Search Documents

By D. T. White

"Metallurgical extraction processes often call for the heating of aqueous slurries. Indirect heat exchangers are generally not feasible for service with high yield stress slurries because of low heat transfer rates. It is more appropriate to heat the slurry by direct contact, typically with steam as the heating medium. Although having a long and successful history, direct-contact heat transfer to aqueous slurries has been used without the support of pilot plant research. This paper provides results of the needed research, the work being done at a scale large enough to enable direct scale up to commercial operations. A pilot plant heater was constructed and tested to develop an understanding of the slurry heating process and to ensure that commercial scale heaters were appropriately sized.INTRODUCTIONPressure Leaching OperationsPressure leaching operations are often used to oxidise sulphide gold ores, or for extraction of nickel and cobalt from laterite ores with sulphuric acid. Where there is sufficient sulphur available, the exothermic pressure oxidation reactions can be self sustaining at temperatures as high as 225 ºC, without having to preheat the feed slurry. At lower sulphur levels, slurry preheating is required. This is typically achieved by utilising the flash steam released from the slurry letdown stages and contacting this directly with cold incoming slurry ahead of the autoclave. The vessels where this slurry-steam contact is made are known as heaters or condensers, with the number of pre-heat stages varying, depending on how much heat is evolved in the oxidation reaction (Mason, 1990).In nickel laterite pressure acid leaching processes, which operate between 245 and 270 ºC, the only significant exothermic reactions are those associated with dilution of sulphuric acid in the leach. As a consequence, slurry preheating with flash steam is always used commercially. In practice the number of flash steam preheating stages required varies from 1 to 3, driven by a number of factors, including other uses for flash steam and the upper temperature limit at which preheated slurry can be pumped. A diagram of a typical pressure acid leach train is shown in Figure 1.For pressure acid leaching operations and at low sulphur levels in pressure oxidation, boiler generated direct steam addition to the autoclave is required to sustain the reaction temperature. For this reason it is imperative that the flash steam – slurry heat transfer is efficient and the slurry temperature approaches that of the flash steam closely."

Jan 1, 2012

By Z. Tang

A collaborative project was performed between NRC Institute for Fuel Cell Innovation and MagPower Systems Inc, to develop a cost effective fabrication process to manufacture the anode for magnesium-air fuel cell with improved performance. A novel fabrication process was developed, which resulted in a porous microstructure with increased surface area, instead of the traditional solid structure. This porous anode greatly increased power density in the magnesium-air power source. This fabrication process is very simple and cost effective. Especially, this process makes it convenient to incorporate different alloying additions, as well as hydrogen inhibitor and electrolyte management additive into the anode. The anode composition was designed so that micro galvanic cells were formed as current is drawn out of the fuel cell, and resulting increased dissolution rate of Mg. It is feasible to incorporate hydrogen inhibitor and electrolyte management additive into the porous anode, and the anode with some kinds of inhibitors exhibited improved electrochemical performance. This paper describes the microstructure and electrochemical performance of anodes with designated porous structure and alloying additions. Furthermore, quantitative kinetics analysis of the obtained I-V curves and electrochemical impedance spectroscopy were carried out to clarify the mechanism.

Jan 1, 2005

By J. F. Shirley

"Very seldom, if ever, is a molybdenite by-product plant operated exactly the way the process design engineer visualizes it. The best thing the design engineer can do is provide a sound, basic circuit with enough room and flexibility in order that the operating staff can make the necessary modi fi cations to optimize the process. The plant, with minor modifications, should be capable of handling more than one process. This is especially true when the client is having the plant designed for a new process.The writer would like to propose the following ten ""rules-of thumb"" for designing by-product molybdenite plants where the molybdenite is floated out of a copper concentrate. The term rules-of-thumb is used, because there are probably valid reasons for not using one or more of them in a particular plant design. In fact it was 1980 before the writer was all owed to start up a plant where all of these rules were honored in the plant design. This was after 19 years of experience in the design of molybdenite by-product processes and plants. The main reasons for not following the rules are available capital, available space, and the client's experiences based on pilot plant and laboratory test results."

Jan 1, 1981

By Andreas Gaich

COMBINED 3D IMAGES _ Highly detailed 3D geometry _ Identification of fine fractures together with a general impression of the situation _ Dealing with unfavourable outcrop geometries

May 1, 2009

By Louise Pearce

?Environmental and social impact assessments (ESIAs) are: ??process-driven and scientific processes ??The process entails a number of steps and procedures which result in obtaining a licenceto operate ?and moving more towards a social license to cooperate. ?However, the primary premise of ESIA is to facilitate the consideration of environment and the communities in planning and decision-making which would ultimately make it possible to arrive at decisions that are ?sustainable?. ?Hence, ensuring the development of the mining sector on a sustainable basis is a critical challenge that needs to be addressed by the global community.

May 1, 2011

By R. H. Walton

"In recent years the recovery of copper from low grade oxide ores has received widespread attention. The cost of treating such ores using conventional technology, such as milling and flotation, is frequently prohibitively high and copper recovery is generally low. The introduction of heap leaching, solvent extraction (SX) and electrowinning (EW) has resulted in high recoveries, good copper cathode quality and low production costs. This technology has now been successfully applied on a worldwide basis.This paper reviews the various process and design options and gives approximate capital and operating costs for a 1.0% copper ore.INTRODUCTIONAs a result of the low copper prices that prevailed for much of the last two decades, aggressive attempts were made by the industry to cut operating costs. Under such circumstances heap leaching, solvent extraction and electrowinning, to recover low cost copper from oxide ores, has received particular attention and ultimately widespread acceptance.Low grade copper ore (typically containing less than 1.0% Cu), which could not be economically treated by other methods, is placed on heaps and leached with dilute solutions of sulphuric acid. The copper rich, pregnant solution, drains from the heap into a collecting pond and is pumped to a solvent extraction plant where it is purified and upgraded. The resulting solution, termed the pregnant electrolyte, passes to the electrowinning section where the copper is recovered as high grade cathodes and sulphuric acid is regenerated, (Figure 1).This paper specifically describes the processing of copper oxides. Other copper minerals such as chalcocite and chrysocolla are also leached by dilute solutions of sulphuric acid. In practice the oxide minerals are frequently associated to varying degrees with less easily leached sulphides, such as chalcopyrite. In some cases, once the oxidized capping of the ore body is removed, the oxides are totally replaced by more refractory sulphides. Under these circumstances the leaching recovery is significantly reduced. However the principles described here for solvent extraction and electrowinning are also applicable to solutions received from heaps containing sulphide minerals, which are leached more slowly and involve bacterially induced reactions."

Jan 1, 1990

By H. J. McQueen

Pressure welding is a solid state joining technique that depends on bringing the parts into sufficiently close contact that inter-atomic bonds are achieved. Pressing is more effective at elevated temperatures where plastic flow causes the asperities to collapse; improved application conditions are derived from hot-work research to clarify temperature and strain rate dependence of hot strength and ductility. The substructure evolution systematically studied in hot working to determine dynamic recovery or recrystallization is applied to clarifying that developed in welding. The various processes are affected differently by work-piece geometry and final shape requirements. In addition to pre-cleaning of the surfaces, the plastic flow helps disperse the remaining oxide layers as was originally exemplified in blacksmith hot forging of layered sword blades and in bellldie welding of wrought iron tubes. The presentation critically compares the utility for various materials and configurations of simple pressure, ultrasonic application, diffusion, explosive, rotary and linear friction and friction-stir processes. Diffusion bonding (primarily Ti) with light cleaning, low pressure, little distortion in protective furnace atmosphere contrasts strongly with the heavy upsetting in friction welding, or complex alloy mingling and substructure variations in friction stir joints.

Jan 1, 2011

By N. I. Basuki, E. T. C. Spooner

"The Bongara area, northern Peru, contains Zn-Pb mineralization with characteristics typical of Mississippi Valley-type (MVT) systems. The northwest-southeast-trending late Triassic-Jurassic car¬bonate host rocks of the Pucará Group were locally replaced by early (D1) and late (D2) dolomite. Fluid inclusion microthermometric data from dolomite and sphalerite are typical of MVT ore fluids (78° to 187°C; ~15-23 wt.% CaCl2 equivalent), and do not show apparent covariation between temperature and salinity.Homogenization temperature data from D1 and D2 dolomite show a decrease from northern (mean Th = 138°C) to central (mean Th = 126°C) to southern areas (mean Th = 102°C), suggesting fluid flow from north to south. Assuming a geothermal gradient of ~30°C/km and an average surface temperature of ~20°C, the lower temperature limits might approximate the ambient host-rock temperatures, whereas the upper temperature limits may represent minimum temperatures of a deeper aquifer, probably at a maximum depth of ~6000 m. The lower temperature limits are also similar to the estimated temperatures if dolomitization and mineralization took place in the Late Cretaceous at ~2000-3000 m depth, probably during the formation of the Peruvian fold and thrust belt near the present day Peru-Ecuador border.Fluid inclusion data show that the fluids in each studied location had relatively uniform temperatures and salinities during dolomitization and mineralization. A significant salinity drop and a slight temperature decrease are observed during late calcite precipitation, suggesting mixing of brines with dilute, cooler fluids."

Jan 1, 2009

By Michel Guillot

Gaz metal arc welding is commonly used for producing large frames and assemblies. Even for light aluminum and thin wall assemblies, the GMAW technique is increasingly preferred over the GTAW technique. This is particularly true where the welding gun motion is achieved accurately with automated or robotic systems and when using pulsed or regulated metal deposition. In this study, butt joints in floor welding position are tested at speed ranging from 1.5 to 16 m/min. Attempts are made of find parameters providing good and repeatable joint quality with minimal distortion and good appearance even at high travelling speeds. Taguchi experimental plans are proposed with different parameters tested with sheet metal samples. The parameters include typical GMAW machine settings, joint preparation geometries, wire gages, gun angles, wire feeds, and more. The robot motion speed and the proximity of the part are also considered. Direct monitoring of machine welding current and voltage is achieved. Once is found the best set of parameter settings, additional tests are carried out to verify the repeatability of weld quality. Secondly, these conditions are applied for joining and testing a floor panel made of several extrusions. Weld quality is established with Vickers micro-hardness measurements, cross section geometries of the weld pool including penetration, tensile tests and metallographic observations to establish the amount of porosity and weld microstructure in the HAZ.

Jan 1, 2011

By Russell McIntosh

"The Madsen mine is in the southeastern part of Baird township, in Red Lake area, Ontario. It lies about 6 miles southwest of the town of Red Lake, with which it is connected by an all-weather road.The Madsen Red Lake Gold Mines Company was formed in March, 1935, to take over the holdings of the Falcon Gold and Jomac Gold syndicates. During 1935 an4 the early part of 1936 No. 1 shaft was sunk and drifts driven on four levels, all on a narrow quartz vein in a granite dyke.In July, 1936, the Austin zone was discovered about half a mile north of No. 1 shaft by Austin McVeigh, a prospector employed by the Company. Diamond drilling showed that the zone included an orebody worth development, and in 1937 No. 2 shaft was sunk, three levels opened up and sufficient ore outlined to justify the installation of a mill. Milling commenced in August, 1938, at the rate of 300 tons a day, which was later increased to 400 tons a day.The total production from 1938 to 1946 was 1,116,307 tons from which gold and silver having a value of $9,949,010 were recovered. The gold produced ranged from a minimum of 0.1910 oz. a ton in 1939 to a maximum of 0.2827 oz. in 1944. The average grade in 1946 was 0.2345 oz. to the ton."

Jan 1, 1954

By J. Petit

"In July 2004 workers at the ABI Smelter in Bécancour (Quebec, Canada) went on strike. Contingency plan were ready to face the situation and plan was done to operate one potline out of three. Two lines were stopped; keeping in mind the restart on cold metal after the strike was over. The subject to be presented and shared includes a summary of work organization including training, schedule of restart, pot cleaning, pot preparation, crash start method, follow up after crash start, safety and environment. This major project has been a very big challenge. It shows that people involvement is a must and the key success. It is then true to say : ""People who believe in success will work and act in order to get there"" and ""People who don't believe in success will act in such a way to fail"" Then both will prove they were right to think their own way ! Sharing such experience can be interesting because it's a true story and people like true stories."

Jan 1, 2006

By D. M. Doyle

"The Strathcona Concentrator operations, the application of control systems in the crushing, flotation and tailing fill sections, and current and future computer control concepts are described in this paper.The computer has been used for reporting and monitoring roles and operating the on-stream analyzer since start up of the mill in 1968, while over the past twenty months, it has been used for process control. The systems which have been developed include:1. The blending of pentlandite concentrate with pyrrhotite concentrate to produce a special product of constant nickel analysis.2. The blending of cement with tailing fill to produce backfill of consistent cement content.3. The supervisory control of xanthate, frother and pH to the flotation circuits to maintain the nickel copper concentrate grade within narrow limits.IntroductionThe Strathcona Concentrator is currently treating 7,200 tons per day of an ore which contains nickel associated with the minerals pentlandite (28 -32% Ni) and pyrrhotite (0.3 -1.0% Ni). The ratio of the nickel minerals varies from 4 to 15 parts of pyrrhotite to 1 part of pentlandite over the orebody. The production of a high grade concentrate re4uires the separation of this small quantity of .oentlandite from the much greater proportion of pyrrhotite and gangue and is complicated by the presence of two pyrrhotite minerals differing in nickel content, floatability and magnetic susceptibility."

Jan 1, 1974

By R. M. Bustin

"Extensive deposits of tectonically sheared coal of the Mist Mountain Formation occur in the south eastern Canadian Cordillera. The quality of the coal varies markedly; it is commonly partially oxidized and poor washability characteristics.Oxidation of the sheared coal has been promoted by its fine grain-size and by fractures in adjacent rocks which have facilitated penetration of atmospheric oxygen and circulation of oxygenated waters. Oxidation has resulted in a loss of coking power, a decrease in vitrinite reflectance, and an Increase In oxygen and decrease in carbon content.The relatively low clean coal yields of the sheared coal are primarily the result of the greater volume of mineral matter present, which in turn reflects both the greater susceptibility to shearing of coal with abundant rock partings and the shearing and dissemination throughout the coal of formerly discrete rock partings. The high ash content of some sheared coal seams may be artificial, resulting from the difficulty in distinguishing and separating sheared roof rock and floor strata from the coal seam during mining. There is little variation between the quality of the washed sheared and unsheared coal, with the exception of the somewhat higher ash content of the clean sheared coal compared to clean unsheared coal. This poorer separation of the ash from the organic fraction of the sheared coal is considered to be a product of the large amount of fines present as well as the local formation of aggregates of organic material and ash resulting from plastic flowage of the vitrite and clarite during shearing.IntroductionIn the southeastern Canadian Cordillera, coal seams of the Lower Cretaceous Mist Mountain Formation (Gibson, 1979 were in part sheared and comminuted during Late Cretaceous and Tertiary tectonism . Extensive deposits of sheared coal exist, and even in areas of mild deformation the coal may be locally sheared (Bustin, 1979). The quality of the sheared coal varies notably; it is commonly oxidized even far from the present weathering horizon, and locally has a disproportionately large amount of ash and poor washability characteristics even far from the present weathering horizon and locally has a disproportionately large amount of ash and poor washability characteristics."

Jan 1, 1982

By Ben Murphy, Tomi Maksimainen, Antti Rinne, Ishmael Muzinda, Toni Mattsson

"A 500m3 flotation cell was commissioned during 2014 at the Kevitsa Mine in northern Finland working as the first rougher in the copper flotation circuit. Treating around 850tph with an average grade of 0.3% Cu, the TankCell® e500 has run with an average copper recovery of 71% and an average enrichment ratio of 50 during early optimization test work. In addition the cell has proved to be very energy efficient, being operating with a specific energy of around 0.4kW/m3 under production conditions.A review of the installation and operation of the TankCell® e500 at Kevitsa will be presented. Metallurgical performance of the cell during the operating period will be discussed on the basis of on-line analysis and the metallurgical samples collected during early optimization campaigns.IntroductionThe past three decades have seen a rapid increase in the size of mechanical flotation cells. This has been largely driven by demand from the copper industry to process larger volumes of material due to combination of declining head grades and the desire to benefit from the economies of scale (Lynch, Harbort and Nelson 2010). During this period Outotec has been at the forefront of development of large flotation technology with an enviable scale-up track record; 100m3 (1995), 160m3 (1997), 200m3 (2002), 300m3 (2007), 500m3 (2012) to the largest commercially available cell at 630m3 in 2013. This scale-up methodology has been developed, tested and validated (Elgueta et al., 2009; Coleman & Dixon, 2010) by the large installation base of cells in the 300m3 size class operating (over 400). The learning from large cell operation are then reviewed and incorporated back into new designs and scale-up practices (Murphy, Miettinen, and Yanez, 2014)."

Jan 1, 2016

By Robert Thomson

"The Cobalt camp is by far the most productive camp of the Temiskaming silver-cobalt area. The date of discovery, 1903, is an important one in the history of Canadian mining; from then on prospecting and mining grew rapidly to take the prominent places they now hold in Canadian life.At Cobalt, prospectors and operators, who were to play prominent parts in other Canadian camps, received their initial training. The exploration campaigns leading to the discovery of several new camps were organized at Cobalt, and a considerable part, indeed, of the funds for these campaigns were profits from mining at Cobalt.The discovery of the Cobalt camp was purely accidental, not the result of any purposeful search. Fred LaRose, a blacksmith employed in the construction of the Temiskaming and Northern Ontario Railway, discovered mineral, afterwards determined to be valuable, within a few feet of the right-of-way. This discovery became part of the very productive LaRose mine. The publicity given this discovery, particularly by Willet G. Miller, later Provincial Geologist of Ontario, led to the rapid development of the camp.ProductionCobalt is a great camp by virtue of its silver production; cobalt is also important, although clearly subordinate. Copper, nickel, arsenic, and bismuth are by-products of mining for silver and cobalt and have not been of great importance to date.The following table gives the metal content of ores, concentrates, etc. from the Cobalt camp for the years 1904 to 1954 inclusive, as reported by the mines (l):"

Jan 1, 1949

By Lloyd Buckingham

"The operating cost of a gold mine employing granular activated carbon to recover gold can be greatly affected by the condition of in-circuit carbon and its attrition losses. To accurately identify and quantify carbon losses requires careful study. Carbon attrition in the mill can be attributed mainly to physical or mechanical breakage due to the transfer of carbon in the circuit and to carbon oxidation and thermal fracture occurring in the carbon reactivation kiln. Of the equipment involved in carbon transfer, the water powered eductors are the major cause of abrasion and should be replaced with pumps or alternate methods that can serve the purpose. This paper also reviews the impact of carbon stripping and washing on overall operations.IntroductionHolt-McDermott Mine operates a 1360 tonnes per day Carbon-in-Leach (CIL) mill to recover gold. The relatively high carbon consumption and high remaining gold values on carbon after stripping were viewed as a challenging project for research. Extensive metallurgical testwork was initiated to reduce these values. Figure 1 below indicates the carbon flowchart prior to any significant changes in the carbon handling procedures.Carbon consumption after commissioning which was as high as 10""/o of carbon eluted, has been brought down to less than 5%. Changes that brought about this 50% reduction in carbon consumption are:1 ) Improvements in kiln operation2) Elimination or replacement of eductors3) Reduction in tonnes of carbon eluted"

Jan 1, 1994

By George McIsaac

This paper discusses the formulation of a linear program with the objective of maximizing the cash flow of the long-term plan of an underground operation. A mine is split into eleven independent ore zones, each characterized by its reserves, required development and mining method. Based on practical considerations, maximum rates are set for each zone?s development and production capacity. As for the total mine plan, a minimum daily production rate is set along with a minimum feed grade to the mill. A maximum number of development metres per day is set based on the equipment and labour available. Proven and probable ore is mined preferentially over possible ore in the early years of the plan. Furthermore, the fixed cost of operating the mine is taken into consideration whenever mining activities take place. Once the linear program is solved, it can be critically reviewed, and unrealistic results can be identified. Some resource allocations constraints can then be changed in certain sectors, and new results can be analysed. What-if scenarios can also be examined, such as determining the impact of hiring a contractor to develop a given sector, or dropping an ore zone completely from the plan.

May 1, 2003

By Dave Marsh, John Goode, Niels Verbaan, Kevin Bradley, Henrie Notzl

The mineralogy of the Avalon Nechalacho deposit is complex with significant fractions of HREEs, Zr, and Nb found in refractory minerals such as zircon and fergusonite. Sulphuric acid baking followed by water leaching can be used to extract REEs from flotation concentrates, but acid baking does not completely "crack" the zircon and fergusonite, so the extractions of Zr, Nb, and HREEs are not high. An alternative flowsheet has been developed that is able to obtain significantly improved extractions of HREEs, Zr, and Nb from flotation concentrates or acid bake residues. This is accomplished by cracking the zircon and fergusonite minerals with caustic soda at high temperatures, followed by water washing to recover excess caustic soda and soluble sodium silicates and phosphates. REEs, Zr, and Nb in the solid residue can then be solubilized with HCl or H2SO4. This paper highlights some of the findings from an extensive laboratory program and discusses several flowsheet implications.

Jan 1, 2014

By F. G. Smith

Abstract Laboratory methods are now in use whereby the temperature and pressure during the crystallization of hydrothermal minerals can be determined. The techniques include the use of the decrepitation method of studying liquid inclusions, and electrical measurements of pyrite. The determinations are sufficiently accurate that the data can be used in solving a variety of ore deposition problems. Within the last year, several new laboratory techniques have been developed in the Geochemical Laboratory of the Department of Geological Sciences, University of Toronto. The results of several tests of ore by these methods have proved to be useful in treating some problems which previously were considered unsolvable. It is now possible to determine the temperature of deposition of most of the minerals in a hydrothermal ore deposit, also the depth below the surface during deposition. Measurements can also be made of the reopening history of a complex ore. The temperature-pressure determinations depend upon the fact that minerals deposited from a hydrothermal solution always trap a small amount of the solution at the time of crystallization. The solution, being predominantly composed of water, has a density which depends upon the temperature and the pressure prevailing during crystallization. After ore deposition is complete, erosion and isostatic uplift finally exhumes the vein. During this slow fall in temperature and pressure, the solution contracts and a gas bubble appears. If the trapped solution in the mineral is examined, the gas-liquid ratio records the density of the solution at the time the mineral was deposited (except for a slight change in the volume of the mineral). The thermal expansion and compressibility of water and water solutions are known to a sufficient degree that, if the gas /liquid ratio can be determined, the temperature-pressure relations during deposition can be calculated.

Jan 1, 1949

By D. Imeson, T. Grammatikopoulos, M. Aghamirian, M. Oliazadeh

"More than 70% of potash is produced worldwide by froth flotation. Flotation of potash was developed in the early 1930s. Amines are widely used for flotation of sylvite (KCl) from halite (NaCl) and insoluble materials such as clays. Amine collector is also absorbed by clays. Therefore, clays are usually separated by scrubbing and de-sliming prior to flotation. Alternatively, slimes can be floated ahead of potash flotation. Flotation recoveries of sylvite are commonly in the range of 85%, while losses can occur in slimes, flotation tailings and make-up of process brine. Ores containing free coarse-grained sylvite are generally screened, whereas both fine and coarse fractions are conditioned and floated separately. The unique features of potash flotation include solubility of sylvite in water, the size of particles floated and fast kinetics. Particles up to 2.3 mm can be floated and about 50% of flotation feed can be removed in the rougher stage in few minutes. The main challenges in potash flotation are the recovery of potash from slimes, flotation efficiency in the presence of carnallite and recovery of coarse potash grains. A review of potash flotation shows that there is still room for improvement in both coarse and fine potash flotation. The present paper reviews the most significant flotation parameters including reagent type and dosage, flotation circuits, flotation equipment size and new developments in potash flotation. The latter include new reagents, flotation technologies (Hydrofloat, Jameson and column cells) larger flotation cells and slimes flotation.INTRODUCTION Potash is the common industrial term for potassium in various chemical combinations and minerals soluble in water. About 90% of potash produced worldwide is used as agricultural fertilizers. Flotation is the main treatment process of sylvinite (KCl-NaCl) ores for recovery of sylvite (KCl). Potash concentrate should contain a minimum of 95% KCl and be relatively free from 0.2 mm KCl fines. The flotation process for beneficiation of potash ores was developed in United States and Russia concurrently in the early 1930s. In 1934, Potash Corporation of America applied flotation process in a commercial scale (Tippin R.B. and Huiatt J.L). In the initial application, halite (NaCl) was selectively floated by employing lead chloride as an activator and soap as collector. The sylvite concentrate was reported in the cell underflow."

Jan 1, 2012