Search Documents

By R. W. Davis

INTRODUCTION CHURCHILL river was named for John Churchill, first Duke of Marl-borough and third Governor of the Hudson's Bay Company, in the latter part of the 17th century, some fifty years after the ill-fated Danish expedition, led by Munck, had abandoned the site of the now famous seaport of Churchill, as a worthless, cold, disease-ridden country. No other attempts were made to explore the interior until the river basin became a part of the grant to the Hudson's Bay Company and began to play its part in furnishing the luxury of fine furs to civilized people as it had furnished the necessities of food and dress for untold centuries to uncivilized natives. This was the sole contribution of the region to the economic life of the country for some two hundred and fifty years, until 1926, when the power site at Island Falls was discovered by engineers seeking a cheap power source to make possible the development of the great ore-body at Flin Flon. DRAINAGE BASIN OF CHURCHILL RIVER The river is some 1,325 miles long. Rising in the headwaters of the Beaver river, in east-central Alberta, it flows in an easterly direction across Saskatchewan and northeasterly across Manitoba to Hudson bay, through a remarkable basin of some 115,500 square miles, only 6,000 square miles less than the area of the British Isles. A journey down this river leads one through three distinct belts of country, each vastly different from the others geologically and in surface characteristics. For the first five hundred miles the river flows through a basin of 36,000 square miles of the great central-plains country, which is covered with fertile soil and carpeted in its southern part with prairie grass, which gradually gives way to the mixed forests of poplar, spruce, birch, and jackpine in the northern and eastern sections: About midway across Saskatchewan, bald-headed knolls and ridges begin to make their appearance as the river meets the western margin of the Canadian Shield. Then, for some seven hundred miles, it passes through country underlain by the pre-Cambrian rocks of the Shield, which continue to within one hundred miles of Hudson bay. Here the character of the country again changes to a low, clay plain underlain by sandstone, and through this 'clay belt' the river flows between steep clay banks, to empty into Hudson bay.

Jan 1, 1935

By Gordon R. Harris, Raymond Chalk

Descriptions of typical pulp and paper manufacturing processes are presented, with particular emphasis on the use of minerals and derived products. Some consideration is given to the future demand for these minerals by the pulp and paper industry. Possible influences of techno-logical change and social legislation are suggested and their effect on saltcake demand by the pulp industry is discussed. Predictions are made regarding trends for new and existing paper products.

Jan 1, 1968

By T. H. Janes

THE POSSIBILITY of producing pig iron from iron ores of British Columbia for a west coast primary iron and steel industry has been investigated by the provincial government and by commercial interests on sever.al -occasions. The latest study is that currently under way by The Consolidated Mining and Smelting Company of Canada, Limited. The Company is studying the possibility of making pig iron from the oxide calcine resulting from the roasting of pyrrhotite. tailings used in making sulphuric acid for fertilizer production at Kimberley. A comprehensive report on the subject .of establishing a primary iron and steel works in the Province, based on local iron ores, was prepared by Arthur G. Mc-Kee and Company of Cleveland, Ohio, in 1942 for the B.C. Minister of Mines and is available to interested parties. A detailed survey on the subject was also pre-pared in 1954 by Dr. G. P. Con-tractor, then .of the British Columbia Research Council. Considerable information is there-fore available on most aspects of an integrated primary iron and steel industry in British Columbia to supply the needs of the western provinces. To date, however, no basic iron industry has been established despite the .occurrence of high-grade iron ore deposits on the offshore islands and the high freight charges on iron and steel products brought into the area from Eastern Canada and overseas producers. The chief deterrent has always been the relatively small and highly diversified market available to a local steel producer. Other major fact-ors have been the lack of sufficient proven reserves of iron ore, and the difficulty of making pig iron, suit-able for steel manufacture, economically on a small scale. Technical and economic conditions have changed considerably since World War II and the establishment of a primary industry based on electric furnace production of pig iron or on one of the direct reduction processes, coupled with electric furnace steel production, may now be economically feasible.

Jan 1, 1958

By Paul M. Clifford, David M. Baird

The Great Northern Peninsula of Newfoundland consists of a Precambrian core of gneisses and granitic rocks, cut by numerous diabase dykes. This complex is surrounded by an envelope of sedimentary rocks of Cambrian to Carboniferous age. Radiometric dates from two granite masses in the core give a mini-mum age of -945 m.y. (Grenville) for the last major tectonic activity. This Grenville deformation conferred upon the core substantially its present structure which has controlled later events to a marked degree. Block movements of the core, dominantly in a vertical sense, have ex-posed it to erosion at intervals. The nature and distribution of the flanking sedimentary rocks and the present relief of the peninsula suggest four such movements. THE Great Northern Peninsula extends some 150 miles north-northeast from the northwest corner of the main body of the island of Newfoundland. It separates the Gulf of St. Lawrence from the Atlantic Ocean, except for the 12 mile wide

Jan 1, 1962

By Pamela Paradis-Sokoloski, Deni Thibodeau, J. Denis, Samantha J. Espley, P. O’Donnell

"During the previous decade, the role of spray-on liners within the mining industry was limited to providing a corrosion resistant coating to screen and bolts; however, increasingly, liners are being used as ground support products. Expanding use and testing of liners have demonstrated their ground support function, yet the definitive support mechanism is still under debate. The most promising theory is the retain/hold/reinforcement concept (Kaiser et al.,1992). This conceptual theory has been the basis for the recent underground trials at INCO where, specifically, shotcrete and MIROC Mineguard were tested in two trials to further define limitations and applications of each liner.In a cursory overview, shotcrete is becoming accepted as a support product, while Mineguard is only slowly gaining acceptance.This discrepancy is the result of the corresponding life-spans within the industry, whereby shotcrete has had wide-spread use for decades, yet Mineguard has only recently been introduced. Currently at INCO, shotcrete is primarily used: to provide support in poor ground conditions, to add stability when developing through backfill, and to provide damage control in seismically active mines. It is also used to protect production headings and secondary-blasting chambers from fly-rock damage during blasting. Despite an obvious support function of the liner, shotcrete has always been used in addition to bolts and screen. Comparatively, Mineguard is still in the testing stage, where the greatest potential is increased productivity for applications in multi-tasking development headings. In this scenario, Mineguard provides instant support to replace screen, and bolts temporarily. When the heading has advanced, the drill and support crews work in tandem, drilling off the next round and installing bolts for long-term radial support, respectively. Other potential applications of Mineguard are within production headings to replace screen in the back, and screen and bolts in walls. The potential for both liners to replace conventional support is clearly war-ranted, such that defining the support role was the primary goal of the two underground trials."

Jan 1, 1996

By Marvin E. Lane

Viburnum, located in the foothills of the Ozarks in south-east Missouri, is the site of a modern lead mining and milling operation. Two mines are currently producing a total of 5,000 tons per day and a third mine is in the final development stage, with full production scheduled for late this year (1964). These mines will supply the tonnage required to keep the Viburnum mill operating at a full capacity of 7,000 tons per day for many years. The efficient underground mining operation is completely trackless. Drill jumbos are used to break the ore in a room and pillar method of mining. Transloaders, or St. Joe shovels, and trucks do the loading and hauling. The Viburnum mill has a world-wide reputation as a most efficient operation. This is due to the extensive use of automatic process controls, and labour saving materials handling facilities. Introduction THE St. Joseph Lead Co., has operated lead mines in southeast Missouri for 100 years. These operations have been confined largely to the area called the

Jan 1, 1964

By J. Guha, R. Kanwar, G. Archambault, A. Tremblay

The Copper Rand Cu-Au deposit lies within a shear zone which strikes N50-60W and dips steeply southward (50°-55°) and extends over 1. 5 km with a thickness which varies form 350 to 425 metres. Mineralization, inside the shear zone, is structurally controlled by a dilation mechanism which can be explained by a fracture dilatancy model. The principle of this model involves the mechanics of overriding of irregular planes and surfaces of faults and schistosities, These structures are characteristic features of the Copper Rand shear zone. A structural analysis of the shear zone has been carried out to establish relations between the different structures within the shear zone and their evolution with the development of the shear zone. A geomechanical interpretation of the Copper Rand shear zone explains the formation of internal structures such as faults, schistosities and microstructure during the shearing. This interpretation confirms Ramsay's theoretical model on the geomechanical evolutuion of shear zone development, and the experimental work of Morgenstern-Tchalenko on the simulation of shear zones in clay models. The geomechanical interpretation of the shear zone demonstrates that at the onset, subsidiary fracture patterns are developed in second order faults in the following sequence. At peak strength Riedel shears ( R and R') are formed which propagate outside the strength, restraint (P) shears are developed in the thrust attitude within the shear zones. Principal displacement shears (D) develop toward residual strength in the direction of movement. Shear lenses are formed by the interaction of these shear discontinuities and these facilitate the formation of schis tosi ties with the continuation of the shear displacement within the main shear zone. While the main shear zone and the P and D shears within the main shear zone were in continual movement, the Rand R' structures, once formed, retained a simple fracture pattern and moved little outside the shear limits in comparison to the main shear zone. Parts of these structures inside the shear zone were reactivated by subsequent movements and deformed into folds to account for the present attitudes of the HW-1 and HW-2 and HW-3 structures. This geomechanical model for the shear zone with its subsidiary structures (R, R', P and D shears) is also applied on a larger scale to the Dore Lake shear belt and explains the different structures accompanying it. The initial development of the WNW shears (most are ore deposits) was followed by the subsidiary structures of the Dore Lake shear in a north-south stress field and is well defined by the movements characteristic of the different structures. It is concluded that the Dore Lake shear cannot be the prolongation of the McKenzie Narrows shear but it seems that this prolongation relates to the Henderson-Portage shear zone.

Jan 1, 1984

By T. Peters, W. C. Ferguson

"Shebandowan is about 600 miles west of Sudbury and 50 miles west of Thunderbay close to the trans Canada highway. Shebandowan Lake is about 38 miles long. The ore body is located between No. 1 and No. 2 shafts at the lower end of the lake. The economic mineralization lies between 200 and 2000 feet below. Years ago development of this ore body would probably have entailed draining the lake and using the open pit method to mine the ore.The water of Gold Creek which flows into Lake Shebandowan is representative of all local waters and is very close to rain water in purity. It is obvious that any industrial water discharged would have a measurable impact on the local water. The dissolved solids content is low and consistent with what is normally found in northern Ontario.A Koepe headframe is the only visible evidence of the mine from the lake. The Koepe headframe is esthetically pleasing and quiet in operation. The structure is of concrete to control noise. Noise from ore dumping is controlled by dumping underground to an ore pocket 400 feet below the surface. A 3600 foot conveyor belt carries the ore underground to the mill and is out of sight of the lake and the cottagers. The main objective to all our environmental efforts has been to preserve the natural beauty of the region. The mill is housed in a conventional metal-clad-siding building painted in esthetically pleasing colours. A single service building houses warehouse, dry storage and offices. The area surrounding the mill and service building is paved or grassed and drainage from this area is collected and pumped to the tailings area. Air intake silencers are installed on the compressors which are mounted at the back of the mill. Sound measurements taken on the lake indicate that noise suppression is excellent."

Jan 1, 1975

By Murray Wood, Michael Schaffer, Makat Katom

"An expert system applied to the control of mineral process unit operations is, by its nature, the site best operating practice, having been designed by the local experts in conjunction with consulting metallurgists. The “common sense” layer in a MET (MinnovEX Expert Technology) solution determines an appropriate action for the current operating conditions through a developed heuristic model of the process (expert system). The magnitude of the setpoint change that is made is proportional to the confidence that the system has in its interpretation of the current conditions (fuzzy logic). The solution is always striving to take the process to a constraint and thereby optimise the operation. An accepted limitation of the solution is that the only way the system can determine if a constraint has been reached is to exceed it and then withdraw – essentially “experimenting” with the process. By leveraging a model, which can accurately ""simulate"" the process, this restriction can be circumvented by pre-testing the set point change through a ""what if"" analysis and then modifying the solution as appropriate.At Ok Tedi, the introduction in 1999 of a MET expert system for SAG milling resulted in significant improvement in circuit throughput. Yet, with the additional inclusion of an accurate model of the process there was still more that could be achieved. Hence, in 2002 a MET Neural Network model was developed and deployed to enhance the existing expert system solution. The principal objective of this model was predicting the effect that changes in SAG tonnage and density would have on the power draw of the mill - essentially a power predictor. The results have seen a decrease in process variance with an associated increase in average circuit performance.This paper describes the methodology by which the Neural Network model was implemented, the considerations and limitations when applying this technology and ultimately the results that were achieved."

Jan 1, 2003

By J. C. Loretto

"OPENING REMARKS Yesterday and today we have heard some very interesting papers on operating matters and some of you are probably wondering what we are now doing talking about Communications in Plant Design. Let me tell you! Before the techniques we have heard being discussed can be used, there has to be a properly operating plant. It is certainly a fact that many mineral processing plants achieve only limited success and a number of them can even be said to be failures. Some of you sitting here are probably living with operating problems that are clue to errors in the design.If the histories of these problem plants are examined, it will be found that in many cases, the necessary skills were available during the period of the plant design. There was extensive operating know¬ledge together with a full range of project expertise. Why then the failures? In a substantial number of cases it can be traced to the old, old problem of communications. As plants get bigger, money costs more and smooth startups become more important, it becomes less and less economic to fix up any design errors during plant operations.During our careers in mineral processing, nearly all of us will be involved in at least one plant design and I feel that it is as well if we understand some of these communication difficulties that can lead to a problem plant. There is little point in us being experts in mineral processing if the knowledge we have acquired doesn't somehow get incorporated into the plant.I would, therefore, like to present this short paper that mentions a few of the significant communication problems that can occur during the design of mining and mineral processing plants, together with some thoughts on answers to these problems."

Jan 1, 1973

By B. V. Knelson

"GENTLEMEN:This paper will deal with centrifugal separation - theory and practical, and since the Knelson Concentrator is the only centrifugal concentrator with a properly fluidized bed, this paper will cover the Knelson Concentrator and its technical and structural advances over the last five years. As I am the person with the most experience in this line, I guess I am some kind of an expert; what kind I’m not sure, but some kind.This type of concentrator truly was developed because I’m lazy and I constantly look for easier ways to do things. My experience in the mining industry was very limited but I did realize in looking at placer operations, which is the application where I spring from, that it was tremendously labour intensive and my first reaction that ""my god, there must be some method or way-of handling product in a more efficient (and you can read that as being able to quickly recover very fine particle gold) way than was being shown at that time"". So, the Knelson Concentrator was born - about 6 or 7 years later. Our first attempt was a cone with about the same degree of slope as our present machine and since we had no knowledge of vibration dampening and centrifugal forces at that point, it was just an idea that this should work.Our first run was one of twenty minute duration. We did make that first machine variable speed by a mechanical belt system and we found that at about 240 rpms we were virtually shaking the gravel plant apart that we were attached to. So the first run was twenty minutes and back to the drawing board. However, that first run produced a concentrate so superior to anything we had seen previously, that we knew without any question, we were definately and accurately on the right track."

Jan 1, 1985

By V. I. Lakshmanan, D. A. Mackie

"1. INTRODUCTIONIn the past two decades, low-grade gold and silver ore bodies in the United States have been exploited by heap leaching, primarily with sodium cyanide solutions. This method has proven to be a viable alternative to conventional milling due to its low capital and operating costs. Successes have been made, particularly in Nevada, where ores are well oxidized and the climate is conducive to this method. in recent years, heap leaching has been tried in northern latitudes with some success, however, in using this method, operators face more severe limitations than do their neighbours to the south.This paper evaluates the limitations of heap leaching with particular emphasis on northern climates and introduces an alternative method to recover precious metal values in a continuous vat. This proprietory technology, known as the Mackie Vat Leaching Jig, shows promise, with improved gold recovery and potential to operate in cold climates.2. WHAT ARE THE LIMITATIONS TO HEAP LEACHING?Heap leaching of non-refractory ores is subject to the following limitations:1. Minimum amount of free gold and nuggets in the ore.?. Minerology of the ore--accessibility of gold to lixiviant.3. Minimum particle size and size distribution of crushed product to allow percolation of lixiviant through the heap.4. Minimum amount of clays or clay-like slimes that can cause coating of ore particles and channelling of lixiviant.5. Minimum strength of ore particles or agglomerations to allow economic height of heaps to be built.6. Amount and suitability of real estate.7. Amount and type of precipitation.8. Ambient temperatures.9. Possible poorer lixiviant diffusion.10. Possible lower oxygen content in dissolved cyanide solution with higher heaps, particularly with ice and snow cover."

Jan 1, 1989

By H. R. Bullis

"Abstract- This paper discusses what appears to be a flaw in the current belief, widely held within the gold mining industry and investment community, that the creation of ever-larger gold mining companies is desirable for mining companies and investors alike. The basis of the flaw is in the underlying assumption that very large gold producers can discover or acquire new gold deposits of the size necessary to replace extracted reserves on a year-on-year basis over the intermediate to long term (i.e., five to ten years and longer). As it will be noted in this paper, deposits of the size required to replace annual production of very large gold producers (VLGPs) are relatively few in number. Although discoveries of new gold deposits continue to be made, they are predominantly in the 0.5 to 2.0 million ounce range. Data represented here suggest that, although gold production from individual VLGPs continues to increase, the change is due to merging or acquiring other companies or projects with similar reserve life profiles. Therefore, the reserve life profiles of VLGPs have remained flat or have decreased.The paper will note recent changes in the industry and the remarkable increase in gold production reported by individual mining companies over the past several years. It will provide an overview of the geographical and geological distribution of known gold deposits and the range of deposit sizes. Finally, the paper will discuss the challenges that face large gold producers in replenishing their reserves that are being depleted at an ever-increasing rate. Unless otherwise stated, all production and reserve data have been taken from company documents in the public domain or publicly available information."

Jan 1, 2001

By J. K. Gowans

"INTRODUCTIONTo bring a mining property into production in the Canadian High Arctic a company must deal with the harsh environment, the short shipping season and the high cost of labour. In trying to minimize the effect of these factors, the concept of a barge-mounted process plant was investigated as an alternative to the conventionally built concentrator. Cominco's previous experience gained at the Black Angel Mine on Greenland's west coast suggested that this would be a practical alternative.The normal shipping season at Little Cornwallis Island is approximately six weeks long, from mid-August to the end of September. All equipment and materials must be delivered during this small ''shipping window."" The logistics problems are enormous; if the conventional approach had been used the major process equipment would have been delivered to Little Cornwallis Island at the same time as the completed barge actually was! Construction would also be starting at the start of the worst climatic conditions, the Arctic winter. Nine months production was gained by opting for the ""Barge"" approach.What the Arctic winters do to the shipping season, so do they affect the productivity and the cost of labour. Construction labour must come from southern Canada. Thus higher transportation costs and higher wage rates, with more overtime and incentives, increase the labour costs to approximately 50% over normal southern rates. Couple these rates with the lower productivity involved with men working in the extreme cold temperatures and the net effort is worth avoiding. A process plant being constructed in Southern Canada can take advantage of more accessible labour at lower costs, increased productivity and a faster construction schedule. The barge concept must still deliver the equipment and materials during the ""shipping window"" but it can in the completed form."

Jan 1, 1983

By Michel Ruel

"PID loops – also known as base layers or regulatory controls – form the foundation of any plant’s control layer and it is generally accepted that PID loop health has a direct impact on the plant’s bottom line. Keeping these thousands of control loops in good health has a direct impact on the plant’s bottom line: it reduces variability, improves quality and throughput, and decreases energy costs and raw material usage. This has been well proven and documented in many articles. In the last ten years, technology has evolved: control engineers can now keep track of control loop performance and link it to the root causes of variability. However, they lack industry-wide best practices and criteria for determining what can be considered as excellent, good, fair, or poor performance. To ensure that PID control loops continue to perform well and meet their objectives, control engineers need a combination of (a) an appropriate monitoring technology and (b) best practices for doing the maintenance of base layer controls.Most plants have limited resources and operate with an increasing number of constraints; therefore, using the right tools and including reports in daily workflow is key for success. This paper suggests roles and responsibilities of key players needed to work toward control performance best practices and discuss organisational changes to succeed.INTRODUCTIONAlthough PID controllers are reliable workhorses in the process industry, they are often underrated. Since the 1980’s, computer control has evolved and the control algorithms used by control engineers have become increasingly complex. However, PID controllers still handle over 90% of the control loops in operating plants. Table 1 shows the savings that can be realized by achieving best-practice in several different process control categories (Brisk, 2004). The savings are expressed as a percentage of production costs."

Jan 1, 2011

By S. R. Knowles, R. J. McDonough

"The purpose of this paper is to introduce to the minerals processing marketplace a viable alternative to conventional mechanical agitation and pachuca airlift agitation. What follows is a brief introduction to the Atara Corporation and the fundamentals of how an Atara ""cannon"" mixer operates. The main body of the paper is concerned with the results of a study to evaluate the cannon mixer for a gold cvanide leach application. A brief summary of research and testing for other metallurgical applications is also presented.1. 1 THE COMPANYThe Atara Corporation is a privately owned Canadian company, headquarted in Dorval, Quebec. Its subsidiary, Atara Incorporated, located in Paramus, New Jersey services the municipal wastewater treatment market in the United States. Dorval focuses on industrial mixing applications in Canada and the US. The Atara Corporation provides design, engineering and specifications of agitators for mineral land other) processing applications. Fabrication of mixers is pursued in either Canada or the US, depending on the ultimate destination.Although Atara and its unique static in-tank mixer are relative newcomers to the mining industry, the cannon mixer has demonstrated its value over the past 20 years in municipal wastewater treatment services. In the past four years the Atara unit has been developed for industrial applications; the bulk of the development work has been for metallurgical applications. To-date the cannon mixer has been evaluated for mixing slurries in the following applications: nickel-copper concentrate storage, copper concentrate storage, coal slurry storage, gold cyanide leaching, uranium acid leaching, silver leaching and zinc acid leaching. Atara mixers have been installed with successful performance in full scale tanks containing nickel-copper concentrate slurry (Falconbridge) and gold cyanide leach pulp (Dome"

Jan 1, 1984

By G. A. Kosick, G. S. Dobby

"This paper presents the principles and application of a recently developed control system for flotation columns and column circuits. The control system uses triple pressure sensors to directly sense zone densities and level, and to help in characterizing the operating behaviour of individual columns. A complete expert system development tool is incorporated within the system to provide the facility for full operator training, an on-line help facility, and a means for incorporating the column behavioural patterns into decision making rules. The system is configurable to any number of columns and can be run in either supervisory mode or direct control through Minnovex PIO software. Additional process signals can be interfaced with the system if desired. Operating experience with the control system on the Minnovex column flotation pilot plant is described.I: INTRODUCTIONColumn flotation cells have been more difficult to control and are more sensitive to circuit changes than conventional mechanical flotation cells. This susceptibility encouraged investigation into various types of control strategies ranging from inexpensive single pressure measurements for level control, to highly instrumented and expensive systems using a variety of control methods.Flotation operators, in many cases, do not understand the column control philosophy or have not been trained to deal with this new type of cell. Some operators have subsequently absolved themselves of the column operating responsibility. Some column cells, for example, have run for hours with slurry pouring over the top or no froth coming off at all.ColumnEX is a column flotation control system which was developed from the viewpoint of an operating shift foreman who wishes to:1. control the column or column circuit through a genuine understanding of what is happening inside the columns, and2. to share this knowledge with his flotation operators and be available to guide them through times of circuit upsets."

Jan 1, 1990

By H. P. Jacobi

"The last 25 years have seen tremendous economic pressure placed upon the base metal processor. Industry has responded with technological innovations that have contributed to significant reductions in capital and operating costs. Major changes in processing machinery and philosophy are highlighted for the main unit operations of a base metal mill. Changes in our attitudes on what is environmentally acceptable are also discussed.INTRODUCTIONNewton's law of motion paraphrased states that nothing will change unless there is a pressure to do so.Aase metal processing as a primary commodity related industry has been under severe economic pressure over the last 25 years. This has been brought on by over capacity from new operations in the L.D.C. 's, through material substitution in a host of traditional base metal applications and generally reduced world-wide economic activity. In addition to shrinking markets our collective environmental consciousness has raised effluent standards and workplace hygiene and the employee's as well as government's economic expectations of how much ought to be derived from ''nature's riches''.Industry has responded with technological changes which, it was hoped, would counteract the cost squeeze in which it found itself.I would like to briefly enumerate the major changes, as I see them, that have taken place in the main unit operations that form the normal processing chain for base metals.While the following paper will mention several brands of products, I would like to emphasize that these are the ones that I am most familiar with and is not to say that they are the only manufacturers which have contributed to changes. In fact it ls fair to say that all makers of mining and processing equipment have made improvements to their products, to a greater or lesser degree; they have had to, to still he in business in 1986."

Jan 1, 1987

By Harry Wilton-Clark

Introduction Coal cleaning may be taken as meaning the separation of coal-as-mined into two or more fractions. Coal cleaning includes coal washing, together with any other means used in the ultimate preparation of coal prior to shipment (as coal) . The method of coal cleaning devised for any given mine must be one which is based entirely on the economic results obtainable. The installation of a high-cost and complex washing plant, designed to produce a low-ash dean coal, at the highest possible recovery, may be unsound practice. A crude 'roughing' washer may be the best result of sound engineering and operating consideration, and in some cases coal cleaning should be confined entirely to preparation at the face. Consideration of complete costs, to the point where the coal is actually sold, may show that certain seams are workable or not workable. Of the seams found workable, extraction of the whole or parts of the seam may be decided on. The portion to be extracted may contain rock or bone partings, which must be removed. It may be good practice to mine the extra portion and remove the objectionable materials by surface washing; or it may be that such materials should be removed underground, even at an increased mining cost. For instance, in some of the steeply pitching seams of the Alberta Crow's Nest Pass district, the removal of bone and rock at the face may be almost impossible under the usual 'up the pitch' or 'angle' mining methods, but possible by mining across the pitch so that the material to be rejected can be removed and gobbed. Again, if a complete seam is being extracted, investigation may show marked differences between top coal and bench coal, and if sufficient mine cars are being loaded from a chute at one time, the fact that such a place is working top or bench coal at the time may be reflected by peaks in ash content or size proportions at the ripple. It may be very effective coal preparation to smooth out such peaks.

Jan 1, 1934

By T. V. Simpkinson

Abstract A brief history of the electric arc furnace process of steel-making is given. The greater relative importance of this method of steel manufacture to the Canadian steel industry, as compared with its importance in the steel industry of the United States, is shown. The scope of the process is outlined and brief mention is made of the difficulty of obtaining melting stock low in alloy content. The physical chemistry of steel-making is discussed at length in simple terms, with emphasis on oxidation, de-oxidation, and the role of hydrogen. Carbide-type and silicon-type slags are described and the particular usefulness of each is outlined. The importance of various factors in the melting practice is evaluated on the basis of practical experience. Introduction Although electric furnace steels constitute only a small portion of the total weight of steel used in industrial operations, their importance is relatively much greater than is indicated by comparative tonnage figures. Tool steels, which are vital to all industry, are made almost exclusively by the basic electric arc furnace process, as are stainless steels, valve steels, and the higher alloy types of the class usually referred to as "alloy steels'. For many applications where steel other than electric furnace quality is often used, and when first cost is secondary to performance in service, the extra steel cost of electric furnace quality material is usually returned with interest by consistently longer service life. The electric furnace is pre-eminent in the quality alloy steel field because of the control that may be exercised over conditions of oxidation, de-oxidation, and temperature, the fundamental operations in steel making.

Jan 1, 1948