Search Documents

By Gaston Gendreau

CETTE PRÉSENTATION traitera des différentes phases des opérations de la mine du Mont-Wright depuis ses débuts jusqu'à présent. A une brève description de la géologie du gisement, suivra un exposé des méthodes d'exploitation de la mine et du genre d'équipement utilize.

Jan 1, 1977

By Z. Xiao, A. R. Laplante

"The recovery of gold by gravity from grinding circuits differs from virtually all other gravity recovery approaches in that stage (or unit) recoveries are low, typically 1 to 5%, but overall recoveries are generally in the 25 to 60% range, because individual gold particles are presented many times to the primary recovery unit. Full-scale recovery is difficult to predict from benchscale tests. Further, maximizing metallurgical recovery is generally not the primary objective, because of the more efficient downstream recovery circuit (flotation or cyanidation). In this paper, a new concept, the gravity recovery effort, is presented to assist in the design and optimization of gold gravity circuits. It is defined as the product of the circulating load treated by the primary gravity unit, the recovery of this unit, and the gold room recovery. Predicted gold recovery is linked to the recovery effort, the size distribution of gravity recoverable gold (GRG), the dimensionless retention time in the mill and the partition curve of GRG. A case study of economic optimization of the gravity recovery effort is presented. INTRODUCTIONPredicting gold gravity recovery from grinding circuits has always been a hit-and-miss exercise. The problem can be traced to the highly variable gravity recoverable gold (GRG) content of ores, high GRG circulating load, fraction of the circulating load treated, and performance of primary gravity recovery and gold room. Typical values, highs and lows are shown in Table 1."

Jan 1, 2001

By J. C. Escobedo, J. M. Almanza, A. Flores, Cortés. D. A.

Secondary aluminum dross, which has been exposed for several years to atmospheric conditions, was characterized using chemical analysis, X-ray diffraction, optical and scanning electronic microscopy, and energy-dispersive spectroscopy. Based on the characterization, a method to purify the solids is presented. This method starts with the washing of the dross in boiling water to eliminate the soluble compounds like Na and K, followed by the physical separation of the metallic aluminum by milling and screening. Finally, an acid lixiviation process is applied using three different acid solutions, HCl, HNO3, and H2SO4. The best results were obtained using HCl. The main insoluble components of the dross after lixiviation were Al, SiO2, and Al2O3. MgAl2O4, AlN, Si, and Na2Al22O3·2H20 species were also found. Based on the alumina content, the solid product could be suitable as a raw material in the manufacture of castable refractories or metal matrix composites.

Jan 1, 2005

By Margarete Kalin

"Biotechnological approaches to decommissioning of mine waste management areas are presented in the context of sustainable environmental management. Improved design of waste sites and environmental management paves the way for the application of new technological approaches. Mining wastes are better confined, effluent quantity is reduced and the quality is expected to improve in the future. The biologically mediated treatments focus on the creation of conditions inside the waste management area which lead to the confinement of the contaminants in the inactive tailings ponds and seepage collection ponds, as well as pits or other disturbed areas which were part of the operating conditions.Biogeochemical reactions lead to three fundamental water treatment steps mediated biogeochemically , alterations in chemistry which lead to formation of particles, which then have to flocculate and be assisted to collect in the bottom of the ponds. Microbially active sediments are installed to assist particulate formation and serve as sinks for metals. In deeper sediment strata, stable forms of metals are created. Biological polishing is used to collect the particulates and relegate them to the sediment. Examples will be given of the application of these processes, to waste rock piles, open pits and tailings ponds. This paper attempts to show that, through the integration of applied biotechnological advances and the application of new approaches to decommissioning, reductions of environmental impacts by mining are possible. * Note: this paper has been presented at the 13th Annual Meeting of BIOMINETIntroductionThe role of biotechnology in decommissioning of mining waste management areas should be placed in the context of sustainable development. The concept of sustainable development as defined by the Brundtland Commission (1987) for the restoration/ reclamation of mining operations could be translated as follows: The increasing demand for the resources by the world population must be met in a manner which does not compromise the earth's environment over the long term (Brooks et al., 1995)."

Jan 1, 1998

By Torsten Zeller

Due to the increasing worldwide demand for raw materials and the resulting rise in commodity prices more expensive processing that is able to utilize complex ores becomes economically viable. This and increasing ecological awareness is why the interest in recycling and urban mining is steadily growing in Germany. In addition to that; landfills do also contain elements, which were not targeted over the period, when they were being accumulated. Examples are rare earths, indium, gallium, cadmium, arsenic, selenium and tellurium. Also copper, zinc and lead, the target components of ancient mining, can be obtained due to more effective processing and smelting technologies. Funding by the German Federal Ministry for Education and Research, entitled "r³ ? Strategic Metals and Minerals ? Innovative Technologies for Resource Efficiency" also indicates the high level of strategic interest. It is against this background that the research project "Exploitation of the Raw Material Potential of Mining and Metallurgical Tips in Respect of Sustainability as Exemplified in the West Harz Mountains (ROBEHA)" has been implemented. A major concern of this project is the possible transfer of results to landfills in other areas. Therefore the development of an expert system based on the innovative processing methods and a method manual for urban mining are the central components of the investigation. This will provide an important contribution to the cost optimization of ensuing urban mining projects. To ensure the success of landfill mining projects it is necessary to record the composition and quality of the deposits accurately. Also the environmental impact caused by landfill mining and changes in the natural and cultural landscape will be considered in a multicriteria evaluation method. Depending on their origin the tips are divided into the categories mining, processing, and smelting. The content of a landfill and thus the economic potential in terms of urban mining is dependent on the type and composition of the deposits (host rock, gangue, and ore mineral), the available processing and smelting technology, and the target components at the time of mining. Zinc, for example, was not been processed until the 19th century, when it gained attention as being material of economic importance. After such knowledge about a landfill is obtained the decision for further investigations can be made. For a total of 158 landfills in the Harz Mountains, both the volume and the approximate contents of copper, zinc, and lead has been estimated for the different types of tips within past research projects. Based on the prices of the London Metal Exchange (LME) and a euro/dollar exchange rate of 0.76 (as of 03/05/2012) and assuming a minimum density of ? ? 1.5 t/m³ a average value of 1.6 billion ? in copper, zinc, and lead can be obtained. Although only these three metals are considered in this first estimate, it demonstrates the potential of landfill mining and the need for further research. KEYWORDS Urban Mining,

Aug 1, 2013

By Norman R. Paterson

"Under certain conditions useful gravity information of a reconnaissance nature can be obtained with-out measuring elevations by spirit level surveys on the ground. Gravity surveys can become part of a practical exploration program where high cost and slow progress previously hindered their utility. The advantages of the new elevation procedures are realized mainly in remote areas, in areas where ground transportation is slow and difficult and on surveys where the station spacing is large in comparison with the distance of the average optimum level shot. To utilize the advantages, transportation by helicopter or light plane is usually necessary. Methods of obtaining elevation control without leveling include: barometric altimeter survey; photogram-metric -APR spot determinations; methods involving the measurement of gravity gradients. The accuracies of these methods have been tested and compared with the normal accuracy of level surveys. It is felt that each method has its place in reconnaissance gravity work, particularly in the open areas of Northern Canada."

Jan 1, 1960

By A. G. Doll

"Multi-stage crushing plants, including high pressure grinding roll (HPGR) circuits, require more materials handling equipment than SAG and ball mill circuits. A temptation exists to neglect the energy consumption of materials handling when doing desktop comparisons of HPGR versus SAG milling circuits because estimation of materials handling power requirements can demand significant general arrangement drafting that is not available when performing preliminary scoping or ""desktop"" studies.The largest component of materials handling power is consumed by conveyors when lifting material between stages of crushing, meaning that a simple potential energy model can be used to evaluate conveying specific power consumption. This potential energy consumption for conveying can then be factored to provide overall materials handling specific energy consumption suitable for desktop studies of HPGR and other multi-stage crushing circuits. The technique also permits different crushing circuit flowsheets to be evaluated, at a preliminary level, by simply counting the number of times a conveyor must ""lift"" ore from ground level up to a bin or other equipment mounted up high.INTRODUCTIONTrade-off studies of multi-stage crushing plants involving high pressure grinding rolls (HPGRs) versus semi-autogenous grinding (SAG) mill circuits typically focus on the operating cost savings of crushing plants versus the capital cost savings of SAG mill plants. Very high-level (or desktop) studies of this type do not include a great deal of engineering work, meaning that the details (and costs) of ancillary systems are often not captured when doing the comparisons. The more complicated nature of the multistage crushing plants means there are more ancillary systems than a SAG mill plant, risking a skewed analysis of the operating costs, benefiting the HPGR option.One of the ancillary systems that may be overlooked is the more complicated conveying systems inherent in multi-stage crushing plants. Due to the mass of material being handled in large mining operations, these conveyors become a significant portion of the operating costs. A simple way to estimate the specific energy consumption of conveying systems without requiring engineering drawings and a site layout would allow high-level studies to capture this operating cost."

Jan 1, 2015

By A. C. Stevenson

"There are many critical application issues that affect all AC drives, but there are several that are absolutely mandatory for pulse width modulated (PWM) AC drives. If these rules are not followed, the drive system will have insulation, bearing EMI or noise problems. Pulse Width Output VoltageFigure 1 shows the output current of a typical pulse width modulated (PWM) drive. This is, of course, not a clean sine wave thus will have a lot of very significant harmonics. In fact, the harmonic spectrum is directly related to multiples of the carrier switching frequency plus side bands related to the basic output frequency. A typical spectrum for a PWM source bridge switching at 5 kHz is shown in Figure 2. Notice that the spectrum has multiples of the 5 kHz switching frequency and the number of side bands gets larger as the harmonic number increases.IGBT Switching TransientsWhenever we have PWM inverter switching, voltage transients are formed that propagate (usually at about half the speed of light) down the power cables to the motor just like in a radio frequency transmission line. If we do not terminate these transmission lines (motor cables) properly, the voltage pulses will be reflected when they reach the motor end and will be transiently increased up to twice their original amplitude.This transient voltage rise, shown in Figure 3, is important for three reasons:1. Insulation Voltage Stress — Higher voltage stress in the motor connecting cables and motor insulation will lead to a shorter insulation lifetime. If any of the voltage transient peaks exceed the insulation corona discharge level (partial discharge level), the insulation will gradually degrade with each voltage pulse. When it has been sufficiently degraded, it will then fail.Most new “inverter rated” motors have triple layer insulation which has a 1600 to 2000 volt partial discharge level. This will make them suitable to withstand the double voltage peak transient from a 600 volt inverter. It is wise to make sure of this fact, since a “standard” induction motor will only withstand about 1200 volts. Use of a standard motor in this application would shorten its life drastically. This can sometimes be as little as a matter of hours."

Jan 1, 2000

By J. E. Gill

Discovered in 1952, the deposits have been explored by diamond drilling on and near a group of islands in lake Nipissing and from under-ground workings. The ore mineral is a uranian pyrochlore. It occurs in breccia zones in association with calcite, apatite, a?cmite, feldsiiars, biotite, magnetite, sulphides, and fluorite in varying amounts. The pyrochlore concentrations occur in a steeply-dipping gneiss series with some crystalline limestone. Trends indicate a ring structure 114 miles in diameter. The main ore zone shows evidence of repeated brecciation and a succession of replacements .giving rise to a complex of rock types. Pegmatite and lamprophyre dykes cut the ore as do calcite-fluorite veins and later faults with small displacements. Columbium and uranium occur al-most exclusively in pyrochlore, but the proportions vary. There is no tantalum and only small amounts of titanium.

Jan 1, 1957

By J. Olson

"A model was developed to use near-infrared (NIR) analysis of pulverized ore samples to estimate the recoverable gold content for ores from the Barrick Cortez Hills underground mine. Current routing practices use a ratio of the cyanide soluble gold content and fire assayed gold (CN/FA) to classify ores as oxide or refractory. Prediction accuracy of the NIR model was equivalent to the CN/FA ratio. Prediction accuracy was improved by combining the CN/FA ratio and the NIR spectra. Bootstrap validation estimates the root-mean-square error to be 9.92% with an estimated r-squared value of 0.893. This model will allow more accurate estimates of the variability in recoverable gold content throughout this mine. These data will aid in building an improved geo-metallurgical model or in making better informed routing decisions during the production cycle.INTRODUCTION The contained gold of an ore available for cyanidation is often related to subtle variations in the mineralogy. It is difficult and expensive to collect enough mineralogical information in order to predict how the variable mineralogy will impact the metallurgical results and project economics throughout the life of the mine or mill. Near-infrared spectroscopy may be an effective tool to rapidly and inexpensively collect discrete, quantitative mineralogical data for minerals that contain transition metal oxides, metal sulfides with semi-conduction properties, rare earth metals, and some chemical groups having di-pole covalent bonds such as carbonates, sulfates, and various types of clays (Hunt, 1977). Near-infrared spectroscopy can be a powerful tool for geo-metallurgical characterization of deposits where the presence of these minerals has direct or indirect relationships to metallurgical results such as grindability, regent consumption, or recovery. Near infrared spectroscopy is a rapid analysis that measures the intensity of reflected light in the near-infrared spectrum. The ranges for the ASD-Panalytical units used in this study extend through the visible spectrum and into part of the UV spectrum, reporting reflection by wavelength from between 350 nm to 2500 nm. Absorption peaks visible in this range are a result of interactions with outer valence elections or chemical bonds. The location and intensity of the peaks vary depending on the chemical composition and crystal structure of a solid indicating the presence and abundance certain minerals (Hunt, 1977; Clark, 1984)."

Jan 1, 2017

By E. Van Den Neste

A concise historical review is given of the Overpelt plant and the general principles of zinc hydrometallurgy are briefly outlined, together with a description of the new electrolytic zinc plant ore roasting process and, more particularly, the original Overpelt roasting process. A detailed description of the flowsheet of the zinc electrowinning plant, .with an annual capacity of 100,000 t, successfully put into operation in May 1974, is given. The treatment of the residues is performed following the goethite process ; the purification is continuous in two steps; the tank house is equipped with cells containing jumbo cathodes; the handling and stripping of the cathodes is fully mechanized. Concluding the description, some metallurgical and other features of the project are explained in detail.

Jan 1, 1977

By D. F. Sherwin

"THE AREA which is described in this paper (Fig. 1) includes the continental margin of eastern Canada extending from the Gulf of Maine to the north edge of the Grand Banks, which, including the continental shelf, slope and rise, comprises an area of about 600,000 square miles. The paper is intended to give a background of the geological setting of this region in the context of its ultimate potential for oil and gas reserves in close proximity to the Nova Scotia energy market.HISTORY OF EXPLORATIONThe history of geological exploration of this area really began in 1878, when U.S. fishing boats brought back samples of rock recovered in trawls from their expeditions to the long-famous fishing banks off Canada's East Coast. Tertiary and Cretaceous fossils recovered from these samples indicated that the eastern Canadian continental shelf was actually the submerged northern extension of the Atlantic Coastal Plain."

Jan 1, 1972

By Paul Delottinville, Maynard Hall, Henry Hillier

"An expert system application for supervisory control and optimization of the indurating process at the Iron Ore Company of Canada (IOCC) has been developed and installed in closed-loop. Prior to the installation of the expert system, the indurating machine was rebuilt and the instrumentation revamped. A Foxboro I/A Distributed Control System (DCS) was installed for regulatory control, and a new control strategy configured. The modernization of the regulatory control has resulted in significant improvement in both production rate and product quality. Expert system control was implemented in September 1996. Preliminary indications are that the expert system has further improved the consistency of product quality, enhanced fuel efficiency and increased productivity. The expert system considers both wet and dry sections of the circuit, and its optimization scheme is driven by pellet tumble index and compression strength. Statistical Process Control (SPC) rules were implemented in the expert system as part of the quality analysis and control scheme. The expert system application was developed and delivered using the Comdale Expert Optimizer (CEO), and has been in continuous closed-loop control since its installation. The system development and implementation is described, and preliminary benefits are presented..... IntroductionIn early 1996 the Iron Ore Company of Canada (IOCC) contracted Comdale Technologies of Toronto to develop and implement a real-time expert system for optimizing the indurating pelletizing furnace at our plant location in Labrador City, Newfoundland.The decision to install the expert system has been timely. Like many other resource-based industries in increasingly competitive markets, IOCC recognizes the need to find ways to improve the efficiency of our production process and ensure that product quality is maintained at the highest levels. With the Labrador City plant producing 11 million tons of iron ore pellets annually, implementing the best technology solutions to meet these objectives is critical."

Jan 1, 1998

By A. E. Wraith, J. Protheroe Jones, P. J. Mackey

INTRODUCTION When Victoria became queen in 1837, that technical wonder of the 19th century—electricity— had progressed from being an exciting physical curiosity and was now a field of intense scientific investigation, invention and application. Its role in electrochemistry had been brilliantly quantified by Faraday in 1833–1834, and his earlier discoveries in electro-magnetism were to lay the foundations of electricity generation and the electric motor. In this age of electrical experiment, silver electro-plating emerged as a popular decorative art, at first using batteries to provide the deposition current, superseded by dynamos in the early 1840s. The decorative chemical and electroplating of precious metals was largely pioneered in England by the firm of G.R. Elkington and Co., founded in Birmingham by George Richards Elkington (1801–1865) in 1832, and protected by a series of patents which helped the company establish a leading position in the new field of ‘electrometallurgy’. In the same decade, the technique of electrotyping emerged, the first application of electro- forming by electrolytic deposition. Simultaneously invented by Spenser in England and Jakobi in Russia, but generally claimed for Jakobi, electrotyping involved plating a thick copper layer on to an electrically conducting mould wall embossed or incised with a pattern or profile which would consequently be replicated on the copper deposit—essentially a method of casting by electro-deposition with the mould wall as cathode. Woolrich’s invention of the low voltage magneto-dynamo in 1842 eliminated the need for batteries as a continuous source of deposition power, opening up the possibility of making more massive electroplated deposits, and by the mid-point of Victoria’s reign in 1869, the work of Wilde, Wheatstone and Siemens had produced the self-excited electro-dynamo, capable of higher voltages and yet greater deposition power. In this early Victorian period copper was extracted and refined by methods which had developed step-by-step over many decades. Only relatively rich copper ores containing more than, say, 6% Cu were economically useful, and the final copper product was far from pure. Copper production in Britain was located principally in the Swansea area of South Wales, based upon the ‘Welsh process’ of reverberatory batch smelting and refining, using locally mined coal and ore imported from Cornwall and elsewhere. Silver was an important by-product. Much of the output was exported and South Wales remained a principal supplier to the world copper market until the 1890s. It was here at Pembrey, a few miles west of Llanelli, that a new primary copper smelter was stablished in 1849 under the name Mason and Elkington, arguably to supply the Elkington company’s market for electrotype products.

Jan 1, 2019

By Hani S. Mitri

Overhand cut-and-fill mining of narrow vein orebodies inevitably leads to the creation of horizontal pillars. As the thickness of the overlying crown pillar diminishes, stresses build up in the pillar. More often than not, this situation causes an increased level of seismicity and possible pillar burst. One well-known strategy to reduce the hazard of crown and sill pillar burst in cut-and-fill vein mining is that of destress blasting. The paper first reviews the methods used for the monitoring and assessment of potential pillar burst in narrow vein cut-and-fill mining. The influence of horizontal stress, mine depth and pillar thickness on stress build-up in the crown pillar is examined through a characteristic narrow vein numerical model. The paper then presents, with reference to three mine case studies, the benefits of destress blasting and the factors affecting its success as a ground control technique.

Oct 1, 2001

By E. S. Moore

DEEP oxidation and-secondary enrichment of ore deposits, although so important in many parts of the world, are comparatively rare in the Canadian shield. Intensive glaciation during the Pleistocene epoch accounts for their rarity. Glaciation has cost Canada much in the destruction of not only enriched ore deposits, but placers that must have been developed near our numerous gold deposits during the long period of weathering that pre-ceded the Pleistocene. There seems to be a very common misconception regarding the average depth of rock that has been removed from the shield by glaciers. These bodies of ice are usually given credit for the removal of the greater portion of the thousands of feet of rock that we know has been eroded from this large area since Precambrian time. As a matter of fact, the average thickness of solid rock removed can be measured in tens rather than even hundreds of feet, although very deep erosion has resulted in some sections where the glacial ice has been constricted in depressions, such as deep valleys and lake basins. On the other hand, there are few areas within the shield where the glaciers have not disturbed practically all of the mantle rock and some feet of the underlying bed-rock. The chances of finding deeply oxidized cappings and enriched ore deposits are therefore comparatively few and these have been found chiefly where favourable structural and topographic conditions for their formation and preservation have existed. Faulting has been responsible for several of these deposits, and easily decomposed rocks, such as. sulphides and carbonates, have been very important factors. Topographic features, such as high and resistant hills, favourably situated with respect to the ore deposits have, in a few cases, played a part in providing protection from glacial erosion and in furnishing head for the descent of surface waters. At least four cases of oxidation to depths quite abnormal in the Canadian shield have so far been found in Ontario. These are the Helen and Josephine iron mines in the Michipicoten district, the Keeley silver mine in South Lor-rain, and the Ross gold mine in Hislop township, Cochrane district. A deeply oxidized zinc deposit of unusual interest occurs in the Precambrian rocks in New York State, not far from the Canadian border, and there arc the well-known iron deposits in the Lake Superior region of the United States.

Jan 1, 1938

By Blair Hrabi

Introduction; ?Risks Associated with the Resource Estimation Process; ?Limitations of Available Data; ?Geological and Structural Control of Mineralization Trends; ?Recognizing Multiple Mineralization Controls and Complex Trends; ?Accurate Geodomaining; ?Conclusions.

May 1, 2013

By Vu Van Dong

Resource estimation is the science of determining the amount and quality of a given material in the ground that has the potential to be mined at a profit. This is because during this time computers have become more widely available and more powerful and software packages have become more comprehensive and user friendly. Over the past three years The Mining Geology Company with the support from Vinacomin Group has developed the Coal Geological Modelling and Reserve Estimation ? VMG system. The VMG system enables the geological and mining engineer to start at the reserve estimation for the mine design and planning. The VMG system enables the national and international standards (NI43-101, CIM-Canada; SAMREC Code, Africa, and JORC Code, Australia) and user friendly with menu driven thereby permitting the engineer with minimal computer training to rapidly learn and utilize the system. Geological and mining data input through digitized map files and drill-holes information files stored in the database that is an integral part of the VMG system with the main function for collection, validation, and recording, storing and processing of data will include both ?primary? (observation and measurement) and ?interpreted? data. It is recommend that data be stored digitally, using a documented, standard format and a reliable storage medium that allows for easy and complete retrieval of the data. The coal reserve estimation through standard polygon methods with the increased use of these mathematical techniques (geometrical modelling, geostatistical method, least square method, ?) over the last ten years corresponds, to some degree, to a decrease in both the amount of the coal deposit mapping and, in particular, coal seam structural interpretation and modelling, and permit rapidly evaluation of coal seam and overburden quality and quantity. The understanding of the relationship between the coal mineralization of interest and the likely related complicate geological processes and structure that govern its emplacement and geometry within the geological framework is essential to the establishment of the geological controls for coal mineralization. System outputs includes: drillholes summary reports, stratigraphy, cross-sections, isopach maps, structure, contour maps, premining and post mining topography maps, and 3D perspective view on coal seam structure.

Oct 1, 2009

By R. S. Jr. Stronach

"IntroductionThe property of Campbell Red Lake Mines, Limited, is in Balmer township, Red Lake area, Patricia portion of Kenora district, Ontario. It consists of a group of twelve claims which had been staked and re-staked a number of times before George W. and Colin A. Campbell staked them in 1944. Messrs. Brewis and White incorporated Campbell Red Lake Mines, Limited, in July, 1944, to acquire these claims from the Campbell brothers, and in November of the same year re-assigned their option on the controlling interest of the treasury shares to the Dome Exploration Company (Quebec), Limited, a wholly owned subsidiary of Dome Mines, Limited.A long known exposure of sulphides on the northeasterly portion of the property, which returned low gold assays, on sampling, was the only showing of interest at this time. However, Dr. H. C. Horwood's report and map of the district had recently been published and favourable structure W3.S indicated in Balmer township. It was on the strength of this showing and Dr. Horwood's report that Dome Exploration became interested in the property.Between. January, 1945, and April, 1946, a diamond drilling programme was carried out, with completion of sixty-one holes. Five holes proved the surface showing to hold no commercial interest, so routine cross-sectioning of the property from north to south was started. The fourth hole of the series returned excellent ore intersections and from that time on the programme changed to one of extending these values. The final results of the drilling showed that what is now known as the A zone has a continuous length of some 1,200 feet, a width of 4½ feet, and an overall grade of about 0.5 oz. gold per ton. There were many other intersections of ore grade outside this A zone which could not be successfully correlated .at that time, but underground work has opened many of them. It may be said here that practically all the work to date has been confined to the southeast claims of the property."

Jan 1, 1950

By S. Kelebek, B. Nanthakumar

ABSTRACT The sensitivity of sulphide minerals towards oxidation depends on the mineralogical makeup and nature of sulphide ores. This paper focuses on chalcopyrite behaviour in a nickel-copper sulphide- ore matrix that was aged in the mine-site stockpiles. Results of collectorless, collector-induced flotation and recovery by size are presented following a discussion of XPS analysis that was used to gain insight into oxidative alteration of chalcopyrite’s surface chemistry. Chalcopyrite maintains its high flotation activity despite exposure to weeks of oxidative conditions. It is concluded that chalcopyrite is quite tolerant to stockpile oxidation due to various factors related to alteration of its surface chemistry.

Jan 1, 2012