Search Documents

By B. Panton, J. Carvalho, E. T. Brown

"A major consideration in the design of high capacity tiedown anchors for dam, bridge and tower foundations is the tensile resistance of the rock mass to pullout, typically as a result of overturning moments or hydrostatic uplift. Rock mass pullout capacity for installed anchors is developed from the tensile strength and fracture propagation properties of intact rock, the orientation and physical properties of the discontinuities and anchor confinement at depth. The typically assumed, but generally conservative, design approach is to calculate anchor pullout capacity using the dead weight of a uniformly shaped inverted “cone” with an assumed initiation point and breakout angle. In some cases, some tensile or shear strength is considered across the area of the assumed pullout cone, however, these strength estimates are based primarily on based on limited historic testing data, empirical relationships for rock mass strength developed for other applications, and engineering judgement.As an alternative to the current foundation anchor design method, this paper presents a new approach to the rock cone pullout problem using Discrete Fracture Networks (DFN) combined with numerical simulations. The simulations presented in the paper investigate the influence of fractures in a synthetic rock mass on ultimate anchor strength. In addition, the global influence on fracture network statistics on rock mass pullout failure is also discussed and it is contended that some of the aleatory and epistemic uncertainty inherent in the design of rock anchors can be reduced by considering fracture statistics in anchor design."

Jan 1, 2015

By Subrata Dutta

Sindesar Khurd Mine is situated in Rajasthan, India, and operated by Hindustan Zinc Ltd, under Vedanta Group. The base metal mine is high in reserves of Lead, Zinc and silver and has been producing since 2007 with initial production of 0.3 mtpa. Recently the mine has gained prominence as a base metal underground mine in introduction of latest mining techniques and achieving high production at lowest costs. The promising Lead-Zinc reserves of Sindesar Khurd Mine (SKM) and high-tech exploration adopted by Hindustan Zinc Ltd (HZL), (Vedanta Group), raising the reserves and resources from a meager 9 Mt (1997) to 81 Mt (2012), has prompted HZL management to ramp up the mine production from 0.3 mtpa (2006-07) to 2 mtpa by 2013-14 with ambitious plans to reach 3.5mtpa subsequently (presently largest underground metal mine in India). The complete trackless system underground mine, recently equipped with latest leaky feeder communication system (unique in India), utilize modern drilling, mucking and hauling equipment aided with various utility/service vehicles. Excavation optimization and quality recovery maximization from the open and post filled stoping methods, continual expert analysis and feedback from International consultants like AMC (Australia) and SRK (UK), and involvement of renowned bodies in management excellence, have lead the mine towards highest productivity and lowest mine operating cost, earning the mine a prominent place in the global base metal industry. The paper deals with how the various challenges in mine planning and designing, mine development, operator skill, equipment introduction and maintenance, expertise availability, provide training and exposure to officials, prompt and effective communication/service, control of ground vibrations, maintain ventilation standards etc are faced in attaining high operational excellence and thus attain a record mine output/man shift (OMS) of 14 ton/man shift with targets to reach 20 ton/man /shift. Scientific designing using 2D/3D numerical mine-modeling techniques, faster stope sequencing with introduction of paste filling ( first time in India),latest leaky feeder communication system, control ground vibration to stringent standards using electronic delay system, faster raising techniques using raise borers to enhance development and ventilation, cavity scanners to monitor large stope voids, fast shaft sinking at 100 m/month(Chinese expertise) and maintaining adequate ventilation with close software monitoring are some of the highlights discussed in the paper towards achieving the targets.

Aug 1, 2013

By R. Thierbach, W. Kahnt, Oberthür. T., D. Eisenburger, V. Gundelach

ABSTRACT: The ground penetrating radar (GPR) method was used in a platinum mine in Zimbabwe by members of the Federal Institute for Geosciences and Mineral Resources (BGR). The measurements were carried out in boreholes and drifts. Electromagnetic re?ections from a fault that consistently trends parallel to the mineralization zone permitted the mapping of the economically minable parts of the deposit. An introduction is given to the geology of the studied area and the application of the GPR method. The electrical parametres of the rocks are measured in situ, the GPR measurements are displayed with radargrams, and the visible structures are explained in illustrations.

Jan 1, 2010

By R. A. Elliott

This paper describes the development of an infra-red ore dryer at the Mines Branch. The dryer utilizes an infra-red heat source mounted over a stainless-steel belt to dry ores and concentrates of varying particle size and moisture content. It has been found to ?be successful in meeting Mines Branch requirements of minimum dusting loss and ease of cleaning to decrease ,contamination between various batches of dried products. It is described with the hope that it might .prove useful in other laboratories where there are similar problems. It might have an application in the drying of concentrates containing high values where dust losses would result in a considerable loss of revenue; also for small batches of material or an intermittent drying problem.

Jan 1, 1958

By M. R. MacIver, M. P. Pawlik

"An image analysis method based on chord length distributions is applied to the batch settling of polyacrylamide flocculated kaolin suspensions. Two features of the interaggregate void space, the void chord length distribution mean and the white-to-black distribution ratio are extracted from an image series obtained over the two hour settling experiments. This approach produces three signal values, from two different probability distributions that can be measured as an indication of underlying sediment bed density and aggregation state. Further work is required on the physical interpretation of the signal, the image acquisition conditions, and the parameter selection methods. It is suggested that this chord length based feature extraction technique may be a useful signal to monitor during batch settling or thickening.INTRODUCTIONFew in situ techniques are available that can be used to directly measure aggregate properties within sediment beds in thickeners or secondary settlers. Typical process variables monitored include rake torque and height, bed level and pressure, feed rate and density, underflow rate and density, settling rate, and overflow turbidity; yet these process variables are only weakly related to process dynamics (Concha et al. 2014). Additional process monitoring signals, based on the direct measurement of aggregate properties could improve solid-liquid separation control and allow the extraction of more detailed information from batch settling experiments.Several optical methods exist for measurement of moving suspensions of aggregated solids in the dilute concentration regime, such as focused beam reflectance measurement (Peng and Williams 1994), and the turbidity fluctuation method (Gregory 1985). In the more concentrated region of a thickener, acoustic backscatter penetration and attenuation measured with an acoustic probe and changes in the underlying solid concentration in the highly concentrated, near-bed region of a thickener as a function of height and time (Hunter et al. 2012). While machine vision for froth monitoring has been thoroughly studied with at least five commercialized technologies (Aldrich et al. 2010), its’ application to the study of thickening has been limited."

Jan 1, 2016

By R. Drozd

"The Bui/moose Mine is in the northeast coal area of British Columbia, and less than $300 million was spent to bring this 2.3 million-tonnes-per-year metallurgical and thermal coal mine into production by November 1, 1983, one month ahead of schedule. The project is an unincorporated joint venture undertaking, with Teck-Bullmoose Coal Inc., a wholly-owned subsidiary of Teck Corporation, holding 51%, Lornex Mining Corporation holding 39%, and Nissho-lwai (Canada) Ltd. holding 10%. Bullmoose Operating Corporation will be the manager and operator of the project. This paper will broadly cover the history and exploration work on the property, the geology, open-pit mining plans and equipment, the preparation plant flowsheet from breaker station to clean coal silo, the 35 km highway truck haul, the railroad loadout system, manpower requirements, approvals and permits, and general financial arrangements. Introduction The Bullmoose Mine Project is located about 87 km by road south of Chetwynd, B.C. and consists of an open-pit coal mine, a plant facility in the Bullmoose Creek valley below the mine, and a separate rail loadout facility on the British Columbia Railway Branchline near the new town of Tumbler Ridge some 35 km by road to the east. The plant will be capable of producing a total of 2.3 million tonnes per year (mty) of washed metallurgical and thermal coal. Long-term metallurgical coal contracts for high-quality, medium-volatile, bituminous coal have been signed with nine Japanese buyers for 1.7 mty, and the balance of0.6 mty will be for thermal coal production. Plant construction began in the spring of 1982, and in May 1983, preproduction waste and overburden removal in the mine was started. The plant began tuning up in October and was fully operational by December 1983. Metallurgical coal began moving to the coast in unit trains during November, and first vessel loading at the Ridley Island port began in late December 1983."

Jan 1, 1985

By J. Ji

Oxygen requirement during acidic pressure oxidation of sulphide concentrates can he as high as 800 kg/(m3.h) in the first compartment of an autoclave when the total oxidation residence time is shortened to 30 minutes. To achieve such a high oxygen transfer rate while maintaining satisfactory oxygen utilization, a pilot plant campaign was launched at the Placer Dome Research Centre in 1998 to measure the oxygen mass transfer coefficient in a 5 m3 pressure vessel at a total pressure close to 500 psig with a 30 HP gassing agitator. Maximum oxygen flowrate to the pressure vessel was designed at 3 600 kg/h. In this paper, a great deal of information is provided on the gassing agitator, pressure vessel. measurement procedure and results. Without oxygen sparging, the oxygen mass transfer coefficient is 2 600 h-1 with a mixing power input of 5.0 kW/m3 in solution. With oxygen sparging, the oxygen mass transfer coefficient increases to 3 500 h-1 with a mixing power input of 4.0 kW/m3 in solution.

Jan 1, 2004

By W. G. Wahl

The Slave Province, a segment of Archean continental crust, migrated west and north from the northern flank of the Superior protoshield shortly after the Kenoran orogeny. The probable cause of migration, the path it followed and the cause of its coming to rest can be inferred from the Bouguer gravity data. The migration caused an indentation in the edge of the Superior protoshield which precluded the development of the Hudsonian orogenic front under Hudson Bay. As the nickel and asbestos deposits of the Thompson Nickel Belt and the New Quebec Nickel Belt are restricted to this orogenic front, no such deposits would occur under Hudson Bay.

Jan 1, 1973

By D. Bronkhorst, J. Rheault

"Backfill practices at the Williams mine have evolved significantly since underground mining began in 1986. The use of conveyors as a means of transporting fill material to stopes has been discontinued in favour of load-haul-dump equipment. The method of adding binder to the fill product has been refined along with the placement technique. Slurry preparation has been fully automated and flyash is now included as a binding agent. Surface preparation of the fill product has evolved substantially with the quarry operation coming into full operation and the construction of pennanent crushing, screening, and storage facilities. Company personnel have replaced all contracted labour involved in backfill operations. Some changes have been made to achieve a higher standard of quality control while others were implemented as a matter of cost reduction. BackgroundThe Williams mine is one of three mines operating at the Hernlo gold deposit, located 40 km east of Marathon, Ontario, along the north shore of Lake Superior. Daily production at the mine is 6000 Ud yielding an annual gold production of approximately 500 000 oz. The orebody extends from surface to a depth of 1300 m dipping north at 70 degrees. The average orebody width is 25 m, but varies from 45 m on the eastern boundary to about 10 m at the western probable limit and at depth. Proven and probable reserves currently stand at 32 million tonnes grading 6 g/t.The Williams orebody has been divided into four separate mining zones: the A-zone, the West-of-Dyke zone, the B-zone, and the C-zone (Fig 1). Ore production originally was from the A-zone open pit operation while the A-zone and B-zone underground workings were being developed. The mining method employed underground is blasthole open stoping with delayed rockfill. Mining block dimensions are nominally 20 m along strike by 25 m high. Stope extraction is sequenced to achieve a relatively short pillar life and 100010 ore recovery. Pillars are extracted as soon as the adjacent primary stopes are two cycles ahead. Primary stopes are filled with consolidated rock fill after mining. This allows pillars to be blasted right against the consolidated fill, but also requires that the fill be self supporting to a height of 30 m.The Williams mine places approximately 1.4 million tonnes of rockfill and 50 000 tonnes of binding agents each year, with about three quarters of the fill placed being consolidated. The consolidated fill placed at the Williams mine contains Portland cement and flyash as binding agents."

Jan 1, 1994

By Mehdi Razavi

Scope of the Study The possibility and risk associated with mining two stopes at the same time The influence of Creighton Fault on the stability and dilution The effect of irregular shape of stope walls on overall stope stability and ore dilution The support requirements for proposed mining plan

Oct 1, 2010

"In many gold deposits, a reasonable amount of the gold that remains in the cyanide leach tailing is associated with pyrite. Some gold plants have found it economical to incorporate gravity circuits on the cyanide leach tailing to recover the gold bearing pyrite before subjecting it to fine grinding, then recycling the ground pyrite back to the cyanide leach circuit. For low grade gold deposits the loss of gold bearing pyrite is exacerbated as the broader process economics normally favour a coarse grind (> 150 ?m). An option that has received attention over the last decade is to recover the gold bearing sulphides in the milling circuit by gravity, similar to the widely-practiced gravity recovery of free liberated gold. The modelling and simulation of a gravity gold circuit in a milling flowsheet is relatively simple compared with a gold bearing pyrite circuit, as the recycle advantages and breakage functions for gold and pyrite are quite different. This current work represents an attempt to simulate the gravity recovery of gold bearing sulphides in a milling circuit that also incorporates fine grinding, using relatively simple simulation models. The simulation results are further explored with reference to the economics of this type of circuit.INTRODUCTION It is well known that gold is associated with pyrite in most sulphide gold deposits and that the amount of gold associated with pyrite will vary from deposit to deposit. Most of the gold associated with pyrite is liberated in the grinding circuit during the processing of a gold ore. However, some gold remains occluded in the pyrite and is lost in the final leach tailings. Little information is available in the literature on methods to enhance gold liberation from pyrite by specifically removing pyrite, either in the grinding circuit or from the final tailings stream, and grinding it finer. One of the earliest record of this approach is described by King (King, 1949) where pyrite present in Witwatersrand gold ores was recovered by circular jigs and Johnson barrels followed by fine grinding of the concentrate prior to cyanide leaching. Dominy et al., 1970, provides information on the use of Yuba jigs to recover pyrite from the discharge end of ball mills. Again, the jig concentrate was ground to a fine particle size before cyanide leaching to recover the liberated gold. Unfortunately, no information is provided in these articles on the additional gold recovery from implementing these circuits in a flowsheet. Martins et al., 1993, provides details of a gravity circuit using Reichert cones and spirals to recover gold bearing pyrite from a cyanide leach tailings followed by fine grinding of the pyrite concentrate in a Tower mill. The ground concentrate returned to the front end of the already installed leach circuit. Overall recoveries were increased by some 2% to 4% depending on the amount of gold and pyrite in the plant feed."

Jan 1, 2017

By K. G. Thorne, L. J. Cabri, L. R. Fyffe, D. R. Lentz, D. Hoy

"Mineralization at the Main zone of the Clarence Stream gold deposit in southwestern New Brunswick occurs within a parallel series of quartz veins that occupy a NE-trending, steeply north-dipping, brittle-ductile shear zone related to the nearby terrane-bounding Sawyer Brook fault. This deformation zone cuts volcaniclastic sedimentary and volcanic rocks of the Silurian Waweig Formation, and is intruded by mantle-derived East Branch Brook gabbroic dikes and a number of felsic dikes. Intermittent shear-zone reactivation during local magmatic activity induced heterogeneous deformation and alteration of the country rocks and dikes. The terminal phase of shearing is associated with narrow pegmatite-aplite dikes that grade laterally into granophyric granite, and into an auriferous quartz vein. Gold, aurostibite, and gold-antimony intergrowths, predominantly with vein quartz, are associated with a low ƒO2 sulfide mineral assemblage (pyrrhotite, arsenopyrite, and berthierite) that has a sulfur isotopic signature consistent with a magmatic source. Gold saturation and deposition occurred episodically between 300° and 360°C at low activity of sulfur, predominantly in response to pressure reduction during brittle failure combined with the effects of decreasing temperature and sulfidation reactions during fluid-wall-rock interaction. Geochronological studies demonstrate that the timing of the emplacement of the pegmatite-aplite dikes and associated auriferous veins overlap with that of the Early Devonian Magaguadavic granite. Moreover, the composition of the dikes is consistent with their derivation from this granite as late fractionates. The Main zone of the Clarence Stream deposit is therefore interpreted to be intrusion-related, with the Magaguadavic granite being the ultimate source of the gold-bearing fluids. La minéralisation de la zone principale du gisement aurifère de Clarence Stream dans le sud-ouest du Nouveau Brunswick occupe une série de veines de quartz parallèles dans une zone de cisaillement fragile-ductile de direction NE et à pendage abrupt vers le nord apparentée à la faille de Sawyer Brook avoisinante qui délimite deux terranes. Cette zone de déformation recoupe les roches volcaniclastiques et volcaniques de la Formation de Waweig d’âge Silurien et est recoupée par les dykes de gabbro d’East Branch Brook, d’origine mantellique, ainsi que par divers dykes felsiques. La réactivation intermittente de la zone de cisaillement durant l’activité magmatique locale a entraîné la déformation et l’altération hétérogènes des dykes et de l’encaissant. La phase finale du cisaillement est associée à de minces dykes d’aplite-pegmatite qui passent latéralement à des granites granophyriques, puis à des veines de quartz aurifères. L’or, l’aurostibite et les intercroissances d’or et d’antimoine principalement associées aux veines de quartz sont associés à un assemblage minéral de sulfures à faible ƒO2 (pyrrhotite, arsénopyrite et berthierite) présentant une signature isotopique du souffre compatible avec une source magmatique. La saturation en or et la précipitation a eu lieu épisodiquement entre 300° et 350°C dans des conditions de faible activité de souffre, principalement en réponse à la baisse de pression durant la rupture fragile ainsi qu’aux effets de la baisse de température et aux réactions de sulfuration durant l’interaction entre le fluide et l’encaissant. Les études géochronologiques indiquent que l’âge de la mise en place des dykes de pegmatite-aplite et des veines aurifères qui leur sont associées coïncide avec le granite de Magaguadavic, d’âge Dévonien Précoce. De plus, la composition des dykes est compatible avec une origine provenant de ce granite sous la forme de phases fractionnées tardives. Le gisement principale (Main zone) de Clarence Stream est ainsi considéré comme étant associé aux intrusions, le granite de Magaguadavic étant la source ultime des fluides aurifères."

Jan 1, 2008

By Mario Giavani

"IntroductionBy the 1980s, the continuous casting process had almost replaced the ingot casting of steel in Japan, Europe and North America. While economic benefits were probably initially the prime motivator, the transition rapidly proved that continuous casting in conjunction with ladle metallurgy offered a much greater degree of process control and made possible routine steel specifications not previously available.This new technology demanded improved procedures for the quantitative addition of the required metallurgical reagents, especially as regards the more volatile or toxic elements such as calcium , boron, carbon, sulphur, lead and tellurium. The injection of a thin steel tube containing the additive into the metal bath of a ladle refining station offers the best procedure for this. In the industry this has been referred to as ""Cored Wire "".Operators using this technology find that they are faced with balancing the injection speed against the small cross section of the tube to feed the required amount of reagent within the short time span available to the operation. Large-ladle shops requiring major quantities usually resort to multiple machines and high speeds. Many machines approach a maximum feed rate of 400 m/min. Higher speeds exceed the melting rate of the system, and the ferro static buoyancy of the tube will cause it to coil up the ladle wall and possibly resurface into the slag layer, and even eject itself above the surface. Under these conditions, exact control of element recovery becomes difficult, especially with the commonest addition, calcium silicon alloy.Many experts are persuaded that the final melting position of the carrier tube has major importance in establishing consistent element yield to the bath.For instance, the vapour pressure of calcium at l500 °C is close to I bar. Reaching a melting depth sufficient to accommodate this value is considered to be critical to achieving an acceptable and reproducible yield.Many studies have elaborated semi-empirical formulae to establish the melt zone depth, connecting this value essentially to the diameter of the tube , the injection rate and the superheat of the steel. The author's experience in steelmaking could not confirm such formulae in many cases, and he set about to develop a mathematical model which would be useful in addressing this problem, taking into account the several parameters which will regulate the behaviour of a filled tube immersed in molten steel."

Jan 1, 1991

By V. N. Rampton, C. F. Gleeson

"Exploration results over three overburden drilling anomalies defined by the Ontario Geological Survey in 1981 in the Kirkland Lake area, Ontario are presented. The anomalies come from lowland areas where overburden is thickest. By mapping the bedrock and surficial geology, by prospecting, humus sampling and shallow till sampling over the surrounding upland surfaces, one can initially evaluate such overburden drill anomalies without costly reverse circulation drilling. The drilling should follow, if necessary, only after surficial base data has been obtained. Preliminary work on these three properties has defined the presence of at least two styles of gold mineralization. One occurs in silicified zones in intermediate volcanics closely associated with northwesterly trending faults and shear zones. The second occurs in quartz-carbonate alternation zones in volcanics intruded by quartz-feldspar porphyry dykes. IntroductionThe three examples presented in this paper present first-hand information on an approach to the follow up of several geochemical anomalies that were found by the Ontario Geological Survey when they carried out reverse circulation overburden drilling as part of the Kirkland Lake Initiative Program (KLIP) in 1980 (Routledge et al., 1981). The initial approach is relatively simple, systematic, and cost and technically effective. It readies the properties for further exploration, or conversely, it could downgrade the properties as viable gold targets."

Jan 1, 1987

In most instances, the preferred mining methods in steeply dipping narrow vein deposits are selective methods such as cut and fill or shrinkage. The main advantage of these methods lies in the higher degree of control over dilution that can be achieved. However, where ore body geometry lends itself to it, high yield bulk methods can also be attractive. Higher productivity (and the associated lower costs) and lower worker exposure are some of the significant advantages that have made such methods so popular. The Lapa gold mine located in North-Western Quebec uses the long hole mining method (with cemented rock fill) very successfully despite challenging ground conditions. This paper focuses on the experience of the mine with regards to drilling and blasting practices. Firstly, the reasons that prompted the selection of this mining method at Lapa are examined. Secondly, the challenges that the difficult ground conditions found at Lapa pose to drilling and blasting are discussed. Finally, the results of trials of different drilling and blasting strategies that were performed at the mine are presented with particular emphasis on the lessons learned.

Aug 1, 2013

By Charle Pelley, Kosta Fytas, Peter Calder

"A computer model has been developed which is capable of evaluating alternative production schedules (long- and short range) of an open pit mine once the ultimate pit limits have been defined. The model user can choose the best alternative according to cash flow considerations and the particular mining conditions. The model involves a combination of simulation for long range production scheduling and linear programming for short range scheduling. IntroductionMining of mineral deposits in such a fashion so that, at depletion the maximum possible profit is realized, has been a very old problem of the mineral industry. In the past, when high-grade ore reserves were readily available and profits were very high, no question of optimum profitability was raised.However, recently the complexity of both open pit and underground mining has been increased tremendously. The additional problems of continuously rising production costs on one hand and of depressed metal prices worldwide on the other, have been demanding optimum profitabiliy from every mining venture .Particularly in the area of open pit mining, the sequence of ore and waste extraction has now become very important since the size of the pits and of the mining equipment has increased enormously. The process of open pit mining involves a continuous change of the open pit surface and there are many feasible plans of extraction which lead to the same final pit shape (ultimate pit limits). Each of these feasible plans generates a production schedule over the entire mine life, which mayor may not be optimal."

Jan 1, 1987

By H. Westengen

The AE alloy family exhibits remarkable combinations of properties when utilized as high pressure die castings. This performance relies on the fact that the rapid cooling rate resulting from the direct contact between the molten alloy and the steel die walls effectively refines the structure through rapid solidification. Furthermore, the rare earth additions modify the solidification pattern, dramatically reducing the solidification interval. A solid shell forms at temperatures exceeding 500C, reducing the tendency for die sticking and inverse segregation. As a result, the die castability is excellent, giving parts with a smooth and shiny surface. Unlike other magnesium die casting alloys developed to improve elevated temperature creep properties, AE alloys do not suffer from the commonly observed tendency to introduce brittleness. This feature is attributed to the fact that the massive magnesium- aluminium intermetallic phase is substituted by a finely dispersed lamellar structure of Al-RE intermetallics. The resulting combination of excellent elevated temperature properties and good ductility, as well as excellent corrosion resistance, means superiority of these alloys for demanding automotive engine and chassis applications.

Jan 1, 2006

By John Kruse, Sethu Raman, Dave Tenney

The Cullaton Lake B-Zone gold mine was the first gold producer in the Kaminak Subprovince of the Canadian Shield . Located approximately 650 km north of Thompson. Manitoba, the mine produced 77,783 ounces of gold and 5,564 ounces of sil ver from 251 ,236 tons of ore during 1981-84 period. The depos it is a small , structurally controlled , stratabound orebody in an Archean iron formation. Most gold occurs in sulphide and silicate fac ies. Based on new ev idence, the depos it is interpreted to have fo rmed by remobilization of syngenetic low-grade gold mineralization in the iron fo rmation in a favoura ble fold structure. The concept and methods developed at the mine have been successfull y applied in the discovery of new deposits in the area. One of the concepts. which link Archean and Proterozoic mineralization. may have wider applications in the search fo r gold deposi ts elsewhere in Canada .

Jan 1, 1986

By A. A. Nourbakhsha

The main application of refractories based on andalusite in ferrous metallurgy are in air heaters of blast furnaces, mobile mixers, and hot-metal transfer, pig iron ladle, steel-casting, and intermediate ladles. Three specific properties of andalusite are very interesting for the production of high-quality shaped and unshaped mullite refractories: being free of water, its crystal a remains stable without changing its density or volume after firing and therefore has no internal porosity .Graphite additives due to its great wetting ability play an important role in raising the property of refractory bodies. In order to improve properties of andalusite graphite bodies, oxidant agent for increasing in hot strength and oxidation resistance can not be avoided. In this research, firstly 8 pig iron ladles from ESC(esfahan Steel company) with different conditions selected and monitored during usage to determine of main factors affecting on corrosion of refractories. Results showed that tap to tap time, undischarged pig iron ,penetrated pig iron are the main ones.Literature studies showed that the graphite addition help to thermal shock resistance and liquid penetration(steel,pig iron) effect. In this research particle size distribution of aggregates containing andalusite and graphite determined by andreazen equation. Then different mixes with different percentage of graphite,Si, FeSi, SiC prepared by uniaxially pressing under 1500kgf/cm2 pressure by adding 4%wt novalak resin and 0.4%wt HMTA as hardner. Samples fired at 1100-1500oC under reduction atmosphere. According to specific standards density, porosity and CCS measured. Analytical tests such as XRD, SEM were carried out on sample selected from point of view of mechanical properties at different temperatures. Results showed that optimized amount of Si and Fe-Si for _-SiC formation in body is 4 and 6 %wt respectively at 1500OC. XRD and SEM analysis on sample with Fe-Si additives showed no destructive phase through the matrix, also SiC additives not only increase oxidation resistance but also no effect on thermo-mechanical properties.

Oct 1, 2011

By Y. Buro

The Bachelor Lake gold deposit occupies an ESE-trending, SW-dipping, silicified shear zone with hematitic alteration. It transects NE-trending, steeply dipping Archean volcanic formations and the O'Brien granite. Major W-SW and N- NE-trending faults have affected the ore zone and the emplacement of the granite intrusions. Movements along the WSW set may have opened the fractures filled by the mineralization. Gold is generally associated with pyrite. Its source, whether a granitic pluton or a volcanic sequence, is undetermined, but the granite probably provided the concentrating mechanisms through heat and hydrothermal solutions.

Jan 1, 1984