Search Documents

By T. M. Waterland

A GREAT deal of work has been done at Britannia during the past three years in improving and standardizing rounds for development headings, and the results obtained have been very gratifying. The round which has recently been adopted as a standard for all drifts and cross-cuts has, in some instances, doubled the average length of break formerly obtained. It has also increased the footage of advance per labour shift and reduced explosives' consumption. At the present time, with a shortage of skilled labour, more control is necessar7 in directing the drilling of rounds. The use of a standard round has been o great assistance to the foremen and shiftbosses. NATURE OF GROUND Most of the ground encountered consists of a moderately silicified chlorite schist, known locally as G.M.S (green-mottled schist). It cannot be termed hard ground, because a three and one-half inch Leyner will drill at an average rate of twelve inches per minute. Due to the abrasive nature of the ground, the gauge of the steel wears rapidly and in most cases one set of steel is needed for each hole. The ground is not 'free breaking and holes must be spaced correctly to obtain a maximum break. DEVELOPMENT OF STANDARD ROUND FOR THREE-SHIFT OPERATION Late in 1940, a development programme was started involving 7,000 feet of drifting, 6 ft. By 7 1/2 ft. In cross-section, in two headings. Plans were drawn up to advance the headings on three shifts. Equipment used in the headings was as follows: D.A.35 Leyner?machines, Eimco Model 12B mucking machines, nine one-ton end-dump cars, one Mancha Little Trammer on the longest heading, 20-pound rail, 4-in. 15 compressed-air line, 15-in. Fan pipe connected to 5 h. P. Coppus fan. Diamond-drill cross-cuts, 16 feet in length, were cut every 250 feet. Switches were installed at these cross-cuts and they served as passing points for the cars. One siding seventy feet in length was cut in each heading at approximately the half-way point. The cycle of operations planned was to muck out, drill, and blast each shift. Previous performance in this type of ground indicated that a daily advance of 12 feet to 14 feet might be made. However, if a better type of round could be developed, an increased daily advance would be possible. A study of the time available for each operation in a net working shift of six and one-half hours indicated that the maximum depth of round that could be mucked, drilled, and blasted each shift would be six and one-half feet. When this maximum depth was decided upon, the next problem was to develop a satisfactory round. Due to ventilation difficulties and to the short net working shift, the whole round had to be blasted at one time. In other words, no blasting of the cut-holes could be done.

Jan 1, 1942

SOME months ago a Committee on Deep-level Mining was appointed [by the Government of the Union of South Africa] to consider the possibility of gold mining being carried on at a depth below 8,500 feet. The Committee consisted of Sir Robert Kotze (Chairman) , Mr. H. S. H. Donald (Government Mining Engineer), and Mr. H. R. Hill. The Committee has now made a report which was tabled in the House of Assembly on March 1st. The Committee reported that the tonnage of ore locked up in the deep level areas of the Central Witwatersrand is enormous, and in the 30 miles between Roodepoort and the East Rand Proprietory Mines has a value of about £200,000,000. The Committee says that, with good ventilation, the present system of wet mining, possibly with some modification and with the aid of refrigeration, may be carried to 10,000 feet, but that greater depths will require the adoption of dry mining. "A vigorous campaign of practical experiment into the possibility of dry mining should be initiated, and the Committee recommends to the Government the appointment of a committee of experts, consisting of representatives of the mining industry, the Mines Department, and the medical profession, with the Government Mining Engineer as chairman. The Committee suggests the provision of £30,000 for the first year for the investigations and experiments contemplated, which could best be carried out by an organization which might be styled 'The Rand Mining Research Institute' and constituted somewhat on the Jines of the South African Institute for Medical Research" . The Committee suggests that this committee of experts should arrange for experiments to be made with dry mining in one of the deepest mines, and investigate ventilation, refrigeration, support of workings, and the physiological problems connected with mining. "We emphasize the necessity of treating this whole question as one of importance and urgency. The investigations should be prosecuted with the utmost vigour and should not be delayed at any time for want of funds or for any other reason. If they are not done thoroughly and quickly, the whole scheme might just as well be left severely alone.

Jan 1, 1945

By J. I. Gazzarri

A model of solid oxide fuel cell AC impedance behaviour has been developed and is used to simulate the frequency response of a single cell with and without mechanical damage. The results indicate that the presence of mechanically induced damage within the components of a solid oxide fuel cell can be detected by comparing the frequency response of the undamaged cell with that of a cell in which in-plane cracking or delamination has occurred. The presence of such defects manifests itself as a new semicircle in the Nyquist impedance diagram of the full cell. A parametric study reveals the resolution capabilities of the method in terms of the geometrical characteristics of the defects.

Jan 1, 2005

By François Robert, Rex Brommecker, Don S. Bubar

"The Orenada Zone 4 deposit is a small vein-type gold deposit occurring directly within the Cadillac Break southeast of Val d' Or in southeastern Abitibi Sub province. Mineralization is hosted by the Piche Group which, on the Orenada property, consists of talcchlorite- carbonate, chlorite-carbonate, and sericite-chlorite schists, derived from ultramafic volcanic, mafic igneous, and intermediate to felsic volcaniclastic rocks, respectively. All these rocks have been carbonatized.Rocks of the Pichi Group display a strong east-west, subvertical S1foliation, which is superimposed by asymmetric, intrafolial F2folds with shallow to moderate plunge to the east and to the west. F2folds are accompanied by an S2, subvertical axial planar cleavage, and are interpreted to result from dextral transcurrent shearing along sr.The Zone 4 deposit occurs within a large F2 fold, 60 m wide and plunging at 45 to the east, down to a depth of at least 300m. The auriferous zones consist essentially of zones of closely spaced, parallel quartz-tourmaline-albite-carbonate-arsenopyrite veins concordant to Sr these veins have been folded by the large F2fold and may pre-date the folding. A few discordant quartz-tourmaline-arsenopyrite veins, post- dating the F2 folding, also contain gold. Wallrocks adjacent to concordant veins have been carbonatized, albitized and contain significant amounts of tourmaline and arsenopyrite, with which gold is intimately associated.The Orenada Zone 4 deposit is a unique example of a deformed vein- type gold deposit, and exemplifies one of several types of association of lode gold deposits with folds."

Jan 1, 1990

By V. S. Papezik

Pyrophyllite, an AI silicate used in the production of ceramic materials, is formed mainly by alteration of felsic to intermediate volcanic rocks, either directly (at temperatures of 250-300°C and pressures of 1-2 kbar) or by subsequent low-grade metamorphism of aluminous protoliths produced by thermal fluids or even by prolonged weathering. Most pyrophyllite deposits in North America are concentrated in a belt of Late Precambrian volcanic and sedimentary rocks, the "Avalon Zone ", which extends along the eastern flank of the Appalachian mountain system from Newfoundland to the southeastern U.S.A. The only producing pyrophyllite mine in Canada is an open pit located near the settlement of Foxtrap on the Avalon Peninsula of Newfoundland. It lies in a belt of rhyolitic flows and pyroclastics intruded by a granitoid pluton. The rocks have been leached along a shear- or fracture zone, depleted in silica, alkalies, Ca, Mg and Fe by the action of hydrothermal fluids, and recrystallized to a very fine-grained massive assemblage of pyrophyllite, muscovite ("sericite") and quartz. High-grade pyrophyllite lenses contain small nodules of diaspore with minor barite; rutile is present in trace amounts. The close proximity of all pyrophyllitized zones on the peninsula to the granite contact suggests that the alteration was produced by thermal fluids genetically connected with the granitoid pluton. The fine-grained pyrophyllite-bearing rocks, with their simple mineralogy, are suitable for quantitative modal analysis by X-ray diffraction. Chemically analyzed samples from the alteration zone were used for the construction of working curves by plotting calculated mineral content against the intensity of selected diffraction peaks. The accuracy of the resulting curves is ±4.5% for quartz, ±3.6% for pyrophyllite and ±2.7% for muscovite. Pelletized samples give best results. The XRD method is suitable for a rapid analysis of a large number of grab or core samples to outline higher-grade areas for more detailed sampling.

Jan 1, 1978

By Waldemar W. Koczkodaj, William O. MacKasey

Abstract - A consistency-driven pairwise comparisons method for mineral potential assessment is presented, using a simplified case of volcanic-associated massive sulfide type deposits as an example. Geological, geochemical, and geophysical criteria are considered on two levels: local and regional. The local geological criteria are subdivided into stratigraphy, lithology, alteration and/or mineralization, and structure. The concept of geomerit index and a procedure for computing this index are introduced. The method of consistency-driven pairwise comparisons can be combined with other quantitative and qualitative assessment methods, enhancing them by incorporation of nonmeasurable geological criteria (e.g., stratigraphy or lithology) and by computation of weights. The consistency-driven approach allows experts to refine at-times subjective judgments concerning exploration and land-use planning, and contributes to the improvement of mineral-potential assessments.

Jan 1, 1997

By Waldemar W. Koczkodaj, William O. MacKasey

A consistency-driven pairwise comparisons method for mineral potential assessment is presented, using a simpli?ed case of volcanic-associated massive sul?de type deposits as an example. Geological, geochemical, and geophysical criteria are considered on two levels: local and regional. The local geological criteria are subdivided into stratigraphy, lithology, alteration and/or mineralization, and structure. The concept of geomerit index and a procedure for computing this index are introduced. The method of consistency-driven pairwise comparisons can be combined with other quantitative and qualitative assessment methods, enhancing them by incorporation of non-measurable geological criteria (e.g., stratigraphy or lithology) and by computation of weights. The consistency-driven approach allows experts to re?ne at-times subjective judgments concerning exploration and land-use planning, and contributes to the improvement of mineral-potential assessments.

Jan 1, 1997

By J. Aiello

"Introduction Byron Creek Collieries Limited Corbin mine is located in southeastern British Columbia approximately 180 air kilometres southwest of Calgary (Fig. I), twenty four kilometres south of Highway No. 3 via a newly constructed provincial road (Fig. 2). The development of the area began July 30, 1905, when D.C. Corbin, a prominent businessman from the northwestern U.S., and his associate E.J. Roberts first visited the site of Coal Mountain on horseback. Coal was in great demand by railways and other industrial users, so the Corbin Coal and Coke Co., after acquiring 6,000 hectares of land in the area, began to develop a mine. Mr. Roberts was responsible for the construction of the 22-kilometre rail spur, the Eastern British Columbia Railway, which joined the mine to the CPR main line at the McGillivray Loop. Rail access to the mine and its developing community, Corbin, B.C., was completed in September 1908, the same year that the first underground mine began production. The Corbin Coal and Coke Co. operated six mines on Coal Mountain (Fig. 3) and production from 1908 to 1930 inclusive totalled 2,120,800 tonnes. This production was allocated to the mines as follows:"

Jan 1, 1985

By J. P. Harrison, M. Grenon

"This paper summarizes the results of numerical studies on drift stability in moderately jointed rock masses. It investigates the relative pertinence of geomechanical factors such as joint orientation, spacing and stress regime. This is undertaken using a distinct element model and a series of parametric studies. IntroductionIn evaluating the stability of drifts in jointed rock, it is often necessary to compromise by employing models that capture the complexity of the rock mass, but which are still simple enough to allow for their routine implementation. The distinct element method can arguably provide an eloquent method to accomplish this. This paper explores the applicability of the method by means of a parametric study aiming to identify the dominant factors that influence the stability of drifts in moderately jointed rock. To this end a commercially available 2D distinct element numerical model was used. A series of techniques are presented in an effort to quantify the results of any instability predicted by the model.This paper also demonstrates a case study where a 3D joint network model was integrated into the distinct analysis software package. The advantages, as well as the current limitations of this approach, are discussed."

Jan 1, 2001

By H. Fuchs, W. Hilger, E. Prosser

"The Lone Gull discovery of Urangesellschaft Canada Limited was made in 1974 as a result of extensive exploration activities for unconformity related uranium deposits in the Baker Lake area of the Northwest Territories. The structurally controlled mineralization is hosted in Aphebian metasediments and intrusive granitic stocks located approximately 2 km south of the unconformity between the Lower Proterozoic Aphebian and the Middle Proterozoic The/on Formation.The original discovery was made with a helicopter mounted radiometric system during systematic prospection over the unconformity. Diamond drilling was first carried out in 1977 and continued, with an interruption in 1981, to the present. A total of 25,500 metres and 199 holes have been drilled and outlined three ore zones. Preliminary geological reserves are estimated at some 16 million kgs. U30 8 at an average grade of approximately 0.4%.IntroductionUrangesellschaft initially entered exploration in Canada as a participant in joint ventures in 1968, and was incorporated in Canada in 1974 as Urangesellschaft Canada Limited. Subsequently, UG was among the first companies to apply exploration criteria developed from the Athabasca Basin, namely the Middle Proterozoic unconformity over Archean/ Aphebian basement, for selection of exploration targets in the geologically similar Thelon Basin.The Baker Lake area in the Keewatin District of the Northwest Territories was selected from the extensive Thelon Basin because it had the best accessibility (Fig. 1). The hamlet of Baker Lake located close to the geographical centre of Canada, is largely an Inuit settlement with a population of approximately 1,100 inhabitants. The distance from Baker Lake to the Lone Gull property is about 80 km. Baker Lake is connected to the tidewater of Hudson's Bay via Chesterfield inlet and is serviced by scheduled domestic flights several times weekly from Churchill, Manitoba, about 650 km to the south."

Jan 1, 1986

By E. E. Mason

THE Myrtle group of mining claims is situated on Barkerville mountain in the Cariboo mining district of British Columbia, west of the old mining town of Barkerville. An 1,800-foot adit, known as the Shamrock tunnel, was driven in 1935-36 from the Barkerville road and in the general direction of the Myrtle group. It was proposed to enlarge this adit to more convenient section, extend it 2,500 feet int0 Myrtle ground, and from there drive a main entry 3,000 feet along the length of the group. Several laterals were also to be driven off this main entry as part of the tunnel schedule. It was thus originally proposed to drive 5,500 feet of new adit and 1,800 feet of laterals, a total of 7,300 feet of new work. Work was commenced with a bulldozer on April 21st, 1941, cutting a bench on the hillside for a plant site. The power plant was ready for operation on August 8th. Slashing and re-timbering of the old adit rook longer than was expected. It was found that 57 per cent of the length required timbering, chiefly by fore-poling, and there was also trouble in several sections with swelling ground. First round in the new face was taken on September 17th, when a 2-shift daily schedule was commenced. Due to delays in delivery of electrical equipment, it was not possible to add the third shift until November 14th. From then on, a 3-shift daily schedule was maintained with the exception of holidays and fortnightly change Sundays until August 1st, 1942, when shortage of labour caused the dropping of a shift. All work was suspended on August 14th. The ground through which the tunnel passed was such that the driving was often interrupted by the need of protective timber at the face. Further, crews were continuously employed timbering behind the face, and in maintenance of timbered sections in swelling ground. Roughly 980 feet of the new workings are now timbered, about 21 per cent of the total.

Jan 1, 1942

By Donald MacFadgen

Since 1950, a total of 164 miles of levels and rooms have been roof-bolted in the collieries of the Dominion Coal Company. Roof bolting is an efficient and economic method of sup-port where heavy timber sets or steel booms are necessary for temporary roof support, or where conventional methods of support interfere with the passage of mechanical mining equipment. This paper discusses present roof bolting practices and special bolting applications. THE practice of roof bolting in be collieries of the Dominion Coal Company dates from 1950, when preliminary studies and experiments were carried out in a mechanized room and pillar section of Dominion No. 20 Colliery. These studies were made in close liaison with members of the United States Bureau of Mines who were conducting similar studies. Following the successful application of roof bolting in No. 20 Colliery, this method of roof support was introduced into other collieries

Jan 1, 1963

By W. M. Brewer

Introduction This paper describes some of the mineral resources that are tributary to that portion of the Pacific Great Eastern railway included in the Western Mineral Survey District, No. 6, of British Columbia. This district extends 38 miles northerly from Squamish, the ocean terminus of the railway at the head of Howe sound, to Alta lake. Beyond Alta lake the railway continues northerly through two other mineral survey districts: the Central Mineral Survey District No. 3, and the Northeastern District No. 2. District No. 6 includes that section of the Coast Range from which the waters flow southerly towards Howe sound. The division between District No. 6 and District No. 3 is represented by an imaginary line across the summit between the headwaters of the Cheakamus river, flowing south into the Squamish, and the Green river which flows north and empties into the head of Lillooet lake near Pemberton meadows, about 20 miles from Alta lake. History: - The history of the route of the P. G. E. railway dates back to the old Cariboo days when a pack-horse trail traversed the country northerly from Squamish to the Pemberton meadows, and also south-easterly from Squamish to the head of Seymour creek, thence southerly down that creek to the north arm of Burrard inlet.

Jan 1, 1925

By R. Matusewicz, A. Kaye

Ausmelt Top Submerged Lancing (TSL) Technology has gained widespread commercial acceptance in non-ferrous applications, including the processing of lead and zinc primary concentrates and secondary (post-consumer) materials. TSL is highly flexible and efficient, and is one of the few technologies which can process primary and secondary feeds, and use varying fuels, to deliver high recoveries and excellent environmental performance. With the recent high value of both lead and zinc, and an escalating awareness of the sustainable use of resources, focus on the processing of secondary feed material sources has surged. Ausmelt Technology has proven to be well suited to the economic recovery of values, with twenty-two (22) Ausmelt furnaces processing lead and zinc bearing feed sources now in operation, under design or construction. This paper describes Ausmelt's progress in the fields of lead and zinc processing, and developments in new processing areas such as EAF dust processing and linking to innovative hydrometallurgical technology. Ausmelt has recently committed to the Whyalla Zinc project as the owner/operator of a facility for the treatment of zinc bearing secondary feeds. This project is due for start up in the first quarter of 2008.

Jan 1, 2008

By P. H. Jennings, J. C. T. Farge

Commercial tellurium commonly contains heavy base-metal impurities such as lead, copper, iron, etc., as well as selenium and oxygen. The base metals may be removed by vacuum distillation or by zone melting. Vacuum distillation is a convenient method for treating moderate quantities ( 100 kg.) for the production of a material having a total content of heavy metals in the 10-30 ppm range. By zone melting, it is possible to lower all the heavy metal impurities tm below the limits of spectrographie detection. Neither vacuum distillation nor zone melting is effective for the removal of selenium, but treatment of molten tellurium with hydrogen converts selenium to hydrogen selenide. This procedure is too slow to be considered except as an adjunct to zone melting. In the course of air-melting, many of the more easily oxidized impurities form a dross and may thus be readily removed. Substantial refinement with respect to iron, tin, chromium, aluminum, sodium, silicon, magnesium, calcium and manganese can be achieved in this way. Although tellurium can be electrodeposited from either acid or alkaline solutions of the dioxide, various factors militate against successful electro-refining, amongst which may be mentioned the brittleness of cast tellurium anodes and the tendency for the metal to be deposited in dendritic form, even at low current densities.

Jan 1, 1966

By J. O. Wheeler

"DEFINITION OF THE REGION, ITS BOUNDARIES, AND PHYSICAL AND GE'OLOGICAL CHARACTERISTICSTHIS PAPER concerns the Western Cordilleran region, embracing most of British Columbia, the southern half of Yukon Territory and the southwesternmost part of the District of MacKenzie. It excludes Vancouver Island and the Queen Charlotte Islands, which are discussed in a background paper on the Pacific Continental Shelf. The region is bounded on the south by the northwestern United States, on the west by the continental shelf and Alaska, on the north by the front of the Ogilvie Mountains, on the northeast by the axis of the MacKenzie Mountains and on the east by the Rocky Mountain Trench.The region is dominated by two mountain chains that con tain icefields and glaciers: the St. Elias, Coast and Cascade Mountains in the west; the Selwyn, Pelly, Cassiar, Omineca and Columbia Mountains in the east. The Intermontane region between these mountain chains consists of lower mountains and plateaus. In the mountains, the region above the timberline and many of the steep valley-walls provide good exposures of rock, but these areas are subject to rockslides and landslides and in winter to snow avalanches. Much of the Western Cordillera was covered by ice-sheets at various times during the Pleistocene epoch. Consequently, the larger valleys in the mountains and much of the Intermontane region contain much glacial drift and alluvium and only limited exposures of rock. This same terrain in the Southern Cordillera, however, is the most favourable for agriculture. Parts of the region, particularly in the two mountain chains, are heavily forested. Elsewhere, the forest cover is less, with grassland prevailing in the south and tundra in the north."

Jan 1, 1970

By Stefan Boshkov

THE ADVENT of mining at great depth has brought to the fore the question of stresses around mine openings. The many-pronged attack on this problem is certified by the accelerated appearance, in the mining literature, of articles on various topics related to this subject (1). Whereas it may be agreed that we, of the mining profession, have fallen woefully behind in research and the development of an understanding of this important facet of the general problem of mining, it must also be accepted that the analysis of the stresses in a mine structure is usually more complex than is the case in the majority of structures encountered and dealt with in civil engineering. Whereas homogeneity and isotropy are readily acceptable for most metals, such properties are but crudely approximated in rocks. Whereas the external loads on a structure in civil engineering may be readily determined, those on a mining structure are subject to ?conjecture. Whereas the limits of the structure may readily be defined in civil engineering, the boundaries of the mining structure are, in most cases, indeterminate, and subject to intelligent guesswork, at best.

Jan 1, 1956

By A. G. Matyas

Process improvements which have reduced the lead content of slag from the Brunswick lead blast furnace are described. Microscope examination and electron microprobe analyses, supported by the results of slag settling and viscosity tests, showed that typically about 70% of the lead in the lead blast-furnace slag was present in the form of entrained prills of metallic lead. The total lead content was found to increase with the magnetic susceptibility of the slag. Measurements in the furnace settler indicated the presence of a magnetite-rich layer between bullion and slag, arising from high magnetite levels in the slag. This layer was believed to inhibit the settling of entrained lead from the slag. Tracer tests showed that the average slag residence time in the settler was less than 2 minutes. Improvements in coke quality and sizing, which led to a reduction in the slag magnetite content, and the installation of a larger settler and a continuous Roy tapper, have all contributed to a significant decrease in the slag lead content.

Jan 1, 1977

By Kimiz Dalkir

Some things to keep in mind? ! What is your role in knowledge management? ! What knowledge-related challenges are you facing today? ! How does important knowledge get shared in your organization? ! Can you name factors that enable/block innovation and organizational learning in your work context? A brief history of KM? ! Top-down / imposed ! Rigid / bureaucratic ! Slow deployments ! Expensive ! Unpopular: empty libraries, info-junkyards, low adoption rates ! Problems measuring success ! The result: traditional KM is not the answer

May 1, 2003

By H. Hejny

Economy needs mineral raw materials in almost each sector of modern life. They can only be provided by mining activities. An increasing share of the total mining production will be by underground mining. The mineral deposits will be found at gradually greater depths, including all problems associated with them. It involves an increase in overburden pressure with subsequent rock stability problems and risks of structural collapse. There is a need for new and safe technologies for almost all parts of a modern mine. The mining industry faces a number of challenges which require technical solutions that encompass the entire network and include the economic, social and environmental issues. The industry needs a new image based on pioneering solutions and a modern structure that can exploit minerals at greater depths and promote both high productivity and safe working conditions. Funding has been secured from the European Commission for the I²Mine project. Work started in November, 2011. This initiative is designed to focus on the technological challenges that the mining industry is currently facing including the exploitation of ever deeper deposits and the aspiration for an invisible, safe, zero impact mine. The project comprises a consortium of 27 organisations from 10 European countries. I²Mine marks the start of a series of development activities aimed at realising the concept of an invisible, zero impact, deep mine. The extractive sector, still seen as being old fashioned and environmentally unfriendly, will show that mineral extraction and processing can be done in a highly innovative and sustainable manner with low impact underground and zero impact above ground. The concept of I²Mine is to develop innovative methods, technologies, machines and equipment necessary for the efficient exploitation of minerals and disposal of waste, all of which will be carried out underground. This will dramatically reduce the volume of surface transportation of both minerals and waste, minimising above ground installations and reducing the environmental impact. New eco-efficient technologies will be applied in order to make the entire mining process more efficient and environmentally sound. The concept is for an integrated mine, with the majority of the installations underground, and only the final product will be transported above ground to be shipped to the customer. Production waste will be treated and stored underground and gaseous emissions will be managed underground as far as practical. I²Mine will also focus on ideas and concepts that increase energy efficiency and decrease waste. The core of the project will be to develop breakthrough technologies for autonomous, highly selective, continuous mineral extraction processes and machinery based on new sensor technologies, face front separation as well as innovative concepts for mass flow management and transportation integrating state of the art technologies. The concept of an invisible, zero impact mine requires a refined process underground that selectively extracts the mineral thereby reducing waste. For this reason, improved extraction machines and near to face processing methods, including backfill procedures, need to be developed. These developments include rock mechanics and ground control solutions, incorporating health, safety and environmental issues.

Aug 1, 2013