Search Documents

By W. M. Scheding

"There has recently been a resurgence of interest in unit flotation of mill discharges. At the Kidd Creek concentrator, this technique has been successfully applied to silver flotation in a 3050 mtpd silver-copper-lead-zinc division. The major incentive has been improved silver payment through increased overall recovery and better distribution between the sequential copper, lead and zinc concentrates. A large, but variable fraction of the silver in the ore is present as native silver and, being dense and malleable, is susceptible to overgrinding. Grinding circuit surveys showed high concentrations of silver in both primary and secondary circulating loads. Laboratory testwork confirmed that this was selectively flotable, identified the secondary ball mill discharge as the best feed stream and optimized flotation conditions. A 10 t/h pilot plant campaign confirmed that the rate of accumulation of silver was sufficient to sustain continuous production of a silver concentrate and that flotation of the whole stream was not necessary.The present 30 t/h production circuit recovers from 5 to 50% of the silver in the ore at a concentration ratio between 25 and 250. The circuit also contributes to a better understanding of ore mineralogy, as an 'on-line' indicator of elemental silver content."

Jan 1, 1985

By F. Osmond, R. Kelly

"Malcolm Knowles, the famous adult educator once wrote: ""What a challenge we in human resources development face if we are to avoid the obsolescence of our workforce. I can foresee this challenge requiring that we reconceptualize (...) and redefine the role of HRD, away from that of managing the logistics of conducting training activities to that of managing a system of learning resources"".The context in which this was written surrounds the subject of adult education and the need for business and industry to change its approach to the treatment of adults as learners. In explaining what 'managing a system of learning resources' means, Knowles refers to line supervisors and managers as the most ubiquitous resources for day-in and day-out employee development. In many organizations training has been largely a staff rather than line responsibility. Even where trainers reported to line management, it was still seen as a staff function performed by a few specialists.This change referred to by Knowles places a much heavier responsibility on line supervisors and managers for the development of their personnel than has traditionally been the case. Managing that change - handing over the responsibility to the line organization - is the supreme challenge for the HRD function.Just why is this change necessary? Because too often, the learner does not effectively use on the job what he or she learned in the classroom. In fact, learners often discard new methods and revert to the older ways. The reason training does not stick is that the systems for training and work management are most often separate entities and while one may support the other, they need to be a single integrated system in order to ensure the transfer to the job effectiveness of training and some real value for the training dollars.Because much training can be wasted, steps have to be taken to ensure that it fulfills its intended purpose. The effective and continuing application of knowledge and skills that learners acquire can only be realized when line supervisors and managers are at the centre of the training system.This paper describes how such a systemis being developed at the Iron Ore Company of Canada (IOC) as a functional training program is introduced. The following text provides background information on the IOC - who they are and where they are located, a definition of functional training, an evaluation of the suitability of this approach for adults in industry, a description of how the program is being implemented at IOC and some observations that have been made as this change is experienced."

Jan 1, 1995

By S. P. Cashin, D. Kashuba, W. Esplin

Barrick has had 6 autoclaves in operation at the Goldstrike Mine, North of Carlin Nevada, since 1993. The 6 autoclaves operate in parallel, processing slurry of gold ore. The gold in the ore is predominantly associated with, and encapsulated by, sulphide minerals. It is necessary to oxidize at least 90% of the sulphide mineral before the gold can be concentrated using a cyanide/carbon-in-leach (CIL) circuit. Sulphide oxidation chemical reactions occurring in the autoclaves are exothermic; however, the sulphide content in the ore is not high enough to operate the autoclaves in an auto-thermal mode. Heat from steam is added to the first 2 of 5 autoclave compartments to initiate the sulphide oxidation reactions. The steam used to heat the autoclaves is supplied by three boilers, which are fuelled with propane gas. The completion of a few operations and maintenance projects in the last 2 years has resulted in a 50% reduction in propane energy requirements. The autoclave operating temperatures were minimized. Excess oxygen addition was held as low as possible. The material of construction for the compartment walls inside the autoclaves was changed from brick to Titanium metal. And, the speed of the autoclave slurry agitators was increased. All of these activities had an impact on the propane energy requirements of the autoclaves. Presented below is a description of the autoclave systems, and a discussion of how the energy needs were reduced, resulting in significant operating cost savings.

Jan 1, 2004

Pillars are used in various forms in underground mining. For several decades pillar design has been an issue in both soft and hard rock underground mining. The major use of pillars is in room-and-pillar type mining. Pillars are critical structures in the production levels of block cave mines. With most mines leaning towards the use of block caving for ore extraction today, pillar design has become even more important. Empirical pillar design is popular. The use of numerical modeling is becoming more common in the design of underground mine pillars. A critical review of both the empirical and numerical modeling approaches to the design of underground mine pillars reveal some fundamental flaws. In general, pillar design approaches often assume the pillars are vertical, and are subjected to pure compression. Pillar failure criteria are then based on this assumption. Most papers on numerical modeling for pillar stability assessment use vertical pillars. This paper shows that where pillars are not subjected to pure compression the empirical pillar design approaches are inadequate, and that when using numerical models for the assessment of pillar performance, more care is needed in the determination of the average pillar stresses. The practice of relating field scale pillar strength to laboratory scale intact rock strength determined from conventional laboratory compression tests in empirical design equations is misleading when pillars are inclined or subjected to compressive and shear stresses. New data is added to the hard rock empirical pillar stability chart, and it is shown that it is misleading to conclude that failure of pillars with width to height ratios greater than 2.3 should not be anticipated. New empirical pillar design charts are presented for pillars at various degrees of inclination for different ko-ratios.

Aug 1, 2013

By C. E. Baltzer

This paper highlights the electric power situation in Canada, and introduces brief explanation of the salient differences between electrical practice in the United States and Canada. The availability of bask energy in the two countries is touched on, also the hydro versus thermal outlook as applying to Canada. De-v2lopment of thermal-electric power is dealt with in some detail, followed by Canada's thermal-electric power requirements, present and future. The fuel requirements for steam-electric generating plant are assessed on the basis of a survey recently made, and the location and size of the major thermal plant operations are given. Fuel contractual obligations on the part ?of suppliers and consumers are mentioned. Finally, an opinion is expressed in regard to the types of f.uel in ?demand on a regional basis with emphasis on the need for coal in the several areas dealt with.

Jan 1, 1958

By L. H. Cole

FOR many years Industrial Minerals, or as they were formerly called, 'the Non-Metallic Minerals', compared with the metallics, were considered of only minor importance and as such were given scant attention in the technical press as well as in the public press. Those days are, however, happily passing, and thanks, to an appreciable extent, to the constant endeavour of the Industrial Minerals Section of this Institute, established in the fall of 1932 industrial minerals are now assuming the importance to which they are entitled. The term 'Industrial Minerals', when first adopted in this sense by the Institute, was thought to be original in its application, but it is interesting to note that it had been used many years previously by the Queensland Geological Survey in the following publication: SALT Article 1 in Industrial Minerals by B. DUNSTAN, Chief Government Geologist (Publication No. 268, in Part) Queensland Geological Survey, Department of Mines, Brisbane 1920 In Queensland, however, the term embraced some of the metals as well as the non-metallic minerals proper. The lead furnished by Canada in this matter bore rapid fruit, and already the term 'Industrial Minerals' is widely used, not only throughout Canada but in the United States as well.

Jan 1, 1939

By Gorrell. H. A.

Subsurface water data can be very valuable in .petroleum exploration and research. For the discussion of problems related to subsurface waters uniform nomenclature and classifications are required. The term 'connate water' has frequently been incorrectly used. It should .only be used in its original sense in which it is analagous to 'fossil water'. Classifications .based on origin and on sodium-chloride content are proposed. Present and possible uses of formation water analyses are briefly discussed. Since the potential uses of formation water data are not fully understood, complete analyses of selected samples should be made to insure against future requirements. The subsurface waters of Alberta show considerable regional variation in amount and proportion of dissolved salts.

Jan 1, 1958

By G. A. Buckland

"The development, in Ontario, of a common industry-wide program for the development of skills for employees in underground hard-rock mining is described. This program is designed to increase the productivity of individual workers by improving their skill levels, while at the same time ensuring that employees are instructed in the requisite safety and health aspects of performing various underground tasks. The program's development through a management-labour-government tripartite approach is described. How this program was coordinated with new Government Regulations on Occupational Health and Safety dealing with mandatory training of underground employees is also outlined. IntroductionThis paper will describe briefly what modular training is all about and outline why, and how, it was developed in Ontario on an industry-wide basis. Simply stated, what's been accomplished to date is an industry-wide program for developing the mining skills of underground production employees.The basic objective of this program is to improve the productivity of underground workers. It involves developing an employee's skills to improve his productivity and, because working productively involves knowing how to do a job safely, the program includes instructing an employee in the various safety and health aspects of underground work. An important and, I believe, distinguishing point about the development of this program is that it has been done with the full participation, cooperation and commitment of management, labour and government.It's of considerable interest to note that companies in Ontario who are now using this program are finding that new employees are approximately six months further advanced in productivity than was the case before its use, and in some cases the frequency of accidents has shown a reduction among those employees who have taken this program as compared to those who haven't"

Jan 1, 1980

By G. E. Bogin, C. Strebinger, J. F. Brune

"Evidence shows that methane gas emanates from the mined-out area or gob of a longwall coal mine and can travel towards the working face, posing an explosion risk. Since the gob consists of varying levels of compacted rock, many researchers have modeled fluid flow through the gob as a Darcy-type porous media with a specified porosity and permeability. When studying methane gas explosions near the gob fringe, the Darcy flow assumption may not be applicable to describe the methane flame interaction with the gob. Computational fluid dynamic studies were performed modeling methane flame propagation across a simulated gob which was modeled as both a Darcy porous medium and as discrete rock objects with varying sphericity. Modeling the gob as a Darcy porous medium results in unrealistic methane flame propagation since the porous media assumption does not consider any differences in rock size and/or distribution. Additionally, the porous media model does not allow for ignition within and subsequent flame propagation through the porous medium, which must be modeled to understand the potential for methane gas explosions in the gob area. Modeling the gob as discrete rock objects produces more realistic methane flame dynamics and agrees with experimental observations. Modeling results show flame propagation across circles, hexagons, and squares, meant to represent rock rubble in the gob, produce different levels of turbulence which affects methane flame propagation velocity. This research demonstrates that modeling methane gas explosions in a longwall coal mine environment, specifically near the gob area, requires modeling obstacles, such as rock rubble, as discrete physical objects to capture the complex coupling of fluid dynamics, thermodynamics, and heat transfer. INTRODUCTION Although there are methods to mitigating methane accumulations in a longwall coal mine, explosive gas zones (EGZs) of methane and air may exist and pose an explosion risk to nearby miners and equipment (Brune, 2014) (Karacan, Ruiz, Cote, & Phipps, 2011). In the event of an explosion, the resulting methane flame and pressure wave can be catastrophic as evidenced by the Upper Big Branch explosion in 2010 that killed 29 miners (Page, et al., 2011). Since the mining process is transient, it is difficult to determine exactly where these EGZs exist, but investigative reports show in many cases, these EGZs can be near the working face, behind the shields, or within the gob area (Brune, 2014) (McKinney, et al., 2001). Additionally, miners have recounted seeing flames moving back and forth within the gob and under the roof supports (McKinney, et al., 2001) and in other cases, anecdotal evidence of hearing small pressure pops deep within the gob area (Brune, 2014)."

Jan 1, 2019

By J. De Geoffroy, T. K. Wignall

The paper describes a statistical method based on regression and classification analysis which is designed to assist exploration management in the selection of prospecting areas and drilling targets in regional programs. The classification is based on three criteria which are formulated from sets of relevant geological, geophysical and geochemical factors: (a) regression estimates of expected ore values, (b) Bayesian probabilities of success and (c) expected utility payoffs. The advantages of the method are: (a) rational and unbiased ratings for areas or targets in a manner consistent with management's goals; (b) calculation of probabilities of success and confidence intervals for the ratings, and (c) rapid and accurate handling of a large amount of data by computer programs.

Jan 1, 1970

By J. O. G. Sanderson

Introduction In this paper it is proposed to review the history of petroleum geology in western Canada, to discuss some of the main events which have affected its progress, to mention its relationship to the petroleum industry, and, finally, to appraise its present status and possible future importance. It will be useful first to consider the meanings of the terms petroleum geology, petroleum geologist, and the petroleum geology of a terrain. Petroleum Geology. - In simplest terms, geology is the science of the earth. Hence petroleum geology is the science of that portion of the earth that encloses pools of petroleum. The systematic delineation and study of stratigraphic geology began about 1820. The systematic development and study of petroleum geology started about 1910. It is a relatively immature branch of geology. Petroleum Geologist. - This term may be applied to a fully qualified geologist who is engaged for a time, be it a job, a contract, or a lifetime, in the work of finding and developing deposits of petroleum and related substances. No man may properly be called a petroleum geologist who is not first a fully qualified geologist.

Jan 1, 1946

By Margaret Anne Stephenson

While the concepts of Aboriginal title share a similar jurisprudence in both Australia and Canada resource development regimes on Aboriginal title lands differ significantly. In Australia, the process is the right to negotiate with mining proponents. In Canada, the process is the duty to consult with government regarding mining projects. This paper compares and assesses the processes for ?consultation and negotiation? with Indigenous peoples when development actions (particularly in the context of mining resource development) impact Indigenous property rights and how agreement making can be progressed. This paper will question whether the resource development processes afford Indigenous people?s property rights full respect when mining developments on Indigenous lands are proposed.

Aug 1, 2013

By G. W. Govier

The origin and limitations of the conventional and empirical equation for the interpretation of the results of back pressure tests on gas wells are discussed. Difficulties in data interpretation arise from many causes, including Jack of flow stabilization, uncertainties in connection with the friction calculation, and the effect of turbulence near the sand face in the reservoir. A procedure is developed to ac-count for the turbulence effect. This is based upon the theoretical equation for laminar steady state flow and current knowledge of turbulent steady state flow. The procedure involves the expression of the equation for combined laminar-turbulent steady state flow in terms of a turbulence contribution factor. This factor. is shown to be dependent mainly upon the flow rate per unit of pay thickness and the reservoir permeability. The method of interpretation permits the use of judgment based upon the theory and present day under-standing of laminar-turbulent flow and is considered an improved method

Jan 1, 1961

By Enzo Angeles, Desmond Nanchengwa, Lee Julian, Julian Ruiseco

Since the early 1980s, surface hard-rock mining companies have searched for a blast movement model to enable grade control optimization efforts. Significant time and money were spent attempting to create blast simulations to aid post-blast grade control. Despite nearly 40 years of effort, practical blast movement models remained elusive until computing power reached levels that make real-time simulation possible. From the mid-1990s, mines have been creating in-situ grade control polygons and translating the polygon nodes horizontally to account for blast movement. In many cases, objects are placed in the blast volume and located post-blast to provide local vectors for these node translations. This method was always a compromise between practicality (2D) and reality (3D), but it was the only viable solution that matched the needs of operations. This study considers 21 blasts and evaluates the incremental value achieved by new processes unlocked through 3D modelling, while investigating challenges, limitations, and opportunities for each method.

Jan 1, 2023

By P. Z. Caverhill

In this section of the province only the most meagre of surveys have been made and because these are not sufficient to determine with any degree of accuracy even the total forest area, the information presented in this paper is not complete. Area: -The area south of the Canadian National, and served by the Pacific Great Eastern, is roughly 38,000. square miles, 30,000 of which is classed as productive. This is approximately equal to the productive area of Norway, or half of Finland-or of 30 per cent of Sweden. It is larger than that of either Nova Scotia or New Brunswick. Eliminating from the productive area 3600 square miles of grass-land and areas capable of agricultural development, 26,000 square miles (16,600,000 acres) remains as absolute forest-land, as compared with the 55,000,000 acres of Sweden, the 37,500,000 acres of Finland, the 17,000,000 acres of Norway, and the 7,600,000 acres of Austria.

Jan 1, 1925

By F. Richards

"The property of the Cariboo Gold Quartz Mining Company; Limited; is in the Wells-Barkerville district of Cariboo mining division. It consists of a group of 106 Crown granted mineral claims and fractions; and extends for over 6 miles along what is termed the Barkerville gold belt. The main portal and mine camp are half a mile south of Wells; which lies at the northeast end of Jack of Clubs lake and is reached by a 55-mile motor road from Quesnel; the northern terminus of the Pacific Great Eastern railway.Gold-bearing quartz veins were discovered on the surface in various parts of the property by different prospectors as far back as 1877, but the work that led to the formation of the present company was performed by Al Sanders in the year 1926. Sanders dug trenches and drove small adits on quartz veins containing gold above what is now known as the Sanders zone. Very little underground work has been done beneath the earliest known discovery-the B.C. vein. The Cariboo Gold Quartz Mining Company was formed in the autumn of 1926. The total production of gold from its beginning in 1933 to the end of 1944 has been as follows:"

Jan 1, 1954

By D. W. R. Haysom

"I AM CONSCIOUS of the honour you pay me by having invited me to address you on the subject of the Rehabilitation of the Sydney Steel Corporation. The true architect of the revival and rehabilitation is Robert Burns Cameron. Because of the numerous myths which have grown up around what seems to be the miracle of the revival of the Sydney Steelworks, I propose to go back to the time when they came under the full control of the Province, on the 1st of January, 1968. Late in 1967, the decision was taken by Premier G. I. Smith to keep the Steel Plant running for at least another year, in an endeavour to see whether the enormous losses being sustained by Dosco could be reduced to a level which would permit their continuing operation. When that decision was taken, Dosco was to continue management until the 30th of April, 1968, and in the intervening period, the Provincial Government would seek management of the right calibre to ensure that an objective view of the Steelworks operations could be secured. By a combination of circumstances which can only be described as most felicitous, the man selected for the task was R. B. Cameron. He very quickly determined that to permit Dosco to continue management of the Steelworks until April 30 could only result in heavy losses to the Province and a consequent deterioration in the already critical financial position and a declining morale of the worke"

Jan 1, 1972

By W. R. Cowan

The availability of mineral aggregates for construction purposes is rapidly declining through inadequate resource planning. restrictive zoning and legislation , and competing land uses. The Geological Branch of the Ontario Ministry of Natural Resources has undertaken to provide aggregate inventory reports for all townships designated under The Pits and Quarries Control Act, 1971, and eventually for all towns hips in heavily populated areas. The reports contain maps and recommendations for extractive zoning by municipalities; of necessity only the largest deposits are given priority recommendations. It is intended that these reports should improve the resource planning in areas underlain by large aggregate deposits. The inventory is only possible because a concentrated effort has been made to map the Quaternary geology of populated areas over the last ten years. Future needs require that we develop methods to determine the extent of poorly defined and buried aggregates and that we look for natural alternatives.

Jan 1, 1978

By Sylvain Castonguay, Sylvain Pilon

"Operator competency is an important factor in the safe and successful operation of today’s complex processes. Competent process unit operators deliver superior performance and results. In greenfield projects, operator competency is particularly critical, as the lack of specific operations experience must be offset with proven practical knowledge and skills to avoid mistakes that can cost millions in terms of start-up delays, production losses and equipment damage. It is, therefore, important to know precisely what competencies are required for a project or site, and what any gaps in operator competency need to be addressed and improved. The success of plant commissioning, start-up and sustainable operations is directly tied to operator competency. The significant investments required for new projects, the exploitation of more challenging ore bodies, and the increasing complexity of plant operations have placed renewed emphasis on the need for competent operators. Furthermore, many large capital projects are being developed in remote regions, often with ties to the delivery of social benefits for the local population in terms of jobs, training and other development opportunities. While automation and processing technologies have helped do more with less, indicators now point to a bottleneck in human performance limiting operational results.Automation industry development in managing abnormal situations, including solutions for simulation and operator training, has produced applications to provide customized and flexible training methods. This paper will discuss tools to automate the operator competency process in order to guide trainers to effectively teach, measure, control, provide feedback, and monitor operator skills. Today’s competency management solutions can be effectively applied throughout the course of an operator’s professional life, as a guide to hiring new operators, for developing competencies to support operations, and also to develop and refine best practices and share lessons learned."

Jan 1, 2016

By Paul F. Grundy

The ever changing conditions in the coal-mining industry and the increasing competition of other fuels such as oil, natural gas, wood refuse, etc., have made it imperative that the coal operator be in a position to supply a constantly uniform and clean product. The old idea of putting on the market "anything so long as it's black" no longer holds good. Today's users of fuel have to consider the amount of heat per dollar they obtain from the fuel they buy. Burning of coal has become largely mechanical, at least so far as industrial coal is concerned, and industrial coal is the kind the bituminous operator is for the most part called upon to supply. When we get into things mechanical, the matter of precision has a mighty bearing on efficiency. Precision in coal means standardization of quality, or uniformity of preparation in size and also in ash and moisture content. The trend of coal mining is ever towards more and more mechanization. Mechanization means coal-cutting machinery, loading machinery, conveying machinery, etc. Although such methods cut the cost, the cleanliness of coal so mined and loaded is not controllable to the same extent as when each operation is by hand labour. The operator has therefore the problem of mining his coal as cheaply as possible, but at the same time preparing a product which will to the utmost satisfy his customer. The answer is a mechanical cleaning plant. Before installing a cleaning plant, however, the operator must take into consideration the cleansability of the coal from his particular mine. This is accomplished by taking representative samples of the seam or seams to be treated, and subjecting these to screen tests, followed by float and sink tests on each size product. From these tests, it can be readily found to what degree of cleanliness the several sizes can be prepared advantageously, and also what will be the percentage recovery of cleaned coal. The accompanying tables give the results of representative tests on Michel coals of minus-2-inch size. All coal over 2-inc.h was intended to be hand cleaned. The coal-cleaning plants in general use at the present time come under two broad classifications, namely, wet and dry.

Jan 1, 1934