Search Documents

By D. S. Campbell

THE chief factors influencing the decision to build the Big Missouri mill underground were the topography of the country and the climate. The location underground assured certain saving in the cost of operation, such as the hearing of the mill, shovelling snow, and handling ore, which, over a period of time, would offset the greater initial cost of the mill excavation and machinery installation underground, as compared with the cost of a like plant on the surface. At Gilman, Colorado, where conditions are somewhat similar, the Empire Zinc Company, at their Eagle mine, are treating their lead-zinc ore in a mill built entirely underground. Company officials made a study of this plant before proceeding with the mill at Big Missouri. LOCATION, CLIMATE, TOPOGRAPHY The Big Missouri mine is situated on the Upper Salmon river, 22 miles north of Stewart, B.C., which is at the head of Portland canal, a narrow natural channel which penetrates 100 miles inland from the coast into the Coast Range mountains. Stewart, the distributing centre for the district, is about 600 miles north of Vancouver. The Big Missouri claims lie on and down the sides of the Big Missouri ridge, which extends north and south between the Salmon River and Cascade Creek valleys. The ridge rises to an elevation of 3,600 feet, is about half a mile wide, and to the east slopes down to the Joker flats in Cascade Creek valley. The Big Missouri camp is located on the flats at elevation 2,800 (see Figure 1). Preliminary development of the property took place from this point with an adit driven under the ridge. The western side of the ridge slopes steeply down to the Salmon glacier at elevation 1,900. Ore found on the 2,850 level extended down, and, in order further to explore the ore-body, the 2,850 level was driven through to the west side of the ridge, a surface incline tramway was built, and a lower tunnel driven at elevation 2,350, five hundred feet below the original 2,850 level, from the west side of the ridge. This tunnel development avoided the necessity of sinking, which would have been costly, as the mine makes a great deal of water (see Figures 1 and 2).

Jan 1, 1938

By Neil Campbell

"The gently-dipping Devonian dolomite beds south of Great Slave lake in northern Canada are nearly every-where concealed by a cover of glacial drift and muskeg. Nevertheless, in 1898 or earlier, four small outcropping areas of dolomite, richly mineralized with lead and zinc sulphides, were discovered. Exploration work performed here up to the end of 1930, included intensive trenching and drilling of the showings, together with mapping and wide-spaced drilling in the surrounding region. This work proved that the discoveries are isolated pockets of mineralization much too small to be commercially valuable by themselves. No evidence of orebodies elsewhere was reported.Meanwhile, mapping by the G.S.C. in the Shield far to the east disclosed major Precambrian faults, some of which can be projected southwesterly (under a cover of Paleozoic sediments) to the vicinity of Pine Point. During the period from 1940 to 1947, consideration was given, by The Consolidated Mining and Smelting Company Ltd., to evidence of a theoretical possibility that, although apparently dormant in Paleozoic times, these faults may have provided a structural control and a source of ore-bearing solutions in some post-Devonian period. From this, it was postulated that the breaks might have created, in the overlying dolomite, a linear array of orebodies concealed by overburden but lying in a belt of considerable length and in a position predictable within practical limits. A program of drilling designed to test and exploit this specific concept was conducted from 1948 to 1955.he drilling within the new, theoretically-defined search area resulted in the discovery of many lead-zinc ore-bodies, none of which was exposed at the surface. Some of these are large and (as indicated by 1965 production records) very rich. They are situated 1 to several miles distant from, and apparently not connected to, the earlier-known surface discoveries. The drilling also disclosed that the ore, which consists of disseminated sphalerite and galena replacements together with colloform sphalerite and coarse galena cavity fillings, occurs mainly at certain stratigraphic horizons within a large, coarsely-recrystallized dolomite barrier reef. Considerable fracturing and folding was found. It has been suggested that reef development was influenced by post-Precambrian tectonic movements associated with the old faults in the basement complex. The ore may have been deposited by solutions moving from distant sources to favourable structural and chemical environments in or related to the reef.In more recent exploration performed in the course of preparing for mining production, the rate of ore discovery within the same general geological context has been greatly accelerated by the use of new geophysical techniques and drilling equipment. Reserves of 21.5 million tons, averaging 4 per cent lead and 7.2 per cent zinc, were reported in 1965, and production from open pits at the rate of approximately 248,000 tons of concentrates per year is in progress"

Jan 1, 1966

By Victor F. Hollister

Elemental sulphur occurs as aformational sedimentary deposit in Upper Devonian Wabamun evaporites near Coronation, Alberta. The deposit developed in a stratigraphic jacies-change lrap; it is assumed that petroleum reacted with anhydrite to form sulphur, calcite, hydrogen sulphide and other reaction products. The deposit contains about 362,800 tonnes of sulphur and lies at a depth of 1200 m. The Coronation deposit is expected to be geologically typical of such other native sulphur deposits as may be found in Wabamun Group sediments. Widespread sour gas sulphur production f rom the Wabamun suggests the possibility that additional native sulphur deposits will ·be found.

Jan 1, 1984

By DON E. MacDONALD

Marl in Alberta is confined to highly specific geological, hydrogeologica/ and climatic settings. Tufa is fa irly abundant in those areas of western Alberta where bedrock is of the Paskapoo Formation. Marl and tufa originate when the following conditions are met: presence of a carbonate source in drift or nearsurface bedrock; leaching of the carbonate by percolating groundwater; transportation of calcium and bicarbonate ions in a permeable aquifer; discharge at the surface as springs, seeps or lakes; re-precipitation of calcium carbonate. Alberta has seven categories of marl and tufa deposits, based upon over-all depositional environment and calcium carbonate

Jan 1, 1984

By M. Vaillé, B. Bossé, N. Durupt, A. Michaut

Imouraren is a sedimentary uranium deposit (> 150,000 tU @ 800 ppm), located approximately 100 km North-Northwest of Agadez (Niger); its depth reaches 110 to 170 meters. For low-grades ores, heap leaching is commonly considered as the appropriate technology for metal recovery. More precisely, the ore is crushed (≤ 300 mm) and agglomerated before being stacked. In this case, sulfuric acid can be added during agglomeration and/or irrigation (for three months to a year) to improve uranium recovery. It is known that mineralogical, chemical and physical properties of the uranium ore impact recovery, yet many challenges remain to increase recovery using this process. For example, ore heterogeneity and spatial variability (e.g., variation in uranium, carbonate and/or clay contents) can affect heap leaching performances (i.e., metal recovery, acid consumption or neutralization, percolation rate). However, laboratory column tests using composite ore sample that do not consider ore heterogeneity are widely used to anticipate recovery. Consequently, a new approach that consists in using Imouraren drill core ore samples was recently investigated. This latter also enabled a better assessment of the main parameters that influence uranium recovery and proposed a new predictive model to optimize mining operations.

Jan 1, 2020

By D. H. Schwarz

The performance of proton exchange membrane (PEM) fuel cells depends on catalyst layer composition and structure. Experimental observations reveal that state-of-the-art catalyst layers consist of microporous agglomerates of carbon-supported catalyst sites bound together by polymer electrolyte. In between the agglomerates are macropores which provide pathways for the transport of gaseous reactants. In this work, three-dimensional, multicomponent and multiphase transport computations are performed using a computational fluid dynamics (CFD) code (FLUENTTM) with a new PEM fuel cell module, which has been further improved by taking into account the detailed composition and structure of the catalyst layers using a multiple thin-film agglomerate model. In this model, it is assumed that thin films of polymer electrolyte and liquid water surround the catalyst sites. The results of CFD computations show that transport limitations associated with the thin film of polymer electrolyte and the presence of liquid water in the catalyst and gas diffusion layers have substantial negative effects on PEM fuel cell performance. Also, the results of computations with variable distributions for a given precious metal loading show that, in general, uniform catalyst loading provides the best fuel cell performance.

Jan 1, 2005

By Guy Demers

"This paper defines the responsibilities and functions of the Maintenance Department, and its organization, physical and human assets, highlighting the unique operating problems. Due to the self-sufficient aspect of the Asbestos Hill Deception Bay project, the Maintenance Department cover-s fields that are numerous and very dissimilar: production, mobile, processing, service, power generation, fire protection, heating, water and sewage disposal equipment. Added to this, buildings, plant and camps, wharves and communications equipment all demand versatility, adaptability and expertise from maintenance personnel. Good maintenance practices are a necessity in this environment and are more critical than at southern locations; that is, high-quality replacement material, complete and well-controlled preventive maintenance, major repairs on a component-replacement basis, updated inventory, efficient training and permanent contacts with suppliers, combined with an equipment improvement program, updated specifications on lubricants, hoses, seals, filters, etc., are mandatory. The seasonal aspect of the operations applies a great deal of pressure on the maintenance team, as the production months do not permit major repairs. Short- and medium range planning and accurate evaluation of equipment conditions highly influence production efficiency. Maintenance control, planning and scheduling do not follow the accepted standard routines, as personnel turnover normally does not permit an accumulation of knowledge of the equipment history and condition by the •individual tradesman."

Jan 1, 1976

By D. Prince, G. Nollet

"Since 1994, Aur Ressources has operated Louvicourt mine, a zinc and copper mine close to Val d’Or, at a rate of 4300 t/d. Ever since the start-up of the plant, management has encouraged innovative approaches in reliability.The first of three papers will discuss the vibration monitoring program in place. The program will be described and two examples will be given: detection of a rolling bearing defect on a pinion driving the ball mill and identification of wear on the bearings of the flotation cells. Figures on the return on investment and the costs of a monitoring program will also be given.The second article will discuss the lubrication aspect. Since the establishment of a good monitoring and oil analyses, Louvicourt mine decreased its oil consumption by more than 38 000 L/yr. In addition, the company set up an oil regeneration system that restores the original properties of oil.The third article will cover the management aspect. Work organization as well as the management philosophy enabling the employees to push predictive technology to higher levels will be examined in detail. The key elements which made it possible for Louvicourt mine to position itself among world-class companies in the organization of maintenance will be discussed. IntroductionThis article is the second of three on predictive maintenance at the Louvicourt mine operated by Aur Resources Inc. The first article, published in the October 2002 issue, was about vibration analysis for rotating machines. This article describes how lubrication and oil analysis for stationary machines permitted Louvicourt to save more than $150,000 within two years and presents the evolution of the oil analysis program.Louvicourt mine, located near Val-d’Or, Quebec, is a copper and zinc mining and milling operation that processes 4300 t/d of ore and employs 289 people. Production began in 1994. Louvicourt mine is a partnership between Aur Ressources (30%), Teck Corp. (25%), and Novicourt (45%)."

Jan 1, 2003

By C Carbonneau

In order to successfully produce columbium pyrochlore concentrates, St. Lawrence Columbium and Metals Corporation had to face two principal problems met in several new operations but possibly made more acute than usual owing to the newness of the project. 1.-The ore is particularly complex, as it is made up of an elaborate intermingling of carbonates and discontinuous ultra-alkaline rock bodies of various ages and types in which no less than seventy mineral have been re-ported. Obvious petrographic or structural controls are lacking. Ore boundaries have to be defined on the basis of assay results and the determination of several minerals which occur in trace amounts. 2.-The pyrochlore concentrates produced had to com-ply with a set of stringent specifications. This fact, combined with the low Cb205 content of the ore, necessitated the use of a beneficiation process that would have to operate at a concentration ratio greater than 100:1. A brief description of the mill circuit is given. Mill stability was obtained through extensive mineralogical study of the mill feed coupled with close geological and engineering control of the mining operations.

Jan 1, 1965

By M. Bustin, A. Hosseinian, G. Preisig

Hydraulic fracturing and hydraulic shearing techniques are essential for the development of unconventional oil & gas and geothermal resources. Such techniques will also play a key role in the development of CO2 sequestration, and management of high stresses encountered with deep mining. However, the optimal design of hydraulic injections is often limited by continuum treatments of the rock mass without consideration of the influence of the natural fractures present. These may interact with the hydraulic fracture to promote offsets or arrest, or may cause the natural fractures to undergo shear and dilation. Given the limited access to the rock afforded by deep boreholes common to oil & gas and geothermal projects, advanced numerical modeling is critical for understanding key mechanisms and interactions. In this work, we first present a coupled hydromechanical distinct-element model focusing on the propagation of a hydraulic fracture. Normal and shear displacements arising from the generated hydraulic fractures are subsequently integrated into a fracture flow model for detailed analysis of specific flow behaviour and fracture permeability. For this, a scanned 3-D profile of a natural fracture is used to correlate surface roughness to dilation as a function of shearing. Fracture flow is computed at different time steps corresponding to different fracture propagation states and geometries. Modeling results indicate that the opening of a tensile hydraulic fracture is accompanied by millimetre-scale shear displacements associated with slip and wedging between adjacent blocks. This may leads to a mismatch between the upper and lower walls of the fracture if asperities are irregular and strong enough. However, fluid-induced tensile fractures have low Joint Roughness Coefficients (JRC), and associated millimetre-scale shear displacements are too small to ensure a significant offset of asperities that prevent a fully-elastic closure when the hydraulic fracture is depressurized. Injection of proppant is thus critical to keeping hydraulic fracture apertures open. Future work is planned that will see the models calibrated against field data including microseismic event locations, magnitudes and source mechanisms, tiltmeter deformations, stress change, and pore pressures.

Jan 1, 2015

By J. A. Brusset

Introduction I am indebted for most of the information in this paper to Mr. P. S. Lea, Deputy Chief Inspector of Mines of Great Britain, and Mr. A. E. Crook, Engineering Inspector of Mines, Ministry of Fuel and Power. Other coal-mining men in Canada may be as surprised as I was to learn that there are twenty-five Diesel locomotives in service underground in British gassy coal mines. Many more are in use underground in non-gassy coal mines and in metal mines. Approval has been granted for an additional fifty flame-proof locomotives to be used in gassy mines, and these should be in operation by the end of 1946, or as soon as manufacturing facilities permit.

Jan 1, 1946

By P. E. Auger, J. E. Gill

"The zinc deposits to be described are in Lemieux township a few miles south of the Tabletop mountains, in the central part of Gaspe peninsula, Quebec. Although they have not been worked, they constitute a potential source of zinc and lead and structurally are of considerable interest.GENERAL CHARACTER OF THE OCCURRENCEThe deposits are in sharp-walled quartz-carbonate veins and breccia zones carrying locally, and in varying amounts, sphalerite, galena, pyrite, marcasite, chalcopyrite, and specularite. Those so far investigated strike generally north-south, have steep dips, and cut through sediments of Lower Devonian age, mostly calcareous argillites or siltstones. Wall-rock alteration is negligible.BROADER STRUCTURAL FEATURESThe principal known occurrences are in the south-central part of a dome structure measuring 6 by 5 miles. The argillaceous sediments are overlain, on the flanks of the dome, by sandstones and lavas. These have been stripped from the central part of the dome, revealing the veins in the argillites beneath. The veins formed after the volcanics, but the fractures and breccia zones in which the deposits formed are confined mainly to the argillite series, presumably because of the greater strength of the lavas.The argillite series is cut by dykes, sills, and small stocks of diorite and acidic 'porphyries' that are older than the veins.THE FEDERAL HILL AREAThe distribution of known veins is shown in Fig. 1. The characteristic features of the veins are well illustrated by the Federal Hill area shown in Figs. 2, 3, and 4, and described below."

Jan 1, 1954

By L. Tafaghodi, S. Sarbishei

"Following the depletion of nickel sulfide ores, laterites are considered as one of the main sources for producing nickel and cobalt. One of the primary steps in pyrometallurgical extraction of nickel from laterites involves partial reduction of the ore at temperatures below 1000°C. Studying the kinetics of laterite reduction provides valuable information on reducibility of nickel laterites using coal as a reductant. The present study investigates the reduction behavior of a nickel laterite by thermal gravimetric analysis and differential scanning calorimetry. Non-isothermal reduction tests and X-ray diffraction analysis were performed to find the main reactions that occur during the process. The kinetic parameters were calculated by Coats-Redfern method. The general model of simple reaction f(a)=(1-a)n was used for calculating kinetic parameters.INTRODUCTION Nickel (Ni) naturally occurs in the form of sulfide and laterite ores. Laterite ores are mainly available in tropical regions. Weathering phenomena during millions of years has led to the formation of several layers with specific mineralogy (Butt & Cluzel, 2013). The three main layers downward are limonite, smectite, and saprolite (Crundwell et al., 2011). Although laterites are the most available nickel ore resource (70%), their share in the overall Ni production is limited to 40% (Crundwell et al., 2011). The main reasons for not materializing the full potential of laterites are as follows (Ray et al., 1985): •,Laterite ores contain high water content (free and combined) which in turn results in high energy consumption of the extraction process. •,As Ni is present in the form of solid solution in laterites, physical upgrading methods such as flotation are not effective in increasing the Ni content before the extraction process. •,Extracting Ni from sulfide ores involve exothermic reactions which are beneficial due to decreasing the overall energy requirement of the process, however there is not efficient release of energy in the process of extracting Ni from laterite ores."

Jan 1, 2017

By J. P. Harrison, R. Roostaei

"In this paper we investigate the consequences of using conventional triaxial peak strength criteria in the polyaxial stress conditions that occur around the end of a long circular underground opening. A series of 3d boundary element analyses were performed using Examine3D to determine the stresses induced around the tunnel in different in-situ stress conditions. To discuss the applicability of a triaxial strength criterion in failure prediction, strength factors were computed for both the Ottosen polyaxial strength criterion and the triaxial Hoek-Brown criterion. Assuming that the Ottosen criterion is an accurate indicator of strength factor, the discrepancy from this value due to the Hoek-Brown criterion is the error in prediction.In order to simultaneously show the error in prediction and actual strength factor, a quantitative bivariate colour scheme is used to visualize the results. This allows rapid identification of regions with large error, and where either unsafe or overly conservative conditions occur. We show how the inappropriate use of triaxial criteria rather than polyaxial criteria leads to an under- or over-estimation of strength factor, and can result in uneconomic or unsafe design. Extending the analysis to different in situ stress regimes shows how the in situ stress conditions affect the assessment."

Jan 1, 2015

By D. McFadgen

"THE Dominion Steel & Coal Corporation, through its subsidiaries, the Old Sydney Collieries and the Dominion Coal Company Limited, produces 4% million tons of coal annually from eight submarine collieries situated on the eastern coast of Cape Breton Island. The present workings have a frontage of 20 miles and extend 31/2 miles under the Atlantic ocean on gradients varying from 4 deg. to 24 deg. To date, some of the workings have reached .a depth of cover up to 2,800 feet.The pitching seams, the annual seaward advance, the resulting depth of cover and the rdatively soft roof and floor have necessitated the adoption of extensive longwall mining, with room-and-pillar mining con-fined to areas above the 1,000 foot cover line, where 60 per cent of the -coal is left standing in pillars to support the ocean floor. Longwall mining accounts for 87 per cent of the total production with the remaining outputs obtained from room-and-pillar work and the narrow work development. Seventy-four per cent of the longwall production and 41 per -cent of the room and development production is completely mechanized.Although 2 tons of water is pumped from the collieries for each ton of coal mined, the working sections are relatively dry as the heavy make of water is essentially surface drain-age from the land crop areas. The dry workings and the long haulage distances, which in many cases exceed 4 miles, have resulted in a continuing programme to combat the dust hazard, both at the working face and along the mine roadways."

Jan 1, 1960

By C. Boudreault, M. Fortier, S. Fafard

In the forging industry, the increasing trend is to use DC cast billets as forging stock to replace extruded stock. However, there is little technical information available in open literature. In order to gain a better understanding of the behaviour of cast stock during deformation, a study was initiated to evaluate the impact of an homogenisation treatment on the billet prior to cold forging. Axisymmetric upsettings of cylindrical samples machined from DC billets were achieved in order to evaluate and compare flow stresses, crack initiation and propagation. Results show a 30% decrease in flow stress after homogenisation. Observations of the deformed samples show major cracking for the as-cast material. Optical microscopy and SEM observations have related the crack initiation to decohesion around ß -AlFeSi particles and subsequent growth along the constituent path. Homogenisation effectively breaks up and transforms the ß phase, present as platelets in the cast product, into smaller spherodised a-AlFeSi particles. This has the effect of preventing crack growth in the forged product. The homogenisation treatment also resulted in the reduction of Mg and Si in solid solution. The softer matrix generated 29% less die wear when compared to the as-cast structure. Based on the results of this study, it is thus recommended to homogenise cast billets prior to cold forging.

Jan 1, 2006

By L. A. Wrigglesworth, A. S. Dadson

The orebodies of the Giant Yellow-knife mine occur in zones of schist, in an assemblage of typical Precambrian greenstones which form part of the Yellowknife Greenstone Belt. One of the most interesting problems at the mine concerns the fold-like attitudes assumed by the schist zones. The internal structure of the zones and orebodies provides much evidence of folding. A logical conclusion would be that the zones represent a single horizon which has been folded and drag-folded in the ordinary course of mountain building. However, surface mapping, and correlation of certain marker horizons, in underground work, indicate a homo-clinal succession of steeply dipping flows. If this concept of the geology is correct, the zones must cross-cut the regional strike at a small angle and, in the over-all aspect, the regional dip at a large angle. A mechanical interpretation of the zone structure is presented as a suggestion for the present until new evidence is found.

Jan 1, 1959

By R. T. Elworthy

Canada ranks second in the list of world consumers of natural gas. In 1923 our production was nearly fifteen million thousand cubic feet valued at $5,800,000. Our output, however, appears very small compared with that of the United States, which in 1923 totalled over one thousand and eight million cubic feet, valued at $240,000,000. Natural gas is found in commercial quantities in three? provinces in Canada. New Brunswick: Natural gas in New Brunswick has been utilized commercially only since 1912,although the investigation of oil and gas possibilities of the province commenced as early as 1859. The annual production is a little more than one-twentieth of the total Canadian production and remains fairly constant from year to year. Ontario: In Ontario the earliest gas wells were drilled in Essex and Welland counties between the years 1885 and 1890. On account of the small demand in Canada the cities of Detroit and Buffalo were supplied with large quantities of gas from these wells, but this export was curtailed in 1898 and finally ceased in 1900. The production of natural gas in Ontario, mainly from fields in Lambton, Kent, Essex, Norfolk, Haldimand and Welland counties, increased rapidly from 1900 until the peak was reached in 1917, when over nineteen million thousand cubic feet valued at $3,641,587 was consumed.

Jan 1, 1925

By L. Newman, R. Wyrick, R. Berezowsky

The Stillwater Mining Company operates an integrated mines, mill, smelter and base metals refinery complex in Montana, USA for the production of a high-grade platinum group metals (PGM) bearing concentrate, nickel sulphate crystal and cathode copper from the PGM-containing nickel-copper converter matte. The complex was constructed in stages over several years, starting with the mine and the mill, followed by the smelter and finally, a base metals refinery, which was commissioned in 1996. Due to the relatively small quantity of matte production, a straightforward refinery process was initially selected to extract the base metals, which reported to a mixed nickel-copper solution for further treatment off-site, and yielded a high-grade PGM concentrate suitable for treatment in a PGM refinery elsewhere. Subsequently, as a result of increased matte production, the process was modified to separate the nickel and copper, and to produce a nickel sulphate salt and cathode copper. This paper describes the design and operation of the original and the modified processes utilized in the base metals refinery (BMR).

Jan 1, 2004

By G. W. Harris, P. Mousset-Jones, J. Daemen

"To minimize ore dilution induced by blast movement in surface mines, it is necessary to quantify such movement. This will enable more accurate location of the grade boundaries beneath the surface of a blasted rock pile before excavation. A method has been developed and tested to accurately measure the direction and magnitude of subsurface blast movement. This technique uses a cesium vapour gradiometer and a real-time, differentially corrected GPS system to locate pre- and post-blast position of magnetically enhanced target objects placed within blastholes inside a bench. The procedure developed does not require the blasted rock to be disturbed, and the movement information is available within a sufficient time to allow for modification of the selective mining boundaries for each surveyed blast. It was found that the maximum depth of target detection was 18 m, with the overall accuracy being measured as ±1 m (horizontally) and ± 1.2 m (vertically). IntroductionOre dilution is a critical concern for many mining operations. In some instances, it may be the cause of considerable mineral loss. Where the mineralization is finely grained, sedimentary and disseminated in nature, and exhibits no clearly defined visual ore/waste boundary, there is a heightened possibility for ore grade dilution. In most modern open pit gold mines, it is economically desirable to minimize dilution in the production process through the practice of selective mining by defining pre-blast ore digging boundaries, called digging polygons, on the preblast bench area. The polygons’ positions are defined by sampling the production drill holes, with the resultant assay and survey data being used to estimate the areas of specified grade content within the bench. Once the ore is blasted in the bench, the pre-blast locations of these digging polygons are flagged as designated areas on the broken ore pile. The purpose is for the loader operator to be able to recognize which areas of blasted rock are to be sent to the appropriate processing facility or to the waste dump."

Jan 1, 2001