Search Documents

By Eiichiro Mizushima

Catalyst systems comprising (Ph3P)AuCH3 and acid co-catalysts were found to be highly efficient for hydration of alkynes to give ketones. Methanol was the best choice of solvents. Introduction Hydration of carbon-carbon unsaturated bonds is one of the environmentally benign routes to the carbon-oxygen bond formation. Hydration of alkynes forming carbonyl compounds, an important variation in this category, is a well known reaction which has been extensively studied. The reaction by acid-catalysis is the most conventional method, while it is applicable only to electron rich acetylenes to obtain satisfactory yields (1,2). The hydration of simple alkynes usually requires another catalyst (co-catalyst), typically a mercury(II) salt (3), which is inconsistent with the guiding principle of Green Chemistry (4).

Oct 1, 2003

By Dale A. Sketchley

The objective of Quality Assurance and Quality Control programs on advanced exploration projects is to ensure that data from sampling, assaying, and recording of geological observations are of high integrity for the purpose of obtaining reliable mineral resource and reserve estimates. National Instrument 43-101 Standards of Disclosure for Mineral Projects states that all scientific and technical reports must be prepared and certified by a Qualified Person in accordance with professional and industry standards following Mineral Exploration Best Practices Guidelines and Definitions, and Guidelines of the CIM Standards on Mineral Resources and Reserves. Additional information is given in Companion Policy 43-101CP and Technical Report Form 43-101F1. Although the Qualified Person must discuss and describe the Sampling Method and Approach; Sample Preparation, Analyses, and Security; and Data Verification; there is little specific information in the guidelines on Quality Assurance and Quality Control programs. Examples from the Oyu Tolgoi Cu-Au Project are given for optimizing sampling protocols, following proper sample preparation procedures, safeguarding sample shipments through chain of custody, ensuring quality of assaying with Round Robin monitoring programs, verifying transcribed data, and validating data with check assays to ensure high integrity for resource and reserve estimation. Oyu Tolgoi, also known as Turquoise Hill, is in the South Gobi desert, Mongolia, about 550 km south of the capital city of Ulaanbaatar, and 875 km northwest of Beijing, China. The project covers a major copper-gold system, which consists of the South West, South, Central, and Far North deposits, comprising high sulphidation and porphyry mineralization with oxide, supergene, and hypogene ore types. Exploration is done by multiple diamond drill rigs, and samples are prepared on-site and shipped to laboratories in Mongolia, Canada, and Australia for further preparation and analysis.

May 1, 2003

By J. M. Menacho, J. M. Reyes

"Batch and continuous regrind tests were conducted in 3 kW and 15 kW tower mill units, respectively. Single particle size classes of a chilean copper sulphide concentrate were employed in the batch tests, while a fraction of the plant stream was deviated to the continuous unit operated under different conditions.Results are interpreted in terms of the simplified grinding kinetic model energy-based and conveniently adapted to this application. Based on the above figures plus some industrial data supplied by MPSI Inc., a scale-up relationship was developed for the apparent specific rate of breakage siE, as a function of the net power draw P, i.e.siE = siE text (P/P test) 0.089This equation fit very well the available data at the three scales and its application to regrind 4400 t/day of rougher copper concentrate from 70% below 325 Tyler mesh to 95% below same mesh, involves around 30% energy-saving compared to standard ball mill for same grinding task.INTRODUCTIONImpact and abrasion-attrition breakage are two extreme mechanisms present in any grinding system in a proportion defined by specific design and operating conditions. Impact breakage is generally efficient for coarse grinding, while abrasion-attrition is adequate to produce fine particles. Efficiency of conventional tumbling mills decreases as fineness of the product increases, even though distribution of applied stresses is always much stronger than internal force distribution in the particles. On the other hand.in a vertically stirred ball mill like the tower mill, distribution of applied stresses and particle strengths are in the same order of magnitude, making possible nearly ideal abrasion conditions (1).Tower mill configuration includes a cylindrical body vertically mounted and provided with a central screw with flights to produce circulation of balls moved up through the inner region to return down by the external space. Fresh material can be fed into the top , center or bottom in order to assure appropriate agitation of suspended particles. Size reduction and evacuation rates should compensate settling of coarse particles to avoid sanding of the screw. Detailed description of the tower mill and its operation have been given elsewhere (2),(3)."

Jan 1, 1989

? The Mining Association of British Columbia (MABC) was established through an Act of Parliament in 1901 ? The MABC represents the interests of B.C.?s ? Coal and mineral mining companies ? Smelting companies ? Advanced stage development projects ? Key areas of work: ? Environment, Health and Safety ? Policy & Government Relations ? Knowledge and Information Services

May 1, 2008

By K. Zenger, J. Kaartinen, J. Huuskonen, S. Torttila, S. Lähteenmäki, J. Pietilä

"Pyhäsalmi Mine in Finland has a long history of continuous process development. The concentrator processes Cu-Zn-sulphide ore with high recoveries. An on-line flotation simulator has been developed to maintain and further improve the flotation performance. Consisting of a flotation kinetic dynamic model, and interconnected with process control software, the simulator can be used for training new control room operators in various scenarios. For daily operation, the model parameters are continuously adapted to take into account the changing process conditions. On-line simulator tracking the process can provide the process operator new information in several ways: a) values of unmeasured process variables are obtained by displaying the corresponding simulator values, b) predictions of future process states and outputs are calculated and displayed, c) information of changing process parameters can be used as an indicator of e.g. change in the processed ore type. This paper describes the adaptive simulation system and its usage at the Pyhäsalmi concentrator.IntroductionPyhäsalmi massive sulphide orebody is located in central Finland. Operation of the mine started in 1962 and it is currently producing copper (Cu), zinc (Zn) and sulphur (S) concentrates. The concentrator control and optimization system has a long history of successful continuous development during the past decades (see e.g. Huuskonen & Moilanen, 2010). An on-stream analyzer has been a part of the automatic process control since 1968 (Lähteenmäki, Miettunen & Saloheimo, 1999). First control algorithms based on a flotation mathematical model were developed in 1971 (Koivistoinen & Miettunen, 1985). In 1990’s the development of a froth machine vision systems started (Kaartinen, 2009; Kaartinen, Roine & Hätönen, 2009). More recently Pyhäsalmi Mine Oy has been involved with several national development projects dealing with particle size distribution measurements (Kaartinen & Tolonen, 2008), spectral analysis of flotation slurries (Haavisto, Kaartinen & Hyötyniemi, 2008), and dynamic simulation of flotation processes. The latter topic is further elaborated in this paper."

Jan 1, 2015

By Don Thompson

Canada’s oil sands are a controversial topic and virtually every newsmaker and layperson seems to have an opinion about this 179 billion barrel resource. The oil sands represent 97 per cent of Canada’s remaining oil reserves, but misinterpretation and misrepresentation of the facts are threatening development of a resource that generates significant employment and tax revenue for Canadians. Join Don Thompson, president of the Oil Sands Developers Group, as he dispels the top ten myths about Canada’s oil sands and presents an alternative perspective on an industry that can play a critical role in North America’s economic recovery.

Jan 1, 2010

By E. Dernedde

Industrial plants located in the province of Quebec, Canada, are subjected to large variations of the ambient air temperature, Building ventilation systems of these plants must have some flexibility in order to meet industrial hygiene standards (TLV for chemical substances, heat stress and cold stress) at any time of the year, The building ventilation of a bath treatment plant of an aluminium smelter in Quebec was examined under summer and winter conditions, Part of the plant has periodic emissions of hydrogen fluoride gas and heat from hot anode butts, CFD modeling was used to optimise the building ventilation of the bath treatment plant, The present study proposes a modified building ventilation system, which improves the internal environment, complies with industrial hygiene standards and also reduces heating costs by 20 % during winter.

Jan 1, 2005

By V. L. Gravitis

Radioisotope X -ray techniques of analysis for nickel have been tested in laboratory and plant trials. In the laboratory tests. a comparison was made of radioisotope and conventional analyses for nickel in solid s samples taken from streams of a nickel concentrator. Coefficients of variation of 1.7% for feed and concentrate samples , and equal to 10% for final tailing samples, were obtained. Continuous determination of nickel in final tailing slurries was demonstrated in a trial lasting 20 days at a nickel concentrator (Western Mining Corporation), nickel being determined with a standard error of 0.036% Ni in the slurry solids within the range of 0.24 to 0.68% Ni. This error, obtained by comparison of on-stream probe analyses with assays of samples taken from the stream, includes errors in sampling and assay by conventional techniques.

Jan 1, 1977

By Marc Arpin

La Bolivie possède tout pour réussir. Son vaste territoire de plus d'un million de km2 et qui occupe une position stratégique au coeur du continent sud-américain recèle des ressources naturelles (forêts, minéraux, gaz naturel, etc) variées et abondantes. Elle a une frontière avec pas moins de 5 pays dont le géant que constitue le Brésil ainsi qu'avec l'Argentine, l'autre puissance régionale. Pourtant, malgré tous ces atouts, la Bolivie demeure l'un des pays les plus pauvres du continent. Ce paradoxe n'est nulle part mieux reflété que dans le secteur minier. Celui-ci fait face à une situation de crise en dépit d'une tradition minière de plus de quatre siècles et d'un potentiel géologique indiscutable ayant conduit à la découverte et à l'exploitation de fabuleux gisements d'argent et d'étain. Les habitants des districts miniers vivent dans des conditions de pauvreté extrême et les indicateurs de développement humain de ces régions sont parmi les plus bas en Amérique du Sud. La Bolivie réussit difficilement à attirer les compagnies minières alors que, chez les voisins, et particulièrement en Argentine, qui n'a pas de tradition minière, les investissements miniers majeurs affluent. Dans cette conférence, nous chercherons à expliquer les causes de cette situation et proposerons des solutions possibles.

May 1, 2001

By Martin Plante, Denis Hamel, Marie-Pier Bédard, Jeff McLaughlin

"The results and methodology for the optimisation of the zinc flotation circuit at the Matagami Mill using the 6-Sigma methodology are shown in detail while only the base line and final results are presented for the copper circuit. As a result of the six sigma project, the zinc concentrate grade was improved by 2% and the zinc recovery by 3%, with reduced dosage of reagents while the copper concentrate was improved by 2.4%. The process variation in the zinc concentrate grade and recovery was also reduced by over 50%. The main factors contributing to the project success were identified to be improvement in the plant measurement systems, an internal benchmarking exercise and statistically designed laboratory and in plant tests to guide the process improvement. The annual value to Noranda resulting from this project has been estimated at approximately $5 million.INTRODUCTIONThe Matagami concentrator started ore processing from the new Bell- Allard deposit in July 1999. Concentrator performance (grade and recovery of zinc and copper concentrates) was highly variable and work was ongoing to fix the sources of variation. In the mean time, Noranda embarked on its 6-Sigma initiative across the company. The 6-Sigma DMAIC (Define, Measure, Analyse, Improve, Control) methodology was used in the two flotation circuits to reduce variation and improve performance. The statistical 6-Sigma methodology moves towards identifying and controlling critical process operating variables (the X' s) to achieve customerspecified performance (the Y's). The goal of the methodology is to describe a process in a numerical equation known as the transfer function, given as Y = f (XI, X2, X3.. .), where Y could be concentrate grade or recovery and examples of X's are reagent dosage, particle size, etc. With the transfer function, optimal operating conditions and control tolerances are established for the key X's to ensure the desired Y performance is obtained.Each phase of the 6-Sigma methodology is explained below with examples from the Matagami project."

Jan 1, 2001

By Y. S. Sun, Northeastern University, W. B. Li, P. Gao, Z. Y. Zhang, J. W. Yu

"The boron-bearing iron concentrate was extracted from ludwigite ore by the process of magnetic-gravity separation. In order to fully utilize the refractory ore and meet the boron consumption of China, a novel process for separation of boron from iron in boron-bearing iron concentrate was proposed in this paper. In particular, laboratory scale experiments of improving boron reactivity were performed. Fine boron-bearing iron concentrate briquettes were reduced by bituminous coal completely at 1125 °C for 150 min. The effect of sodium carbonate, which was used as an additive in the roasting process, was investigated. The addition of sodium carbonate decreased the boron reactivity and facilitated the volatilization of boron. The influence of diverse cooling methods of the reduced samples on the boron reactivity was studied. The results indicated that boron reactivity could reach up to 80.76% when the reduced samples were cooled by rapid water quenching. In addition, the magnetic material containing 92.71 % Fe with a recovery of 95.11 % and boron-rich non-magnetic material containing 14.51% B2O3 with a recovery 88.85% could be obtained by low-intensity magnetic separation. The magnetic material and boron-rich non-magnetic material were good raw materials for steel-making and borax production, respectively.INTRODUCTION Ludwigite ore is abundant in Liaoning province of China, with 28.43 Mt B2O3 accounting for 57% of the boron resources of the country (Liu et al., 2006). However, it has not yet been utilized on an industrial scale due to its complex mineralogy and fine mineral dissemination (Wang, Wang, Ding, Ma & Xue, 2012). At present, boron-bearing iron concentrate and boron concentrate can be obtained from ludwigite ore using magnetic-gravity separation. The boron concentrate contains B2O3 12%~16%, which can be used as a high-quality raw material for the boron chemical industry after activated roasting, but the B2O3 content in the iron concentrate reaches up to 4%~6%. In order to further separate boron and iron from boron-bearing iron concentrate, a blast furnace and a solid pre-reduction followed by electric arc furnace melting have been proposed (Liu, Cui & Zhang, 1998; Wang et al., 2012). However, both of these two current routes face the same crucial problem that molten boron-rich slag has to be cooled slowly to obtain the alkali-dissolution activity of boron, which affects the yield of boron resource."

Jan 1, 2016

By Norma G. González

La littérature et notre expérience en Bolivie dans une communauté minière très divisée comme celle de Huanuni nous montrent le besoin d?envisager des négociations gagnant-gagnant entre communauté et entreprise minière, non pas comme un point de départ, mais comme un résultat à atteindre, qui nécessite la préparation de conditions préalables. Cela implique fondamentalement de mettre l?accent sur le processus qui permettrait par la suite aux parties de mieux traiter les questions de contenu. Suivant cette hypothèse générale, l?initiative conjointe entre le Ministère des ressources naturelles du Québec et le CECI ?Développement des mécanismes de négociation entre communauté et entreprise minière? peut dégager, après un an et demi d?expérience pilote dans le site minier de Huanuni, département d?Oruro, Bolivie, les leçons préliminaires suivantes. Ce processus requiert: ??Agir, en tant qu?organisme consultant tierce partie, selon des principes et une méthodologie qui relèvent de la Communication publique et de la Médiation ; ??Comprendre et agir à partir de la ?réalité sociale? des parties en présence: l?entreprise minière, l?État et les différents groupes de la communauté; ??Intervenir sur les ?réalités sociales? des parties, par des actions d?éducation et de diffusion dans le but de préparer les personnes, les institutions et les organisations de la société civile, à des changements durables du modèle de communications existante; Approfondir la compréhension de la ?réalité sociale? du conflit (la culture du conflit, les méthodes populaires de résolution des problèmes et de gestion des conflits) afin d?offrire aux bénéficiaires les technologies appropriées pour la transformation de cette culture de confrontation violente en gestion constructive des conflits. Par ricochet, nous espérons ainsi faciliter l?attraction des investissements dans le secteur minier.

May 1, 2001

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, D. K. Fountain

"As part of a larger research program, a number of MEGATEM airborne electromagnetic (EM) test flights were flown over the Gallen massive sulfide deposit in northwest Québec. A particularity of this test site is that a major part of the ore body was extracted before the MEGATEM survey. Therefore one of the purposes of this study was to verify the ability of the system to detect the remaining massive sulfides below the water in the open pit. The open pit is also surrounded by a metallic fence, and a power line is present in the vicinity. A large part of the case study involved accounting for the impact of infrastructure and acidic water on the survey, which will help in the interpretation of airborne EM responses in complex exploration situations.The Gallen deposit was also previously flown with the INPUT and GEOTEM airborne EM systems before the major exploitation period. A comparison between the results from the different survey results allows estimation of the physical properties of the Gallen deposit, which is a relatively poor conductor.A new method for removing the power line signal shows amplitudes with a smaller residual associated with the emanating fields, and more compact, cleaner responses associated with induced currents. This will make it easier to identify bedrock conductors close to power lines"

Jan 1, 2007

By N. V. Mel'nikov

This paper discusses the reserves of oil, natural gas and coal in the USSR, with particular attention to the future role to be played by coal in supplying the energy fuel resources of the country.

Jan 1, 1972

By L. M. Nolan

Chemical Mechanical polishing, or CMP, has four components in the polishing interface; namely the polishing pad, the polishing fluid, the abrasives in the fluid, and the surface being polished. Understanding the way that load is transferred between these components is key to understanding and predicting wafer polishing. Numerous models of CMP and the different load sharing arrangements which occur between these four components have been proposed. These include models by Luo and Dornfield (1) and Fu, Chandra and colleagues (2). Other models focus on just one or two loading arrangements, such as `hydroplaning' when all load is transmitted by the liquid in the case of Runnels and Eyman (3). In this work, we consider four possible combinations of load transfer from pad to wafer in CMP. These combinations are listed below in Table 1 and are illustrated schematically in Figure 1. It is important to note the role of scale in this process; the illustrations in Figure 1 are drawn to scale from actual profilometer scans obtained over a length of 5 with particles of 150 nm in diameter. Table 1 - Load Transfer Combinations Load Regime Illustration Wafer - Fluid - Pad Figure la Wafer - Particles/Fluid - Pad Figure lb Wafer - Particles - Pad Figure lc Wafer-Pad Figure ld The interest in load-sharing between the system components is because some configurations are anticipated to achieve higher polishing rates than others. For instance, in hydroplaning, or hydrodynamic lubrication, the lateral force exerted on the polished surface by the particles can be no higher than the fluid shear force developed in the gap between the pad and wafer. This is not expected to generate high rates of material removal from the surface (4). For contact that is largely between the pad and the wafer, such as the regime depicted in Figure ld, the lateral load is transmitted to the wafer by the pad and is hence limited by the pad's low rigidity. This regime is not expected to generate high material removal rates either. The highest levels of material removal are expected from regimes where the mechanical load exerted on the system is transmitted by the particles, in combination with either the fluid or the pad. Under what circumstances does the polishing regime change from one to another? What must occur in order to initiate or terminate contact between the system components? This is an ongoing question in the field of tribology, and has traditionally been viewed in terms of the pressure and velocity applied to the system, the thickness of the fluid film between the two surfaces, and the roughness of those surfaces (4). In this paper, we propose a new mechanism ? that the load on the particles may be sufficient to totally embed them in the polishing pad, at which point they are no longer able to transmit load and polish the wafer surface. This is illustrated schematically in Figure 1(d).

Jan 1, 2010

By D. J. Cheung, V. N. Kazakidis

ABSTRACT Seismicity and rockburst problems in hard-rock mines negatively impact safety and profitability. The authors propose a design risk methodology as a relative risk assessment for underground excavations vulnerable to rockburst damage. It considers rock mass conditions relating to mininginduced stress, geological structure, rock mass properties, and mining influence. Application of the methodology to rockburst cases involving seismically active fault zones at the Craig mine in Sudbury, Ontario, Canada, demonstrates that design changes can reduce exposure and economic risks. Mines with high geotechnical risk can use the design risk methodology to evaluate design alternatives as a risk management strategy.

Jan 1, 2014

By B. P. Simser, R. K. Brummer, A. Mortazavi, P. P. Andrieux

"A large-scale panel destress blast was fired at Brunswick mine in the fall of 1999 in order to reduce the ground stresses in a critically important neighbouring mining region. This work, sponsored by the Mining Division of CAMIRO and Brunswick mine, consisted in heavily choke-blasting — and subsequently leaving in place — a massive waste sulphide pillar in the southwest end of the 1000 m level. This paper describes the approach and design methodology used to try to maximize breakage in the rock mass in the area to destress, while minimizing damage to critical infrastructures in the vicinity. The loading operations, as well as the results of the blast — in terms of its field performances, as recorded by near-field blast vibration monitoring equipment, visual postblast assessments and measured impact on the regional stress field — are discussed as well. A brief comparison between the measured stress changes and inelastic numerical modelling of the test site is also presented.Un tir à grande échelle de relâchement des contraintes dans un pilier a été effectué à la mine Brunswick à la fin de l’automne 1999 dans le but de diminuer les contraintes de terrain dans une très importante zone de production adjascente. Ces travaux, financés par la division minière de CAMIRO et la mine Brunswick, consistaient à tirer violemment sans aucune face libre, et à laisser en place, un pilier de sulphures massifs au sud-ouest du niveau 1000 m. Cet article décrit l’approche et la démarche conceptuelle utilisées pour tenter de maximiser les fractures dans le pilier visé, tout en minimisant les dommages collatéraux à des infrastructures critiques se trouvant dans les environs immédiats. Les opérations de chargement des explosifs et les résultats du tir — en termes de ses performances, telles qu’évaluées par de l’équipement de monitoring rapproché des vibrations de tir, d’observations visuelles, et de son impact sur les contraintes de terrain locales — sont également discutés."

Jan 1, 2003

By Michael J. Lord, Richard H. O. Wagner

"The technologies used in the mineral processing of ores are being increasingly applied to the identification and remediation of metal contaminated industrial, military and landfill sites. The objective of mineral processing treatment of contaminated site material is to restore the value of the land and to concentrate the contaminants into a very small volume of separated material which, depending upon its nature, can be further processed, marketed, or sent to a landfill. A systematic characterisation of the site material is first undertaken. Bench and pilot testing follows to evaluate criteria for metal separation. The testing may examine one or more physical or physico-chemical reprocessing methods, singly or in combination, for the remediation of the test samples. These mineral processing tests determine the % metal removal fiom the soil and the contaminants concentrated from the medium. The usefulness of mineral processing testing for site remediation flowsheet design and execution is illustrated by the case studies presented. This paper will present the test results of three case studies: an industrial site decontamination, the cleanup of a small arms firing range, and the reclamation of property within a landfill.INTRODUCTIONEnvironmental legislation and our society’s quest for a cleaner environment has led to the application of mineral processing expertise and technology for industrial site decontamination, military site cleanup and landfill reclamation. Although the required level of decontamination varies between jurisdictions, a site becomes a candidate for decontamination once the contaminant concentrations are found to exceed the Canadian Council of Ministers of the Environment (CCME) Interim Remediation Criteria for soil (decommissioning guidelines) or applicable provincial guidelines. The objective of mineral processing treatment of contaminated site material is to restore the value of the land and to concentrate the contaminants into a very small volume of separated material which, depending upon its nature, can be further processed, marketed or disposed of in a landfill"

Jan 1, 1999

By A. L. Karyakin

The report focuses on the process measurements of the mass of rock in the bucket power shovels and dragline excavators. The mathematical models are suggested of AC and DC electric drives of excavators. These models are a basis for calculation methods of the electric drive electromagnetic torque. The design schemes of mechanical equipment of excavators considered to account the situation of bucket in the plane of the boom. The methods of static moment allocation and identification of the excavator technological operations are developed. The results of the work are experimentally tested on power shovels with bucket capacity of 12 and 18 m3.

Aug 1, 2013

By John De La Vergne, Morri Medd

"This paper describes the sinking of a circular concrete ventilation shaft through 110feet of water-bearing overburden. The brine circulation freezing method was used to stabilize the walls during excavation. In order to take advantage of the cold winter weather, a custom-built heat exchanger (natural radiator) was installed in place of the standard mechanical refrigeration plant.IntroductionIn the late fall of 1979, Les Mines Selbaie awarded a contract to the firm of 1.S. Redpath Limited to sink a ventilation shaft on its property in northwestern Quebec. The shaft was to be sunk through 110 feet of water-bearing overburden and approximately 90 feet of rock to a final depth of 200 feet below surface. The water table was measured at 16 feet below the surface elevation.After examining the soils report and diamond drill core from the shaft area, Redpath came to the conclusion that freezing was the best way to stabilize the overburden for sinking. LocationThe mine site is 420 statute miles due north of Toronto, just east of the Ontario/Quebec border (Fig. 1). Access to the site is provided by a development road built by the Quebec government from the Matagami/lames Bay Highway. History of Ground Freezing In the Mining IndustryIn 1862, shortly after the development of mechanical refrigeration, a mine shaft was sunk through an artificially frozen water-bearing formation in the United Kingdom. The first application of ground freezing in North America was for a Michigan iron ore shaft in 1888. Since that time, the freezing method has been used to sink hundreds of shafts throughout the world. Its best known application was to sink sixteen shafts through the Blairmore Formation in Saskatchewan.The same method has been used in every case. It involves chilling a calcium chloride brine solution and circulating the brine in concentric pipes, spaced between 3 and 6 feet around the shaft perimeter and usually 4 to 5 feet from the limits of the proposed shaft excavation."

Jan 1, 1982