Search Documents

By J. L. Wilson

"Many modern concentrators with VSD driven SAG mills still rely on the control room operator to manually adjust the speed in reaction to increasing bearing pressure. All too often, the problem with this strategy is by the time the operator reacts with a sudden speed increase, the SAG Mill is likely already on its way to loading up. To assist the new operators, the SAG Mill at B2Gold’s Fekola Mine in Mali needed a robust control that could handle load changes and unmeasured disturbances with minimal operator intervention. With modern Distributed Control Systems (DCS) powerful enough to run advanced control, they often have Model Predictive Control (MPC) blocks built in or available as an “add-on” license, and thus MPC can be readily implemented within the modern concentrator with a relatively low added capital cost. This paper discusses an implementation of two single output MPC controllers to control the SAG Mill at Fekola. This was implemented using the existing signals and advanced control blocks available to the installed DCS.INTRODUCTION Many modern concentrators with VSD driven SAG mills still rely on the control room operator to manually adjust the speed in reaction to increasing bearing pressure. All too often, the problem with this strategy is that by the time the operator reacts with a sudden speed increase, the SAG Mill is likely already on its way to loading up. The next step the operator may take may be to cut back the feed rate, or production until the SAG is once again stable. With this sudden reaction comes an abrupt change in SAG rotational speed and power consumption that sends a surge of material down the circuit as the mill suddenly ejects more pulp. Furthermore, choosing a higher rotational speed can lead to higher than normal liner wear as the cataract overshoots the toe of the charge and impacts the liners. After start-up at B2Gold’s Fekola Gold Mine in 2017, the SAG mill was being controlled manually. The SAG rotational speed was adjusted manually by the operator in step changes depending on whether the SAG bearing pressure was increasing, decreasing or stable. During this time of manual control, the SAG fresh feed rate was also adjusted to a tonnage setpoint with a PID controller. Generally, the SAG fresh feed rate setpoint was kept at a target value, but then the feed rate was throttled back if the SAG mill or grinding circuit showed signs of overloading. The extra challenges were that the operators had limited experience and were concurrently learning how the plant operated. Also, they were also occupied with managing situations in the rest of the plant. Often their attention was drawn away from the SAG mill and during that time, the SAG Mill would load up before they could react."

Jan 1, 2019

By C. Samuelsson, H. Ahmed, B Björkman, A. Andersson

The cost of raw material and energy is a continuing driving force towards working with increasing the recycling of ore based steelmaking residues. In Sweden no on-site sinter plants are operated at the integrated steelworks. Instead, selected residues from the plant are incorporated in a cold bonded briquette product which is recycled to the process via the blast furnace (BF). Since the BF sludge is the major bleed of zinc out of the furnace it is required to be de-zinced prior to recycling in the briquette product. In the present work landfilled BF sludge has been characterized with respect to chemical composition, particle size distribution, X-ray diffraction (XRD), and scanning electron microscopy (SEM). The sludge was also subjected to laboratory scale hydrocyclone trials aiming at reducing the zinc content making the sludge viable for recycling. The results suggested that the sludge had been agglomerated prior to the characterization and hydrocyclone treatment. The zinc removal using the hydrocyclone was discussed.

Jan 1, 2015

By W. G. Stevenson

With the author's background of extensive experience, this paper delineates the role of the prospector in modern-day exploration programs. The stages in the development of a prospect to a producing mineral district are outlined, and examples are given from the Ross River area of the Yukon Territory and the Peachland and Highland Valley areas of British Columbia.

Jan 1, 1970

By E. Herrera, L. Mariscal

"Ilo Copper Smelter operates since 2007 with an ISASMELTTM furnace as a single smelting unit (1,200,000 tpy) associated with two Rotary Holding Furnaces for separation of matte and slag, and which directly produces a discard slag. Southern Peru continually has been improving the slag chemistry of its ISASMELTTM furnace in order to reduce copper losses, given its big economic impact due to large slag mass generation. The present paper describes the influence of the CaO, Al2O3 and magnetite content in the slag of the ISASMELTTM furnace correlated with the SiO2/Fe ratio and its liquidus slag. Also it defines the best slag chemistry and operating practice in order to reduce the copper losses without compromise the bricks life of the furnace.INTRODUCTIONIlo Copper Smelter of Southern Peru (Grupo Mexico) is located on the southern coast of Peru, and treats mainly copper concentrates produced in its own mines (Toquepala and Cuajone).The modernized smelter was commissioned in 2007 and operates with an ISASMELT™ furnace as a single smelting unit (1,200,000 tpy), which is associated with two Rotary Holding Furnaces (RHF) for separation of matte and slag. This slag is directly sent to the dump. Figure 1 shows the smelter flow diagram.The ISASMELT™ process is a bath-smelting process using a single lance. The lance tip is immersed into a molten slag bath contained within the stationary, vertical, refractory-lined ISASMELT™ furnace. The injection of oxygen-enriched air, through the lance into the slag results in a highly turbulent molten bath. Feed material falling into the turbulent bath from above reacts rapidly, resulting in extremely high productivity for a relatively small bath volume."

Jan 1, 2012

By Jacob Masliyah, Zhiang Zhou, Tshitende Kasongo, Jianjun Liu, Zhenghe Xu, Jeawon Choung

"Slime coating is a recognized challenge in fine particle flotation, not only in decreasing recovery, but also in reducing the selectivity and hence froth quality. In this presentation, a novel method based on electrophoretic mobility distribution measurement to study slime coatings is described. By measuring electrophoretic mobility distribution of individual minerals and their mixtures, the interactions between these minerals can be evaluated.For illustrative purposes, a model system of fine coals, or oil sands with two different types of fine clays was studied. Flotation tests showed a significant decrease in coal (bitumen) flotation recovery with montmorillonite but not with kaolinite clay addition. When electrophoretic mobility distribution of a fine coal/montmorillonite clay mixture was measured, a single modal zeta potential distribution was obtained, in contrast to a bimodal distribution for fine coalkaolinite clay mixture. This finding suggests a stronger adhesion of montmorillonite than kaolinite clays on fine coal surfaces. In the case of bitumen, the bimodal zeta potential distribution was measured for the mixture of bitumen emulsion and kaolinite or montmorillonite, indicating a weak attraction of the clays by bitumen. In the presence of calcium, however, a single modal zeta potential distribution was obtained in the mixture of bitumen emulsion with montmorillonite but not kaolinite clays. These findings are in excellent agreement with bitumen flotation results, demonstrating that the electrophoretic distribution measurement is a powerful tool to study slime coating phenomenon in a complex fine particle flotation system."

Jan 1, 2002

By Ramsey Hart

MiningWatch Canada is the only national independent civil society organization with an exclusive focus on mining in Canada and Canadian mining companies operations internationally. In 2005, MiningWatch Canada collaborated with other NGOs to develop the Framework for Responsible Mining: A Guide to Evolving Standards. The project was the result of a perceived need by NGOs and retailers, particularly from the jewellery sector, for a framework that would set out environmental, social, and governance standards for the minerals sector ?providing recommendations for retailers and others seeking to source or invest responsibly, as well as regulate and encourage responsible mining practices?. This paper is a reflection on the Framework that examines key areas of concern and notes where the industry norms and expectations of civil society have evolved. The paper focuses on developments in social issues related to the UN Guiding Principles on Business and Human Rights, new initiatives associated with financial transparency, the UN Declaration on the Rights of Indigenous Peoples. The environmental components of the Framework that are revisited are waste management, biodiversity, energy and climate change, environmental assessment, mine closure, mercury and seabed mining.

Aug 1, 2013

By J. J. Benitez

MIBC (methyl-isobuthyl carbinol) was previously shown to enhance significantly sylvite flotation when used at the stage of preparation of amine dispersions. In this paper Atomic Force Microscopy (AFM) is used to study the effect of MIBC on deposition of octadecylamine (ODA) on the surface of mica. The AFM images indicate that amino terminated, and therefore hydrophilic, deposits of ODA are observed on the mica surface in the ODA dispersions free of MIBC. In the presence of MIBC a methyl terminated (hydrophobic) monolayer is obtained on the mica surface. The transition between the monolayer and bilayer phases is due to the presence of MIBC. Experiments carried out in distilled water reproduced the results obtained from the brine. Working in pure water instead of brine simplifies the preparation conditions and the analysis by AFM.

Jan 1, 2006

By H. Q. Fan

Construction equipment is an important type of resources of heavy construction contractors. Since equipment breakdowns can cause project delays and significant financial losses, the contractors are eager to know those factors causing equipment failures directly or indirectly, related to equipment design, maintenance, and operations. Although Bayesian network can be used for diagnostic analysis of failure events or making predictive analysis, building a Bayesian network for such purpose can be difficult as the cause-effect relations can be subjective and their conditional probabilities change with a wide variety of causal factors. A hybrid approach is proposed in this paper to update the Bayesian diagnostic network structures and parameters using real life data, the conditional probabilities and cause-effect relationships can be dynamically updated with observed failure records to reflect the real life situations of a complex equipment system. A case study is conducted to show the benefits of the hybrid approach in construction equipment diagnostic analysis.

Aug 1, 2013

"Gravity concentration remains the main separation method for fine iron ore and is used extensively for treating various minerals. Gravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid, such as water or air (Wills, 2006).Spirals concentrators are one of the gravity concentration equipment used for beneficiation of minerals. Spirals are typically used for processing of fine minerals (-1mm) size fraction. The main operating variables for a spiral concentrator are the feed rate, the solids concentration, the wash water addition and the position of the cutters or splitters used to separate the tailings, middling and concentrate streams (Sadeghi, Bazin & Renaud, 2014).The aim of this study is to investigate the effect of feed rate, solids concentration and wash water on grade and recovery on iron ore material. The Multotec SC20HC/7 WW spiral was used for the experimental test work. The spiral was tested at varying solids concentration and feed rate. The wash water rate was also varied to establish the best washing rate. The splitter positions were kept constant. Optimization of these variables is expected to provide optimum conditions for a good compromise between grade and recovery.INTRODUCTIONSpiral concentrators are simple low energy consuming devices that separate minerals mainly on the basis of density. Spirals are widely used in mineral processing as a method for preconcentration and have proven to be metallurgically efficient and cost effective.Spirals have a wide application, they are used in iron ore processing, coal, gold, chromites, mineral sands, glass sands, and in soil cleaning.Separation on a spiral is achieved through a combination of forces that act on particles as they move down the trough of the spiral. The main forces known to act on the particle on a spiral are the gravitational forces, centrifugal force, hydrodynamic drag, and lift and friction forces (Kapur & Meloy, 1998). Apart from the forces acting on a spiral, the properties of the slurry flowing on a spiral including, solids concentration, feed rate and wash water also plays an important role in the separation on the spiral.The relationship between separation efficiency and feed rate was shown to be linear, with a decrease in efficiency at higher flow rates. Previous work on flow profile by Holland - Batt (1990) indicated that any increase in the feed rate to a spiral results in a greater part of the additional flow volume reporting to the outside of the trough. The flow on the outside of the trough becomes energized and consequence to that the heavy particles find it hard to settle and escape this region to the inner region. This effect has a high impact on recovery of heavy minerals, since any increase in volumetric flow on the spiral is not made available for recovery in the inner region of the spiral."

Jan 1, 2015

By N. Campbell

"The fault under consideration follows a northerly trend past the west; side of the original settlement of Yell ow knife; which is situated 600 miles; north of Edmonton and 400 miles from the Northern Alberta Railway; terminus at Waterways; Alberta. The mining properties chiefly concerned; include the southern part of the Giant claims; on the east side of the fault; and the Con-Rycon-Demelt claims; on the west side 3 1/2 miles to the south.; Geological data were also obtained from the eastern part of the A.Y.E.; property; which lies south of the Giant claims; and from the Negus; Meg; Yellorex; and Kam properties; which are south and southeast of the ConRycon-; Demelt claims (see Frontispiece; also Fig. 5).Recognition of the major faults in the Yellowknife Bay area, including the West Bay fault, which appears to be the greatest, resulted from the work of A. W. Jolliffe (formerly of the Geological Survey of Canada) in 1935 and subsequent years. It has been stated with little exaggeration that these faults rank with the largest known steeply dipping dislocations of the earth's crust.In the winter of 1939, a mineralized shear zone named the 'Creek vein' was found on the Giant property. It was noted that the space relationship between this shear zone and a body of quartz-feldspar porphyry is roughly the same as that between the Con C-4 shear zone and a body of acid flows lying north of the Con property. Coupling this relationship with the assumption that the movement along the fault is dominantly horizontal, it was postulated that the Giant shear zone represented the faulted extension of the Con C-4 shear zone.As geological information became more extensive, certain weaknesses in this concept became apparent, and when spectacular orebodies were discovered on the Giant property in 1944 the question of possible faulted extensions became an important consideration. Consequently, in the spring of 1944, an extended investigation was undertaken, the results of which are embodied in this paper."

Jan 1, 1954

By Kish. L.

"The results of a chemical and mineralogical study of eighteen opaque-oxide occurrences are discussed and the detailed chemical, metallurgical and mining feasibility study of a vanadium-rich magnetite deposit is summarized. A plot of the mol-percentages in the system FeO- Fe2O 3-TiO2 indicates that the deposits fall into two distinct groups: some contain hematite with ilmenite, and some others have magnetite with ilmenite (titaniferous magnetites). The plot also suggests that the two types of deposits were crystallized from liquids of different compositions. Each group has its distinct structural features. Vanadium is present in all of the studied specimens, however concentrations of economic importance have so far been found only in the titaniferous magnetite deposits. The vanadium content of the oxide concentrations of the Dore Lake Complex is the largest among the studied occurrences. Analyses of the concentrates of the drill-core sections show a compositional variation across the orebody; a continuous increase in the tenor of Ti02 and a decrease in the vanadium content upward in the layered sequence is found. Concentration tests on several tons of samples indicate that about 80 per cent of the vanadium is recovered in the magnetite concentrate."

Jan 1, 1972

By F. G. Vetsch, F. A. Ronaghan

"Introduction1N THE FALL of 1951, Peace River Allied Fort St. John No. 1 well was drilled in Lsd. 1, Section 9 Township 83, Range 18, West of the 6th Meridian, on the flats of the north side of Peace river, six miles southeast of the village of Fort St. John, B.C. During this operation, non-commercial shows gas in three zones and of oil in one zone were obtained during the drill-stem tests. Further geological study indicated that this well was on the southeastern edge of the Fort St. St. John structure.Pacific Fort St. John No. 4, drilled shortly afterwards, obtained possible commercial gas flows on drill-stem test in five zones and thus encouraged development of what has become Canada's largest multizone gas field.In general, the productive horizons in this area possess fair per-meabilities and high porosities, a combination which provides for high reserves and moderate productivities. Development to date has therefore stressed experimental techniques in drilling and completion practice to provide high deliverability wells.Data and information of a specific nature apply, in all cases, to the pools in the Fort St. John structure."

Jan 1, 1954

By J. E. Nesset, E. R. Bobicki, K. L. Bilaniuk

The introduction of froth flotation technology in Canada, and in particular, in British Columbia, began not long after it was successfully applied in the Broken Hill mining area of Australia which began around 1905. It proved to be a revolutionary and transformative technology that resulted in marginal operations in copper, lead and zinc becoming profitable in spectacular fashion. The paper presents the technology of both oil flotation and froth flotation in the context of the challenges of the time and its early application in British Columbia at the Le Roi No.2 mine (1903), the Britannia Copper mine (1912), and at the Allenby concentrator of the Copper Mountain mine (1918-19). New-found archival documents indicate the Britannia application to be the first production application of froth flotation for copper ore outside Australia, a claim that is currently made by the Braden mine (now El Teniente) in Chile. Flotation was initially an add-on process following gravity methods but was rapidly shown to be far superior method for the bulk and selective recovery of metal sulphides. Flotation proved particularly successful for the recovery of zinc sulphide (the so-called ‘zinc problem’) which was considered a contaminant at the time. The ‘copper problem’ related to the poor recovery of fine copper sulphide particles that were not amenable to gravity methods. The success of flotation led to changes in both the scale and methods of mining, concentration and smelting in a manner that allowed integrated mining companies to flourish. Many are still with us today. INTRODUCTION The advent of froth flotation in the early 20th century was truly a revolutionary technological development, not only for the mining and metallurgical industries, but arguably more so for business and society overall. The Canadian technology historian Jeremy Mouat stated (1996) “The development of flotation was the greatest single metallurgical improvement of the modern era...it is not overstating the case to claim that flotation was of central importance to the smooth functioning of the global economy”. It should, therefore, be a story of interest to us all. The aim of this paper is not to retell the full story, that has been well covered by others (Hoover, 1912; Rickard, 1916a; Hines & Vincent, 1961; Lynch et al., 2010) but rather to add some Canadian perspective and the key role played by companies and individuals in those early days, focusing on events in British Columbia’s copper industry. EARLY DEVELOPMENTS During the later half of the 19th century, a number of flotation-related patents were issued. These include the 1860 patent (Britain) granted to William Haynes for a process to separate sulphides from ground ore by mixing it with oil (1-10% wt) followed by a separation process in a water-filled vessel; the 1877 patent granted to Georg and Adolph Bessel (Germany) for a process involving the mixing of oil and graphite ore followed by boiling in water to produce a high grade graphite froth (>90% carbon); and the 1885 patent granted to Rebecca ‘Carrie’ Everson for the separation of sulphides by mixing sulphide ore with small quantities of oil, and adding water followed by sulphuric acid. These processes are more properly referred to as bulk oil flotation due to the relatively large quantity of hydrocarbon used.

Jan 1, 2019

By Glenn Norris, Tyler Buckingham

"Gold recovery gains in the order of one to two percent have been realized in 2009 due to changes in the operation of the grinding circuits at Barrick Gold Corporation’s Hemlo - Williams Mill. The initiative known as “split milling” involves milling low grade open pit ore in one grinding circuit and higher grade underground ore in the other grinding circuit under different conditions.The philosophy of split milling involves processing higher grade underground ore at a lower throughput rate and a finer grind while milling lower grade open pit ore at a higher throughput rate and a coarser grind. Bench scale tests showed that the recovery relationship for underground ore sources was much more grind sensitive than that of open pit ore. This relationship proved to hold in the plant. The gold recovery gain due to finer grinding of the higher grade ore is much greater than the recovery loss due to coarser grinding on the lower grade ore. Since the majority of gold is being recovered at a higher rate, this results in higher overall plant gold recovery when compared to the traditional operation philosophy of blending the ore sources.The challenges for achieving the maximum benefits of split milling were two fold; the need to increase throughput on the open pit ore milling circuit and a means of grinding finer on the underground circuit. The former was met with an increase in SAG (Semi-Autogenous Grinding) mill ball charge, a basic “drill to mill” blasting campaign and changes to the primary gyratory crusher. The latter was met with a reduced SAG mill ball charge and a higher milling density. The resulting benefits in additional gold recovered are in the order of $3-5 million per annum.INTRODUCTIONThe Williams Mill processes ore from three different ore sources, the David Bell Mine (DB), the Williams Underground Mine (WUG) and the Williams Open Pit (OP). All three ore sources are located within the Hemlo camp in Northwestern Ontario adjacent to the Trans-Canada Highway. The Williams Mill was built in the mid 1980’s at which time it was designed to process 3,000 dry metric tonnes per day through a 22’ SAG mill in series with a 16’ ball mill. In 1988 a Mill expansion doubled the mill capacity by adding a second identical grinding circuit. A photo of the current grinding circuit can be seen in Figure 1. Today the Williams Mill processes an average of 8,000 tonnes per day of which approximately 60% is from the Williams Open Pit."

Jan 1, 2010

By M. D. Gerst

The degree to which copper will continue to be in an integral part of the world economy in the future will depend largely on the dynamics of global economic development, the primary and secondary copper resource stock, technological change, and potential environmental constraints. We have characterized the copper cycle of 1994 for all of Earth's regions and for the planet itself (T. Graedel et al., Environmental Science & Technology, 38, 1242-1252, 2004) and recently updated that cycle to year 2000. In this paper, we compare various features of the 1994 and 2000 cycles. The three largest-using regions, Asia, Europe, and North America, all increased their absolute rate of copper use between 1994 and 2000, and all increased the per-capita rate of copper use as well. Globally, the use of copper increased by about 32%, from 11.7 to 15.3 million metric tons, while population increased by only 8%. Various changes are seen in scrap trade, finished products trade, and other parameters of the cycle. We conclude by considering how the rates of technological change and growth in demand, especially in Asia, may influence the copper cycle in the years ahead.

Jan 1, 2007

By Scott Rosenthal

?EMESRT History ?Design Philosophies (DP?s) ?Industry Successes ?Participation Thinking Differently Earth Moving Equipment Safety Round Table ? Use a critical mass to influence Marketing ? Define ?Problems?not ?Solutions? ? Leave the OEM designers to develop solutions Work within the companies to improve purchasing

May 1, 2010

By Z. Yang, M. J. Collins, N. E. Tuffrey, R. J. Kalanchey, I. M. Masters

The high elevation of China Western Mining Company (WMC)' s Ganhe refinery, and the high iron content of concentrates produced by the WMC mines, were key factors in the selection of pressure leaching by WMC for their new zinc refinery. This paper describes the results of pressure leaching test work conducted by Sherritt in Fort Saskatchewan with a sample of WMC concentrate from Qinghai Province in China. Results from batch pressure leach tests and a four-day pilot plant campaign are reported. The pilot plant campaign included continuous operation of a two-stage pressure leach circuit, as well as neutralization and iron removal steps, resulting in the production of iron-free zinc sulphate solution. Greater than 98% zinc extraction was achieved in pressure leaching, while producing solution containing about 9 g/L H2SO4 and 2 g/L Fe. Following neutralization and iron removal, the solution contained about 170 g/L Zn and less than 10 mg/L Fe. Overall recovery of sulphur in the zinc concentrate feed to elemental sulphur byproduct was about 85%, while 75 to 80% of the indium in the feed was recoverable from the neutralization residue. The test results highlighted the technical and economic advantages offered by the Sherritt Zinc Pressure Leach Process and provided the required data for the engineering design.

Jan 1, 2008

By J. F. Wright

During the last three years prospecting has been active in southeastern Manitoba and a number of interesting gold, nickel and copper deposits have been discovered within an area 90 miles north of the international boundary, and extending about 40 miles westerly from between mileage 60 and 110 on the Manitoba-Ontario boundary. As known at present, two-thirds of this area of 2,000 square miles is underlain by pre Cambrian granite and granite gneiss and is not likely to contain mineral deposits of economic importance. The remaining one-third is underlain by metamorphosed sediments and lavas (greenstones), penetrated by the granite and granite gneiss and, at various localities, cut by bosses, sills, or dykes of gabbro, diorite, granodiorite, and other types of intrusives. The nickel, copper, and gold mineralization accompanied or followed the intrusion of these different rock types. The gold deposits are limited in distribution, so far as known, to the northern part of this prospecting area and occur along Manigotagan and Wanipigow rivers. These deposits have recently been described in some detail, (3) and therefore only the copper and copper-nickel deposits of the southern part of this area, along Oiseau and Maskwa rivers, will be described in this paper.

Jan 1, 1925

By P. R. Clark, M. D. Gleghorn

"IntroductionAt TransAlta Utilities Corporation's Highvale Mine, located west of Edmonton, Alberta (Fig. I and 2), dragline stripping has proved to be a practical and economical method of overburden removal and future plans have been based upon the continued use of draglines (Fig. 3) as the major stripping equipment (Williams, 1979, Nikols et al., 1986). However, long range planning has shown that the capacity of draglines alone will be exceeded in the early 1990s as mining progresses into deeper overburden cover (Tapics, 1983). Strip ratios will increase from I.3 bank m!/ t of coal in 1985to 4.5 bank m3 / t in 1995. During this period the depth of overburden will increase substantially and the areas to be mined will be characterized by weak soils including glacially displaced overburden. This increased overburden depth in relatively weak soils will make it impractical to _continue side casting by draglines without prestripping in advance. In 1983, a major investigation was initiated to determine what additional overburden removal equipment was appropriate to the Highvale operations, and recognizing the long delivery times of this major equipment. when it would be required. This paper describes studies and tests which were undertaken in 1983 and 1984 to select prestripping methods and equipment for the future operation of the mine.Previous planning studies have shown that with the current burn schedule and with the economies of progressing from low cover to high cover, as has been practiced in the past, overburden volumes will exceed the capacity of the existing draglines in the early 1990s (Fig. 4). These previous studies had placed reliance on (I tandem dragline operation for future overburden removal requirements up to a depth of 45 m throughout the Highvale Mine. New drilling together with the associated geotechnical studies and some detailed planning on the practicality of using tandem draglines, created concerns about their universal application. Even without considering geotechnical conditions there was a depth limitation to tandem dragJines and substantial prestripping would be required to achieve the ultimate depths."

Jan 1, 1987

By M. R. Julien

"The geomechanical behavior of rocksalt shows very distinctive features. The response of this most ductile of all low porosity rocks is dominated by inelastic processes that are strongly time- and historydependent. These characteristics must be taken into account when analyzing underground openings. Different constitutive models have been proposed and used for this purpose, and this paper presents the general formulation and applications of one of these. The SUVIC model relies on a unified approach with internal state variables producing mixed hardening to represent the inelastic behavior, which lead to specific solutions for plasticity and creep. The model equations have been implemented into a finite element code to perform numerical analyses. Simulations results are presented to show that this model captures essential aspects of rocksalt behavior under simple and complex laboratory testing conditions. Simulations are also conducted to analyze the response of underground openings. INTRODUCTIONPredicting the response of man-made excavations in rocksalt can be quite a challenge as it requires a reliable constitutive model to represent the material behavior. This softest of all low porosity rocks shows a highly non-linear inelastic behavior, very sensitive to history and rate effects (e.g. Senseny et al., 1993; Cristescu & Hunsche, 1997; Julien, 1999; Wittdke, 2014). The many deformation (micro) mechanisms acting locally in rocksalt make the construction of appropriate constitutive equations quite complex. Nonetheless, there have been significant progresses made over the last two decades or so; many of these developments have been included in a series of specialized Conferences Proceedings (Ghoreychi et al., 1996; Aubertin & Hardy, 1998; Cristescu et al., 2002; Wallner et al., 2007; Bérest et al., 2012)."

Jan 1, 2015