Search Documents

By B. Dubé, R. Friedman, J. Oliver, R. Aubertin, M. Burson, G. Panneton, M. Hamilton, J. Ayer

"The Detour Lake gold deposit is located within the northwestern limit of the Archean Abitibi Subprovince of the Superior Province. Mineralized zones are hosted by a sequence of pillowed and massive flows, hyaloclastite units, and altered ultramafic rocks, and are commonly oriented parallel to a series of high-strain zones that are co-planar to the regional-scale Sunday Lake Deformation Zone. Early in its kinematic history, the Sunday Lake Deformation Zone placed older (2.72 Ga) volcanic rocks of the Detour Lake Formation over younger (2.70 Ga) sedimentary rocks of the Caopatina assemblage. Gold mineralization is also parallel to the position of a laterally persistent siliceous rock unit, the 2.725 Ga ‘Chert Marker Horizon.’ The Chert Marker Horizon coincides with the boundary between the mafic-dominated upper Detour Lake Formation and the ultramafic-dominated lower Detour Lake Formation. Stratigraphic and geochronological data suggest that the Chert Marker Horizon is a deformed felsic volcaniclastic unit. At a cut-off of 0.6 g/t Au, the Detour Lake deposit contains 17.26 million ounces of Au within 445.9 million tonnes of rock grading 1.20 g/t Au. Gold occurs in shear-hosted and extensional vein arrays within rocks of the upper and lower Detour Lake Formation and within the Chert Marker Horizon. The Detour Lake deposit has many of the characteristics of a greenstone-hosted, quartz-carbonate vein deposit; its very large size may be attributed to large-scale rheological controls resulting in the formation of dilatant sites in permissive rock units."

Jan 1, 2012

By P. A. Riveros

This paper describes the leaching of the common copper minerals tennantite (Cu12As4S13), tetrahedrite (Cu12Sb4S13) and enargite (Cu3AsS4) in acidic media using Fe(SO4)1.5, FeC13 or 02 as oxidizing agents. At temperatures <100°C, tennantite dissolves slowly in Fe(SO4)1.5-H2SO4 media, and the rate is directly proportional to the area of the sized tennantite. The rate increases sharply with increasing temperature and the apparent activation energy is 69 kJ/mol. Increasing Fe(SO4)1.5 concentrations slightly increase the tennantite leaching rate. The kinetics of dissolution of disks of synthetic iron-bearing tetrahedrite in Fe(SO4)1.5-H2SO4 media are linear; the leaching rates are slow but increase significantly with increasing temperature, with an apparent activation energy of 120 kJ/mol. The dissolution of sized particles of natural Ag-bearing tetrahedrite in FeC13- HC1 solutions proceeds according to the shrinking core model, and both Cu and Ag dissolve at about the same rate, provided that the total chloride concentration of the solution is sufficiently high to solubilize the AgC1 reaction product. The leaching rates are slow, and the apparent activation energy is 116 kJ/mol. The addition of sulphate ions to the FeC13-HC1 system reduces the tetrahedrite leaching rate to values similar to those realized in the Fe(SO4)1.5-H2SO4 system. At <100°C, enargite dissolves slowly in either Fe(SO4)1.5 or FeC13 media, and the dissolution rate obeys the shrinking core model. The rate increases with increasing temperature and the apparent activation energies are 50-64 kJ/mol. The rate increases slightly with increasing FeC13 concentrations in 0.3 M HC1 media. The leaching of enargite at elevated temperatures and pressures was also investigated. Potentially useful leaching rates are achieved above 170°C, at which temperature sulphate, rather than sulphur, is produced. Lower temperatures (130-160°C) lead to fast initial leaching rates, but the dissolution of the enargite is incomplete because of the coating of the enargite particles by elemental sulphur.

Jan 1, 2007

By H. Lee

Recently, the effects of global climate changes have become top concerns for governments? decision making regarding infrastructure investments. Extreme weather events that exceed the capacity of existing systems have considerably increased in frequency, and the potential effects of changing trends in temperature and rainfall on infrastructure are difficult to ignore. It is essential for governments to estimate the costs and benefits of adaptation to climate change to properly assess the financial feasibility of infrastructure adaptation strategies. This paper proposes a framework for estimating the economic aspects of infrastructure adaptation to climate change. The framework is composed of three steps of implementation: establishment of alternatives for infrastructure adaptation, performance prediction of infrastructure using future climate scenarios, and asset valuation based on costs and benefits. The first step specifies target assets, their adaptability to climate change, and applicable adaptation technologies. The second step evaluates the effects of climate change on the performance of infrastructure. The last step determines the optimal adaptation strategies among various alternatives based on their net benefits. The framework reasonably incorporates future climate scenarios into the estimation processes for climate change effects and provides a basis for budget allocation for governmental infrastructure investments. The framework is expected to assist government decision makers in establishing adaptation strategies in a rational manner under uncertain future climate change.

Aug 1, 2013

By I. Lackey

In 2004, Zinifex Budel Zink commenced testing with the objective to increase the precipitation of aluminium in the iron purification stage of its hydrometallurgical zinc circuit, without the use of expensive reagents. Findings from the literature applied to the leach circuit at Zinifex Budel Zink demonstrated that aluminium removal from the leach circuit could be increased by lowering the ferric concentration and acidity in the vessels where jarosite precipitation occurs. An associated increase in copper precipitation was mitigated by limiting the extent to which the ferric concentration was lowered in the vessels where jarosite forms and lowering the ratio of copper to aluminium in the solutions entering these vessels.

Jan 1, 2006

By I. C. Brown

Introduction Many tables of nomenclature for igneous rocks have been introduced from time to time, and each has its strong proponents. As a result, any discussion of igneous? rocks is apt to prove confusing unless the names used for these rocks are defined. This ?became so obvious to a discussion group, formed by the members of the Geological Survey of Canada in 1948, that an attempt was made to establish a scheme of nomenclature that could be used by any member mapping anywhere in Canada. The writer was asked to co-ordinate the ideas presented by individuals in the discussion group, to arrange them in tabular form, and, later, to distribute copies of the resultant table to Canadian universities, provincial geological surveys, and some other geological discussion groups. Many useful suggestions and criticisms were received, were studied ?by members? of the original group, and, so far as practicable, were incorporated in the scheme of nomenclature. The result is the table presented here. This nomenclature of igneous rocks is at present being used by most members of the Geological Survey of Canada who are working with igneous rocks, and by some Canadian universities. We hope it will be found useful and be more widely accepted. With this idea in mind, certain principles were adopted in drawing up the nomenclature.

Jan 1, 1952

By William C. Boggis

EKATI? Diamond mine is located 300km northwest of Yellowknife and 200 km south of the Arctic Circle in the Northwest Territories of Canada. The site is a remote tundra area with continuous permafrost and is in the Canadian Shield. EKATI? is the first diamond mine in Canada and is operated by BHP Diamonds Inc., which is a part of BHP Minerals. BHP Diamonds Inc. is an incorporated company based in Vancouver, BC. The mine is a joint venture of BHP Diamonds Inc. (51%), Dia Met Minerals Ltd. (29%), Charles E. Fipke (10%) and Dr. Stewart L. Blusson (10%). The mining area lies within the 10,960 ha land leases held by the joint venture. The total claim block covers 344,000 ha. To date over 136 kimberlite structures have been identified within the claim. Five of these provide the basis for the present mine plan with three others identified for future inclusion. At full capacity the mine will produce 4.5 million carats per year, approximately 4 % of world production and employ approximately 600 people, with over 33% being Aboriginal from the Northwest Territories.

May 1, 2001

By Lutz Markworth, Fernando Parra, Wolfram Jaspers

"The worldwide demand of iron ore and the depletion of the high-purity deposits make it necessary to recover ores in increasingly fine size fractions or low Fe content in the feed material. Impurities for Iron ore processing plants are mainly Silica, Al2O3 and Sulfides.There is a copper processing plant in Chile, which has a high content of Fe in its tailings. These tailings will be re-processed to recover the Fe and to produce a pellet feed concentrate. This challenging flotation process was developed by the customer in his own laboratory. Different flotation technologies were tested. The best results were achieved with the PNEUFLOT® (PNEUmatic FLOTation). For a feed capacity of approximately 600 t/h, a flow sheet of two flotation lines with a reverse two-stage Amine-Silica flotation followed by a single stage reverse Xanthate Pyrite flotation was developed.Because of the two impurities the process control is very critical. Not even the reagent dosing has to be flexible for changes in the feed material; also the flotation cell has to be adaptable. Continuous development of the PNEUFLOT® cell with their specific advantages and the elimination of dysfunctions in the PNEUFLOT® cell have led to a growing demand of this type of equipment worldwide for the iron ore industry within the past years.INTRODUCTIONThe worldwide increasing demand of iron ore is mainly caused by China. This has a major impact on all economics worldwide as the metal price indicates. However, not even the iron ore and steel price, but all other commodities prices and the precious metals prices are increasing by a high percentage. Figure 1 shows the iron ore (pellets) price increase for Fe and the import of iron ore by China. Figure 2 shows the imports of iron ore to China."

Jan 1, 2008

By Kadir Sariiz

Abstract - The Akçayir-Yürükakçayir Miocene-Pliocene basin in the Central Anatolia hosts ancient lacustrine sepiolite deposits. The succession in this basin consists of conglomerate (Yürükakçayir conglomerate), clayey and silty limestone, dolomitic marl, sepiolite beds and lenses, and dolomitic limestone (Kepeztepe formation). The main impurities within the sepiolite rock are dolomite, opal-CT, calcite, smectite and feldspar as sepiolite + dolomite and sepiolite + opal-CT are the main mineral assemblages. Smectite and feldspar are thought to be of detrital origin. Calcite is found as a secondary filling in root tubes and casts. Sepiolite samples studied display root-marks and root tubes, soapy and massive structure indicating direct precipitation. Sepiolite deposits probably formed at a pH of 8 to 9, and Mg+2 and SiO2 concentrations in moderately saline environments of internal facies of an alkaline lake.

Jan 1, 2000

By F. Charette

Instrumentation has been developed that can monitor the strain applied to a D-Bolt up to 7.5% elongation. The technology far exceeds the limit for foil resistance strain gauges. In the laboratory the instrumentation has provided insight into the fundamental behaviour of the D-Bolt following yield. Currently the instrumentation is undergoing field trials at a number of Canadian Mines. Discussion on field results is provided with regards to significance, reliability and temperature effects.

Aug 1, 2013

A study was made to determine the effect of increasing concentrations of dissolved oxygen on the floatability of galena pyrite and chalcopyrite. Adsorption, flotation and contact-angle tests were done in deoxygenated, in air-saturated and in oxygen-saturated solutions. The results showed that the adsorption of collector increased as the concentration of oxygen increased. Adsorption followed the exponential law r = kC'/"• Discontinuities in the curves were observed after the adsorption of several monolayers of collector. Although adsorption increased with increasing oxygen concentration, the floatability of the pyrite minerals did not increase, because oxidation had adverse effects on the floatability of these minerals. The floatability of galena was maximum in oxygen-saturated solutions, pyrite was depressed and chalcopyrite was also slightly depressed. Contact-angle tests proved that a bubble could not be attached to large flat surfaces in deoxygenated solutions, because sufficient surface free energy was not available for adhesion after the deformation of the bubble. In the presene of air, all the minerals yielded the same maximum angle of 72 degrees, characteristic of isopropyl xanthate.

Jan 1, 1970

By Nordau R. Goodman

T-he Ojibway Salt Mine near Windsor, Ontario, produces almost two million tonnes of97% pure rock salt annually. The salt is mined from the middle F horizon of the Silurian Salina Formation. The salt beds have a gentle dip into the Michigan depositional basin. There is no evidence of deformation. The rock salt is buff coloured and has a number of thin carbonateanhydrire bands. Secondary salt crysrallization occurs throughout the mine.

Jan 1, 1984

By A. Hynes, T. Skulski, D. Francis

The Archean volcano-sedimentary succession in the LG-3 area has undergone two phases of deformation and has been metamorphosed to upper greenschist and amphibolite facies. Marine, fine-grained sediments and mafic pyroclastics comprise the lowest observed stratigraphic unit. These sediments are overlain by a thick sequence of submarine basalts and minor basaltic andesite. The lavas are characterized by high Al/Al+Si, Ti values, low Mg numbers and flat REE profiles (lOx chondrite). A sedimentary prism of coarse elastics which was deposited close to an exposed plutonic highland, overlie the volcanics. Massive lavas of basaltic andesi te and associated volcano-sediments comprise the uppermost stratigraphic unit. These lavas are characterized by high Mg numbers, Ni, Cr, LREE (lOOx chondrite) but low Ti, Al/Al+Si and HRee. The supracrustal rocks were intruded by tonalites and tonalitic gneisses.

Jan 1, 1984

By R. A. Payant, J. A. Finch

Under certain conditions of air and moisture, sulphide materials can spontaneously heat, or selfheat. The reaction mechanisms of self-heating are not well understood. Most previous work has involved pyrrhotite because it is the most reactive sulphide. The current work investigates the self-heating behavior of sulphide mixtures composed of sulphides other than pyrrhotite. The four studied sulphides were pyrite, chalcopyrite, sphalerite and galena. The rest-potential was measured for each. Binary mixtures formed as a 1 : 1 weight ratio were pyrite-galena, chalcopyrite-galena, pyrite-chalcopyrite and chalcopyrite-pyrite. The four sulphides and the binary mixtures were subjected to standard self-heating tests. The four individual sulphides did not self-heat. However, mixtures of pyrite-galena and chalcopyrite-galena with rest-potential difference (?E) >0.3 volts did self-heat while the mixtures of pyrite-chalcopyrite and chalcopyritesphalerite with rest-potential differences (?E) = 0.1 volts did not self-heat. The results demonstrate that when certain non self-heating sulphides are combined they can self-heat. A possible explanation based on galvanic interaction and formation of hydrogen sulphide as an intermediate product is discussed.

Jan 1, 2009

By William Skinner, Jim Pae Lem, Massimiano Zanin

It is well known that the specific density of minerals has adverse influence on the classification performance of a hydrocyclone, particularly when liberated high density minerals such as gold or uranium are present in sulphide ores. These liberated heavy minerals often misreport to the underflow and recirculate to the system. Such phenomena does result in serious issues in a closed-grinding circuit, such as overgrinding, leading to production of flaky particles (as in gold) or ultrafines, in addition to increased energy inefficiency. In plants which present gold liberated at coarser size, loss of gold due to cyclone inefficiency is sometimes prevented by incorporating gravity concentrators into the grinding circuit to recover the gold. The work reported in this paper looks at whether the effect of density will prevent successful rejection of liberated U-bearing minerals in the –10µm size range of a plant re-cleaner feed, which is necessary to minimize penalty U accumulation in a copper concentrator. The study was carried out using a cyclone rig with spigot diameter of 0.25 inches in combination with batch flotation. It was found that the density effect is almost negligible at particle sizes below 10µm. Consequently, the liberated U-bearing particles finer than 10 µm were successfully removed in the overflow stream as rejects and hence U grade in the copper concentrate remarkably reduced, by 16 ppm. Based on the results, de-sliming of the re-cleaner feed was recommended for plant trial and implementation.

Jan 1, 2016

By B. Leonard

As of November 2012, the Alberta government listed 53 oil and gas, oil sands, and mining construction projects either proposed or currently under construction. These industrial plant construction projects have an estimated value greater than 105 million dollars. A common construction method employed for industrial plant projects is fast-track construction, which is used to reduce construction time. Contractors begin fast-track construction with highly generic scheduling information. This high level schedule turns into a lower level schedule as more detailed information becomes available. From a contractor?s perspective, a challenge faced using fast-track construction is the visualization of generic and constantly changing project schedules. This paper discusses the use of a Plant Information Modeling (PIM) system, designed to create a 4D animation to visualize project schedules for fast-track industrial plant construction projects. The proposed PIM system creates a modified project schedule by obtaining specific information from a generic construction schedule. Obtaining the information involves grouping schedule activities in accordance with the level of detail in a 3D model, and the level of detail in a project schedule. The modified project schedule is then used in conjunction with a 3D model to simulate the construction sequence in the form of a 4D animation. This allows for 4D visualization of project activities, installation dates, and crane movements. Furthermore, as engineering reaches completion, the PIM system creates a streamlined channel for schedule information updates to be easily uploaded into the model for a more accurate 4D visualization. Through analyzing a nonmodular construction case study, this paper discusses the successes and benefits of the PIM system for 4D visualization, such as increased productivity, shortened construction time, increased constructability, and decreased field costs.

Aug 1, 2013

By Muhammad Tawalbeh

The calculated temperature history of a single particle of MgCl2 hydrates when it came in contact with fused salt electrolyte at 650 °C was determined using the measured heat transfer coefficient for the molten salt bath at 650 °C. The calculations revealed that the entire interior of the particle reached the temperature required for the formation of MgOHCI from hydrated MgCl2 in less than 2 seconds. This was much less than the time required for dissolution of the prills as observed in experiments. It is very likely that the formation of MgOHCI during prill dehydration and dissolution is a result of hydrolysis in the interior of the prills.

Jan 1, 2004

By R. Neumann, O. Gomes, S. Gaydardzhiev

"Phosphorus in iron ores is considered as a deleterious component to iron making reflecting in cold shortness of the produced steel. The present study investigates the phosphorus migration pattern resulting from thermal treatment of an oolitic-type iron concentrate with and without additives. To this end focused mineralogical and microscopic observations were performed. The results have shown that roasting with alkaline additive drives phosphorus outside the hematite hosting mineral, however it remains evenly distributed inside the volume of the oolites. It penetrates inside the newly formed cementing phases of Al- Na-Si-Fe-type and also fills the interstices between the crystals. Other than phosphorus, aluminum, calcium and iron tend also to migrate towards the amorphous-type cementing phase. Finally, the possibilities for P removal by means of magnetic separation and acid leaching of the roasted concentrate were evaluated. The obtained final product presents a standard iron concentrate suitable for steelmaking with its phosphorous being dropped from 0.71% to 0.05% and iron grade of a nearly 66% being reached. INTRODUCTIONSignificant proven reserves of iron ores are still not exploitable due to lack of an economically viable and efficient technology for removal of phosphorus. Among them are the oolitic iron ores with high phosphorus which are estimated to nearly 377 billion tons (Hernandez et al., 2012). Phosphorus is a deleterious component giving a cold shortness to steel and often is penalized if exceeding 0.07%. Most of the high-P iron ores are considered refractory since phosphorus is finely disseminated and is evenly met as phosphate groups inclusions inside the limonite structure. Studies on inclusion of phosphorus in artificially synthesized goethite have shown that it is adsorbed as [HPO4]2- groups bridging the adjacent iron ions (Parfit et al., 1975). The high-phos iron ore originating from Lisakovsk deposit, Kazakhstan presents a similar mineralogical issue because the quantity of P, met as solid solution, is substantially higher than the one in P-containing minerals. A potential reason for that is the ore body formation process from the slow deposition of iron-rich precipitates together with clastic erosional sediments in rivers. There is significant quartz and clays inside and around the oolites. The deposit contains about 1.7 billion tons of measured and indicated reserves at 35–41% iron and 1.1 billion tons of inferred ore have been delineated possessing nearly the same chemical composition (Golubovskaya, 2003; Kokal et al., 2003)."

Jan 1, 2016

By S. A. Vazhnov, A. G. Kalimov, A. A. Potienko

In this paper we describe a mathematical model of the magnetic field and magnetohydrodynamic processes simulation in aluminum reduction cells developed in St. Petersburg State Polytechnic University, Russia. The model includes: (a) calculation of the currents in the busbar system and inside the aluminum cell construction elements including cathode and anode structures, aluminum and electrolyte layers; (b) magnetic field simulation using the integral equation method; ( c) investigation of the magnetohydrodynamic characteristics on the basis of a shallow-water approach. The developed model was used to investigate operational characteristics of the different industrial aluminum cells. Calculated magnetic field distributions and MHD stability parameters were compared with the available experimental information; the comparison demonstrated a reasonably good agreement.

Jan 1, 2006

By Gerhard Melcher, Hermann Hilbrans, Michael Gamroth

"IntroductionSeveral new smelting processes have been proposed and developed during the last 20 years. This has been true, in particular, for copper smelting technology. The important impulses for the advances in this field have been the recent demands regarding the environmental protection, energy saving and improved utilization of the metals contents of deposits, in particular that of complex raw materials.The methods developed more recently for pursuing these objectives have been outlined in several papers. In some of them the advantages and drawbacks of certain developments have been stressed. These documents are of great importance for assessing the different processes. The following paper tries to explain some details of the cyclone smelting process taking into consideration a few of these well-known presentations. The effectiveness of operation of the cyclone smelting process indicates that this process presents a significant achievement when compared with other conventional methods.The application of the CONTOP smelting cyclone range s beyond the field of copper metallurgy or the smelting of sulphide concentrates with the aid of oxygen. The research work carried out in the pilot plant of KHD Humboldt Wedag AG in Cologne-Porz also includes the recovery of the metal contents of intermediate products and processing of smelter residues which have to be converted in a disposable stat e, free of environmental pollution. This paper explains a few examples in this regard."

Jan 1, 1987

By X. Gu

Mining operations, especially surface coal mines, have great impacts on the local ecosystem and the environment. However, it has been a common practice in mine design that the economic evaluation considers only the operating and capital costs, while the costs incurred due to ecological damage are left out. Such practice underestimates the total cost of mining and ignores the difference in ecological impacts between different mine design alternatives. With growing interest in sustainable development, the mining industry is under increasing pressure to operate not only based on economic and engineering principles but also on principles of sustainability. Therefore, estimating ecological costs of mining and considering such costs in the mine design process is an important step towards reducing ecological impacts at the design stage. The objective of this paper is to quantify the ecological costs of open pit coal mining and to demonstrate the influence of such costs on the ultimate pit design. The ecological costs of mining are estimated based on the areas and types of land damaged by mining activities and the carbon emission from energy consumption. Four major components of ecological cost are identified, namely, lost value of direct eco-services, lost value of indirect eco-services, prevention and restoration costs, and the cost of carbon emission from energy consumption. Necessary equations are given for estimating these costs. An algorithm is described for ultimate pit optimization in coal deposits with near-horizontal coal seams. A case study is presented in which the ultimate pits with and without ecological costs are optimized and compared to show the influence of ecological costs on the pit design outcome.

Aug 1, 2013