Search Documents

By N. B. Brown

ABSTRACT The effect of a low4emperature stress relief at 232.2°C. (450°?F.) on the fatigue properties of shot-peened SAE. 1080 steel has been investigated. Specimens of the steel were first annealed. One half of the steel bars were then normalized and the other half were water-quenched and drawn. Specimens of the steel with each heat treatment were tested in tensile, notched bar impact, and fatigue. The fatigue specimens were test in air and water in R. R. Moore high-speed rotating bending machines in the following conditions: un-peened, peened, and peened-and stress-relieved at 232.2°C. ( 450°F.) The 'endurance life' and fatigue properties of specimens given a stress relief heat treatment after shot peening were superior to those of specimens given a smooth machine finish or shot peened. INTRODUCTION THIS investigation was initiated to obtain preliminary information on the effect on the fatigue resistance of shot peening the machined surface of a high-carbon steel similar in composition to that used in hollow drill steel. The data obtained in this investigation could be applied in analysing the application of shot peening hollow drill steel shanks. It is well known that the 'endurance life' and fatigue limits of steel are greatly ?improved by shot peening. References to this in the literature are numerous.

Jan 1, 1951

By P Hulteberg

In this article, an integrated catalytic reactor design approach to produce PEMFC-quality hydrogen is evaluated. The design is based on a high level of heat exchanging perfonned internally, highly active noble metal catalysts and a woven wire mesh catalyst support system. It consists of an integrated steam refonner and a catalytic burner section, a water gas shift section and a preferential carbon monoxide oxidation section. The reactor design is described and experiments perfonned to evaluate the two reactors built are reported. The two reactors have a maximum output of 3 Nm and 10 Nm3 hydrogen/h respectively. In the larger unit, a total of six fuels, three gaseous (methane, natural gas and liquid propane gas) and three liquid (naphtha, ethanol and methanol), were evaluated. The larger unit was also used to investigate how variations of parameters such as steam-to-carbon ratio in the steam reforming part of the system and the relation between oxygen and carbon monoxide in the preferential carbon monoxide oxidation affect the reactor perfonnance. The smaller unit was used, after implementing automatic control, to run a system life time test for 480 h. The refonner system perfonned according to specifications on almost every aspect.

Jan 1, 2005

By Allan J. Guse

The primary limiting factor for hoisting capacity from great depths is the self-weight of the typical steel wire ropes used for mine hoisting. Steel wire ropes possess properties making them very suitable for mine hoisting including high strength and durability, but have the negative characteristic of being relatively heavy in comparison with their strength. Also, as hoisting depths increase, the service life of steel wire ropes decreases due to the higher stresses and physical effects on the ropes. The significantly higher strength-to-weight ratio of synthetic ropes compared with steel ropes offers the primary advantage of hoisting a larger payload with a similar size rope and hoisting plant. The beneficial properties of synthetic ropes could be used to improve the overall economics of deep underground mining both for new deep shaft projects and for existing mining operations expanding to deeper orebodies. A research and development program has been initiated to evaluate the suitability of a fully synthetic rope for the mine hoisting application, including rope discard methodology and NDT testing. The three phases/projects are: 1) proof of concept with focus on coilability under load (successfully completed in 2012); 2) high speed and load durability optimization & NDT Development; and 3) in-situ mine trial.

May 1, 2013

By T. J. Wells

THE blast furnace is the base of the steel industry, since there is no commercially practical way of converting iron ore directly into steel. In three hundred years, the blast furnace has developed from a small unit using charcoal as fuel and producing about one ton of iron in twenty-four hours to a furnace making upwards of 1,500 tons a day. The principle of the blast furnace is briefly this: A descending column of stock, consisting of ore, fuel, and flux, is met by an ascending stream of gases, consisting in part of gases formed by the combustion of the fuel and in part of pre-heated air which is blown into the lower part of the furnace. The flux combines with the impurities in the ore and the ash in the fuel to form slag, which is drawn off as liquid.

Jan 1, 1943

By C. Fortin

The subject of gold flotation has been reviewed extensively in a number of publications. The focus in most of these reviews has been on the theories of gold flotation as well as the physical and chemical effects that may impact the efficacy of the gold flotation process. It is evident that the current status of gold flotation chemistry as it is being applied in industry has not been addressed widely. It is the intent of this paper to review current gold flotation practice and how these applications tie in with the current understanding of the chemistry of gold flotation.

Jan 1, 2011

By R. G. Helberg, S. M. Rebelo

"Copper and cadmium are removed from the zinc sulphate solution in primary purification by cementation reaction followed by filtration. The solids are sent to the cake leach section where zinc and cadmium are recovered from the copper rich slurry. The copper solids from cake leach are filtered, bagged and sold. In order to achieve a lower cadmium copper cake, an altered process flow is suggested. It is proposed the primary purification be split into two steps for individual removal of copper and cadmium. INTRODUCTIONCopper cake is a product of primary purification, also known as copper and cadmium removal. Copper and cadmium are removed by cementation reaction in four stirred reaction tanks. The slurry is then filtered through Shriver manual plate and frame presses with the solution advancing to the next stage of purification, hot zinc purification (HZP). The solids from primary purification are further processed at the cake leach section where zinc and cadmium are separated from the copper rich slurry. Cadmium and zinc are dissolved in the cold cake leach tanks using spent electrolyte. Cadmium is recovered from this cadmium rich solution by cadmium sponging, leaching and electro-winning circuits. The residue from this cold leach step is further leached using spent electrolyte at a temperature of 85°C. The copper rich solids from hot cake leach are filtered on a drum filter and bagged in 1 ton bulk bags for shipping to buyers.Current assays of copper cake are shown in Table 1. The goal is to produce a copper cake product that is below 0.5% cadmium."

Jan 1, 2012

By John A. Hansuld

Geochemical dispersion of metals under various environmental conditions is discussed within the frame-work of Eh (oxidation potential) and pH (acidity). In general, two aspects are considered -(1) the oxidation of certain primary sulphides in the outcrop or sub-outcrop environment, and (2) the movement of metals in different dispersion media. Practical applications of each are illustrated by means of exploration case histories representing environmental conditions in the Canadian Shield, the southwestern United States and the Caribbean.

Jan 1, 1966

By G. Van Weert, O. Wang

ABSTRACT: When exposed to microwaves, rocks containing sulphides adsorb energy preferentially over barren gangue and quickly become warmer with minimal energy consumption. This effect makes subsequent machine sorting of ore from waste rocks or overburden possible using infrared sensing. This paper reports on the 2450 MHz microwave response of a variety of sulphide minerals by mesh size and spatial distribution, as they might occur in ore rocks. The implications for infrared ore sorting are discussed.

Jan 1, 2011

By Sabry A. Sabour

Metal price is among the key variables in the open pit optimization and the economic evaluation process. The common approach to handle metal prices in open pit mine planning is to optimize the ultimate pit and the mining schedules using a fixed, flat metal price. In this respect, metal price is assumed to be known with certainty throughout the entire mine life, which in some cases can reach 80 years. Given the volatile nature of metal markets and the metal price cycles, the conventional pit optimization approach may generate sub-optimized mining plans, which results in either extra costs to mining projects or lost revenues, or both. Long-term operational decisions such as future pit expansions, beyond the currently optimized limits, cannot be handled using the pit optimization approach based on flat metal prices. There is a growing interest in the mining industry to model and manage such market uncertainty in the pit optimization as well as the project evaluations in order to maximize the value of mining operations. In this paper, the author will outline a practical approach to optimize the ultimate pit taking into account the volatility and variability of metal markets. The proposed approach uses a combination of the pit optimizer of the commercial MineSight package and a simulation-based economic modeling real options valuation approach employing the least-squares Monte Carlo algorithm. MineSight pit optimizer employs both the floating cone for initial optimization exercise and the standard Lerchs-Grossmann algorithm. In this paper, Lerchs-Grossmann option will be used to generate the pit shells. Real options valuation approach used in this study is based on generating multiple metal price scenarios. Metal price uncertainty is modeled using stochastic metal price models such as the geometric Brownian motion and the mean-reverting process. The mining operational scenarios corresponding to the simulated metal prices are then optimized using the least-square Monte Carlo approach. The objective is to maximize the discounted cash flow value of the project while incorporating the operating flexibility to revise the operating status of the open pit with time as new information becomes available. The focus of this work is on the practicality of the proposed uncertainty-based pit optimization approach and the difference it can make to the technical operational mining decisions. A case study of a hypothetical open pit poly-metallic mine is provided. The deposit contains copper, gold and silver grades. The run of mine ore is sent to the process plant that produces copper concentrate with copper as the main metal and gold and silver as the by-products. Four uncertain variables are considered here include copper, gold, silver prices and foreign exchange rate. Both copper price and exchange rate are modeled using the mean-reverting process while gold and silver prices are modeled using the geometric Brownian motion. The case study is performed using both the conventional flat price pit optimization approach and the proposed uncertainty-based one to compare results.

Aug 1, 2013

By C. A. Ingram

The Cigar Lake ore body is a high-grade uranium deposit situated within water-saturated sandstone. In order to extract the uranium ore remotely, ensuring minimal radiation dose to workers, and also to access the ore from stable ground, the Jet Boring System (JBS) was developed. This method of mining involves drilling a pilot hole up through a frozen ore body and utilizing a high-powered water jet to mine out cavities. During the mining process an ultrasonic sensor will be used to provide feedback to the operator, who is located beneath the ore body, as to the dimensions of the cavity. However, more precise data is required to determine final shape, volume, and location of the cavity for mine planning purposes. Selecting a device that will provide sufficient range data in the challenging environment will be vital to optimizing the mining process. Major issues include fog build up and flying debris during mining, and an environment that is wet, dark, and cold A test cavity has been designed and constructed at the Saskatchewan Research Council (SRC) so that a study comparing three different technologies, as prospective candidates for the survey system, can be conducted. The devices being evaluated include a Senix ultrasonic sensor, an MDL Cavity Auto-Scanning Laser System (C-ALS), and a MESA Time of Flight (ToF) camera. The ultrasonic sensor is known to provide range data in foggy conditions but has low accuracy. The C-ALS has been developed for surveying remote cavities but is expensive and does not provide reliable data in fog. The ToF camera provides a high volume of data in a short time period, with potential to provide accurate information in extreme conditions, but has not been tested in a mine cavity application. Iterative closest point (ICP) registration is applied in an attempt to create a 3D point cloud from the scan data and to also compute rotation and translation of the ToF camera. This paper presents an overview of the challenges involved in conducting a survey within a JBS mined cavity, the analysis used to determine the suitability of each device, and the data collected from the test cavity.

Aug 1, 2013

By G. Van Weert

ABSTRACT When exposed to microwaves, rocks containing sulphides adsorb energy preferentially over barren gangue and quickly become warmer with minimal energy consumption. This effect makes subsequent machine sorting of ore from waste rocks or overburden possible using infrared sensing. This paper reports on the 2450 MHz microwave response of a variety of sulphide minerals by mesh size and spatial distribution, as they might occur in ore rocks. The implications for infrared ore sorting are discussed.

Aug 1, 2011

By D H. Sharp

The Quebec Cartier Mining Company produces iron concentrate for twelve months of the year from Port Cartier. This J>Ort is designed to handle ship varying in size from 3,000 to 100,000 d.w.t., requiring 50 feet of water at low tide. The harbour was built on shore for reasons of economy and layout, after considering many more conventional offshore designs. It provides for heavy oil bunkering, tanker off-loading, a heavy lift derrick and freight handling, besides ship loading and mooring. The weather for the previous fifty years was studied to enable wind and wave conditions to be accurately assessed for design purposes, and to determine probable lost time due to adverse weather conditions through-out the year. The first ship to be loaded was 60,000 d.w.t.; the second, 20,000 d.w.t. The latter entered the harbour after dark, under its own power, following a tug through the partly dredged narrow entrance. Large ships use tug assistance. Ships may leave the loading berth with the other berths occupied.

Jan 1, 1963

By G. N. Carlson, C. H. Hazelroth, D. R. Dorrance

"Located on the north shore of the St. Lawrence River at Pointe Noire, Quebec are the agglomeration and ship-ping facilities of the Wabush Mines complex. Here, the specular hematite concentrate from the Scully Mine is received for further processing. Modern facilities for handling the ore, either to the 1plant or to stockpile, provide quick and efficient operation of the ore receiving station. Physical preparation of the ore for balling is accomplished with regrind ball mills, filters, bentonite crushing and drying facilities, pumps and related conveying circuits. Rotating table feeders deliver the reground and de-watered ore from storage bins to balling drums, where green ball or green pellet formation is achieved. The green balls are then conveyed to the indurating section. Three Dravo-Lurgi travelling grates, producing a total of 6,000,000 long dry tons of pellets per year, are used in the indurating phase of the operation. These grates, having 38 windboxes and firing at a temperature of 2,500°F, harden the pellets for shipment to various blast furnaces throughout the world."

Jan 1, 1969

Building off the enthusiasm generated by Credit Suisse First Boston on the potential benefits of an industry-wide effort to market gold jewellery, a group of gold producers, led by Randall Oliphant, CEO of Barrick Gold, decides to investigate the long -term impact of launching a significant marketing initiative to stimulate demand for gold jewellery. The group establishes an international Steering Committee representing producers of differing sizes, members and non-members of the World Gold Council. This Committee comprises representatives from AngloGold, Barrick, Gympie Gold, Kinross, Randgold, and Sons of Gwalia and is supported by the Australian Gold Council, the Gold and Silver Institute, and CSFB. The Steering Committee hires McKinsey to assist it by conducting an independent review of whether investment in a large-scale marketing initiative for gold jewellery would be effective in increasing demand for gold, and ultimately of significant economic benefit of the gold industry. Based on McKinsey?s review* and its own discussions with key stakeholders across the industry, the Steering Committee strongly believes the case for marketing is compelling and sufficiently proven to persuade the industry to undertake a major initiative over the next few years. The Steering Committee, supported by McKinsey, conducts briefings with a range of gold producers to share its findings and to understand producers? perspectives on an industry-funded marketing campaign. The Steering Committee is asking for your support to bring this industry-funded marketing campaign to life.

May 1, 2002

By D. Rylander

The operation of Quarry and Aggregate sites are similar to factory production, since it contains sequential production processes, tasks and activities to produce the output product. Compared to the plant though, the quarry processes are generally not synchronized and controlled towards the overall throughput of the site in real time. Some quarries control parts of the production but do generally not utilize real-time technologies for the whole site and all its activities. This fact indicates a general improvement potential in increased productivity at quarry sites, but also unsolved challenges for the same reason. The main contribution of this paper is the presentation of a Lean based method for how to describe the processes to identify control improvement potential within a site. The aim of the identified improvements is to increase overall site productivity by optimizing site, fleet and machine utilization towards the overall throughput, and minimizing operational expenses and inventories. Further the paper exemplifies the method?s usability with field studies at operational quarry plants successfully identifying and quantifying potential wastes and improvements. In addition the identified productivity improvements based on increased control and automation indicate challenges and needs in wireless communication and sensing technologies.

Aug 1, 2013

By Darren Medd

Kumtor Gold Company (KGC) currently operates the 500,000 tonnes per day Kumtor open pit gold mine located in the Issyk-Kul region of the Kyrgyz Republic at an elevation of more than 4,000 m. To supplement the open-pit mill feed with high grade underground ore from outside the current pit limits, KGC started pre-production design and development of the underground mine for the SB ore zone in late 2006. The initial phase of pre-production development consists of exploration and haulage declines which, upon completion, will provide ventilation and access to the underground mine. Design and construction of these declines presented many challenges to the project team considering the mines unique location at high altitude, the limited experience with Western underground mining techniques in the Kyrgyz Republic, and the impact of the nearby Davydov glacier and resultant ground conditions. Completion of the exploration and haulage declines was undertaken jointly by KGC and mine contractor, J.S. Redpath Limited (Redpath). The initial phase of development including several ground falls provided detailed information on geotechnical ground types and conditions that were useful in determining the overall mine design and methodology for production. This paper covers the various aspects of the design and construction process of developing the declines under the glacier, minimizing the likelihood of further ground falls, and the journey of both KGC and Redpath which led to the successful breakthrough between the declines on 01 July 2012.

Aug 1, 2013

By K. Scholey, S. Marcuson

As high grade nickel sulphide ores are being depleted and with the continuing challenges experienced in economically processing nickel laterite ores, it is important to investigate technologies that can extract nickel from low grade ultramafic ores which are present in large quantities worldwide. In the Thompson Nickel Belt, there are some hundred million tonnes of mineralization that are potentially amenable to surface mining. Since the original discovery of the Thompson orebody, recovery of nickel from these ultramafic deposits has been an elusive goal. Research and development projects as well as commercial processing have been attempted. In the 2000's as other resources became scarcer, a major drilling, mine evaluation and research project was initiated at Vale. In 2007, Vale Base Metals Technology Development invited Cytec and potential academic partners to participate in an industry-university research consortium with the goal of developing new technologies and methods of processing the ultramafic deposits. Three university professors, J. Finch of McGill, P. Somasundaran of Columbia and R. Pelton of McMaster accepted, each group attacking the problem with a different approach. This paper describes the management of the research consortium and the significance of the results from Vale's perspective. The next four papers in this session will summarize the project and results from the partners' point of view. Vale is pleased to share the experience of the collaborative research and development with the mining industry.

Jan 1, 2011

By P. C. Benedict

"The Island Mountain mine is at the southeast end of Island mountain; across Jack of Clubs lake from the Cariboo Gold Quartz mine.; The orebodies consist of quartz veins and pyritic replacement deposits in limestone. To December 31; 1944; there has been mined 296; 273 tons of quartz-vein ore averaging about 0.34 oz. gold a ton; and 101; 002 tons of sulphide ore averaging about 0.83 oz. gold a ton; a total of 397; 275 tons averaging 0.46 oz. From this; 175; 985 fine oz. of gold and about 26; 450 fine oz. of silver were recovered; having a value of $6; 510; 521.More than 95 per cent of the production has come from a band 500 feet wide along the contact of the Rainbow and overlying Baker members and extending about 100 feet into the latter. Evidence that the Rainbow belongs stratigraphically above the Baker is presented later in this paper. Both members are most variable lithologically, and individual beds and whole series of beds pinch out in short distances. In part, at least, this is due to squeezing out incidentally to intense folding. No section can be claimed with assurance to be really representative. However, both memb.ers are composed predominantly of quartzitic rocks. Both contain argillaceous quartzite, argillite, limy quartzite, limy argillite, limestone (marble), and minor amounts of highly ankeritized rocks believed to be igneous sills possibly originally approaching diorite in composition."

Jan 1, 1954

By John M. Gordon

DURING and after 1949, various groups of British mining engineers came to the Dominion Coal Company, Limited, at Sydney, N .S., to see at first hand the Dosco MINER ( 1). These visits culminated in 1952 with the ordering of four Dosco Miners by the (British) National Coal Board on an experimental basis through their Experimental Expenditure Funds. Others are now on order. The first machine was delivered in February, 1953, and, after slight alterations to suit the different power supply, the machine was made ready to work. Due mainly to the size of the machine, new rules and regulations governing its operation had to be put into effect and it was not until April, 1954, that the machine was put underground. It started to produce in June of that year. The three others were delivered early in 1955. The authors were sent to England by the Dominion Coal Company to install and demonstrate these machines and to work with the Coal Board engineers to- further interest in the machines in the British coal fields .

Jan 1, 1956

By P. N. Calder, D. B. Apel, S. D. Butt

Mine-wide (MW) microseismic systems use widely spaced transducers to determine the source location and parameters of stronger microseismic events, while high frequency (HF) systems use fewer transducers to monitor local areas for the weaker events that can precede stronger events. Previous monitoring at the Creighton Mine indicated that an HF transducer located 120 m away from an active stope recorded two types of activity in response to production blasting: the first occurring at the same time as the production blasts and associated with the passage of the direct seismic waves from the blast through the local area, and the second occurring several hours later and associated with the arrival of a slower moving stress change through the rock mass (which was identified by the mine’s MW system). Interpretations of locally increased stress levels, based on analysis of the recorded HF events, correlated with the nearby occurrence of two strong seismic events. These results were applied to a similar monitoring trail at the Kidd Creek Mine where the transient stress changes induced by several development blasts were monitored. It was observed that increases in HF activity corresponded with the occurrence of MW events near the transducer location, and that fewer HF events were recorded the longer this occurred after the blast. Local geological features appeared to influence the number and occurrence of both HF and MW events.

Jan 1, 2000