Search Documents

By M-A. Thibault, C. Gauthierand, J-P. Gagné, J-Y. Carrier, P. Rochette, G. Dufour

"Anodes consumed in the electrolytic process for the production of primary aluminium are considered consumables. They need to be replaced at regular intervals of approximately one month. The so-called anode butts which are removed from the cells contain the metal supports (rods), cast iron thimbles, crust and residual carbon material. Cleaning is required to remove the waste material before the rods are fitted with new anodes. An inspection is required to ascertain if repairs to the rods are necessary. Presently, this inspection is carried out visually. ST AS, in 2004 in collaboration with Alcoa Deschambault, initiated a project to develop an automated inspection system. The objectives were to find a technical solution to perform these functions with a very simple system. Such a system was designed around ""artificial vision"". The inspection system developed uses only one fixed camera and does not require a separate step in the process for the anode rod assembly to perform the inspection. This paper presents the initial steps of the work performed to develop the equipment and software as well as a summary of the results obtained."

Jan 1, 2006

By Kurt F. Weitz

"The number of materials that can be classified as fillers covers an extremely wide range: this paper outlines those fillers of the industrial mineral type that find extensive application in the paint and plastics industriesIn the paint industry, mineral fillers are known as extender pigments. Extenders are added to paint and plastic compositions to (1) lower the cost and (2) rein-force or modify the physical properties of a composition.Commonly used extenders are classified according to chemical type and discussed in terms of the change in physical properties that they impart to a paint or plastic film. Available cost reductions and data on the consumption of extenders in the Canadian paint industry are also included."

Jan 1, 1970

By Brian Hart, Zhe Chen, Liuyin Xia, Mana Pourdasht, Stamen Dimov

"Gold losses related to carbonaceous matter (CM) during processing are a significant problem in the gold processing industry. Inherent CM in gold ores can behave similarly to activated carbon in its ability to adsorb gold cyanide. This phenomenon is termed preg-robbing as the surface adsorbed gold cannot, for the most part, be recovered. Research has identified that gold adsorption by inherent CM is linked to the specific surface area, pore structure, degree of C disorder and surface functional groups. One of the strategies to inhibit CM preg-robbing prior to leaching is a chemical oxidation; a process linked to modification of the surface functionality. In this study, the variability in gold cyanide adsorption due to oxidation with different reagents has been investigated. Variability in gold cyanide adsorption by CM is examined in relation to structural and surface modifications using TOF-SIMS, XPS and Raman spectroscopy.INTRODUCTION A major obstacle for effective gold recovery during carbon in leach (CIL) or carbon in pulp (CIP) processes carbonaceous gold ores is the presence of carbonaceous matter (c-matter) which has the ability to adsorb, or preg-rob gold from the cyanide leach solution. It can be responsible for poor recoveries as the carbonaceous materials (CMs) within the ore competes with activated carbon used during the leaching and adsorption phase of processing (Cay, 2014). Preg-robbing capacity can vary significantly with mild preg-robbing ores showing absorption capacities of less than 1 g Au/t ore, while severe preg-robbing ores may have CM with the capacity to preg-rob more than 500 g Au/t ore (Dunne, 2007). Research by a number of groups have shown that the degree of C disorder has some influence on the ability of the carbonaceous material to adsorb Au(CN)2- (Miller et al, 2005, Helm et al, 2009, Hart et al, 2010). It is also apparent the adsorption characteristics of carbonaceous material is affected by changes in surface chemistry (Dimov, 2016). Various treatment including; flotation to remove the carbonaceous material (Wills, 2010), addition of surface blinding agents (for example kerosene) to passivate or blanket the carbon surfaces (Dimov, 2016), addition of strong adsorbents (eg. activated carbon or resin) to compete with the carbonaceous material and passivation or surface coating by oxidation (pressure, roasting, chlorination and biological oxidation), have been employed prior to leaching in an attempt to minimize the gold losses (Dunne, 2013)."

Jan 1, 2017

By T. Hidayat

The distributions of minor elements between slag/metal and slag/matte in equilibrium with tridymite in the Cu-Fe-O-S-Si-Al-Ca system have been investigated in the range of conditions of interest to the high- temperature copper production, refining, and recycling processes. An improved experimental methodology has been used involving high temperature equilibration in controlled gas atmospheres, rapid quenching, and quantitative microanalysis techniques using Electron Probe X-ray Microanalysis (EPMA) and Laser Ablation Inductively Coupled Plasma Mass Spectrum (LAICPMS). The effect of oxygen partial pressure on the distributions of minor elements between slag/metal and slag/matte has been accurately measured. The effects of slagging components (Al2O3 and CaO) on the distributions of minor elements between slag/metal have also been experimentally determined. The present study is a part of a larger integrated experimental and thermodynamic modelling research program in the systems relevant to high-temperature copper processing. INTRODUCTION In the high temperature processing of copper, minor elements are distributed between different phases, i.e. liquid slag, liquid matte, and liquid metal. From a processing perspective, it is desired to have the valuable minor elements distribute predominantly in the metal and matte phases rather than in the slag phase, and to have the non-valuable minor elements distribute predominantly in the slag phase rather than in the metal and matte phases. Knowledge of the distributions of minor elements between phases in the smelting, converting, and refining processes is required if the distributions of minor elements between phases in these processes are to be optimized.

Jan 1, 2019

By K. D. Watson

"THE Mindamar zinc-lead-copper mine, owned by Mindamar Metals Corporation Limited, is at Stirling in Richmond County, near the south-eastern shore of Cape Breton Island, Nova Scotia (Figure I). It is connected by several roads with the Canadian National railway at Sydney and St. Peters.The deposit is said to have been discovered around 1895 as an outcrop in the bed of Copper brook, but the details are obscure. Not until 1925, when it was optioned by American Cyanamid Company, was it developed underground. Between 1927 and 1938, the 1-nine was operated intermittently by The British Metal Corporation (Canada) Limited, and yielded approximately 200,000 tons of ore averaging about IO per cent zinc, 2 per cent lead, I per cent copper, and small quantities of silver and gold. In December 1950, Dome Exploration (Canada) Limited made an agreement with Mindamar Metaî Corporation Limited, which was exploring the old mine, to assume management and prepare the property for production. Production started in April 1952 with a new mill and a new four-compartment shaft, and between that time and the end of 1954 it has totalled 545,347 tons of ore averaging 5·89 per cent zinc, 1·35 per cent lead, 0·66 per cent copper, 0·032 oz. gold, and 2 151 oz. silver.The Mindamar orebodies are irregular lenses and large veins lying within a wide, almost vertical shear zone of remarkable persistency. The shear zone consists mainly of well-foliated sericite schist derived from siliceous siltstone, and it contains a vast amount of dolomite and magne-site of hydrothermal origin. Most of the ore is extremely fine-grained and some of the high-grade material has a conspicuous thinly layered structure. The metallic minerals, in order of decreasing abundance, are pyrite, sphalerite, chalcopyrite, galena, and tennantite; the gangue minerals, in the same order, are dolomite and magnesite, quartz, sericite, talc, chlorite, barite, albite, and alunite.The geological setting of the deposit is shown in Figure 2. Except along streams and lake shores, almost all of the bedrock is concealed by glacial drift. The group of rocks in which the deposit occurs consists principally of greywacke, siltstone, tuff, brecoia, and Javas, and has been correlated lithologically with the Bourinot group of Middle Cambrian age. A short distance west of the mine, these rocks are in contact along the Stirling fault with conglomerate, arkosic sandstone, and quartzite belonging to the Middle River group of Silurian or Devonian (?) age, which elsewhere in the area overlies the Bourinot group unconformably. The large bodies of granitic rocks in the region, and the large lenticular masses of diorite and quartz diorite associated with them, have been assigned by Weeks (5, pp. 68-69) to the Devonian."

Jan 1, 1949

By K. C. Grogan

"GeneralGIANT ORE is complex, with the gold values for the most part occurring in extremely close association with arsenopyrite, stibnite, jamesonite, and a wide group of antimonial minerals locally termed 'the grey minerals'. Pyrite is the most abundant of the sulphide minerals• and minor quantities of chalcopyrite, galena, and sphalerite also occur. Pyrrhotite has been found in some sections of the mine, but to date none of it has been nickeliferous. Native gold occurs in varying amounts throughout the ore bodies.In 1944, ore dressing investigations were commenced on diamond-drill core rejects and samples of surface outcrop ore. Results soon indicated that treatment to produce satisfactory recovery of the gold values would involve fine grinding to 80-85 per cent minus 200 mesh, recovery of free gold by jigs, followed by flotation, roasting of the flotation concentrate, and subsequent cyanidation of the calcine. Proceeding from this information, the flow-sheet was prepared, plant design worked out, equipment purchased, and construction of the treatment plant commenced in May, 1947.The crushing, grinding, and flotation units of the plant were rushed to completion and commenced operation on May 12th, l.948, at 225 tons of ore per day. This rate was maintained until January 27th, 1949, when the Allis-Chalmers roaster and cyanide plants were completed and commenced operation. During the period May 12th, 1948, to January 27th, 1949, gold recovered by amalgamation was the sole source of revenue. Flotation concentrate was stockpiled pending the completion of the Allis~Chalmers roaster and cyanide plants."

Jan 1, 1953

By J. P. Messervey

As a result of my field examinations in this Province, I have been struck by the evidence of widespread mineralization in rocks, particularly the limestones of Carboniferous age. Six prospects of lead and zinc or lead alone scattered through the eastern part of the mainland, one copper prospect and three veins of siderite, all point to a period of mineralization subsequent to the forming of the Carboniferous rocks in which they occur. While none of the present prospects are of proved economic importance, still it is possible, and indeed probable, that further prospecting will find concentrations sufficiently large to make mines. It may possibly aid the prospecting for these base metals if the present scraps of information are assembled from various sources, and I will further briefly recount the information as a result of my observations. Gay?s River At Gay's river, midway between Halifax and Truro, and four miles east of the railway, numerous pits and natural exposures show galena and sphalerite in limestone of Carboniferous age, near where it lies unconformably upon slate and quartzite of the gold series. These exposures extend for a length of over one thousand feet along a curving contact. The pits show that on the contact there is a fossiliferous and somewhat porous layer of limestone, which is so impregnated with galena and small amounts of sphalerite as to be of ore grade. Wherever observed, the thickness of this layer is less than two feet.

Jan 1, 1929

By Keith Haddock

"The Sheerness Mine, a new surface coal mine located near Hanna, Alberta, went into full production in mid-1995. The mine, which is operated by Luscar’s subsidiary Forestburg Collieries (1984) Ltd., has the design capacity to supply up to 2.1 million tonnes of sub-bituminous coal per year to the adjacent Sheerness Generating station under a 30-year contract. This paper documents the construction phase of this project and highlights the major equipment purchases as well as the construction of the mine facilities. The paper also focuses on some of the areas where cost savings have been achieved that have allowed the mine to come on stream six months ahead of schedule, and under budget. Project ReviewMine DescriptionThe Sheerness Mine is located 25 km southeast of the town of Hanna in southeastern Alberta (Fig. 1). The mining property occupies the western portion of the Sheerness CoalField and borders the Montgomery Mine, operated by Manalta Coal Ltd. in the east, and Highway 36 in the west. The Montgomery Mine and the Sheerness Mine exclusively supply the total coal requirement of the adjacent Sheerness Generating Station. The station is owned jointly by Alberta Power Limited (APL) and TransAlta Utilities Corporation (TAU). APL is the operator. Manalta’s Montgomery Mine has supplied coal to the Sheerness Station since its opening in 1986. Coal is shipped by truck from the mines over a network of haul roads to the coal receiving hoppers located on the east side of Highway 36."

Jan 1, 1997

By N. Bakhshizadeh

In this investigation, the aging effect on creep behavior of A12024-10%SiC composite fabricated by powder metallurgy was studied. P/M bars were manufactured by hot powder extrusion method at 450°C with a ratio of 16 to 1. Creep specimens were over-aged at 187 ºC for 43 h. It was found that almost full density composite with relatively homogenous distribution of reinforcing particles throughout the aluminum alloy matrix could be attained by direct powder extrusion process. Creep tests were conducted at temperatures from 275 to 325°C under stresses from 25 to 60 MPa. The analysis of the creep mechanism determined that dislocation glide was the predominant mechanism of plastic deformation. The activation energy of the creep process was found to be higher than that of lattice self-diffusion in pure aluminum.

Jan 1, 2007

By M. J. Bennett

"The Quemont mill is primarily a differential flotation plant in which copper, zinc ·and pyrite concentrates are recovered. Native gold and silver are associated in the form of very small particles with all the minerals contained in the ore: chalcopyrite, sphalerite, pyrite, pyrrhotite and even with the gangue rock.The proportion of the precious metals associated with chalcopyrite is such that the best recoveries we can obtain in our copper flotation concentrate are about 68 percent of the gold and 51 percent of the silver in the ore. In order to improve the total recoveries of precious metals it is necessary for us to float a pyrite concentrate and treat it by cyanidation for the extraction of whatever gold and silver we can obtain in this manner. In spite of the fact that we regrind this concentrate to 75 percent minus 325 mesh, it is difficult to extract much more than half of the gold and silver present in the pyrite concentrate by cyanidation, due to the extremely fine association of the precious metals with the pyrite.In 1963 we produced 86, 853 ounces of gold by flotation alone, and 14, 581 ounces by cyanidation. These amounts are equivalent to 67. 74 percent and 11. 37 percent respectively of the total gold in the mill heads. Comparable figures for silver are 325, 598 ounces by flotation and 99, 448 ounces by cyanidation; and 51.37 percent and 15.69 percent respectively.The total annual value of these metals (ie. $4, 000, 000) qualifies Quemont as a precious metal producer of some note. On the other hand, it is evident that by far the greater proportion of our gold and silver production is contained in copper flotation concentrates. When the income from our copper and zinc values is also considered, the much greater importance of flotation compared with cyanidation in our operation may be appreciated. This explains why most of our work on controls has been carried out in our flotation mill, rather than in our cyanide plant. Some of the controls installed there could, of course, be employed in either type of operation."

Jan 1, 1964

By Hongfei Li, JianLong Wang

This paper introduces the technical characteristics, transformation scheme and production practice of the project in which Copper P-S Converter was replaced by Bottom Blowing Continuous converting for the first time, and introduces the technical achievements obtained by the project. The application practice proves that bottom blowing copper continuous converting technology can completely solve the problems of fugitive off-gas pollution in the ladle transportation, large amount of flue gas and fluctuation of flue gas caused by P-S converting. Comprehensive energy consumption and operating costs of producing blister copper, safety and environmental risks are greatly reduced, and economic, environmental and social benefits are significant. It is one of the preferred technologies for upgrade and to replace P-S converting technology. INTRODUCTION At present, more than 80% of copper production capacity is still using the P-S converting technology with a history of more than 100 years. During P-S converting process, melted copper matte needs to be transported by ladle, and it needs to rotate the furnace body several times, causing a lot of serious environmental and safety risks such as SO2 flue gas emission and low-altitude SO2 pollution. In addition, the high operating cost caused by low rate of air blowing, the short life of the refractory materials and high energy consumption during P-S converting become big problems. Other problems such as large amount of flue gas, low SO2 concentration, large fluctuation of flue gas volume and SO2 concentration, and discontinuous flue gas cause high cost of subsequent flue gas treatment are also needing to be solved. In order to solve these problems during the P-S converting, metallurgical engineer in various countries has spared a lot of efforts to develop continuous blowing process for decades. The continuous converting that have been industrially applied are flash continuous converting, Mitsubishi continuous converting, Noranda continuous converting, Bottom Blowing Continuous converting and multi-lance top blowing continuous converting

Jan 1, 2019

By John D. Godfrey

A brief account of economic developments in and around northeastern Alberta is presented and mention is made of mining and industrial developments currently of interest in the area. Planned and projected operations are briefly discussed for this region. The history of geological surveys and mining activities in the Shield area of Alberta and the adjoining parts of Northwest Territories and Saskatchewan is traced. Reassessment of the presently-known economic picture of northwestern Canada in conjunction with some recent information on Precambrian structures of northeastern Alberta points to some interesting mining possibilities, particularly in and around that province.

Jan 1, 1960

By Claudia Gasparrini

"Silver occurs in about 200 minerals in variable amount s. Silver ores usually have 5 or 6 and in some instances as many as 10 species of silver minerals. All these minerals may have different flotation and leaching properties and should be correctly identified for successful recoveries. Grain size and host minerals which are critical in gold recovery, are not always as important for silver minerals.IntroductionMineralogical factors affecting the metallurgy of silver are , as for other metals: (i) the silver-bearing mineral s ; (ii) their grain size, and when dealing with very fine sizes; (iii) their host minerals; and (iv) the association they form with the silver-bearing minerals. Of these, the silver-bearing minerals are more often the cause of problems during recovery as opposed to gold whose metallurgy is generally more affected by grain size and host minerals. The problems derive mainly from the complexity of the silver mineralogy: over 200 minerals exist bearing the element in major, minor and variable amounts.As a member of group I-B of the periodic table, silver forms extensive so lid solutions with the other two elements in the same group , copper and gold. It combines with sulphur, tellurium and selenium in covalent bonds and with chlorine, bromine and iodine in ionic bonds. Where the fluid composition, temperature and pressure during crystallization allow it, silver also combines with arsenic, antimony, lead, bismuth, tin, mercury, indium, thallium, and germanium in many instances as a minor element in sulphide , sulphosalt and native element minerals. Cations which silver replaces to a lesser extent than copper and gold are iron, manganese, zinc and probably nickel and cobalt."

Jan 1, 1984

By H. Pempel, J. Markowski, P. Ay

"Metal-coated thermoplastic parts find more and more functional and aesthetic applications in the interior and exterior of cars. The vapor-deposited or electroplated coatings are usually composed of a plurality of nickel- and chromium-containing layers, which are applied to copper-containing carrier layers on the polymers. Previously, recycling processes are mainly focussed at the recovery or thermal utilization of the plastics. Targeted and selective recycling of the metallic coatings is usually not carried out. Together with several SME, BTU developed a process, in which a complete and separate recovery of all components in high purity is possible with biotechnological methods. The bioleaching is carried out with iron and sulfur-oxidizing bacteria, especially Acidithiobacillus ferrooxidans. The copper-containing layers are dissolved in the solution; chromium- and nickel-containing particles are precipitated as solids. After the bioleaching, a mechanical separation of the individual metal-containing components and their separate workup are carried out. End-products are metallic copper, a nickel- and chromium-containing solid and the cleaned plastics. The bioleaching ensures a high purity of the end products. Through the use of bacteria, which are also found in nature, the process is environmentally friendly. Compared to chemical leaching using inorganic acids, considerably shorter leaching times can be achieved. In addition to the optimization of the leaching process, the R/D-project also includes the development and testing of the apparatus technology.INTRODUCTION The material complexity of many end-user products has increased in recent years, especially in the fields of electrical appliances, vehicle technology and medical technology. However, the demands on functionality, safety, comfort and energy efficiency still play a greater role in product design as factors such as sustainability and usability. For example, if a car still holds more than 70% of steel in the 1980s, a vehicle nowadays includes a larger proportion of a variety of difficultly separable plastics and composite materials, as well as complex metal composites. This relates in particular to composites made from such different materials as metals and plastics. The processing and recovery of the components of those complex material mixtures is difficult for recycling companies."

Jan 1, 2017

By David A. Grieve, David E. Pearson

"A rank-map of Crowsnest coalfield, showing the distribution of the bituminous coal measures and the locations of major structures, has been produced from vitrinite reflectance measurements on over600coal samples. The timing of coalification in relation to these major structures has also been determined.In the west-central portion of the coalfield a complete stratigraphic succession of coal measures which rides on major thrust surf aces is all of high-volatile bituminous rank, but despite the structural discordance no break in rank is discernible across these structures. The thrust faults therefore predate much of the coalification.Three major valleys expose cross sections of the folded coal measures and in each an increase invitrinite reflectance is demonstrable as individual seams are traced from ridge crest to valley floor. Thus, in these sections, a significant amount of coalification post-dates folding. The proportion of this post-folding coalification is found to increase toward the south of the coalfield.A late gravity-fault, exposed along the east crop of the coalfield, places high-volatile coal-bearing successions in contact with low-volatile coal and demonstrably is a reactivated thrust fault. Coalification at this locality occurred between these two different ages of faulting.The variations in rank and the subtleties of the coalification pattern have, together with systematic changes in the maceral composition of coal seams, had a profound effect on coal quality in the coalfield. Coking coals with a variety of properties occur together with some coals that have no caking capacity."

Jan 1, 1985

By Brigitte J. Dejou

The Red Dog sediment-hosted zinc-lead deposit is located in the Brooks Range thrust belt in northwest Alaska, approximately 1000 km northwest of Anchorage. The mine constitutes the primary deposit in a 400 square kilometre district, which hosts several other mineral occurrences. All the known mineralisation is hosted by the Mississippian Ikalukrok Member, deep basinal shale of the Kuna Formation, part of a Devonian to Cretaceous sedimentary sequence. The rocks underwent intense deformation during the Brookian Orogeny in Middle Cretaceous time. Several thrust faults juxtapose the stratigraphy. The Red Dog mine is composed of four deposits which together contain 105 Mt in resources and reserves for a total resource exceeding 18 Mt of Zn metal. The mine is an open pit with 25 foot high benches. The biggest challenge is not the Arctic conditions, but metal extraction, due to the fine grained nature of the mineralisation and the variability of the ore. The mine produces Zn and Pb-Ag concentrates that are shipped to smelters around the world from the Red Dog port facilities during the short summer period. Ore mineralogy is generally simple and consists of sphalerite, pyrite, galena and marcasite. The deposits are generally overlain by decametre thick exhalative barite horizons and exhibit strong silicification, which locally obliterates the original textures. Although described as a world class Sedex-type deposit, a large portion of the mineralisation exhibits sub-surface replacement textures. Moreover, unlike most other Sedex deposits, the reconstruction of the basin is made difficult by the structural complexity of the district. To assist exploration in the district, several assumptions are made regarding the deposit settings relative to metal source, growth faults or crustal extension.

May 1, 2006

By C. Taschereau, G. A. Vickell, A. R. Laplante

Evidence in support of an iron-gold corrosion cell during the high-temperature/highpressure elution of loaded carbon is presented herein including, but not limited to, its discovery, mode of genesis, and confirmatory laboratory testwork. A discussion of metallurgical and economic impacts, remedial investigations, plant design considerations, and future work including mitigative possibilities is presented.

Jan 1, 2006

By R. Amelunxen

"The molybdenite associated with copper porphyry ores is generally treated in a flotation circuit consisting of a separation and a cleaning section. In the last few years column flotation cells have replaced the numerous counter-current stages that were previously used in the cleaning section. Despite this, little has been published regarding the number of column cleaning stages required. Therefore a Moly flotation database is assembled with the objective of verifying the existence of a common upgrading profile. This can then be used as a guide in the prediction of the number of stages required to achieve a given concentrate grade.INTRODUCTIONAlthough the first use of Column Flotation was on copper flotation products, the popularity and understanding of their operation was not really achieved until they were widely implemented in Moly circuits in early 1983. The use of columns in Moly plants has since left a legacy of information, both published and unpublished. The data collected since that time has been used primarily used to establish column operating parameters and to determine upgrading potential within the circuit.Byproduct Moly generally occurs with porphyritic copper ores in concentrations less than 0.1% MoS2. As such, piloting a new moly ore to produce, say 5 Kg/Hr MoS2, in a slurry approximately 1 Lt/min (at 10% solids), requires a moly plant feed of about 570 Kg/Hr, which translates to a mill feed rate of 200 to 800 Tonnes per day (depending whether you deal with Chilean or Canadian ores). Piloting Moly for any lower tonnage would reduce the accuracy of the testwork.Thus a need exists to collect operating data in order to establish the existence of process relationships that could be used for feasibility and design purposes.The object of this paper is to expose a preliminary relationship that could be used for the purposes described above and to apply the findings to a preliminary design of a moly cleaning circuit flowsheet."

Jan 1, 1990

By Paul G. Dunn

Safe rapid drift development results principally in reducing exposure of underground workers to the working face. This reduction in exposure is not achieved until either the rock walls have been suitably scaled or sufficient support has been put in place. Rapid drifting enables quicker access to orebodies (increasing returns), higher production rates and a resultant lower cost of mining. The Mining Innovation, Rehabilitation And Applied Research Corporation (MIRARCO) has been developing technology and a methodology for safe rapid drift development within the underground metalliferous mining industry. In terms of rock scaling for underground metal mines, there is still considerable use of manual and mechanical impact rock scaling techniques. Two main issues result from this approach. The first is that in highly stressed or highly fractured ground, a decision has to be made as to when sufficient scaling has taken place. This is not always easy to do and hence operator judgment is a crucial element in this approach. During a baseline study of current rock scaling practices, a wide range of scaling practices were observed within five different underground mining operations; this demonstrates the difficulty inherent in the rock scaling quality decision making process. The second issue is related to the exposure of workers to freshly created rock surfaces. In manual scaling techniques this is unavoidable and despite the best scaling practices, accidents still occur. In an attempt to provide an alternative scaling technology, MIRARCO has been investigating highpressure water jet scaling for removing loose rock as part of the drift advance process. This technology not only provides a means by which scaling practices can be engineered (remove the loose material you want to in a given rock mass condition), it is also quicker and easily automated. Automating the scaling process removes workers from exposure to freshly created rock surfaces and also enhances the application of spray-on liners through improved adhesion of these support types to the rock surface. This paper describes the water jet scaling technology research and methodology for safe rapid drifting within the underground metaliferous mining industry and highlights the key issues and major drivers behind their continued development at MIRARCO.

May 1, 2004

By Dale Lens, W. S. (Wayne) Cusitar

"The use of continuous loading and conveying technology for mining is currently practiced in relatively few mining environments and, even in these cases, on a non-exclusive basis. For the most part, and particularly in hard rock mining, appropriate equipment technology has only recently been developed for continuous loaders, mobile low profile crushers and flexible face conveyors. Mining R&D work by Inco Limited has promoted the development and proving of a loader suited to hard rock conditions and capable of sustained loading rates of500 tonnes per hour. Current R&D work at Inco will test the production capabilities of a low profile mobile crusher by CMS/Eagle and a flexible/ mobile face conveyor system by DME. This follows successful production testing of the Belt Bender concepts in potash mining in Saskatchewan and the development of enhanced extensible conveyor equipment features by DME. Numerous applications are seen for variations of the LCC technology in soft rock, hard rock and surface mining environments. Introduction In some respects, this paper is an announcement of new technology which has the potential to bring revolutionary change to the mining industry. It is also the story of technology transfer, in which mining concepts that have developed independently in underground soft rock and hard rock mines and in surface mining operations are being brought together for a common benefit. It is also the story of key developments in equipment technology which 'complete the cycle' of cooperating technical capabilities to enable the revolution to begin. The phrase ""technological revolution"" requires some defmition: an equipment innovation, or invention, or improvement, will only be revolutionary if its use gives rise to a significant new mining practice."

Jan 1, 1987