Search Documents

By R. O. Burt, D. J. Ottley

"SYNOPSISRecent developments in the use of the Bartles-Mozley table and the Bartles CTS screen are described for the gravity preconcentration of fine heavy mineral and metal particles present in low grade pulps. The B-M table is a relatively new device used for the recovery of particles of up to 100 micron size down to 5 microns or in the case of gold and platinum, down to 1 micron. The CTS screen is a wet screening device used for feed preparation ahead of the Bartles-Mozley table and will size effectively down to about 300 mesh. Results and operating data for a number of different materials are given including outline flowsheets; the effects of the major variables on the performance of the table are briefly discussed. The potential of the B-M table to treat a variety of different ores, coal, tailings, and waste products are considered. The utilization of the B-M table in association with other unit processes to improve overall results as well as to improve the economics of design and performance of plants are also mentioned.INTRODUCTIONA number of new gravity concentration devices have been developed in recent years for the recovery of fine heavy mineral and metal particles but for reasons which include low capacity, high capital or operating costs, competition from other and better processes, the absence of simplicity or reliability in operation etc., only a few which include the Bartles-Mozley table, have been proved to be of commercial application.The name of the machine is derived from the inventors name, Richard Mozley, who developed the B-M table at the University of Bristol in England. The table was subsequently taken up and patented, world-wide, by the National Research Development Corporation a British government agency. An exclusive license to manufacture the table was granted by NRDC to Bartles (Carn Brea) Ltd. in Cornwall, England."

Jan 1, 1973

By R. S. Boorman, H. G. Ansell

"Poor separation of lead from a copper concentrate of a major base metal producer was thought to have resulted from copper (0.2-0.4%) in the galena which caused it to float with chalcopyrite. No inclusions of copper mineral were detected which could account for the flotation of galena. The tendency for copper-bearing galena to float with chalcopyrite was confirmed by Hallimond-tube experiments in which the floatability of copper-doped synthetic galena (0.1-0.4% Cu) was approximately four times as high as copper-free galena. The difference in the cell edge (5.9338 ± 0.0003 A, Cudoped galena; 5.9361 ± 0.0002 A, Cu-free galena) indicated that the copper was lattice-bound and did not occur as submicroscopic mineral inclusions."

Jan 1, 1973

By Nicholas J. Welham

"The effect of extended ball milling has been studied for two industrial processes: (1) the processing of metal sulphide concentrates; and (2) the carbothermic reduction of ilmenite to synthetic rutile. The plant concentrates were a gold ore with 128 g/t Au of which 8% was non-refractory and a zinc concentrate with copper impurities.The gold concentrate showed complete dissolution of the gold bearing minerals after milling giving almost complete gold liberation. The zinc concentrate showed almost all of the sulphides had solubilized leaving the gangue and elemental sulphur. A study of pure pyrite and arsenopyrite shows that selective dissolution should be possible by a simple leaching process directly after milling.The milling of ilmenite and coal together results in a temperature decrease of 150°C in the subsequent carbothermic reduction of ilmenite, in addition to improving both the rate of reaction and the selectivity of reduction to rutile. IntroductionAlmost all mineral processing plants use mills for the size reduction of particles prior to physical and chemical processing. When continuing beyond size reduction the energy transferred causes deformation, breakage and realloying of particles giving a steady-state particle size. The breaking also causes increasing damage to the crystal structure by formation of smaller grains giving an increasing number of grain boundaries and increasing crystalline defects due to deformation. The increasing number of grain boundaries and defects leads to increased reactivity, which can be seen directly by a reaction within the mill, or indirectly, via a decrease in the subsequent annealing temperature required for reaction."

Jan 1, 1997

By S. Parent, J. -F. Lepage, S. Glover

"Goldcorp – Eleonore’s 7 000 tonnes per day gold mill was started up in October 2014 and achieved commercial production in April 2015. During the first year, operation has faced challenges from grinding, flotation, sulfide cyanidation and tailing filtration to achieve targeted throughput, availability and recovery.The optimization of non-sulfide tails filter cloth lifetime and filter press availability had the most significant impact on ramp-up of both mill throughput and availability. A change in steel ball addition size to the grinding circuit was made to meet the targeted p80 of 65 µm. Various optimization efforts were conducted on the flotation circuit, intended to recover all sulfide-bearing minerals. The goal is to attain the environmental target of 0.12% sulfur in flotation tails (to eliminate acid mine drainage or AMD), while an average of 0.31% sulfur was obtained over the first months of 2015. Collectors, frothers, activators and hydrodynamic parameters were tested to improve the circuit desulfurization efficiency. High sulfide reactivity in pre-oxidation and cyanidation severely impacted dissolved oxygen levels and cyanide consumption. Studies were undertaken to understand the effects of mineralogy, grind size and leach conditions on gold dissolution kinetics and cyanide consumption. Efforts were focused on pre-oxidation to restore dissolved oxygen levels as well as optimizing both lead nitrate addition and pre-oxidation time.INTRODUCTIONGoldcorp Eleonore’s mill commissioning started in September 2014. It was considered to operate the mill at 3 500 tpd during design, as the mine was planning to operate at this throughput for the first year. However, with the stockpile of ore and a higher throughput from the mine, the mill was able to run at higher tonnage than initially anticipated.While increasing tonnage, a few bottlenecks were discovered and overcome in areas such as filtration and cyanide destruction. There were also recovery issues which were addressed in areas such as grind and sulfide leach. This paper focusses on the first complete year of operation ending September 30th 2015. A process description and the flowsheet are presented below and it will then go into detail about operational, metallurgical, mechanical and design issues experienced during the year."

Jan 1, 2016

By C. Edwards

ABSTRACT: Milling operations in northern Saskatchewan’s Athabasca Basin have produced uranium continuously since 1975. During that period, the Athabasca Basin has been one of the world’s premier uranium camps, yielding more than 660 million lb (299,370,964 kg) of U3O8. In this paper, the author describes former and current milling operations and discusses why and how the milling process has changed and developed over the past 35 years. The author’s considerations for the future of uranium extraction in the Athabasca Basin conclude the paper.

Jan 1, 2012

By Roger Lafrance

"This paper discusses various aspects affected by the use of large-diameter boreholes in underground mines. Topics covered consist of noxious fumes, vibrations, post-blast effects, various types of explosives, the cordine system in production blasts, the slider primer system and wall-control methods. In general, the paper is an overview of this important fact of underground mining.IntroductionWith economical factors leading the way, many reasons motivated drilling equipment companies to develop equipment that can drill holes up to eight inches in diameter and even larger for underground applications. One of these other reasons is the fact that many orebodies were considered marginal, given the high costs of conventional mining methods utilizing small diameter boreholes. With these criteria in mind, accelerated programs were put in motion to develop equipment that would reduce both-development and production costs in underground mines. Change s in any basic program often affect other areas down the line. This is particularly true with the ad vent of large-diameter boreholes underground.C-I-L Inc. is certainly no stranger to this phenomena. Whether production headings increase in size and tonnage or whether production increases due to lower costs, one fact remains unchanged and that is the fact that all development and production holes are loaded and blasted whether they be of small or large diameter. Due to this fact, C-I-L Inc., as a leading explosives manufacturer, initiated a program to examine blasting methods in use in surface work with the intent of revising these method s for underground applications. Research facilities were also oriented toward developing appropriate products. This was a task that was accepted with anticipation, with the result that many new blasting systems and methods were brought forward, thanks to the collective efforts of both the consumers and manufacturers."

Jan 1, 1984

By P. Hr?enjak

Two groups of methods are usually used in design procedures of underground excavation of dimension stone: the analytical and numerical methods of analysis. In all of these methods the in situ rock mass strength represents the main problem. This is due to massive rocks in dimension stone deposits, consisting of large blocks of rock separated with particular discontinuities, for which the Hoek-Brown empirical criterion, developed for jointed rock masses, cannot be realistically used to estimate rock mass strength, especially for a particular block of rock mass or a particular pillar. On the basis of the regular underground excavation process of dimension stone by separating blocks with the flat jack application, we developed the in situ flexural strength testing method. We carried out numerical analyses and evaluation of uncertainty of measurement in order to validate the in situ flexural strength testing method. On the basis of very good validation results, as well as results of the in situ flexural strength testing of exploitable layers on the ?Kanfanar? quarry, we introduced a new coefficient of reduction, which can be used for correction of other strength parameters determined by laboratory testing for obtaining a realistic value of rock mass strength.

Aug 1, 2013

By Patrick M. Y. Waye

As mines utilise more automation in mining operations to improve efficiency and safety, a corresponding increasing demand is placed on the transport of information. Some of the recent technological advances in underground telecommunications are described for various data, voice and video applications. In particular, two new innovative underground communication systems are described, one with high speed data at 30 Mbps and the other for mine wide evacuation and safety applications. The high speed data system incorporates stateof- the-art data networking technologies and the existing leaky cable narrow band radio channels. The new system provides over the same basic infrastructure the high speed data network at 30 Mbps TCP/IP Ethernet with 100 Base-T interconnection, plus 32 narrow band radio channels. The second system is a system for mine wide evacuation with "through the earth" communication infrastructure. Emergency situation can be communicated to and from all the miners within seconds through a central control location. The technology involved does not require leaky cable or any other similar transmission media installation. Many applications are possible, including warning miners of emergency situations, mine rescue operation to communicate with trapped miners, regular reporting from miners working alone.

May 1, 2001

By Hans Lundberg

The magnetometer which was developed during the war for detecting submarines has proven exceedingly valuable in outlining deep-seated structures in oil exploration, and will be useful also to geologists in outlining regional structural features in the Precambrian. Our magnetometer has been developed to outline local and detail structures. 1 am quite sure that all geophysicists and geologists would agree with me that, in ore prospecting, it is important to obtain as much detailed information as possible. We know that, as we ascend from the ground and get away from the magnetic ore-bearing structures and orebodies, the magnetic intensity decreases rapidly, but, worse than that, we lose the details even faster. Figure l shows two strong, very sharp, magnetic 'highs' over two orebodies which, as our distance increases, rapidly merge into one fairly broad, moderately strong anomaly. If we drilled on this maximum, we would not encounter any of the orebodies. Therefore, we should fly the airborne magnetometer as close to the ground as possible in order to duplicate the results of the magnetic ground surveys. The first chance to accomplish this came with the helicopter, which is an exceedingly maneuverable aircraft. It can be landed in a cleared space not much more than fifty feet square. With floats, it can be landed anywhere, even in a swamp, on thin ice, or on soft snow. It can stand still in the air, hovering over a given point. It can ascend and descend vertically, fly sideways and even backwards, at the will of the pilot. It flies forward at any speed up to l00 miles an hour. The helicopter can be taken to any desired position at a given time. It can fly at any useful altitude from a few feet to several thousand feet above the ground. It can fly very close to the ground with safety. In bare areas, the survey flight may be performed a few feet above the ground. In forested areas, however, the flights, to clear the trees, must be made at l00 to 150 feet. To mark out a certain point, a small parachute-like marker may be draped over a tree or laid on the ground. This can be done from the helicopter without touching the ground.

Jan 1, 1947

By K. Schrijver, G. Beaudoin

"Four occurrences of galena-cemented sandstones, exposed in the Lower St. Lawrence - Gaspésie area, are described. They constitute a new, insufficiently explored type of deposit in Quebec.One mineralized body, a minor occurrence, is hosted in Lower Devonian rocks deposited in an estuarine, intertidal river channel during a marine regression; major cements are dolomite and sulphides. Another occurrence, a drilled prospect, is hosted in Upper Silurian rocks deposited unconformably on Cambro Ordovician basement during a marine transgression. With galena and quartz as main cementing minerals, it is similar to some well-known, economic sandstone-lead deposits. A third and fourth, a drilled prospect and a minor occurrence, are hosted in Upper Cambrian rocks deposited on continental slopes. In both, sulphides mainly occupy a secondary porosity. The differences between the third and fourth occurrences are: (1) cementing translucent minerals (carbonates and barite in one; chlorite in the other); (2) chronology of final subsurface dissolution (prior and subsequent to sulphide precipitation, respectively); and (3) important fracture porosity only in the barite-bearing deposit.The diversity of the four occurrences, and the unequal geological knowledge of their respective features, prohibit the formulation of uniform guidelines for further exploration.IntroductionThe attention of the mineral exploration community is drawn to four occurrences of galena-cemented sandstones (Fig. 2A) in the Cambrian of the Taconian Orogen and in the Siluro-Devonian basin of the Lower St. Lawrence and Gaspésie area (Fig. 1). In view of the fact that sandstone-lead deposits (Bjerlykke and Sangster, 1981) are, or have been, mined in several countries (e.g . Laisvall in Sweden: see Rickard et al., 1979; Largentiere in France: see Foglierini et al., 1980), the mere presence of occurrences in Quebec indicates that the mineral potential of some parts of the Appalachians requires further evaluation.Exploration for the deposits considered here is essentially restricted to geological methods and drilJing (e.g . Mainguet Suares and Samama, 1969), since the response to geophysical methods is virtually nil, at least in the initial, surficial stage of an exploration program. As the particular disciplines of geology utilized in exploration depend a great deal on the geological setting of a mineral occurrence, the diversity of the Quebec deposits is of prime importance. Therefore, the four occurrences (Fig. I, Table 1) studied by the authors are herein briefly described with emphasis on their stratigraphic and tectonic setting, and on the evolution of pore space and sequential occlusion of pores and fractures. Prior to further research in and around the occurrences, now in progress (e.g. Beaudoin, 1987; Beaudoin et al., 1987), it is hoped that the following outline will be useful to the explorationist."

Jan 1, 1987

By T. V. Lord

Minerals containing uranium have been successfully pre-concentrated by flotation at Queen's University, Kingston. In particular, uraninite, uranothorite, euxenite, and fergusonite, have responded to flotation to yield grades of 0.2 to 6.0 .per cent U .o. with recoveries of 85 to 98 per cent, from heads analysing approximately 0.10 per cent U3Os. Of the ten or so radioactive samples examined to date, two distinct groups were recognizable, firstly, those samples in which uranium was the sole constituent of economic interest, and, secondly, those in which Columbium (with minor amount of tantalum) was present in addition to uranium. For the purpose of this paper, the results of investigation on two samples of each of the above groups have been selected as typical.

Jan 1, 1945

By M. I. Abbas, M. A. Shahin, M. S. Ahmed

"The influence of annealing of galvanized steel (galvannealing) on its corrosion kinetics in a saturated solution of Ca (OH)2 has been studied by means of the polarization resistance method.Galvannealing heat treatment was carried out at 450°C and 550°C for varying times. Annealing at 450°C for 24 hr or at 550°C for 5 hr showed the highest corrosion potential (Ecorr) ~= - 400 m V/ SCE as well as, the lowest corrosion current density (icorr ~= 3 mA.cm-2, while Ecorr and icorr of the unheated specimens were ~= - 1400m V/SCE and == 20 mA.cm-2, respectively.Polarization curves were also obtained for the as-received galvanized specimens together with the galvannealed ones.INTRODUCTIONHeat treatment of galvanized steel (i.e . galvannealing) is carried out at a temperature range of 450°C to 550°C for a time sufficient to convert the free zinc coating to an alloyed one consisting of layers of iron-zinc intermetallic compounds. Table I is a review of the properties of the Fe-Zn intermetallicphases while Figure I is a reproduction - of the Fe-Zn equilibrium phase diagram taken from Hansen.Several authors have studied the formation of intermetallic phases through the interdiffusion of Zn/Fe couples. Their results confirmed the stability of intermetallic phases that could be shown up on the outer surface as a result of galvannealing of galvanized steel.Bernick and Sievertv"" investigated the processing of galvan nealed steel. They found that the galvannealed coating with the best forming qualities consisted of a mixture of Zeta phase and Eta phase."

Jan 1, 1989

By Raymond S. Suglo

Increasing depths of mining coupled with the mechanization of most underground mining operations have led to growing complexities in the mine environments with the production of large amounts of gaseous and particulate contaminants. Over 100,000 lives have been lost due methane gas and dust explosions in coal mine workings in both the US and Canada since 1900 when the methane concentrations exceeded stipulated levels in some workings. There is therefore the need to constantly assess and evaluate the performance of the existing mine ventilation systems to maintain safe and acceptable mine environmental conditions in workings to meet the requirements of federal, state or provincial laws. This paper uses the results of continuous monitoring of methane concentrations conducted in selected development headings in coal mines in North America to assess the effectiveness of existing auxiliary ventilation systems in the control of methane gas concentrations in the headings. The results show that the average quantities of fresh air required to dilute, disperse and remove methane concentrations within set levels of one minute varied from 5.43 m3/s in Heading #11 (Condition 2) to 27.97 m3/s in Heading #10 (Condition 1) and this represented about 12 to 26% of the quantities required to dilute methane concentrations to safe levels within one minute under Condition 1 and 32 to 139% under Condition 2. The average dilution times in the headings studied were less than 8 minutes. The forcing efficiencies of the auxiliary systems in the headings studied ranged from poor to excellent implying that the auxiliary ventilation systems were capable of controlling the methane concentrations below statutory levels but may not be able to cope with large and unusual methane concentrations in the headings. This study is important to prevent methane gas and coal dust explosions in coal mines and thus avoid any loss of lives and property.

May 1, 2001

By James J. Scott

"In the two years since their introduction, Friction Rock Stabilizershave replaced40 per cent of the previously used fixtures in the metal and non-metal mines in the United States. The Friction Rock Stabilizer, or ""Split Set "" , is a mechanical rock stabilizing system which uses friction to prevent rock movement . The Split Set is a tapered, rolled, steel tube that is slotted along its length. As it is driven into a drilled hole smaller than its diameter, it compresses, pre-loading the surrounding rock. This paper discusses the uses and acceptance of the friction rock stabilizer in mines in the United States. IntroductionFriction Rock Stabilizers, commonly called Split Set™· Stabilizers, have been under development by the author and Ingersoll-Rand Company since early 1973. Five years of intensive laboratory and field testing led to their introduction to the metal mines in the United States in the fall of 1976. Actual sales started in February of 1977and, to date, over five million units have been marketed to metal mines. The present rate of usage is near 3 V2 million units per year, which is approximately 50070 of all roof fixtures used in the United States metal mining industry,Richard Hoppe, senior editor of Engineering & Mining Journal. , in an article in the February 1979 issue entitled ""Winning the Battle Against Bad Ground"", said: ""In hardrock mining operations in the western U.S., particularly underground uranium mines where exceedingly difficult ground is common, no roof support system has been accepted more quickly than the Split Set friction bolt invented by Dr. James J . Scott and developed by Ingersoll-Rand Co."" This paper describes how Friction Rock Stabilizers function and presents technical data to show the uniqueness of such systems."

Jan 1, 1980

By Luis A. Tondo

The Paracatu Expansion Project III in Brazil was implemented between 2006 and 2008 to increase the existing capacity from 20 to 61 Million tons per year of gold ore treatment. This expansion led the Brazilian subsidiary of the Canadian Kinross Gold Corporation to become the single largest gold producer in Brazil and the largest single gold concentrator in the world, with a nominal capacity to treat around 167,000 tons per day of ore. This paper describes the Project Development areas for the Paracatu Expansion, using the approach proposed by the Project Management Institute (PMI) and the methodology included in the PMBOK (Project Management Book of Knowledge). The author has more than 20 years of experience in the gold mining industry, having worked as a plant metallurgist, mill superintendent and development manager for RPM until he took the position as the Project Manager of the Paracatu Expansion III in 2005. Luis Tondo has a BSc in Mining Engineering from UFRGS-Brazil, an MScEng from the University of Queensland - Australia and an MBA degree from FDC-Brazil. Luis is currently based in Santiago-Chile, acting as the Project Director for developing projects in Latin America for the Kinross Gold Corporation.

May 1, 2009

Vast quantities of cosmic material, ranging in size from fine dust to large meteorites and planetoids, have been colliding with and accumulating on the earth since its origin 4.5 billion years ago. There are less than twenty well preserved meteorite craters and Jess than thirty fossil craters or astroblemes on the present face of the earth. On the moon, there are approximately 200,000 craters on the visible face alone -the largest crater being 132 miles in diameter and attaining a depth of 16,000 feet. Making allowances for the different physical conditions on the moon and assuming that these lunar features are of impact origin, the indifference is that, since primeval time, large numbers of celestial objects have also encountered the earth, but that both the topographic expression of the impact and the objects themselves have been destroyed by weathering and erosion. It may be reasonable to suggest that additions of cos-mic bodies have materially altered the chemistry of the earth's crust from place to place and that the impact of large meteorites and asteroids has created zones of weak-ness in the crust that could be the center of magmatic intrusion and mineralization.

Jan 1, 1965

By J. Sliwinski, J. Oliveira

"The application of geometallurgy and corresponding sample selection can take on several formats within industry. Current practice can range from a strictly geostatistical approach to one in which geological and metallurgical parameters are used in combination to create a representative sample selection strategy. The stage of a project and the level of information available at the time of sampling influences the methodology used to create a representative sample.A geometallurgical study of Carpathian Gold’s Rovina Valley Project in Romania is used to demonstrate a sample selection strategy that integrates geological, mineralogical and metallurgical data to maximize the relevance of the geometallurgical unit definitions. This approach, practiced by Xstrata Process Support for its’ clients, ensures that the results of the metallurgical program can be interpreted in the context of these units.INTRODUCTIONGeometallurgy is a cross disciplinary approach in which metallurgical performance of an ore is linked to intrinsic geological and mineralogical characteristics. The objective of a geometallurgical study is to characterize the range of metallurgical performance of an orebody. This allows the geoscientist or metallurgist to create a robust flowsheet able to treat the full range in variability and to develop production strategies to maximize financial performance. The standard approach is to individually sample and test a series of ore types or geometallurgical units. Several different approaches are used in industry to define what constitutes geometallurgical units and how to sample them.One current methodology is the use of multivariate statistics. Geochemical data along with available geological data are used to define multiple variability domains (Williams, 2004; Walters, 2009). There are risks associated with this methodology since the extent of the data set itself may not support a purely statistical approach at the time that metallurgical units need to be defined. The assay suite collected by exploration programs is often limited to pay metals while metallurgical performance is often affected by ore gangue components. Furthermore, in many cases metallurgical scoping and pre-feasibility studies take place prior to the availability of extensive geochemical data sets. Purely statistical methods can produce multiple populations which require extensive sampling, testing and validation prior to consolidation into a reasonable number of composites for metallurgical testing. Methodologies are therefore required that allow representative sampling and testing of consolidated geometallurgical composites to occur at various phases throughout the development of a mining project."

Jan 1, 2013

By Ray Mason

Marathon PGM Corporation?s PGM-Cu Project in Northwestern Ontario (Figure 1.0) serves as a case study to describe the process involved in advancing a deposit from grass roots exploration to the completion of several feasibility studies and the parallel commencement of environmental permitting. Through the following examination of historical exploration activities, it is clear that these activities are directly related to economic stimulus, mostly measured by downturns in the mineral industry. Other factors that influence the success of exploration advancing to feasibility and new mine development includes the ownership of the mineral claims, which also changes under these economic influences and the crucial role of interactions between the Company, the Crown and First Nations. The Marathon PGM-Cu deposit is hosted within the Eastern Gabbro Series of the Proterozoic Coldwell Complex, which intrudes and bisects the much older Archean Schreiber-Hemlo Greenstone Belt. The sub-circular complex has a diameter of 25 km and a surface area of 580 km2 and is the largest alkaline intrusive complex in North America (Walker et al., 1993). Mineralization at the Marathon PGM-Cu deposit is part of a very large magmatic system that consists of at least three cross-cutting intrusive olivine gabbro units that comprise the Eastern Gabbro Series of the Coldwell Complex (Figure 3.2.4-3). In order of intrusion, the three gabbroic units consist of (1) Layered Gabbro Series, (2) Layered Magnetite Olivine Cumulate (LMOC) and (3) Two Duck Lake (TDL) Gabbro. The relative size and abundance of the gabbroic units decrease in the order Layered Gabbro Series>TDL Gabbro>>LMOC. Late quartz syenite and augite syenite dikes cut all of the gabbros but form a minor component of the intrusive assemblage.

May 1, 2010

By Charle Lawrence, Murray E. Blanchard

"A significant addition to Canada's commodity export transportation capabilities is being built by Ridley Terminals Inc. on Ridley Island in the Port of Prince Rupert on British Columbia's north coast.Site preparation began in early 1982. By the end of 1983 the terminal will be receiving coal from two major new mines being developed in B. C.'s massive $2.5 billion northeast coal development.The RTI terminal will have initial capacity to transfer 12 million tonnes of coal a year from railcars to storage and to ships. Capacity will be doubled to 24 million tonnes as market opportunities are developed.The challenge of building this $220-million facility in less than 24 months, the benefits Canada has received from the work the project is generating, and the long-term faith in Canada that this project represents, are all part of the excitement which surrounds the Ridley Terminal and northeast coal developments.RIDLEY TERMINALS INC. (RTI) is building a very significant addition to Canada's commodity export transportation capabilities. The facility, on Ridley Island at Prince Rupert, on the north coast of British Columbia, is a key link in British Columbia's northeast coal development which in itself is a massive undertaking involving investment of some $2.5 billion. The entire project is making a substantial contribution to Canada's economy at a time when such contributions are sorely needed.The development is creating employment, not only in British Columbia where its various parts are being created by mining companies, railways and others, but also across the country where suppliers are manufacturing a wide variety of good s and equipment for the development's participants.The RTI terminal is no exception. It is a critical cog in this mega project's large transportation system and its construction is contributing substantially to job creation and to other economic activity, in the Prince Rupert area and in many other parts of British Columbia and the rest of Canada."

Jan 1, 1983

By L. Juteau

"""The north coast of the St. Lawrence River will be the scene of an industrial development during the coming decades"". The facts which underlie this statement are the occurrences of iron and titanium ore, the abundance of hydro-power and the availability of deep-water ports in this region. Havre St-Pierre, Sept-Iles, Port Cartier and Baie Corneau already exist as major ports and urban centers. The huge quartz deposit at Baie Comeau will be a decisive contributing factor in the development of a metallurgical plant in this area. Due to its purity, it lends itself, first of all, to the manufacture of glass of different kinds, being comparable to the quartz sands now used by the plate glass and glass container industries in the Montreal area, Moncton, N.B., Trois-Rivieres and - in the future - at Bécancour, Quebec. However, its high quality will also make it possible to use it as one of the main basic materials for the production of silicon carbide and ferrosilicon, and as a flux in metallurgical processes. It is intended, in this report, to offer conclusive proof of the economical importance of this large quartz deposit by presenting the results of the studies made to date."

Jan 1, 1971