 1, 1954

By J P. Bolduc, P. E. Pelletier

Preceded by brief general considerations such as the development of the mining industry in. the Province of Quebec, the choice of plant location, the types of problems studied etc., the paper gives a complete description of this new research and treatment center for metallic, non-metallic and asbestos ores. Facilities for carrying out operations in the three sections of the plant -the sampling section, the ore treatment section and the asbestos section -are fully discussed as well as laboratory facilities for (a) the preliminary testing of ores prior to pilot plant treatment and (b) the grading and testing of asbestos fibre. AT THE beginning of the century, the annual value of the mineral production of the Province of Quebec stood at the $2,500,000 level. Twenty-five years later, it was just under $24,000,000. In 1950, half a century later, it was slightly in excess of $200,000,000. But in 1959, in the span of only nine years, it

Jan 1, 1962

By C. A. Clark

The Chagres Smelter is located 80 kilometres north of Santiago - Chile, in the middle of an agricultural valley which is also one of the poorest districts in the country. This condition sets the main focus for the smelter's Corporate Social Responsibility (CSR) programmes, which ultimately aim at building self sustainable social and economic capital in accordance with the local capacities. With the help of Anglo American's SEAT (Socio Economic Assessment Toolbox), a corporately developed instrument designed to help the operations understand the needs of the communities and the impacts of those operations, the Chagres Smelter implemented several programmes, such as the CETTA (Experimental and Applied Technology Transfer Centre) programme. This project started in 2003, and consists of creating a centre for the transfer of sustainable techniques and skills for the small agricultural and livestock producers that live in the rural areas near the Chagres Smelter. Its main impacts are: Improved production quality (goat cheese and bee honey) and access to relevant markets, improved training and self-sustainability levels of producers, enhanced socio-economic level of the District's inhabitants by improving their income earning opportunities and technical knowledge, creation and promotion of a local brand as a symbol of quality products from the valley and a positive environmental impact of good breeding and native flora protection practices in the area. Other relevant social programmes are the 'Environmental Strivers', which created a recycling centre in the community; and the 'Beautiful Valley" project, which provides management knowledge and skills to local youngsters and leaders who can contribute to finding solutions for local environmental needs.

Jan 1, 2007

By A. Trusiak

"Increasing energy costs in mineral processing is making it necessary for tighter controls over various parts of the concentrating process. Continuous monitoring and control of critical process streams can be easily performed by today's many computer systems. Indeed, the list of successful applications of computers to grinding and flotation control continues to grow. The day is rapidly approaching when the use of computers within concentrators for either process control or simply metallurgical accounting will no longer be a luxury, but a necessity. The benefits from such applications far out weight the initial investment.This paper describes the current application of a process control system at Brunswick Mining in north-eastern New Brunswick. Emphasis is placed on the control of a CuPb flotation circuit, and the benefits derived-from this control.No. 12 Cu-Pb Flotation: The complex nature of the Brunswick flotation process has been described else-where. 1,2,3 Four final concentrates are eventually produced, these being a Zn concentrate assaying 53% Zn, a 30% Pb concentrate, a 20% Cu concentrate, and a bulk Pb Zn concentrate assaying 35% Zn and 17% Pb. The Cu concentate, Pb concentrate, and bulk Pb Zn concentrate are all derived from a primary CuPb concentrate assaying 26% Pb, 11% Zn and 1.8% Cu.The No. 12 CuPb circuit produces approximately two thirds of the total primary CuPb concentrate. No. 12 ore, assaying 3.5% Pb, 9% Zn, 0.25% Cu and 100 g/tne silver, is ground in two parallel grinding circuits. Each line uses a 3.2 x 4.2 meter rod mill in closed circuit with two parallel 3.2 x 3.9 meter ball mills. Ball mill and rod mill discharges are classified in two stages of cycloning. The secondary cyclone overflow, or flotation feed, is controlled at 65% passing 37 microns."

Jan 1, 1981

By Lynn I. Kelley

Potash is the primary industrial mineral produced in Saskatchewan, followed, in terms of gross value, by aggregate, sodium sulphate, salt, potassium sulphate, peat, clays, silica sand, calcium chloride brine and "clinker." Potentially economic deposits of kaolin, diamond and building stone are under evaluation.

Jan 1, 2001

By D. H. Stonehouse

Of the f ive Canadian cement producing regions- Atlantic, Quebec, Ontario, Prairie and Pacific-Ontario has the greatest capacity and normally produces the most cement. However, during the last 5 years the greatest activity within the industry in Canada has been in the Prairie and Pacific regions where major capacity increases have taken place. Most Canadian cement companies produce normal Portland, high-earlystrength Portland and sulphate resisting Portland cements. Some companies also manufacture moderate Portland cement, and low-heat-of-hydration Portland cement. Escalating energy costs highlight the need for technology research into more energy-efficient equipment for the energy-intensive cement industry. The industry is well integrated and plants are well situated to support construction in Canada. Expansion into the United States has become common during the past decade.

Jan 1, 1984

By R. L. Bruening, L. Navarro, Izatt. S. R., R. Adiga, R. M. Izatt, N. E. Izatt, A. Sharma, N. R. Patel, B. V. Rao

Bismuth is a notorious contaminant in the electrolytic refining of Cu that can cause cathodes to fail to meet ASTM International standards and not be suitable for use in Cu rod and other downstream products. Bismuth can significantly decrease electrical conductivity, decrease the mechanical strength of the annealed wire, retard recrystallization, and sometimes induce hot shortness during the hot rolling process in the production of rod. As a result, the control of Bi in the refinery tankhouse must be carefully managed. This paper describes how SuperLig® Molecular Recognition Technology (MRT) is being used for Bi removal at the Birla Copper Dahej Copper refinery. The operation of the SuperLig® MRT Bi removal plant is described and data on Bi removal efficiency are presented. INTRODUCTION Hindalco’s Cu division, Birla Copper, operates one of the largest Cu refineries in the world at Dahej, Gujarat; India. The main feed for this refinery is produced at the company’s smelter. Due to its massive production capacity, this operation mainly relies on imported Cu concentrates resulting in a variety of metals being carried out as impurities in the Cu anodes because pyrometallurgical technologies alone are not enough to remove them to the extent required. Metal impurities found in Cu ores include Fe, Zn, As, Pb, Bi, and Sb. During electrorefining, less noble metals dissolve in the electrolyte gradually increasing their concentrations creating the need for electrolyte control mechanisms that remove these impurities with varying degrees of success (Wang, 2004; Navarro et al., 2013.) Bismuth is one of the most significant impurities in a Cu refinery because it has the lowest ASTM product specification. This situation is critical because the Bi potential is very close to that of Cu making it possible to plate in the Cu cathode directly. Also, Bi can precipitate at high concentrations causing floating slimes and reduction of current efficiency (Ballinas, San Miguel, Munoz, & Gyves, 2003). Production of high purity cathodes from feed stock containing a diverse range of metal impurities becomes a major challenge in the refining of Cu (Izatt et al., 2015). In this work, the purification strategy followed by Birla Copper for the removal of Bi using a separation process based on MRT is presented, outlining the loading and stripping performance of SuperLig®83 and the benefits of using MRT over other lower selectivity methods where hazardous materials are produced instead of high purity products.

Jan 1, 2019

By R. Khettabi

The mechanical, thermal and bioproperties of titanium alloys allow their wide use in different industries. Compared to aluminum alloys, titanium alloys are very tough, making them that much more difficult to machine than aluminum alloys. Most studies conducted on these types of materials have mainly covered and made comparisons in terms of cutting speed, cutting force and mechanical properties. Recently however, their sustainability and environment parameters have begun to attract significant interest, and it has been found that machining processes generate particles that can be harmful for health and the environment. In this paper, particle emission is investigated during the turning of the titanium Ti6A14V and 6061-T6 aluminum alloys.

Jan 1, 2011

By C Kumar

Scaffolds are temporary structures built to facilitate construction activities on site. A considerable amount of resources are allocated to scaffolding on industrial projects. Variability in geometrical features and space accessibility of structures on industrial projects, in addition to involvement of different trades that share the use of scaffolds, requires an extensive understanding of scaffolding requirements. Hence, it?s important to plan and estimate scaffolding man-hour requirements for the different construction areas on an industrial site. Contributing factors involved in such estimates include the list of trades that work in a construction area, trade working hours, volume of work, geometry of equipment erected, etc. A simulation template for predicting scaffold erection man-hour values for individual construction areas in an industrial project was developed in Simphony 4.0. The template is based on mapping the geometry of equipment and other factors to man-hours of scaffold work. The template facilitates the use of distributions as inputs and produces a range estimate of scaffold man-hours. The mapping is based on a linear regression model derived from existing project data from PCL Industrial Management Inc. The template is being further developed to incorporate the ability to predict scaffold erection schedule and material requirements based on construction work areas or equipment lists of an industrial construction project.

Aug 1, 2013

By C. Boudreault, M. Fortier, S. Fafard

In the forging industry, the increasing trend is to use DC cast billets as forging stock to replace extruded stock. However, there is little technical information available in open literature. In order to gain a better understanding of the behaviour of cast stock during deformation, a study was initiated to evaluate the impact of an homogenisation treatment on the billet prior to cold forging. Axisymmetric upsettings of cylindrical samples machined from DC billets were achieved in order to evaluate and compare flow stresses, crack initiation and propagation. Results show a 30% decrease in flow stress after homogenisation. Observations of the deformed samples show major cracking for the as-cast material. Optical microscopy and SEM observations have related the crack initiation to decohesion around ß -AlFeSi particles and subsequent growth along the constituent path. Homogenisation effectively breaks up and transforms the ß phase, present as platelets in the cast product, into smaller spherodised a-AlFeSi particles. This has the effect of preventing crack growth in the forged product. The homogenisation treatment also resulted in the reduction of Mg and Si in solid solution. The softer matrix generated 29% less die wear when compared to the as-cast structure. Based on the results of this study, it is thus recommended to homogenise cast billets prior to cold forging.

Jan 1, 2006

By M. A. Creaney

"The Construction Group is responsible for the construction of all of Placer Dome’s major projects and contributes to the development of most major feasibility studies. This group includes an international collection of Placer Dome people who have built mines in Papua New Guinea, Australia, Chile, the United States and Canada. This paper outlines the changing role of the Construction Group from the early days of single projects to today, when several projects are in various phases from feasibility to construction. The projects’ total annual budgets have from time to time exceeded one billion dollars. IntroductionAs the competition increases globally between the major gold mining companies, the impetus continues to build mines at the lowest cost with the shortest construction schedule. Placer Dome has more than met that challenge by building mines around the world at a pace that was not contemplated 15 or 20 years ago. Since 1960, Placer Dome has built 30 mines and expansions at a cost of nearly 4.5 billion dollars.In the last six years alone, Placer Dome has built 14 mines and expansions, worth 2.6 billion dollars. The company’s success is due primarily to Experience, Innovation, People and Standards.The diversity between projects, let alone the pace, has been a challenge. Placer Dome has built mines around the world in a variety of extreme climates and distinctive cultures. The construction experience gained from these projects has allowed Placer Dome to develop an extensive knowledge and data base making it easier to “fast track” projects.Through the years Placer Dome has developed a human resource base. It now has an experienced and adaptable core team of people able to set up construction projects and build mines anywhere in the world. By developing standards and systems to support the projects they can act as soon as a new project is approved, and complete the projects quickly and effectively. The result is that Placer Dome now has the construction expertise to build its own mines, giving them the competitive advantage that allows them to design and construct a mine in the least time at the lowest capital cost. This was demonstrated in March 1997 with the completion of the construction of two new mines in 12 months."

Jan 1, 1998

By Ursula M. Franklin

Old iron nails are one of the most common objects which entice the general public to ask questions about the history of metallurgy. There is a lot of history in old nails - history of the manufacturing industry, and social and economic history. Nails, therefore, are fine teaching tools; whether students have to acquire metallurgical skills or explore the structure and properties of wrought iron, whether they want to look into the history of inventions and the development of machinery, studying nails tells a story better than any teacher or any book. I have used this approach often and the following note is based on several student projects, particularly the work of Carmina Herrero and Vicky Marchant. Nails, those essential metallic fasteners, have long been with us. Their size, shape and design is basically a compromise between the makers' ability to control and manipulate material and the demands of the intended application. There were copper and bronze nails in antiquity, but in this paper I want to deal only with iron nails. In Rome, iron nails were common, and Cleere carried out the fine metallographic investigations on a large stock of nails recovered from a Roman fort site in Scotland. Those nails were hand forged; sorting them at the site on the basis of length, shape of head and shape of shank (in cross section) indicated that there seemed to have been some nail standardization. It appears that the Roman smiths used a series of heading dies starting with a 1/s-in. size. Each successive size increased by approximately 1/16-in. The metallographic inspection of the microstructures of the nails showed that the smaller nails were made in the one operation; i.e. both the tapering and the formation were accomplished on the heated rod without reheating. However, in the case of the larger nails, the nail had to be reheated for the tapering after the head had been forged. Most nails were tapered on all four sides of the shank and the shanks were square in cross section; only one group had rounded shanks. Most heads were flat disks, but in one group the heads were pyramids and another group had conic heads. Figure 1 shows the procedure used to produce the pyramidal heads. Obviously, Roman nail making was sophisticated and each nail design was meant for a particular use.

Jan 1, 1999

By R. D. Brown

"An adequate level of R & 0 is crucial to achieve gains in productivity and to strengthen Canada' s position in an increasingly competitive world ." So stated Finance Minister Jean Chretien in his April 10, 1978 budget speech, on announcing a new measure designed to increase the productivity of Canadian industry and to assist in the creation of new technology. The effect of the new measure, which permits an income tax deduction of 150% of certain research and development (R & D ) expenditures , can reduce the after-tax cost of a marginal dollar 's worth of such expenditures to as little as 20 cents . This article discusses the income tax treatment of R& D expenditures in general, and describes in particular the income tax incentives which relate to R& D.

Jan 1, 1978

By A. Haldar

The major problem encountered in the casting of hypereutectic Al-Si alloys is the stoppage of flow below the rigidity level of solid fraction. In this study, the flow stoppage mechanism was studied using three Al-Si alloys with 14%, 18% and 22% silicon. The horizontal foam patterns used were 12.50 mm (0.50 inch) wide with two section thicknesses 12.50 mm (0.50 inch) and 6.25 mm (0.25 inch) with a common sprue. The primary silicon distribution along the length of the casting was studied to determine the mechanism of flow stoppage. It was found that the surface of the flow tip of Al-14%Si alloy was smooth with a few undulations. As the silicon level increased, undulations at the flow tip increased. The number and size of undulations were maximum for the Al-22%Si alloy. Microstructural analysis using optical image analyzer revealed that the flow tip consisted mainly of eutectic silicon in the aluminum matrix and a few primary silicon crystals (PSC). The PSC were in the interlocked condition few centimeters behind the flow tip. It was also found that the gap between the flow tip and the PSC concentrated area increased with an increase in silicon level. Phase characterization was done with SEM-EDX to identify the precipitating phases.

Jan 1, 2007

By R. U. Seneviratne, B. K. Ahlgren

In this paper we follow various technological discoveries and developments in the purification of minerals and metals in the mining industry by ion exchange. For approximately 100 years, ion exchange has been a known and variously applied purification and separation technology used by scientists and producers. It would seem obvious that the producer’s objectives have always been to achieve the highest quality products and the lowest operation costs, but also with the least amount of technological complexity. As a strategy to reach these goals, much effort has been expended in the quest to improve continuous ion exchange (CIX) systems by reducing utility needs and resin degradation or loss while at the same time improving productivity and reliability. Recent developments from a number of companies have pushed equipment boundaries, resulting in a variety of unique commercial equipment designs each with a varying degree of success. The challenge set forth for all new designs has been a truly continuous process with no sacrifice in the afore mentioned benefits. One very recent equipment design based on system symmetry appears to meet many of these objectives with greater flexibility and less complexity resulting in better economics for the producer.

Jan 1, 2014

By K. Iturralde

The article discusses the possibility of automation in refurbishment processes of social dwelling built from 1950 to 1970. These massively produced buildings were mostly designed prior to the law enforcement regarding thermal insulation or accessibility. Nowadays, many of these buildings are being retrofitted. The article focuses on the works in the external envelope. The task of renewing the whole social building stock is big and it requires a systematic process that facilitates a rapid upgrading, without neglecting the specific situation of each case. How could an automatic refurbishment process of these buildings be defined? The process should start with the data collection of the building and the creation of a 3D model using software such as BIM. The project, drafted in 3D, should facilitate the manufacture of building elements by robotics. In turn, it should be noted that during the assembly at the site, the pieces must be fixed quickly and efficiently. Is it possible to implement an automated process for the refurbishment of apartments built in the second half of the twentieth century? To approach the answer, a virtual refurbishment project is performed. The article focuses on the rehabilitation of the building envelope. Furthermore, it gives special attention to the double skin facade. It is well known that a second skin in this type of building can be an element that integrates several functions. Finally, needless to say that refurbishment of residential buildings is a need in our society. By extending its life cycle, robotic refurbishment provides more favorable socioeconomic and environmental capabilities than the sole construction of new buildings.

Aug 1, 2013

By K. G. Markkola

The Minera Candelaria concentrator was commissioned in August 1994, and in October 1997 it doubled its grinding capacity. The concentrator was designed to treat 56,000 metric tonnes of copper ore with a primary crusher, two grinding circuits, pebble crushing, and flotation. The grinding circuit includes two 11.2 m (36 ft) diameter by 4.6 m (15 ft) long semi-autogenous (SAG) mills, each fitted with a 12 MW motor. Throughout the history of Candelaria, different strategies have been developed to maximize the plant's operational time, strategies that include increasing the life of the SAG mill liners and reducing the time involved in changing these elements. This work describes the improvements made in the design of the liners, the change planning, and a new strategy to change the liners with the purpose of increasing their use and throughput.

Jan 1, 2007

By Douglas R. Schmitt

In general, knowledge of the state of stress within the Antarctic lithosphere remains largely unconstrained due in part to Antarctica?s inaccessibility and because of the paucity of seismic focal mechanism solutions. As such, an important component of the ANDRILL project was to acquire new information on the stress directions and magnitudes within the upper crust. Extensive fracture mapping of the core and oriented ultrasonic televiewer logging were carried out to provide strong constraints on both stress orientations and the faulting regime. The first hydraulic fracturing stress determinations in Antarctica were also carried out to provide complimentary stress magnitudes. These measurements were accomplished using a wire-line transported hydraulic fracturing system consisting, essentially, of two synthetic polymer packers that were inflated to isolate the 1-m long pressurization interval. The tests were conducted at the end of the drilling and logging in a ~130-m section specially drilled below 1000 mbsf (nearly 1500 m from the rig floor) for hydraulic fractures. This zone was drilled primarily through competent, dense, and low permeability diamicts. The core fracture and televiewer logging information was used to site twenty separate measurements. Classic hydraulic fracturing pressurization records with unambiguous breakdown and fracture closure pressures were obtained in about half of the measurements. The remaining tests provided fracture propagation and closure pressures that are consistent with the classic breakdown curves, but they did not include a clear breakdown pressure and are indicative of the reopening of either natural or drilling induced fractures in the wellbore wall. The preliminary analysis of the results are in generally good agreement with the stress directions indicated by the core fracture logging and the stress regime suggested by the character of the drilling induced core fractures.

Jun 1, 2012

By O. B. Horne, R. O. Morgan, C. E. Anderson

"Air-photo interpretation and photogrammetry are two of the most effective and versatile tools available to the petroleum industry. The techniques have proven successful in providing solutions to many of the problems encountered in the design and construction of oilfield projects.Although most technical personnel are aware that air-photo interpretation and photogrammetry are useful in the selection of routes for roads and pipelines, few realize the true scope of the techniques or the wide variety of areas in which they are applicable.This paper briefly describes the principles involved, and reviews a number of typical applications of particular interest to petroleum companies. Excessive detail is avoided, rather the emphasis is placed upon the wide spectrum of possible applications. It is stressed that on-the-ground examination generally is a necessary adjunct, and that there are certain limitations to the techniques discussed.Properly applied, however, air-photo interpretation and photogrammetry can offer significant advantages in terms of time, flexibility, secrecy and economy."

Jan 1, 1968