Search Documents

By Robert B. Parsons

"The Department of Finance introduced draft amendments to the resource allowance regulations on July 23, 1992 that effectively nullify the decision in the Gulf Canada Limited case. Prior to the amendments it appeared that only ""directly"" related general and administrative, capital cost allowance and scientific research expenditures had to be deducted from resource profits. Now ancillary expenditures are required to be deducted. Consequently, the ability of taxpayers to claim the resource allowance is curtailed.IntroductionOn October 25, 1990 it was almost certain that taxable mines were going to get a break. The Federal Court-Trial Division had just decided in Gulf Canada Limited's favour to allow it to claim resource related tax benefits larger than what Revenue Canada evidently wished. Revenue Canada appealed first to the Federal Court of Appeal and then to the Supreme Court of Canada. On January 10, 1992 the Federal Court of Appeal agreed with the Federal Court decision and on July 2, 1992the Supreme Court declined to hear any further appeal. A mere three weeks later, on July 23, 1992, the Department of Finance issued draft ""clarifying"" measures to amend the calculation of the resource allowance. These measures effectively nullify the benefits that arose under the decisions of the Federal Court."

Jan 1, 1992

By Orlando Rojas, Javier Pizarro, Romke Kuyvenhoven, Francisco Soto

"The concept of geometallurgy has been extensively mentioned and used in the mining industry in the past years. However, each mining firm has a different understanding of what geometallurgy means, and its actual value varies significantly from site to site. Even in the case of properly constructed geometallurgical models, it is fairly common to observe a sub-utilization of the model in the actual operation, because of its low production forecasting capability on the short term. This disconnect between the geometallurgical model and operations is typically caused by a lack of tuning between the original model and the actual plant operation. Also, the absence of procedures and other standards for reconciliation, affects the confidence and the predictive quality of the model. The geometallurgical model should consist of three different levels: (I) adequate capture of information, (II) data analysis and modelling, and (III) development of the block model. Once the geometallurgical in-situ model is finalized, a process model should be developed of the plant at industrial scale, in order to scale up the in-situ geometallurgical parameters from their base or standard condition, to the actual operating reality of the plant. Finally, the stage of reconciliation will close this process, assuring that any deviation between the geometallurgical model and the actual plant operation is not due to lack of tuning, but due to operational issues such as unattended maintenance requirements or poor process control in the operation. The methodology as described in this paper has been applied at several large mining sites in Chile. The paper presents the characteristics of the proposed methodology, and quantitatively describes its benefits with examples from actual operations.INTRODUCTIONIt probably is fair to say that geometallurgy became widely used in greenfield projects in the Andes region during the mining boom of the 90’s, when massive orebodies were studied and developed, and upfront metallurgical characterisation proved its use for accurate economic evaluation including estimates of plant throughput, energy consumption, final product quality and overall recovery. A few examples of such greenfield studies for concentrator plants in the 90’s are Minera Los Pelambres (Antofagasta Minerals, Chile), Minera Escondida, Laguna Seca (BHP Billiton, Chile), and Rio Blanco (then Montterrico Metals, Peru). Large size hydrometallurgical operations such as Cerro Colorado, Quebrada Blanca and Lomas Bayas (all in Chile), also recognised early on the importance and value of relating ore mineralogy, geological characterisation and metallurgical behaviour."

Jan 1, 2016

By Robert D. Irvine

"Enhanced concern for protection of the environment and attendant actions by environ-mental regulatory authorities in support of this concern are influencing, to varying degrees, the demand and supply of a range of industrial minerals in a number of jurisdictions. These influences take a variety of forms.In this paper, the author seeks to delineate certain broad trends which are occurring relative to industrial minerals and the environment and then, through a series of examples, to outline opportunities, developments, and impacts respecting a number of industrial minerals produced and consumed in Canada and the United States."

Jan 1, 1996

By N. Dufresne

"The evolution of mining methods at Brunswick Mining and Smelting shows that, in the case of a large deposit, technology must adapt itself to changing conditions. As problems are encountered, management must modify their approach if they hope to meet production quotas. This search for new and better ways started with the opening of the No. 12 orebody and is still going on today.From large-scale open stoping, the Brunswick Mining and Smelting operation went to transversal cut-and-fill, then to longitudinal cut-and-fill, which is the main mining method now employed. However, to solve certain problems experimenting with Avoca methods was initiated. Rebar grouting and prepinning have also made significant contributions toward securing relatively poor ground in the hanging wall and holding badly fractured backs in wide stoping areas. Introduction In 1952, M.J. Boylen had incorporated Brunswick Mining and Smelting Corporation Limited to develop his recently found No.6 and No. 12 orebodies near Bathurst, New Brunswick. Between 1953 and 1957, St. Joseph Lead Company was brought in to try and initiate mining . During those years, St. Joseph Lead sunk two shafts at No. 12-No. 1 to 425 feet below surface and No.2 to 982 feet. They also developed the 200 and 350 levels to sample the ore at depth and operated a 100-tpd pilot plant at the No.6 mine. However, due to low recoveries and depressed metal prices. the project was shut down in 1957.A group including M.J. Boylen. K.C. Irving. Maritime Mining Corporation and Patino Corporation reacquired the property from St. Joseph Lead Company in 1961. New financing was arranged involving La Societe Generale des Minerais, S.A . of Belgium and Engineering Consultants Limited of Saint John. New Brunswick. During the years 1962 and 1963, construction of surface and underground facilities progressed rapidly."

Jan 1, 1981

By R. D. Brown

The first step in achieving a rationalization of Canada's crazy patch-work quilt of mining taxes and policies was achieved with the release last November of a major federal-provincial report on the taxation of the Canadian mining industry. The Report, prepared by a group of federal and provincial civil servants, sets out a concise and informative discussion of the major taxation and incentive issues facing the mining industry, and puts forward major recommendations for more rational and moderate taxation policies. It will be considered by federal and provincial Finance and Resource Ministers for possible action by the respective governments. The Report was prepared in response to a directive from the federal and provincial First Ministers in February 1978 to review the federal and provincial taxation of the resource areas. Although the Report is more successful in identifying problems rather than concrete solutions, and reflects some continuing differences of opinion between the governments involved, it does represent an important first step in a comprehensive review of our resource tax policies. This article summarizes the Report, which is some sixty pages in length. Although a detailed discussion of it is beyond the scope of this article, the report itself is recommended reading for those concerned about the current state of the Canadian mining industry.

Jan 1, 1979

ABSTRACT The inevitable uncertainty in modelling spatial variables decreases as more data become available. This reduction depends on the properties of the variable being modelled. Spatially continuous variables show less uncertainty for a given spacing than erratic variables. A geostatistical simulation based approach is developed to quantify the relationship between uncertainty and data spacing. Reference realizations are sampled to condition additional realizations and quantify uncertainty. The procedure is automated, making it straightforward to consider sensitivity and different geological domains. A case study of the relationship between uncertainty and data spacing for net oil sands thickness data from northern Alberta is presented. _ KEYWORDS Simulation, Sampling,

Jan 1, 2013

By R. Barbaroux, J. -M. Lalancette, D. Lemieux, K. Nasrallah, G. Garcia Curiel

"Arsenic released from the lithosphere by mining and metallurgical activities is a growing global environmental concern. Dundee sustainable technologies (“DST”) has developed a processing technology to sequester arsenic by means of vitrification. This method can effectively sequester arsenic trioxide without the need to oxidize from As (III) to As (V). Arsenic oxide is incorporated within a silica glass matrix that is stable as per the Toxicity Leaching Characteristic Procedure (“TCLP”) or EPA Method 1311. In this paper, the conventional treatment of arsenopyrite, commonly referred to as “two-stage roasting”, is discussed along with the options traditionally available for the remediation of the arsenic trioxide by-product. The drawbacks limiting the adoption of this processing flowsheet are discussed and a new processing route is presented for the treatment of arsenopyrite. This new flowsheet outputs an auriferous aluminosilicate highly amenable to gold extraction (> 96%) while eliminating the sulfur dioxide production associated with the second-stage roasting of pyrrhotite and ultimately uses vitrification as a definitive sequestration solution to arsenic trioxide.INTRODUCTION Faced with the depletion of conventional gold ores, the gold industry has witnessed a trend towards the exploitation of arsenical deposits. Arsenic is a naturally occurring metalloid often found in mineralogical association with gold. Many northern Canadian regions, from the Northwest Territories to Northern Manitoba, Northern Ontario and the Abitibi region are facing significant arsenic challenges. Projects are deemed uneconomic or prevented from going into operations due to the costs associated with handling arsenic material and there are penalties imposed to complex concentrates by smelters. In addition, Canadian mining operations have left an environmental legacy of gold tailings with grades typically of up to 9 grams per tonne with no processing solution as they also contain significant arsenic contamination at grades of up to 20%. Table 1 presents a list of Canadian deposits known to contain arsenic."

Jan 1, 2017

By J. Guha, R. Kanwar, G. Archambault, A. Tremblay

The Copper Rand Cu-Au deposit lies within a shear zone which strikes N50-60W and dips steeply southward (50°-55°) and extends over 1. 5 km with a thickness which varies form 350 to 425 metres. Mineralization, inside the shear zone, is structurally controlled by a dilation mechanism which can be explained by a fracture dilatancy model. The principle of this model involves the mechanics of overriding of irregular planes and surfaces of faults and schistosities, These structures are characteristic features of the Copper Rand shear zone. A structural analysis of the shear zone has been carried out to establish relations between the different structures within the shear zone and their evolution with the development of the shear zone. A geomechanical interpretation of the Copper Rand shear zone explains the formation of internal structures such as faults, schistosities and microstructure during the shearing. This interpretation confirms Ramsay's theoretical model on the geomechanical evolutuion of shear zone development, and the experimental work of Morgenstern-Tchalenko on the simulation of shear zones in clay models. The geomechanical interpretation of the shear zone demonstrates that at the onset, subsidiary fracture patterns are developed in second order faults in the following sequence. At peak strength Riedel shears ( R and R') are formed which propagate outside the strength, restraint (P) shears are developed in the thrust attitude within the shear zones. Principal displacement shears (D) develop toward residual strength in the direction of movement. Shear lenses are formed by the interaction of these shear discontinuities and these facilitate the formation of schis tosi ties with the continuation of the shear displacement within the main shear zone. While the main shear zone and the P and D shears within the main shear zone were in continual movement, the Rand R' structures, once formed, retained a simple fracture pattern and moved little outside the shear limits in comparison to the main shear zone. Parts of these structures inside the shear zone were reactivated by subsequent movements and deformed into folds to account for the present attitudes of the HW-1 and HW-2 and HW-3 structures. This geomechanical model for the shear zone with its subsidiary structures (R, R', P and D shears) is also applied on a larger scale to the Dore Lake shear belt and explains the different structures accompanying it. The initial development of the WNW shears (most are ore deposits) was followed by the subsidiary structures of the Dore Lake shear in a north-south stress field and is well defined by the movements characteristic of the different structures. It is concluded that the Dore Lake shear cannot be the prolongation of the McKenzie Narrows shear but it seems that this prolongation relates to the Henderson-Portage shear zone.

Jan 1, 1984

By M. Zavvari

Flotation, as with most engineering disciplines, involves testwork. Commonly this means going from lab scale to pilot scale to industrial scale. It is important to conduct tests to identify key parameters and to optimize even at the lab scale. To reduce the number of tests while maximizing the information, it is necessary to use Design of Experiment and Statistical Analysis. In this communication Fractional Factorial Design was used to identify the effect of 7 main factors on barite flotation recovery from jig gravity tailings at the Dorrin Kashan operation. The factors include: pH, collector and depressant dosage, impeller speed (RPM), pulp dilution, particle size and flotation time. By analysis of the output with Minitab software all factors were shown to have an effect. Among the factors, pH and flotation time have an interaction effect but the others have wise effect as an interaction effect and main effect. Finally, reliability tests at pH= 9, RPM= 1000, collector 1 000g/ton, depressant l 750g/ton, particle size 90 µm, flotation time 90 s, pulp dilution 23 % solids, the optimum level of each factor, were done. At the optimum level a barite concentrate with average specific gravity 4.308 g/cm3, average grade 93.72% and average recovery 90.04% was produced from the jig tail.

Jan 1, 2009

By C. Xiao, F. Mohamm, A. Borsoi

"Nitrogen compounds produced by cyanide destruction and/or blasting are often a cause of concern for environmental compliance and at times, for water re-use in metallurgical circuits. Natural attenuation in tailings ponds and wetlands is not always sufficient to ensure compliance and/or achievement of overall water management objectives. This paper provides a general overview of active treatment methods for nitrogen management followed by an investigation of selective adsorption combined with electro-oxidation as the potential treatment method for thiocyanate. Results from bench scale treatability study are presented. The concept of holistic assessment of nitrogen management at mine sites using Risk Adjusted Life Cycle Cost is introduced and discussed in the context of gold mining operations using sodium cyanide.INTRODUCTION Unlike metals, nitrogen compounds present in mine waters originate entirely from anthropogenic sources rather than mineral deposits. Table 1 summarizes the main sources of nitrogen compounds reporting to mine wastewater.The best management practice related to the use of ANFO involves minimizing contact between ANFO and water, control and monitoring of blasting to reduce the occurrence of misfires, and reducing the consumption of blasting reagents for a given ore body. The most common practice for the management of NaCN is the incorporation of cyanide destruction in the metallurgical flowsheet and the use of tailings impoundments and holding ponds for natural attenuation of cyanide destruction residues such as NH4-N and CNO. At most mine sites there is no active management of NO3-N and SCN in wastewater. While current practices have produced satisfactory results, new enhanced methods to manage nitrogen compounds at mines are needed due to: 1) Increased scrutiny over the adverse effects of nitrogen compounds released into the environment; 2) New effluent standards; and 3) The shift away from wet tailings towards dry stack systems resulting in diminished natural attenuation and dilution of nitrogen residues prior to effluent discharge or water re-use in mineral processing."

Jan 1, 2017

By Xuanxue Mo, Zengqian Hou

"Abstract -Yidun Island Arc in Sanjiang Region is one of the important Kuroko-type volcano­ genic massive sulfide deposits (VMS) districts in southwestern China. Tectonically, the region is situated in the eastern portion of the Tethys orogenic belt, and is a late Triassic extensional island-arc. The island-arc underwent earlier arc construction, intra-arc rifting, later arc construction and back­ arc spreading during its evolution and formed a complete trench-arc-basin system, i.e., the Ganzi­ Litang suture zone, forearc basin, outer arc, intra-arc rifting zone, inner arc and back-arc basin from east to west across the island-arc.Kuroko-type VMS deposits and occurrences discovered so far are limited to within the intra-arc rifting zone of the Yidun Island Arc and tend to occur in groups or clusters distributed in separate fault­ bound basins; e.g., Zengke, Gacun and Xiangcheng basins, in which submarine volcanic rocks, especially bimodal volcanic suites, were extensively developed. The VMS deposits formed in the waning stages of volcanic eruption in the late Triassic and are hosted in the uppermost section of acidic volcanic rocks (rhyolitic-dacitic) within a bimodal suite. The orebodies are associated with these host rocks: rhyolitic-dacitic pyroclastic rocks and exhalites and chemical sedimentary rocks.Ali VMS deposits in Sanjiang are of the Zn-Pb-Cu type. The architecture of the deposits is two­fold, consisting of concordant lenses and layers of massive sulfides and an underlying discordant stockwork. Ali deposits show metal zoning. The hydrothermal alteration related to mineralization is strong and asyrnmetrical, and is found dominantly within the stockwork zone and host rocks surrounding the ores. There are two alteration patterns: (1) chloritization - sericitization - silicification from outer sides to core of the alteration pipe; and (2) silicification + sericitization - silicification + carbonate from the lower to upper part of the alteration pipe_The mineralization temperatures of ore-forming fluids vary in the range 200°C to 335°C. Thermal evolution of the fluids displays temperature profiles that first increase and then decrease with progression of mineralization processes. The majority of black-ore minerais (Groups I and II) formed during intensifying stages of hydrothermal activity, and the majority of serni-yellow-ore minerals (Group III) formed during a thermal maximum . There followed the formation of fine-grained black-ore minerals (Group IV), which interacted with barite layers during decreasing temperature phases.Oxygen and hydrogen isotope studies show that the sources of ore-forming fluids for the Kuroko­ type VMS deposits are two-fold: seawater and magmatic hydrothermal solutions, represented by the Kuroko deposits in Japan and Kuroko-type VMS deposits in Sanjiang, respectively. In the latter case the hydrothermal solutions reacted with host rocks and mixed with cold seawater percolating downward, and circulated through volcanic rocks resulting in development of alteration zones and formation of ore minerals in Kuroko-type VMS deposits."

Jan 1, 1993

By C. H. Sleeman

"The Iron Ore Company of Canada constructed a beneficiation complex in Sept-Iles, Quebec, to concentrate and pelletize earthy red hematite iron ores from the Knob Lake area. The plants were scheduled for initial production during the first quarter of 1973.Many problems have been experienced to date. Difficulties in controlling the process, excessive mechanical failures, design deficiencies and manpower-staffing problems have caused an extended start-up. The problems are now essentially solved and, with the completion of some additional minor modifications, it is expected that the plants will be producing premium iron ore pellets at or near rated capacity within the next immediate period."

Jan 1, 1976

By R. G. K. Morrison

As mines grow deeper, the problem of ground control becomes one of increasing importance. The literature on the subject has grown extensively in the past few years, but is still far from conclusive. Detailed and precise observations are on record covering most phases of the problem, and control measures have progressed to the point where, in a large measure, they are effective. The success of methods to date must be attributed to the efforts which have been exerted to reduce convergence of stope walls and to the realization that a regular progression of stope faces approaching longwall has a beneficial effect. This paper attempts to explain the relationship between these two factors and the general problem of ground control. The problem at present lacks the co-ordination of the practical with the scientific outlook, but fortunately as time goes on there are indications that our scientific friends are becoming more interested and more familiar with the practical issues involved. Opinions vary widely regarding the mechanism of the problem and there are several schools of thought, two only of which will be discussed. One associates the incidence of rock-bursts with the stresses built up by a sagging hanging-wall, while the other takes the view that stresses primarily responsible for the sagging hanging-wall are also the cause of rock-bursts. The first group starts its reasoning from the convergence of the walls, probably the most conspicuous feature of deep mining, and works back to the conclusion that rock-bursts are in sorne way due to the breaking up of the sagging layers. The second group begins with the stress zone apparent around excavations at depth and follows mathematical conceptions based on certain assumptions which, in the absolute sense, are known to be inaccurate, but which are justified by the similarity between the conclusions reached and the results obtained in practice. This reasoning is followed to the point where rock-bursts result from the failure, under stress, of rock in situ, quite independent of wall convergence.

Jan 1, 1939

By M. Hashemzadeh

The efficiency of water use is a top priority for the global minerals industry, especially in regions with limited freshwater supplies. In these areas, the freshwater shortage has prompted mining companies to search for alternatives to freshwater sources. Seawater has been proven to be a potential water source for mineral beneficiation and metal extraction processes. This study compares chalcocite leaching behavior with ferric chloride to that with cupric chloride. We carried out leaching tests with a highly pure chalcocite sample in jacketed reactors under fully controlled pH and solution potential. The effect of chloride concentration, oxidant concentration, and temperature on copper extraction was quantified in both cupric and ferric chloride systems. In the ferric chloride system, increasing ferric concentration showed a positive effect on the first stage of chalcocite leaching. In the second stage, increasing temperature markedly enhanced copper extraction. In the cupric chloride system, chloride concentration presented a considerable effect on both the first and second stages of leaching, while temperature had a remarkable effect only on the second stage. The findings of this study would be beneficial to mine operations aiming to replace fresh water with seawater for heap leaching of chalcocite. INTRODUCTION Mineral processing operations/plants are normally operated adjacent to mines which are often located in remote and arid area, such as northern Chile, southern Peru and Australia with limited access to fresh water (Liu, Moran, & Vink, 2011, 2013). Water scarcity in these areas has prompted mining companies to invest in sustainable technologies to reduce the water use and/or increase the water use efficiency. One of the current sustainable approaches in mineral processing operations is to replace fresh water with seawater. Seawater is now being increasingly used for mineral beneficiation and metal extraction processes (Hernández et al., 2015). Another application of seawater could be for heap leaching of copper secondary sulfides, mainly chalcocite. However, the high concentration of chloride ion in seawater may significantly affect leaching kinetics of copper sulfide concentrates and ores (Watling et al., 2014). Therefore, it is essential to develop a fundamental understanding of the leaching of chalcocite in chloride media.

Jan 1, 2019

By M. S. King

"A simple method is proposed for determining the long-term deformation behaviour of evaporites. The theory developed can be tested by measuring the change in diameter as a function of time of a vertical mine shaft opposite evaporite strata. Ultimate shaft closures predicted by the theory agree well with those calculated with the very much more complex theory of Serata (1968), provided that sufficiently high octahedral shear strengths are used in the former.An analysis of measurements made in an isolated opening in a Saskatchewan potash mine shows that the octahedral shear strength of the surrounding potash and halite was approximately 500 psi several years after the opening was mined. This value is less than that deter-mined experimentally for halite by Serata. The same data indicate, furthermore, that the in-situ octahedral shear strength is decreasing slowly with time.The current controversy regarding the actual deformation of evaporites will only be resolved by the cooperation of potash producing companies in releasing data on the long-term deformation of their mine shafts."

Jan 1, 1971

By G. T. Lapidus, R. Zárate-Gutiérrez

Selective leaching of lead from a Pb-Ag-Zn concentrate with hydrogen peroxide in citrate solutions was studied at room temperature. Leaching tests were performed, varying the H2O2 concentration and the solid-liquid ratio, holding the solution pH constant at 7, and the citrate concentration at 1 M. Lead extractions of 100 % were achieved with 4 and 5 times the stoichiometric quantity needed to form elemental sulfur, with only a small amount of metal impurities dissolved (Ag, Zn and Fe). The lead solubility limit at those conditions was found to be ~21 g L-1. X-ray diffraction analyses of the leach residues were free of galena (PbS), while other metal sulfides, such as sphalerite (ZnS), chalcopyrite (CuFeS2) and pyrite (FeS2), were basically unaffected.

Jan 1, 2014

By D. H. Schwarz

The performance of proton exchange membrane (PEM) fuel cells depends on catalyst layer composition and structure. Experimental observations reveal that state-of-the-art catalyst layers consist of microporous agglomerates of carbon-supported catalyst sites bound together by polymer electrolyte. In between the agglomerates are macropores which provide pathways for the transport of gaseous reactants. In this work, three-dimensional, multicomponent and multiphase transport computations are performed using a computational fluid dynamics (CFD) code (FLUENTTM) with a new PEM fuel cell module, which has been further improved by taking into account the detailed composition and structure of the catalyst layers using a multiple thin-film agglomerate model. In this model, it is assumed that thin films of polymer electrolyte and liquid water surround the catalyst sites. The results of CFD computations show that transport limitations associated with the thin film of polymer electrolyte and the presence of liquid water in the catalyst and gas diffusion layers have substantial negative effects on PEM fuel cell performance. Also, the results of computations with variable distributions for a given precious metal loading show that, in general, uniform catalyst loading provides the best fuel cell performance.

Jan 1, 2005

By Neil Campbell

"The gently-dipping Devonian dolomite beds south of Great Slave lake in northern Canada are nearly every-where concealed by a cover of glacial drift and muskeg. Nevertheless, in 1898 or earlier, four small outcropping areas of dolomite, richly mineralized with lead and zinc sulphides, were discovered. Exploration work performed here up to the end of 1930, included intensive trenching and drilling of the showings, together with mapping and wide-spaced drilling in the surrounding region. This work proved that the discoveries are isolated pockets of mineralization much too small to be commercially valuable by themselves. No evidence of orebodies elsewhere was reported.Meanwhile, mapping by the G.S.C. in the Shield far to the east disclosed major Precambrian faults, some of which can be projected southwesterly (under a cover of Paleozoic sediments) to the vicinity of Pine Point. During the period from 1940 to 1947, consideration was given, by The Consolidated Mining and Smelting Company Ltd., to evidence of a theoretical possibility that, although apparently dormant in Paleozoic times, these faults may have provided a structural control and a source of ore-bearing solutions in some post-Devonian period. From this, it was postulated that the breaks might have created, in the overlying dolomite, a linear array of orebodies concealed by overburden but lying in a belt of considerable length and in a position predictable within practical limits. A program of drilling designed to test and exploit this specific concept was conducted from 1948 to 1955.he drilling within the new, theoretically-defined search area resulted in the discovery of many lead-zinc ore-bodies, none of which was exposed at the surface. Some of these are large and (as indicated by 1965 production records) very rich. They are situated 1 to several miles distant from, and apparently not connected to, the earlier-known surface discoveries. The drilling also disclosed that the ore, which consists of disseminated sphalerite and galena replacements together with colloform sphalerite and coarse galena cavity fillings, occurs mainly at certain stratigraphic horizons within a large, coarsely-recrystallized dolomite barrier reef. Considerable fracturing and folding was found. It has been suggested that reef development was influenced by post-Precambrian tectonic movements associated with the old faults in the basement complex. The ore may have been deposited by solutions moving from distant sources to favourable structural and chemical environments in or related to the reef.In more recent exploration performed in the course of preparing for mining production, the rate of ore discovery within the same general geological context has been greatly accelerated by the use of new geophysical techniques and drilling equipment. Reserves of 21.5 million tons, averaging 4 per cent lead and 7.2 per cent zinc, were reported in 1965, and production from open pits at the rate of approximately 248,000 tons of concentrates per year is in progress"

Jan 1, 1966

By M. Vaillé, B. Bossé, N. Durupt, A. Michaut

Imouraren is a sedimentary uranium deposit (> 150,000 tU @ 800 ppm), located approximately 100 km North-Northwest of Agadez (Niger); its depth reaches 110 to 170 meters. For low-grades ores, heap leaching is commonly considered as the appropriate technology for metal recovery. More precisely, the ore is crushed (≤ 300 mm) and agglomerated before being stacked. In this case, sulfuric acid can be added during agglomeration and/or irrigation (for three months to a year) to improve uranium recovery. It is known that mineralogical, chemical and physical properties of the uranium ore impact recovery, yet many challenges remain to increase recovery using this process. For example, ore heterogeneity and spatial variability (e.g., variation in uranium, carbonate and/or clay contents) can affect heap leaching performances (i.e., metal recovery, acid consumption or neutralization, percolation rate). However, laboratory column tests using composite ore sample that do not consider ore heterogeneity are widely used to anticipate recovery. Consequently, a new approach that consists in using Imouraren drill core ore samples was recently investigated. This latter also enabled a better assessment of the main parameters that influence uranium recovery and proposed a new predictive model to optimize mining operations.

Jan 1, 2020

By H. Thalenhorst

For an advanced mineral exploration project that has a ?nugget? issue making the assessment of the deposit grade difficult, a bulk sampling program using a sample tower can provide information that is otherwise not obtainable prior to actual production. This information includes the verification of predicted resource grades for the bulk sample tonnage (and, indirectly, of the methods and parameters used for the grade estimate), confirmation of the physical and grade continuity of the mineralization, and geotechnical data for a future mining operation. The information gathered will improve the input of a feasibility study, particularly with respect to expected mining grades, which are the key economic parameter for most mining projects. The bulk sample rejects can be used for pilotscale metallurgical testwork. Bulk sampling is also useful in cases of potentially biased drill-hole assay results and in the reliable determination of ore grade before shipment of ore from production or development operations to an external beneficiation plant. This paper presents a practical bulk sampling and sample preparation protocol, lists design features for the sample tower, examines the sampling errors that will be encountered, provides information on quality control procedures, and looks at the costs and benefits of such a program, based on the experience of undertaking bulk sampling programs during the period of 1985 to 2008.

May 1, 2010