Search Documents

By J. L. Bowlby

TWO years ago, at the annual meeting of this Society, the writer presented a paper dealing with various aspects of the water problems existing in the Cape Breton coal-mining area. Much of that paper was of a theoretical nature, in that an attempt was made to get at the fundamental principles underlying the problems, in order to establish a sort of background against which future results could be laid. Up to that time, only Central power plant in Glace Bay had been under observation, and, since the work had been in progress only a year, it was recognized that there were strong possibilities that certain variations in procedure might have to be introduced as w; became better acquainted with our problem. We were by no means certain that we had covered all the facts of the case. The present paper will therefore be of the nature of a progress report, rather than a formal contribution to the Society. Subjects of a theoretical or academic nature will be avoided as far as possible, attention being confined chiefly to the results obtained during the past two years. In looking over the work with low-pressure boilers, there are certain general conclusions that can apparently be safely drawn. Wherever possible, proper operating conditions will be expressed in terms of appropriate units. Absence of corrosion in boilers where the alkalinity has been maintained within the pH range 11.0 to 11.4 forces one to the conclusion that these are safe working limits. Previous experience had shown that corrosion would occur if the alkalinity were much reduced. Higher alkalinities are un-necessary, more expensive, and are said to introduce the possibility of pitting. We made no attempt to obtain quantitative data in respect to pitting. It is said to occur at pH 12.0. Consequently, conditions of alkalinity were main-tained well below this figure. In the above paragraph, the pH range 11.0 to 11.4 applies to boiler waters which have received the lime and soda treatment. The general practice, when this treatment is employed, is to use 1.0 lb. lime to 7.0 lb. washing soda. At Central power plant, soda-ash is at present substituted for washing soda, the equivalent proportions being kept the same. But not all the plants are on the lime and soda treatment. At Waterford Lake, a 1: 1 mixture of soda-ash and trisodium phosphate is satisfactorily employed, and in Sydney Mines and at No. 3 power plant in Sydney, good results are being obtained at a somewhat greater cost with a commercial phosphate treatment.

Jan 1, 1936

By R. P. van Hille, N. Mooruth

Remediation of acid rock drainage (ARD) was performed within a linear flow channel reactor (LFCR) via a floating sulphur biofilm (FSB). A full sulphur species material balance was conducted in order to characterize the sulphide oxidation. The reactor was able to achieve an 82% and 93% conversion of sulphide with a hydraulic residence time of 2 and 5 days respectively. 92% and 55.5% of the converted sulphide reported to the biofilm as sulphur for the 2 and 5 day residence times respectively. The mass transport limitations within the biofilm were identified via a dissolved oxygen gradient profiling system.

Jan 1, 2011

By Michel Garon

"Several years ago computer control of the flotation process was successfully implemented at the Matagami concentrator of Noranda Mines Inc. At that time this was the first computer application being installed at this operation. The last few years have seen an extensive use of programmable controllers in areas such as the copper and zinc dewatering circuits and the lime preparation system. With the aid of such instruments, these areas have attained a high level of automation and as a result, a high degree of efficiency. The controllers have proven to be very dependable and easy to use.IntroductionThe Matagarni Division of Noranda Mines Inc. operates two mines in the Matagami District of northwestern Quebec which is located about 650 km northwest of Montreal. The mines ship ores to a central concentrator whose throughput averages 95,000 tonnes of ore per month. Metal contents of the mill feed average 0.9 per cent copper and 5.0 per cent zinc. Concentrate outputs are approximately 3,200 tonnes of copper and 8,200 tonnes of zinc per month.The concentrator commenced operation in 1963. An on-stream X-ray analyzer was installed in 1968, providing analyses of several samples in the flotation circuit without the aid of a computer. In 1974, control of the circuit by computer was added to the system. As a result, zinc flotation efficiency improved considerably and reagent costs decreased through the reduction of copper sulphate consumption.In the past few years it was realized that significant improvements could also be made in other parts of the operation . Copper and zinc dewatering circuits and the lime preparation system were identified as major areas that could drastically benefit from automation. In 1982, programmable controllers were seriously considered as an attractive alternative for achieving the company 's goal. Because of their relative lowcost and their high degree of flexibility, they were selected for implementing automation and, for improving the efficiency in each of these areas."

Jan 1, 1985

By Peter Barker, Terry Jones

"The Kelsey Centrifugal Jig (KCJ) utilizes the application of centrifugal force (and the resultant enhanced gravitational field) to conventional jigging technology principles to successfully and efficiently process materials where the valuable constituent particulates are very fine and/or where there is a small specific gravity differential between these and the gangue minerals.The KCJ is applicable to a broad range of fine mineral recovery duties, with current installations in the mineral sands, tin, tantalum, gold and nickel industries. Other areas of application are being developed with mineral commodities including tungsten, base metals, iron ore, chromite and apatite/feldspar.Information on the principles of operation of the KCJ, typical performance figures in a number of application areas, comparison to centrifugal concentrators, key elements for a successful KCJ operation and recent developments with the KCJ are presented in this paper to demonstrate the capabilities of the KCJ.INTRODUCTIONAfter a number of years of development by inventor Chris Kelsey, the first commercial KCJ unit was installed at the Renison Bell tin mine in Tasmania, Australia, in 1992. The subsequent decade saw the installation of further KCJ units in applications including tin, tantalum and mineral sands.Development and improvement in KCJ hardware continued and culminated in the introduction of the high-capacity Model J1800 KCJ and standard features such as an automatic screen cleaning system. This opened up further markets and resulted in Model J1800 KCJ installations in the gold and nickel industries, as well as further KCJ installations in the mineral sands and tin industries. In recent years, work has continued on application of the KCJ to many other duties in industries including tungsten, base metals, iron ore, chromite, apatite/feldspar, etc."

Jan 1, 2007

By Douglas A. Karvonen

"Competition in the world potash market has increased significantly since the late 1970s. The failure of consumption to grow at expected levels has led to industry over-capacity, a situation which is likely to persist at least until 1990. Individual Saskatchewan producers and their offshore marketing company, Canpotex, have responded to this challenge by increasing mining efficiency, developing more cost-effective and reliable transportation systems and establishing innovative financing and market development programs tailored to customers' special needs. Investment in warehouse facilities to serve U.S. customers and exploration of opportunities for intermodal distribution through the Great Lakes and the Mississippi River system have maintained individual producers' position in the highly competitive domestic market.Export sales through Canpotex have been bolstered by utilization of CIDA funds, Exp ort Development Corporation financing guarantees and other innovative payment plans which enable heavily indebted developing countries to maintain the import levels which are necessary for their agricultural development.IntroductionPotash is the general term applied to various potassium salts both natural occurring and commercially derived. The most common of the commercial product s are potassium chloride, potassium sulphate and potassium magnesium sulphate. The potassium content of potash is measured in units of K20 equivalent. The common grades of potassium chloride produced for agriculture average at least 60 0/0 K20 compared with approximately 50% Kp for potassium sulphate and 22% for potassium magnesium sulphate."

Jan 1, 1985

By K. E. Waters, J. E. Nesset, F. Rosenblum, J. A. Finch

An advanced laboratory-scale weathering apparatus has been developed at McGill University to study the effects of weathering (ambient temperature oxidation) on the self-heating of sulphides. Previous work by the authors has shown that the problematic self-heating of sulphides is inherently linked to the degree of oxidation (weathering) of the minerals: un-oxidized active sulphides exhibit little or no self-heating while the same material when weathered can generate extensive self-heating bringing temperatures well above 100 0C. In this study the effects of environmental conditions (weathering time, ambient temperature, sample moisture, relative humidity, and oxygen content) were evaluated with respect to the self-heating response of a pentlandite-pyrrhotite nickel sulphide concentrate.

Jan 1, 2015

By R. A. Horn, S. M. Telfer

"Canada has a per capita GDP second only to Japan among the G7 countries and a positive trade balance which ranks third among the world's major economies. International trade represents a very large part of the national economy and as a proportion of GDP is larger than that of all the other G7 countries with the exception of Germany. On the negative side the Canadian current account deficit relative to the size of the economy is significantly worse than that of all major industrial countries, due mainly to the cost of servicing an immense foreign debt and to a large and worsening negative trade balance in manufacturing.The outflow of money may be reduced by increasing the productivity and competitiveness of those sectors of the economy in which Canada already has a leading competitive position and which have the potential for further growth. The mining industry is uniquely qualified in this respect in that Canada is the western world's largest producer of metals and mineral products and has the geology and the exploration skill to replenish reserves assuming that an adequate level of investment is maintained. In 1989 the minerals industry contributed $8 billion to the country's balance of payments and with the exception of forestry is the only sector of the economy which has shown consistently increasing foreign earnings over the long term.In recent years there has been a decline in exploration in Canada and a significant increase in countries such as Chile. The demand for hard currency to finance the development of the newly emerging capitalist economies of the CIS and Eastern Europe is also driving these countries to seek foreign investment to allow them to exploit their natural wealth more efficiently. Canada is therefore facing growing international competition for risk capital and in the future its trade surplus will probably decline in the face of lower cost foreign production.Canada rightly exercises a high level of environmental control on its mining operations; however a significant deterrent to investment is the fundamentally unjust application of the many provincial and federal environmental laws, under which a mining company, even if it takes every measure to protect the environment, runs the risk of eternal and unlimited future liability. If this situation is not rectified the effect will be an increase in global pollution as mines in countries with more lax application of law and regulations controlling environmental damage replace those of Canada. Tax benefits and incentives are a more efficient means than arbitrary regulations in minimizing environmental damage."

Jan 1, 1994

By N. P. Hristov, L. V. Kuzev

"A simulation study of the fill factor of a drum mill was conducted using two types of grinding media: balls and tetraballpebs. Each medium was composed of equal number of grinding bodies having equal weight but different shape. The difference was in the density of the two grinding media.Standard spherical grinding bodies (balls), which were used in practice, and equivalent (by weight) grinding bodies in the shape of spheroidal tetrahedrons (tetraballpebs) were studied. The simulation was conducted in a module of a 1.2 m diameter drum mill, whose length exceeded twice the diameter of the corresponding grinding body. The grinding balls had a few percent (3 to 6) higher fill factor than the grinding tetraballpebs in the same shell.Vertical sections of the grinding medium were taken across the studied shell module along its axis. They showed the location of each grinding body in the fill volume. Defects in the packing of the grinding bodies and the contacts between them and with the inner surface of the shell were also show. Differences in the contact points of the balls and the tetraballpebs were noted. For the tetraballpebs, we observed contacts both between the spherical surfaces and with the edges and vertices of the grinding bodies.The topography of the grinding media is shown visually.INTRODUCTIONThe grinding balls have been studied extensively. It is the traditional grinding medium in ore processing industry. The parameter characterising the grinding medium is its density. It is the mass of the grinding medium per unit of volume. The parameter may have a range of values. It depends on:• The physical properties of the material they are made of;• The shape of the grinding body;• The dimensions of the body;• Size distribution of the grinding bodies in the grinding media.In comminution, the fill factor of the mill shell is the process parameter that is representative of the grinding medium. Some publications have indicated the disadvantages of ball grinding. For example, Wu, Xiang, Glen, and Duan (2008) note in the analysis of the mechanism of grinding that the balls are not the best grinding media and disadvantages include among others:• Easy over-grinding resulting from the point contact between the balls;• Attrition surface is the smallest in the grinding media;• Poor selective exposure of minerals resulting from the accidental and often significantly more powerful impact on the feed;• The grinding efficiency drops as the fineness of grind is increased;In the Handbook of mineral processing, Polkin (1950) noted that the shape of the grinding bodies determines the volume of the void spaces therein and therefore the shape affects the grinding efficiency per unit of volume of the grinding medium."

Jan 1, 2016

By Ngonidzashe Chimwani, David Glasser, Diane Hildebrandt

"Milling circuits play an important role in achieving the desired product; tonnage, size distribution and properties, since they are directly linked to the comminution energy consumption for the whole process. A grinding model with a mathematical simulation was developed for an open milling circuit with a scalped feed from a hydro-cyclone. The circuit was optimized by determining the optimal conditions in terms of energy consumption which would produce a floatable product having a desired size range (i.e. -75 +9 µm) for a platinum-bearing ore. The simulation results showed an operating region comprising the best combination of the ball filling and mill speed to achieve the highest production of a floatable size class, with the minimum energy consumption.INTRODUCTIONBall milling is usually conducted in closed circuits in order to achieve a desired product size without material overgrinding. The technological importance of optimising milling circuits cannot be overemphasised (Toneva and Peukert, 2007). Previous work has brought significant insights into the benefits of modelling milling circuits (Austin et al., 1984; King, 2012; Toneva and Peukert, 2007). However, the ability to model these circuits is dependent on the performance of the classifiers and the fidelity of the grinding mill model used compared to the actual circuit (Toneva and Peukert, 2007). Austin et al. (1984) identified five types of milling circuits as shown in Figure 1 namely; the grinding circuits employing mill in an open circuit, normal closed circuit, reverse closed circuit, open circuit with scalped feed, and, the combined closed circuit. Depending on the presence of the first classifier, the second, or both as well as their corresponding loops (streams), the combined circuit (e) can reduce to; an open (d), a normal closed (b), an open circuit with scalped feed (c) or a reverse closed circuit (a). In the case of an open circuit, the mill is operated without being directly influenced by a classifier. The normal closed circuit does not have the first classifier and therefore the make-up feed is the actual feed stream. Conversely, the reverse closed circuit keeps only the first classifier. The open circuited with scalped feed has only the first classifier but does not have the second one. The overflow stream from the classifier is mixed with the mill product to form the final product for the downstream process."

Jan 1, 2016

By Fiona Campbell

"Modern history is full of breakthroughs in technology, all striving to increase productivity and efficiency. What are the elements that should be taken into consideration in the design and implementation of modern automation systems in a control room? Both industry and international standards are now demanding that Human Factors be considered as part of the design of control rooms to maximize efficiency and minimize the potential of human error which can lead to downtime and a loss of profit as a result of interruptions in production. As the current workforce ages and the younger generation matures, this is also becoming a key element when planning a control room. New standards are helping to address some of these challenges that are facing the mining industry today. With an increased focus on the operator, an intelligent and ergonomic workspace can both mitigate risk and optimize production. Optimization is money. We will examine how to analyze and implement innovative control room planning to maximize mineral processing production and minimize risks that can impact overall production and profit.INTRODUCTIONIn this day and age, optimization of production in an industrial environment is becoming more and more of a challenge. With ever changing technology as well as other external factors, this can be especially daunting. There are several key elements that may not be immediately obvious when planning a control room design or renovation, most notably the role of the human in this environment. Fatigue, stress, distraction, reaction times and situational awareness are all critical in a 24/7 environment. With the growing need to include human factors when considering and designing an optimal work and production environment, it is becoming even more important to design a control room that can address as many of today’s challenges as possible.The standard definition of the word “optimization” is “an act, process or methodology of making something (as a design, system, or decision) as fully perfect, functional or effective as possible.” (www.merriam-webster.com). If we apply this to business, what it really means is finding the most cost effective way to achieve the highest level of performance while considering constraints, both external and internal, by maximizing the desired factors and minimizing undesired ones. Sometimes, however, we can get caught up in the day to day processes, without taking a moment to step back and objectively review what it is we need to achieve, and more importantly, the steps that can facilitate our success."

Jan 1, 2016

By A. G. Roach

Introduction The plant described in this paper is located at Coniston, Ontario, the smelting centre of the former Mond Nickel Company. Coniston is situated some eight miles east of Sudbury on the main line of the Canadian Pacific railway and on the Toronto-Capreol branch of the Canadian National-railways. The plant is now under control of the International Nickel Company, as a result of the merger of the two companies in 1929. The smelter proper includes four 50-in. by 240-in. blast furnaces and five 13 ft. by 30 ft. converters, and has a capacity of about 65,000 tons of ore charge per month. As accessories to the smelter there are a mill, where some 10,000 tons per month of low-grade ores are concentrated, and the sintering plant, which is the subject of this paper. The present 6-unit sintering plant replaces a former 4-unit installation. Here, fine ores, concentrates, and flue-dust are sintered on Dwight-Lloyd machines, the sinter produced being charged into the blast furnaces. At the time of writing (1931), only the concentrator is operating at capacity, due to present world conditions.

Jan 1, 1932

By József L. Margitfalvi

Different Au/MgO catalysts modified with Mn, and Fe were prepared by precipitation-deposition. The catalysts were characterized by XRD, FTIR, Temperature Programmed Reduction (TPR) and CO chemisorption and were tested in CO oxidation in the temperature range of 243-523 K. The catalytic tests using both Temperature Programmed Oxidation (TPO) technique and time on stream (TOS) experiments revealed the high activity of catalysts prepared. In TPO experiments the modification by Mn significantly increased the activity above 300 K, however in the subambient temperature range the activity decreased considerably. Catalysts modified by iron did not show any decrease in the activity below 300 K, while the activity at high temperature increased significantly. Catalysts modified by Mn, Fe showed higher activity, selectivity and stability in preferential CO oxidation, carried out in the presence of hydrogen than the unmodified Au/MgO catalysts. Results of in situ FTIR spectroscopy on both the base Au/MgO and the iron modified catalyst unambiguously revealed the formation of ionic gold in the presence of CO/O2 mixture. The formation of this species was strongly hindered in catalyst modified by manganese. Results obtained strongly support the need for the formation of "metal ion - metal nanocluster" ensemble sites. These sites are involved in the activation of the CO molecule prior to its reaction with atomic oxygen. It is suggested that at subambient temperature these ensemble sites contain mainly ionic forms of gold, while at higher temperature iron or manganese ions are involved in CO activation.

Oct 1, 2003

By W. H. MacLean, S. Liaghat

Abstract- The Key Tuffite is a thick (0.3 m to 6 m) and laterally extensive (-10 km) cherty, sulfide-bearing tuff unit in Archean greenstones in the Matagami mining district in northwestern Quebec. It lies at the contact of the Watson Lake Group and overlying Wabassee Group volcanic rocks, and is host to major Zn-Cu volcanogenic massive sulfide deposits. The tuff component is highly altered and its volcanic precursors are not identifiable by petrographie means. The tuff is mixed with a volcanic exhalative component comprising chert, carbonate and sulfides (pyrite, pyrrhotite, and minor sphalerite and chalcopyrite). The normative mineral composition of the Key Tuffite is 33% quartz, 28% sulfides, 16% sericite, 8% carbonate, 60Jo chlorite and 9% other minerals. In the vicinity of the Bell Allard and Orchan mines, the precursor tuff components are identified using immobile major and trace elements, as Watson Lake tholeiitic rhyolite (Zr/Y = 1.5 to 3.5, LaN/Ybn. = 1.7 to 2.8, Si02 = 72.5 ± 1.2 wt %, and Wabassee calc-alkaline andesite (Zr/Y =9, LaN/Ybn. = 4 to 8, Si02 = 56% to 65%). Immobile element computation techniques were used to calculate mass additions and losses in the conversion of the tuff to the Key Tuffite. Average net amounts of Fep3 (27% total iron), Si02 (14%), CaO (8%), S and K20 ( + 2%), were added, Na2O was removed (-2.8%), and MgO was over-all unchanged. Total net mass change was +63%, which comprises mainly exhalative additions, but also includes changes owing to hydrothermal alteration of the tuff component.

Jan 1, 1992

By D. M. Maijer, S. L. Cockcroft, A. B. Phillion, P. Fan, C. Reilly

"A numerical model has been developed to study macrosegregation associated with liquid feeding in the Low Pressure Die Casting of A356 aluminum alloy wheels. The model of the wheel casting process has been implemented within the commercial CFD software package, FLUENT, using a User Defined Function (subroutine) to account for Si rejection based on the Scheil approximation. The model has been validated against temperature and microstructural data taken from a commercially cast wheel. The amount of segregation in the wheel has been shown to be significant in a couple of key areas. The implications of accounting for segregation include an improved ability to predict shrinkage porosity, fatigue performance and potentially also hydrogen porosity.INTRODUCTION The aluminum alloy A356 is widely used in the automotive and aerospace industries for various components. Examples include automotive wheels, automotive suspension components and airframe castings. Focusing on automotive wheels, Low-Pressure Die Cast (LPDC) A356 wheels offer significant design freedom and are far more aesthetically appealing to consumers than conventional stamped steel wheels. A356 wheels now dominate the market, appearing in all but the entry level offerings of the OEM manufacturers. However, they are typically over-designed to allow for the various casting related defects that degrade their mechanical performance. Thus, their potential to save weight has not been fully realized. Wheel manufacturers are under constant pressure to ensure their products meet strict mechanical requirements (ductility, fatigue, vibration), tight geometric tolerances and high aesthetic quality. The mechanical properties of the final product are determined by the microstructure – e.g. SDAS – and the defect population (porosity and oxides). Depending on their size and location, both porosity and oxides, can act as crack initiation sites reducing fatigue life (Caton, 2001; Jordan, 2010; Wu, 2015). There are a number of examples appearing in the literature (Atwood, 2000; Carlson, 2007; Lee, 2001; Yao, 2011) of numerical models that have focused on hydrogen-based pore formation that have demonstrated an ability to predict porosity formation and pore size distributions in geometrically simple castings. These models assume that the local gas species diffusion through the liquid metal to the pores is the rate-controlling factor of pore growth. Another common source of porosity is liquid encapsulation (Dantzig, 2009). As the pressure within the isolated liquid drops, pores form first due to the pressure dropping below the equilibrium partial pressure of hydrogen in solution and then second grow substantially as the pressure continues to drop falling below the vapour pressure of Al. One factor that can affect both mechanisms of pore formation is species macrosegregation, which has received comparatively little attention in die-casting."

Jan 1, 2017

By Ross Nairn

"Tulawaka Mine is a joint venture between Pangea Minerals Limited 70% (a wholly-owned subsidiary of Barrick Gold Corporation) and Northern Mining 30%. Tulawaka Mine is located in North West of Tanzania in the Lake Victoria Goldfields. Tulawaka Mine is scheduled to process 360,000 tonnes per year at an average 11.5 g/t head grade over a 4 year mine life.The Tulawaka Process Plant uses single stage crushing, single stage SAG milling, gravity, intensive leach of gravity concentrates, CIL, Zadra desorption and cyanide detoxification to process the ore. Gold recovery exceeds (or is expected to) 95%.The Process Plant was designed and constructed under the supervision of Ausenco Engineering of Australia. Site works commenced in January 2004, Process Plant construction commenced in July 2004 and the first ore was presented to the Process Plant 26th February 2005. The first gold was poured on 15th March 2005. All construction contractors were demobilized from site 7th April 2005. Major achievements have been 3.4 million hrs LTI free during construction and operation to date, training of the Tanzanian workforce at Bulyanhulu Mine prior to commissioning, a succession plan to replace expatriate personnel with Tanzanian staff and significant over performance of the Process Plant against design.INTRODUCTIONTulawaka Mine is situated approximately 160 km south west of Mwanza in the western Lake Victoria Goldfields District of north western Tanzania. The property is held under a joint venture between Pangea Goldfields Inc (70%), a wholly owned subsidiary of Barrick Gold Corporation, and Explorations Minieres Du Nord Ltée (30%). A location map showing the position of the operation in Tanzania is shown in Figure 1.Mine site staff at Tulawaka comprises a combination of Tanzanian and Expatriate personnel. All Pangea personnel live on site and commute to their place of residence for their R&R on a 9 weeks on 4 weeks off roster."

Jan 1, 2006

By D. Turk, P. Lefebvre, J. Sargent, K. Major

"Stillwater Mining Company recovers platinum and palladium from their Nye Montana operations. Mining first commenced at Nye in 1987 at a milling rate of 455 t/d (500 stpd). The plant was expanded in 1995 with the replacement of the ball mill and the addition of flotation capacity to increase mill throughput to 1820 t/d (2000 stpd). The applications for platinum and palladium have increased in recent years particularly in the automotive industry and the supply of the metals has remained fairly constant with prices for both platinum and palladium increasing and remaining very stable. In 1997 Stillwater initiated the expansion of their operations to increase production of platinum and palladium. Projects were initiated to expand production at the Nye operations, increase smelter and refining capacities at the Columbus facilities and to develop the extension of the orebody at the East Boulder site. This paper will discuss the changes at the Nye concentrator which were completed to increase production from 1820 t/d (2000 stpd) to 2730 t/d (3000 stpd) and eliminate some of the process bottlenecks.IntroductionStillwater Mining Company is mining the only significant primary source of PGMs outside of South Africa. The J-M Reef is an extensive mineralized zone containing PGMs that has been traced over a strike length of about 43 km (27 miles) in the southwest region of Montana. Stillwater controls the entire PGM mineralized zone.Johns-Manville geologists discovered palladium and platinum in the early 1970’s. In 1979, a Manville subsidiary entered into a partnership with Chevron, USA to develop the project. In 1 987, operations at the Stillwater property near Nye, Montana commenced."

Jan 1, 2000

By D. Kulchyski, R. Thibault, D. Lamoureux

"Mine tunneling applications are sensitive to the leakage and friction performance of ducting systems. Improvements in performance can help project economics through reduction in drift height, booster fan spacing, fan electrical power requirement, and deferral of ventilation raise construction. Semirigid plastic ducting has enjoyed significant adoption in mine tunneling in recent years. This paper explores technical properties and performance aspects of this relatively new material application.INTRODUCTIONUnderground mining projects are sensitive to mine development cost and schedule to meet first production—both of which are defined to a substantial extent by mine access construction. The very nature of mine access development requires driving accesses into new areas and even mechanized and automated tunneling methods require ventilation. Until underground airways are connected, allowing a flow-through circuit, ducted ventilation is required to establish ventilation within any single-access (i.e.: dead-end) heading. See Figure 1 as an example of ducted ventilation. Improving performance of ducted ventilation systems impacts project cost and schedule in several ways:For drifts whose height is defined by overhead clearance above haul trucks or tall equipment, smaller diameter ducting will decrease heading size.With higher ventilation flows, activities can be less ventilation-constricted; secondary headings can be worked without restriction, which improves schedule.Given the ability to provide more air for a given fan power, blasting gasses can clear the face and mine more quickly so crews can return to work more quickly - allowing higher advance rates.Lower electrical costs – both due to lower power consumed by fans and with the requirement for fewer electrical stations to power booster fans."

Jan 1, 2019

By Gurinder Kaur

Selenium (Se) based materials find wide applications in rectifiers, solar cells, photographic exposure meters, data storage devices, xerography and anticancer agents. They are also used in the glass industry to eliminate bubbles and remove undesirable tints produced by iron. In addition, Se is highly reactive towards a wealth of chemicals that can be potentially exploited to convert Se into other functional materials such as CdSe, ZnSe, Ag2Se. Here, we report a review of structural investigations of Se based materials in glassy and nanostructured forms. Glasses having varying amounts of Se and Tellurium (Te) were doped with group IV and V elements such as antimony and tin. Structural changes accompanying the composition variation were characterized with x-ray photoelectron spectroscopy, differential scanning calorimetry and x-ray absorption near edge spectroscopy. At the same time Se-Te nanoalloys were synthesized in aqueous micellar phase using Na2SeO3/Na2TeO3 as the Se/Te source. Morphology change from nanoparticles to nanoribbons was investigated using Scanning and Transmission Electron Microscopy (SEM/TEM) techniques. Structural investigations were also done for well defined morphologies of Se based nano-biomaterials obtained in the presence of water soluble protein bovine serum albumin (BSA).

Aug 1, 2013

By H. Bouzahzah

Sulfidic tailings, subjected to atmospheric water and oxygen action, can generate acid mine drainage (AMD); which is the most important environmental problem facing the mining industry. AMD generating potential can be assessed by the static tests which consist of a screening method where the neutralization potential (NP) and the acid-generating potential (AP) of a given rock sample are determined. The AP and NP are determined separately in the different static test existing procedures which can be divided into two distinct classes: chemical and the mineralogical methods. For some chemical method, the AP is calculated on the basis of total sulfide sulfur content in the sample which may overestimate its AP if significant quantities of non-sulfide sulfur species are present (e.g. organic S in coals, some sulfate as gypsum, barite, etc.). However, the mineralogical method evaluates the AP by the sum of the individual sulfides participation on acid generation based on their concentration within the sample and can be more accurate than the chemical method. For AP calculation, the Paktunc (1999a) mineralogical static test takes into consideration all sulfide minerals occurring in the sample. However, it does not take into account the rates of acidity production of these sulfides submitted to weathering conditions. So, the present study focusses on the modification of Paktunc AP calculation by considering the acidity production rates of these minerals. To reach this objective, five base-metal sulfides (pyrite as reference, chalcopyrite, sphalerite, arsenopyrite, galena), diluted within quartz (25?75 wt.%) simulating mill tailings were subjected to a kinetic test to evaluate their AP. The results show that all the studied sulfides minerals generate acidity at different rates, so the Paktunc?s equation for AP calculation has been adapted accordingly.

Aug 1, 2013

By S. J. Cook

The subject of capital and the Canadian mining industry is so broad as to be impossible of comprehensive treatment in brief form. The purpose of the present paper therefore will be only to outline in a meagre and somewhat sketchy way the nature and extent of the mineral industry in Canada and to point out those features which are likely to be of general public interest. Canada's mineral industry has a long and creditable production record. The? value of the output per capita rose from $2.23 in 1886 to a maximum of $26.40 in 1920 and the value of the products from ten million dollars in the former year to almost two hundred and twenty-eight million dollars in 1920. Compared with other primary industries and on the basis of the value of production, mining held third place in Canada in 1920, the premier position going to agriculture and the value of forestry production placing that industry second in the list. In the mineral industry, between six and seven thousand properties are operated annually giving employment to up- wards of sixty thousand employees to whom about seventy-five million dollars is paid in salaries and wages. During 1923, seventeen mineral products reached a production value of one million dollars or over in Canada and in order of the values assigned these were: coal, gold, nickel, cement, cop-per, silver, clay products, lead, asbestos, natural gas, stone, zinc, lime, cobalt, sand and gravel, gypsum and salt.

Jan 1, 1924