Search Documents

By R. B. McIntosh, S Ramanchuk

A brief description is given of the process used by Sherritt Gordon Mines Limited to recover cobalt metal from nickel-cobalt sulphides. A description of the equipment with the operating conditions is presented with an evaluation of the corrosion test results for various stainless steels and other acid resistant materials for the part of the process involving the sulphuric acid leaching of nickel-cobalt sulphide slurry under air pressure. SINCE 1954 the Sherritt Gordon ammonia leach process has been used at Fort Saskatchewan to recover nickel metal, copper sulphides and cobalt-nickel sulphides from nickel concentrate produced at Lynn Lake, Manitoba. 'To develop a process for recovering cobalt and nickel from the cobalt-nickel sulphides, studies were carried out in the Sherritt Gordon laboratory and pilot plant and, late in 1957, continuous acid leaching of sulphides was started in the refinery. In September 1958 the present equipment

Jan 1, 1961

By S. Fabich

Since the very beginning of Polish copper mining, special consideration of sink shaft techniques through highly saturated Cenozoic rocks was required. Shaft freezing has been chosen as a method to consolidate these rocks. Due to the rock mass structure and water inflow potential, shaft sinking without freezing was considered dangerous. In the course of time, rock mass freezing technology and experience were evolved and this technology became safer and more reliable. New techniques appeared not only in the technical method of freezing, but also in the matter of designing. Computer aided techniques allow engineers to make a detailed analysis and view of freeze wall development. Nevertheless it is important to determine basic thermal rock properties. In this paper, the evolution of knowledge and engineering experience taken in Polish copper mines and current knowledge level in that matter were shown.

Aug 1, 2013

By Forrest A. Kerr

Introduction During recent years the work of the Geological Survey in northwestern British Columbia has been in the nature of reconnaissance and exploratory mapping, largely for the purpose of gaining knowledge of the potential mineral-producing zones known to occur along the eastern side of the Coast range, and also to gather such data as might facilitate their exploitation. Commencing with fairly detailed mapping in the more accessible parts, the work has been continued and expanded until now an understanding has been gained of the more general features of a continuous section along the range for a distance of about two hundred miles. Geographically, northern British Columbia is more or less isolated. It is cut off from the central part of the Province by a rugged and mountainous country which, except for the telegraph line and a rarely travelled trail along it, is not penetrated by any developed routes or lines of communication. To the west, it is cut off from the Pacific by the Coast range, an extremely rugged area sixty to eighty miles in width which, except along the few navigable rivers cutting across it, cannot be readily traversed. Politically, it is further isolated in this direction by the narrow strip of south-eastern Alaska which borders the coast and extends inland to the axis of the range.

Jan 1, 1931

By W. E. Halle, G. J. S. Govett

"The Institute of Applied Geology, Manila, Philippines, is jointly sponsored by the University of the Philippines, the Philippines Bureau of Mines and the United Nations Development Programme (Special Fund). It provides, in its fourth year of operation, an interesting example of international cooperation in mineral development. Objectives include: (1) the training of mining engineers in modern techniques of mineral exploration; (2) assisting government and industry in discovering new ore deposits; and (3) providing the basis for the establishment of an economically oriented graduate school of geology at the University, the first of its kind in the country. Training of engineers requires roughly one full year, which is divided between academic study and actual field practice. Lecture and laboratory instruction include courses at university level designed specifically to up-grade those aspects of the geological sciences that are required by mining engineers now qualifying as mineral exploration engineers-economic geology, applied geochemistry, geo-physical exploration, petrology and structural geology. The field training involves direct participation in actual mineral exploration projects arranged with the co-operation of the Bureau of Mines and private interests engaged in mineral development and production. The system works well in practice, and the Institute staff and trainees were responsible for outlining new evidence of economic mineralization. It is also apparent from the application of the exploration methods available to the project -geological mapping, air photo interpretation, magnetic, electric, electromagnetic, self potential and gravity surveying as well as geochemical prospecting -that, under the humid, tropical, mountainous conditions in which the practical program was conducted, air-supported geochemical prospecting with attendant reconnaissance geological mapping affords the most economical and effective approach to mineral exploration for at least some of the deposits characteristic of the region."

Jan 1, 1968

By H. H. Gardner

INTRODUCTION THE problem of mechanization is one of the most vital in the minds of Alberta coal operators today. In these times of constantly increasing operating costs, any way of decreasing the cost of a ton of coal must be explored to the limit. There seems no better field for such effort than the successful application of power to the mining and loading of coal. We are fortunate in having neighbours to the south who have made .remarkable progress in recent times along these lines. Higher tonnages per man have resulted in higher wages to the employee and lower cost to the employer. It might seem that our problems could be solved merely by imitating our neighbours. Unfortunately, neither practice nor experience substantiate this conclusion. It is with the purpose of reviewing our accomplishments, as compared with practice in the United States, and at the request of the Prgoramme Committee for this meeting, that this paper is written. The Committee believes that such a general discussion and comparison may well lead to further advances in our mining methods. SUMMARY OF PRACTICE IN THE UNITED STATES A visit to the highly mechanized coal mines of the United States is always most instructive and encouraging.

Jan 1, 1951

By A. Desbiens, A. Pomerleau

During the summer of 1994, a new PID-based control strategy was installed on line B of the grinding circuit at the Kidd Creek Division of Falconbridge Ltd. Part I of this paper described the methodology used to select the appropriate control strategy using a phenomenological dynamic simulator. Part II presents the implementation of the control strategy. Prior to the controller installation, it was necessary to solve various problems related to the process, such as a cyclic behaviour of the rod mill feed tonnage, a problem related to the mill water source and the calibration of the flowmeters. Once these problems were solved, the control strategy was accomplished in two steps. Step 1 corresponds to the installation of control loops to regulate the pump box level and the cyclone overflow density. Step 2 describes the implementation of a loop to control the cyclone feed density. According to Part I, a loop to control the circulating load is also part of the original design. However, reasons are given to explain the rejection of this loop. For both steps, technical procedures such as filtering, process identification and controller tuning are detailed. Finally, the operator’s interface is briefly described.

Jan 1, 1997

By D. F. Machuca-Mory

The new algorithm for high-order simulation of ore deposit grades termed HOSIM is based on the concept of spatial cumulants. The algorithm is tested using data from Apensu, a structurally controlled gold deposit in Ghana. The required high-order spatial structures are obtained from a training image or analogue of the deposit. Using the available drillhole data and training image, HOSIM realizations are able to model well the grades and geometry of the large and well sampled mineralized structures. However, under-sampled small structures remain difficult to model. HOSIM offers a promising alternative for the spatial simulation of complex non-Gaussian orebody attributes of interest.

Jan 1, 2011

By B. R. Richards, B. G. W. Robinson

"This paper shows how metal values can be profitably won from a comparatively small and remotely located but high-grade orebody. To do so is not uractical for a large mining company, with its necessarily high overhead of services and organization essential to a large producer.To evaluate, develop and profitably exploit a limited but defined ore deposit becomes only a problem of determining the dollars required to win the dollars available. This paper will record how this was carried out during 1965 and at the same time describe the history, development and production plant of this property."

Jan 1, 1966

By X. Shi

Magnesium, the lightest structural metal, has not yet been considered as a serious contestant for automotive use due to its weaknesses in corrosion. Electroless nickel-boron alloys are well known for their corrosion resistance and hardness. An electroless nickel-boron layer was successfully deposited first on the chemical conversion pre-treated AZ31 alloy and also on the Ni-P coating which was deposited on the conversion coating. The electroless bath contained nickel sulphate and dimethylamine borane (DMAB) as main salts and the samples were activated by a 5 g/L AgNO3 solution before the electroless plating process. The presence of the conversion coating between the nickel coating and the AZ31 substrate acted as a barrier and prevented corrosion of the alloy. The morphology of the nickel-boron layer was studied using SEM. The crystal structure and the composition were examined by EDS and the hardness was measured. The corrosion behaviour of the nickel-boron layer deposited on the conversion coating and on the Ni-P coating was studied using potentiodynamic polarization in a 0.5M NaC1 solution. A saturated standard calomel electrode was used as a reference electrode. The results show that the nickel-boron coatings had a significantly better corrosion resistance than the AZ31.

Jan 1, 2006

The Red Lake greenstone belt is an irregular mass of lavas sedimentary rocks and intrusives which is approxiately 35 miles long 18 miles wide and 7 miles deep. Basaltic volcamcs are the oldest rocks w1thm the belt. They are believed to have been laid down on an ancient crust which is at least 3 billion (3 x 109) years old and was composed partly of sediments. The basaltic rocks are overlain by acid volcanics and sedimentary rocks which have been complexly folded and are preserved as a down-folded remnant of younger rocks within the older crust. The volcanics and sedimentary rocks of the greenstone belt have been cut by intrusives with a wide range of composition. The emplacement of the intrusives and the accompanying regional metamorph-ism which terminated the orogenic activity in this area are believed to have occurred approximately 2.4 billion years ago. The basalts and many of the basic and ultrabasic intrusives undoubtedly had their source in the sub-crust or mantle. At least some of the granitic intrusives are believed to have had

Jan 1, 1965

By G. Song

Magnesium has excellent bio-compatibility in terms of its density, strength, elastic modulus and toxicity. However, due to its poor corrosion performance, so far magnesium has not been successfully used in the human body as a permanent implant material. Nevertheless, there is a possibility to utilize the low corrosion resistance of magnesium to make magnesium into a temporary implant component that can gradually dissolve in the human body after surgical region heals. This will avoid the secondary operation to remove the temporarily implanted component and the chronic inflammatory discomfort caused by the implant. This paper is aimed at exploring the possibility of using magnesium as a degradable bio-material through investigating the corrosion behaviors of pure magnesium and surface treated magnesium in a simulated body fluid (SBF) solution. It was found that magnesium corroded rapidly in the SBF solution, resulting in vigorous hydrogen evolution and a strong alkalization effect. Hence, it is impractical to use magnesium as a permanent implanted material or even a degradable implant. However, a proper anodizing treatment can significantly improve the corrosion resistance of magnesium, and hence slower down the hydrogen evolution and alkalization processes, which will allow to control the corrosion or degradation of magnesium at a desired rate in the human body. With a controllable corrosion rate, it is believed that magnesium as a degradable implanted material will be eventually achievable.

Jan 1, 2006

By Stopford Brunton

For many years it has been accepted as axiomatic that the greater number of 'veins' or 'leads' in the gold districts of Nova Scotia are of the 'interbedded' type. The corollary to this hypothesis is that the vein or lead will have a continuous hanging-wall of one kind of rock, and a continuous footwall of the same or another kind of rock; but the essential point is that the foot and hanging walls are, according to this theory, both continuous and of uniform composition throughout; and that the vein or lead conforms to the bedding of the adjacent strata. With regard to the deposition of the gold in the rocks, the probability is that the key of the problem is contained in a statement by E. R. Faribault, of the Geological Survey of Canada: "The combined effect of cleavage, jointing, and stratification is to cause the rocks, especially the quartzites, to break into rhombohedral blocks". It is essential to comprehend that the rocks of the Province are no doubt folded into anticlines and synclines; but also it must be fully realized that the gold deposits and pay-shoots do not depend so much upon these as upon the fractures resulting from the disturbance caused by the intrusion of granite masses, and controlled by the combined effect of cleavage, jointing, and stratification. These fractures would form the channels through which the ore-bearing vapours and solutions would rise, and at the junctions of these fractures, where the fracturing was greatest, the easiest passages would be afforded to the ore carriers, with the result that the ore-shoots would be found at or near the intersections of fractures. It is a significant fact that in at least thirteen different districts throughout the Province, operators have at various times remarked upon the occurrence of rich ore at the intersection of 'leads,' 'veins,' 'beds,' etc.

Jan 1, 1928

By Andrew Dobson, Cheryl Allen, Enrique Acuña

"Totten Mine return air raise was designed with two parallel fans equipped with silencers to reduce the noise emitted from the outlets into the environment. As development and production of the mine progressed through the past years, the silencer system needed to be upgraded, and additional maintenance strategies have been necessary to meet the regulatory noise limits enforced by the province of Ontario. The current mine plan will require the fans to reach the upper limit of their capacity by Q1 2019. To achieve this operational target, additional silencing capability has been required and Totten Mine has explored alternatives to further extend the noise silencing capacity available considering the current constraints at the mine site. The alternatives included a new silencer baffle design and a new layout that have allowed doubling the length of the silencer system. Using acoustic measurement data collected on several occasions, this paper presents and discusses the performance of the various silencing systems which have been installed on the return air fans at Totten Mine.INTRODUCTION Vale Canada Limited’s Totten Mine is a base metal, underground mine extracting nickel and copper, situated in the Sudbury Basin of Ontario. The mine initiated operations at the end of 2013, and is equipped with two main return air fans and two main fresh air fans located on surface. Both fresh air and return air fans are set in a parallel arrangement to operate as integrated units and are equipped with variable frequency drives (VFDs) to allow for the remote modification of their operating set point, usually between 600 to 880 rpm, depending on the mine’s requirements. The main return air raise (RAR) fans are also equipped with dissipative baffle silencers to attenuate the noise emitted to the environment. Approximately four years ago, acoustical measurements conducted to verify compliance with the applicable regulatory criteria, and respond to noise concerns from neighboring residents, concluded that the sound emissions of the main return air raise exceeded the noise design parameters. The acoustic tones of the fans were audible offsite, at a residential location, approximately 9 km northeast of the mine site. The elevated sound levels and offsite audibility was due to degradation of the original discharge silencers from moisture and particulate being drawn from underground workings and passing through the silencer baffles. The audibility was also due to an outlet directivity pattern which directed noise towards the residential location."

Jan 1, 2019

By Michael Moats, Adirek Janwong

The use of cylinder electrowinning cells, such as emew® technology, for the recovery of silver from primary and secondary sources has been growing. In this study, common operating parameters used in silver electrowinning were evaluated for recycling applications. Silver powders were produced from an industrial solution in a laboratory scale emew® cell. A design of experiments was employed to evaluate the effects of HNO3 concentration, iron concentration, current density and solution flow rate on current efficiency, particle size, bulk density, and crystallographic orientation. Current efficiency was affected by each parameter with increasing HNO3 concentration having a strong negative effect, increasing iron concentration and current density having moderate negative effects and increasing flow rate having a positive effect over the ranges examined. Finer particles were produced with increasing current density and decreasing flow rate. Bulk density increased when HNO3 concentration increased. The crystallographic orientation of all powders was dominated by the (111) plane. Increasing flow rate decreased the relative intensity of (200) direction. Based on these observations, silver electrowinning in cylindrical cells can operate at high current efficiency and produce larger powders at low HNO3 concentration, low iron concentration, low current density and high flow rate.

Jan 1, 2014

By J. L. Thornton

Introduction The importance of coal in our economy is well established, but it may not .be so generally realized how important a part it plays in our daily life. Select a product - any product - and, if it is made in America, bituminous coal has touched it first. Everywhere we will find coal, derivatives of coal, or functions made possible by coal. Apart from the well known major uses of coal for domestic purposes, coking, utilities, railways, and manufacture of steel and cement, there are over 200,000 products derived from coal, from lipstick colours to nylon products and perfumes. An item of interest is the recent action of the Canadian Government in voting $90,000 for development of coal deposits in Yukon Territory to make coal available to the settlers in that area. The value of this move, in case of some emergency, is very evident. Coal in its several stages of formation as peat, lignite, sub-bituminous, bituminous, semi-bituminous, semi-anthracite, and anthracite, has been used for centuries. Coal, as such, was not very well known to the ancients. First reference to "magic stone', or coal, was in 371 BC by Theophrastus, a pupil of Aristotle. This substance was said to burn like wood coal or charcoal and was used by the smiths. The first record we have in modern times was in 852 AD, when sea coal was gathered by the cowled monks of Durham, in Britain, and even at that time a major problem was transportation. Our first record of coal in this continent was near Richmond, Virginia, in 1700. Commercial mining was not under way, however, until 1750. The anthracite fields (presumably in Pennsylvania) were opened in 1793. Even so, there was no extensive mining until about the year 1820. The famous Pocahontas coalfields were opened in 1883. The earliest record of coal mining in Canada is about 1746.

Jan 1, 1950

By P. Kobylin, K. Haavanlammi, K. Valkama

"Base metals and precious metals can be recovered from a nickel matte or nickel concentrate using the Outotec nickel chloride leaching process. The raw material is leached with hydrochloric acid and the metals are recovered by solvent extraction, where ammonia is used to control the pH. Ammonium chloride is regenerated to ammonia and the side product of this step is calcium chloride solution. The regeneration utilizes either calcium oxide or calcium hydroxide. The calcium chloride solution is used to convert sulfuric acid into a hydrochloric acid solution while producing pure gypsum as a side product. The regeneration and reuse of ammonia and hydrochloric acid in this process will have a positive impact, from the point of view of both operating costs and environmental sustainability. This paper concentrates on the test work and technical concept development performed by Outotec to implement and develop chemical regeneration and recycling into a vital part of the nickel chloride leaching process.INTRODUCTION According to a nickel market analysis, the nickel market is expected to grow in the future. Main driver for this growth is the increase in stainless steel consumption as the living standards are equalizing globally. The expected increase in the amount of electrical cars and the need for nickel in the batteries of electrical cars also gives potential for the increased need for nickel in near future. At the moment the use of nickel in nickel-cobalt-manganese (NCM) and nickel-cobalt-aluminium (NCA) Li-ion batteries is in the range of 14 ktpa. It is estimated to increase to the level of 90 ktpa by 2025. In every era of the nickel industry, Outotec has been constantly developing new processes to create environmentally sustainable and economically viable processing routes. The Outotec® Nickel Matte Chloride Leaching process is a great example of a process that is flexible regarding raw material and could also treat nickel raw materials that are difficult for smelters. Outotec’s main options for pyrometallurgical nickel treatment include the Outotec® Direct Nickel Flash Smelting process (DON) and the Outotec® Ausmelt TSL process. The DON process is operated in Boliden Harjavalta Nickel Smelter in Finland. Ausmelt process is in use for example in Daye nonferrous plant in China. In the Outotec® Direct Nickel Flash Smelting Process, a sulphide nickel concentrate is processed in an Outotec Flash Smelting Furnace (FSF). Producing concentrates and processing them by Outotec Direct Nickel Flash Smelting to matte followed by hydrometallurgical refining offers a reliable route from concentrate to product. In the DON process, high-grade matte with low Fe content is produced in the FSF and the valuable metals in the slag are recovered in an electric furnace (EF). The Outotec® Ausmelt TSL process can use a large variety of raw materials (concentrates, secondary material and scrap metal) as feed. Fuel and oxygen are injected into the furnace through TSL (Top Submerged Lance) and this enables efficient smelting. Both Flash Smelting and TSL plants produce nickel mattes, which can be refined with Outotec hydrometallurgical processes."

Jan 1, 2017

By A. J. Naldrett

"Sulphurization of peridotite, that is 'to say reaction between sulphur from an external source and iron and nickel in the silicate minerals of the peridotite or in partially consolidated magma, is believed to be the me-chanism by which the small iron-nickel sulphide deposits associated with the ultrabasic rocks of the Porcupine district have formed.The pyrrhotite-pentlandite ore at the Alexo mine, Dundonald township, is localized by a shear that closely follows the lower contact of a peridotite lens. In the past, to account for this orebody, the magmatic segregation hypothesis has been advanced on the basis of textural evidence and the presence of the sulphides at the base of the lens. The nickel sulphide de-posits of the Porcupine, however, are not characteristically found along the basal contacts of bodies of peridotite. Furthermore, this study has shown that textures formerly thought indicative of magmatic segregation have been formed in certain deposits by the selective replacement of silicates by sulphides.At the Alexo mine, very minor amounts of pentlandite and heazle-woodite (Ni3S2) occur in the peridot-ite hanging wall adjacent to the ore. These sulphides are interpreted as having formed by sulphurization, the sulphur involved coming from the pyrrhotite-pentla.ndite ore emplaced along the shear. This reaction aureole raises the question of the role of sulphurization in the formation of the main mass of the sulphide ore. The very localized equilibrium that has been found to exist between sulphides and silicates in deposits throughout the area, the results of nineteen sulphur isotope determinations, and the abundance of pyrite and pyrrhotite in the volcanic country rocks of the Porcupine indicate that these deposits were formed by sulphurization rather than magmatic segregation."

Jan 1, 1966

By M. W. Bates, A. L. Mular

This paper, based on work carried out at Queen's University, describes the development and use of mathematical models of the parallel cyclone classifiers being used in the Strathcona mill of Falconbridge Nickel Min.es Ltd.

Jan 1, 1971

By V. Vakiloroaya

The paper aims at developing a hybrid solar-assisted air conditioner system for performance enhancement and energy efficiency improvement. To increase sub-cooling of the refrigerant at partial loads, we propose a new discharge bypass line together with an inline solenoid valve, installed after the compressor to regulate the mass flow rate of the refrigerant vapour passing through a hot water storage tank. For control design, a lumped parameter model is first developed to describe the dynamics of the system in an explicit form of input-output relationship. The system has been fully-instrumented to examine its performance under different operation conditions. The system model is then validated by extensive experimental tests. The predictions from the models exhibit a good coincidence with experimental results, judging by an RMS error less than 15%. Based on the obtained dynamic model, a linear quadratic regulator (LQR) is applied to optimize a cost function of the output errors and control efforts. The key challenge is to regulate the refrigerant temperature entering the condenser by controlling the valve opening. The design approach is then tested in a transient simulation tool to predict the system performance in transient conditions. The experimental results obtained from implementation with PLC demonstrate that the proposed system delivers higher system efficiency owing to the higher refrigeration effect in the direct expansion evaporator. Thus, the novel development is promising for improvement of energy efficiency, enhancement of the system performance while fulfilling the cooling demand. Consequently, between 25 and 43% of monthly electricity can be saved on average.

Aug 1, 2013

By L. Frost

"Since the late 1990s, increased prevalence of severe lung disease among US coal miners has been observed, particularly in central Appalachia where thin-seam mining is prevalent. While respirable silica exposures have been implicated in many cases, the available dust monitoring data from mines shows no explanatory trends. One possible factor could be differences in the relative toxicity of silica particles based on their surface condition. Previous research has indicated that particles with occluded surfaces (e.g., by a thin layer of clay) may be less toxic than those with non-occluded surfaces. However, this dust characteristic has not been investigated before now in central Appalachian mines. In the present study, 18 respirable dust samples from seven central Appalachian mines and two northern Appalachian mines were analyzed to assess the relative occurrence of surface-occluded silica. Results showed that the dust from central Appalachian mines actually had higher fractions of occluded silica, which may be due to extraction of large amounts of rock strata along with the coal. However, the central Appalachian mines also more silica particles overall (i.e., occluded + non-occluded) in terms of total number percentage of respirable particles.INTRODUCTIONResurgence of occupational lung disease among US coal miners, especially in the central Appalachian region, has been observed since the late 1990’s (Gibson, 2016; Zosky et al., 2016; Suarthana et al., 2011; Gamble et al., 2011; Antao et al., 2005; Attfield & Sexias, 1995). In addition to increased prevalence of simple Coal Workers’ Pneumoconiosis (CWP, or “black lung”), the prevalence of severe and rapidly progressive disease has risen dramatically (Almberg et al., 2018; Blackley et al., 2018a, 2018b, 2016, 2014; Graber et al., 2017; Cohen et al., 2016). While exposures to respirable silica have long been known to cause or play a role in diseases such as silicosis or progressive massive fibrosis (PMF), which is conventionally considered as the most advanced form of CWP, it is unclear whether silica is the only culprit in the recent outbreak of severe disease. Indeed, as disease rates have risen, both total respirable dust and silica concentrations generally appear to have declined since the late 1980s, based on regulatory monitoring data in the most affected mining districts (i.e., MSHA coal Districts 4, 5 and 12, which cover central WV, eastern KY and southwestern VA, and southern WV, respectively) (Figure 1). Of course, the latency of disease can vary and may be or more 10 years, but many of the most recent cases are likely to have resulted from exposures that occurred since the late 1980s."

Jan 1, 2019