Search Documents

By Jean-Francois Magnan

"The old conventional process to produce lithium raw material dates from 1954 (CA patent #504477A). This process produces low purity lithium carbonate (Li2CO3) only. To obtain battery-grade carbonate, another polishing process is needed. To further obtain lithium hydroxide, another chemical conversion process is needed. That is why historically, the value of lithium hydroxide has always been higher than that of the lithium carbonate precursor. With the old conventional process, the low quality lithium carbonate is precipitated from a lithium sulfate solution (Li2SO4) by adding soda ash (sodium carbonate and its impurities). The resulting reaction produces significant quantities of sodium sulfate (salt cake) as a by-product with amounts larger than the impure Li2CO3 recovered with part of the soda impurities. When this conventional process was invented, the salt cake by-product was not an issue: it was discarded in a river near the plant. This practice cannot be done today in North America. While looking to find a solution for salt cake, electrolytic salt splitting of Na2SO4 into NaOH and dilute sulfuric acid appears as a technically feasible solution to get a rid of the salt cake. However, the sodium sulfate salt splitting process has difficulties to economically compete with the chlor-alkali process, which produces millions of tons of NaOH from sodium chloride (NaCl) every year.In contrast, the process developed by Nemaska to directly produce LiOH by Li2SO4 salt splitting not only solves the environmental problems related to the conventional process to produce lithium carbonate raw material, it also produces very high purity lithium hydroxide monohydrate directly at very competitive OPEX cost in comparison with industry peers (Figure 1). It also drastically reduces the amount of reagent and the direct greenhouse gas emissions."

Jan 1, 2016

By M. Cimenti

Fuel cells have tremendous potential as power sources but much fundamental research is still required. One key component of the research is the experimental set-up used. In particular, the placement of the reference electrode is extremely significant in measuring the half-cell overpotential of solid oxide fuel cells, since differences in area, misalignments, and also differences in the kinetics of the working and counter electrodes can cause both scaling errors and frequency distortions of the measured impedance. The impedance of thin solid electrolyte cells of different electrode geometries has been calculated using the finite element method and the results compared to experimental values obtained for the oxygen reduction reaction on platinum.

Jan 1, 2005

By H. Blaha, H. Wagner

"Room and pillar workings in salt mines are preferred sites for underground waste disposal. A critical issue in selecting waste disposal sites is long-term behaviour of such workings. The long-term behaviour of salt pillars is controlled by the pillar geometry, i.e. the height, width and length of pillars and the level of pillar stress. The latter has a strong influence on creep characteristics of salt pillars whereas the width to height ratio of salt pillars determines the strength of pillars and the deformation characteristics of salt pillars.Three different regimes of pillar creep behaviour of salt pillars can be distinguished, namely a stress level below which the rate of creep approaches a value of zero, a stress range where the rate of creep is constant and finally a stress level above which the rate of creep accelerates. Long-term stability of room and pillar workings can be assured only when the pillar stress level falls within the first stress regime. Strength and creep tests on model salt pillars have shown that at stress levels below 40% of pillar strength the rate of creep approaches a value of zero, between stress levels of 40% and 65% the rate of creep is constant but increases with stress level. Above pillar stress levels of 65% the rate of creep accelerates.Long-term measurements of pillar deformation and surface subsidence above relatively shallow room and pillar workings in salt mines have confirmed these observations. Long-term strength of salt was found that be between 60% and 65% of short term strength. The evaluation of salt pillar behaviour on the basis of critical pillar stress levels was found to be superior to the traditional factor of safety concept because it allows relating pillar deformation measurements to actual pillar conditions. The approach described in the paper was used successfully to evaluate the stability of room and pillar workings in a salt mine and to design strategies to stabilise critical pillar workings."

Jan 1, 2015

By Richard F. Lynch, Frank E. Goodwin

"The development of Galfan, a new generation 95% zinc-5% aluminum-mischmetal alloy coating for steel, offers opportunities for greater fabrication flexibility and upgraded corrosion performance in automotive applications. The formability of Galfan is equivalent to that of electrogalvanized steel, based on laboratory tests and automotive component fabrication. Corrosion resistance of Galfan exceeds that of hot dip and electrogalvanized, including performance in automotive industry tests. Automotive production applications for deep drawn and stamped components in France and Germany are based on the ability to meet dual performance requirements for upgraded formability and corrosion resistance. The first U.S. Galfan application was on 1985 model Ford cars and light trucks for transmission oil cooler lines which has now expanded into a number of power steering tubing uses. IntroductionContinuing requirements for improved vehicle performance coupled with the ever present need for reduced cost have spawned the development of a number of new coated steel products. Among this new generation of coated steels is Gaifan™, a 95070 zinc-Solo aluminum-mischmetal hot dip alloy coating. Galfan exhibits particular promise for automotive use based on broad fabrication advantages and upgraded product performance(I ),The unique characteristic of Galfan is the key combination of greatly improved formability with much longer corrosion life. Galfan provides significantly better formability than any other hot dip coating. Testing shows that formability is limited primarily by the steel substrate to which the Galfan coating is applied. Galfan exhibits excellent resistance to flaking and microcracking during commercial forming operations. The result is the elimination of unnoticed damage to the coating which would show up later as premature rusting on the finished product."

Jan 1, 1987

By F. Urekar, R. B. Pankhurst

"Air spaces and air gaps in an explosives column are known to allow greater distribution and cushioning of explosive energy from the rock mass. This energy distribution is enhanced if the explosives ' gases can be confined in the borehole for as long as possible by plugging and stemming above the air space.Power Plug is an inflatable plug which can seal a borehole at any point to separate the stemming from an air gap and explosive toe load.IntroductionThis paper will discussion-going work by C-I -L Inc. and operators of two open pit mines to study the results of using Power Plugs:I. Pit wall stability - the authors have found the Power Plug effective for wall control blasting in open pit mines.2. Selective mining of coal seams - the authors work shows the Power Plug allows mining selective coal seams by predrilling underseam waste wedges.Pit Wall StabilityWall stability in an open pit mine is essential for safety. Good wall stability can be achieved with wall control blasting techniques which cushion the effect s of the explosives charge by decoupling the charges from the borehole wall. The usual method of decoupling a charge in a large-diameter rotary borehole is to load the explosives in tubes (Fig .I) . We now believe the air deck system is effective in sea ling a borehole above the explosive charge to create an air deck within the borehole which will cushion the blast.In a linear decoupled charge, an air annulus surrounds the explosives charge and cushions the effects of detonation genera ted gases on the pit wall. In an air deck, i.e. with the hole plugged at the collar, the gases genera ted by an explosive toe load are sealed in the empty borehole column. After a period of time, these trapped gases produce radial cracking between holes along the entire length of the borehole.It is common practice to employ de coupled explosive charge columns in the borehole to limit blast damage to surrounding rock. The exact mechanism of energy transfer in such blasts, however, is not well understood. Interruption of the continuous explosive column in a borehole by means of stemming, or air decks, may also be viewed as another form of decoupled blast. Decoupling of the explosive charge from the borehole wall affects both explosive energy release and explosion pressure developed in the borehole."

Jan 1, 1988

By T. Yeomans

NVI Mining’s Myra Falls operation is a forty-year-old underground mining operation feeding a 4,000 metric tonnes per day concentrator. The current mill, built in 1985, was designed to process a massive sulphide ore-body. This orebody, known as the HW, contains about 50% pyrite. Minerals of value are chalcopyrite and sphalerite, with precious metals occurring in all mineral types. By 1997, mining of a new ore-body, known as Battle-Gap, commenced. Mineralogically complex, the new orebody contains about 15% pyrite copper minerals, including primary chalcopyrite and secondary bornite, chalcocite and tennantite, combined with increased galena and sphalerite. Flotation performance generally decreased with increasing amounts of Battle-Gap ore types, with both copper concentrate quality (increased lead and zinc content) and copper recoveries being affected. Following significant metallurgical test-work, a new, fully sequential copper-lead-zinc flotation flow sheet and reagent scheme was developed. This sequential flow sheet was progressively installed and commissioned during 2006. Copper concentrate lead and zinc smelter penalty contents have been reduced by some 40%, while increasing copper recovery by 10%.

Jan 1, 2009

By T. Haubold, K. Ortner, T. Jung, D. Roth-Fagaraseanu, C. Mattern

Application of integrally bladed disks (blisks) is of increasing interest in compressors of aero engines. Blisks are preferred due to their potential for size and weight reduction, for increased performance and for reduced manufacturing costs compared to conventionally bladed disks. Erosion of the blisk aerofoils in service reduces engine performance, and can result in short shop visit cycles. This significantly increases the life cycle cost of these components, particular when considering that eroded aerofoils can't be exchanged easily for blisks during refurbishment. Shop visit cycle times can be extended and maintenance costs can be reduced through the application of an effective protective coating. The ongoing development of an erosion resistant coating and deposition process suitable for coating complex blisk geometries is described here. The coating is a multilayered W /TiB2 system exhibiting superior erosion resistance compared to known single- and other multilayer concepts. A modified sputter process is used to enable coating even of blisk geometries with shadowed surface to competitive recurring cost.

Jan 1, 2006

By William Petruk

Mineralogical investigations in connection with gold metallurgy are usually performed to find the reason for poor recoveries by cyanidation or by other leaching techniques. Poor recoveries most commonly are obtained when (I) native gold is encapsulated in an insoluble mineral as "invisible gold"; (2) native gold is coated with a precipitate; (3) gold-bearing products are insoluble in cyanide solutions; (4) carbonaceous material in the ore adsorbs gold; and (5) associated minerals decompose and consume cyanide. Samples of refractory material quite often have low gold tenors. It is difficult to find the gold-bearing minerals in such samples with an optical microscope because the probability of finding trace minerals in samples is small. The probability decreases with decreasing grain size of the gold-bearing mineral and with decreas¬ing gold tenor of the sample. Techniques have been developed to increase the success rate of finding gold grains; some are (1) concentrating heavy minerals; (2) preparing special polished sections; (3) searching with an image analyzer; and (4) dissolving associate silicate and sulphide minerals.

Jan 1, 1989

By Jean-François Lapointe

Many advances have been made concerning the automation of heavy equipment teleoperators such as those found in mining. Complete automation, however, is not achieved yet and the operation of these vehicles still relies on the presence of a human operator. Fortunately, a lot of research has been done in order to improve the performance of these human-machine systems. This paper presents the characteristics of different control modes and input devices used for the control interface of those telemanipulators. We describe the benefits and drawbacks of each particular control interface on the overall system performance, based on a review of research in the field. We conclude with some recommendations and a discussion of future research needs, given the new potential advances offered by virtual environment technology and embedded computing.

May 1, 2001

By Ralph Harris, Javier Jara

"Oxygen is essential in gold cyanidation. It is supplied to the leaching media by sparging oxygen or compressed air into the cyanidation tank. The rate of oxygen transfer is critical to achieve the desired oxygen concentration in solution.The performance of a novel device for gas sparging recently developed at McGill University is compared to the mass transfer characteristics of the two spargers most used in the gold industry: the four lance configuration and the inverted cone. The distribution of gas and the kinetics of oxygen desorption of the three types of spargers was studied in a 140 litre tank. The oxygen dissolution of the new device is three to five times faster than the other spargers. This could increase the leaching rate and/or decrease the cyanide and oxygen consumption.IntroductionIn hydrometallurgical processing, it is often necessary to bubble gas through a pulp to carry out the wanted reactions. The gas can act to agitate the pulp and it can also supply reactant. The rates of the reactions which require a reactant supplied by the gas are often dependent on the rates of mass transfer from the gas to the solution.A common example of this is gold cyanidation which requires oxygen for gold dissolution. Since the gold containing slurry is rich in other oxygen consuming substances (sulphide like pyrrhotite), it is important to provide enough oxygen to allow complete gold dissolution within the residence time of the cyanidation reactors. It has been demonstrated that the rate of gold dissolution is directly proportional to the dissolved oxygen concentration of the pulp which in turn is proportional to the oxygen partial pressure in the bubble 1 2 3. Improving the rate of mass transfer of oxygen increases the dissolved oxygen concentration of the slurry and therefore improves the rate of the reaction.The rate of mass transfer from a bubble to its surrounding solution increases with decreasing bubble size and increasing gas bubble residence time which in turn increases with decreasing bubble size. The generation and dispersion of small bubbles is thus critical to achieving high rates of mass transfer. Different configurations and devices used to inject gas have different effects on the bubble size and the residence time, influencing the overall rate of mass transfer. Therefore better mass transfer can be achieved by adopting a more efficient method.The methods tested in this report are the four lance configuration (wall spargers), the inverted cone and a new device, designated HCD. The wall spargers and the inverted cone are used widely in the industry today."

Jan 1, 1994

By Adrianus (Adrian) Halim, Tomas Bolsöy, Stina Klemo

"This paper describes the ventilation system used in underground hard rock mines in Sweden and Finland, which is very different than the system used in other major mining countries such as Australia, Canada, South Africa, and USA. The system utilizes auxiliary fans with Variable Speed Drive to distribute primary airflow to working levels instead of regulators that are commonly used in other countries. Descriptions about Ventilation on Demand in this system and ventilation regulations in Sweden and Finland are presented in this paper. This paper also quantifies a comparison between the Nordic and the system used in other countries. KEYWORDS Auxiliary fan, Regulation, Ventilation on demand (VOD), Variable speed drive (VSD) INTRODUCTION The primary objective of an underground mine ventilation system is to provide sufficient airflow to dilute atmospheric contaminants that are produced by mining activities. Typically, a mine ventilation system consists of one to four primary fans, regulators to control primary airflow distribution to levels or panels, and auxiliary fans that distribute airflow to dead-end workings via ducts. Depending on circuit geometry, underground booster fans are sometimes used. This system is widely employed in many countries such as Australia, Canada, USA, United Kingdom, and South Africa. However, mines in Nordic countries such as in Sweden and Finland employ a different system, in which auxiliary fans instead of regulators are used to control primary airflow distribution, as well as distributing airflow to dead-end workings. This paper describes the general layout of Nordic ventilation system, its VOD and heating system, its comparison with the system that is widely used in other countries which is referred as “Non-Nordic ventilation system” in this paper, and the current ventilation regulations in Sweden and Finland. The comparison was quantified by doing simulations using Ventsim Design 5 software. DESCRIPTION OF NORDIC VENTILATION SYSTEM General System Layout Figure 1 shows a schematic of typical ventilation system used in Swedish and Finnish mines. The schematic was drawn by Franzen, Myran, Larsson, and Rustan from Stiftelsen bergteknik forskning (Swedish Rock Engineering Research Foundation) and the English translation is written next to the Swedish terminologies. The system is generally a push-pull system. None of Swedish and Finnish mines use exhaust system. As shown in Figure 1, the primary airflow is distributed to levels by auxiliary fans that are bolted to a bulkhead located in the access to intake raise/shaft. These intake fans are attached to ventilation ducts that distribute airflow to all working faces. The exhaust auxiliary fans, which are not attached to any ducts and also are bolted to a bulkhead located in the access to exhaust raise/shaft, then flow the exhaust airflow into the exhaust shaft. A small quantity of this exhaust air is directed into the ramp, which acts as another main exhaust airway. The deepest level is also equipped with booster fan(s) that draw air from the intake shaft/raise and direct it into the ramp to provide fresh air in the ramp. There is no free split in this system. Figure 2 shows a schematic of a level ventilation layout in the Nordic system. Figure 3 shows a photo of these auxiliary fans."

Jan 1, 2019

By R. G. Zaripova, N. D. Ryan, H. J. McQueen

The austenitic and ferritic stainless steels do not undergo any phase transformation that induces very fine grains in the product through thermomechanical processing as practiced in most other steels. Considerable grain refinement can be achieved by intense multistage deformation descending through warm to cold working; notably multi-axial forging of bulk material can attain high strains with diminished risk of cracking. Hot working to improve ductility yields finer grain sizes as the T is reduced and strain rate E raised; increased strain has limited effect due to the steady state regime. Ferritic steels develop subgrains with size diminishing as E rises and T falls with the advantage of retained strain hardening; recrystallization delivers grains several times the cell size. In austenitic steels, dynamic recrystallization (DRX) provides finer grains at higher E and lower T with a lower limit due to intergranular cracking. The DRX grains contain a strengthening substructure that can easily be retained by quenching; if static recrystallization is allowed to occur the grain size rises markedly. Multistage rolling with diminishing T is able to provide grain refinement to the same degree as straining at the finishing T yet provides better ductility. grains on recrystallization. As a result of the strain induced transformation to martensite, small subzero deformations of austenitic or duplex steels produce very high dislocation densities that yield marked grain refinement when they revert upon reheating.

Jan 1, 2004

"Some of the tools developed for the processing of nickel laterite ore by resin-in-pulp (RIP) may be applicable to the remediation of metalliferous mine drainage (MMD). In both cases, recovery of metal value and production of a stable waste stream appropriate for long term storage is desired. MMD typically has the additional challenge of management of toxic low-value metals. Seen in this light, innovations in RIP reactor configuration, selective elution strategies and novel synthetic ion exchange resins become useful tools for taking on the MMD challenge in a way that maximizes both environmental and economic benefit. INTRODUCTIONAcid mine drainage (AMD) is a common problem in any country with significant past mining activity. When sulphide containing minerals, tailings or slag are exposed to water, oxygen and sulphur oxidizing bacteria, AMD will result. Abundant and reactive iron sulphide minerals leach first, providing acidity and the ferrous/ferric couple that can enhance the oxidation kinetics of other minerals. If this runoff contacts encounters acid consuming carbonates or silicates, the acidity may be neutralized, but certain heavy metals remain in solution and can continue to be an environmental hazard (Gray, 1997). For this reason, the remainder of this paper will refer to the broader term metalliferous mine drainage (MMD) rather than acid mine drainage. In either case, such drainage, containing high heavy metal concentrations and often significant acidity, is toxic to aquatic life and can lead to significant damage to ecosystems and to public watercourses. MMD is a problem most commonly associated with now defunct sulphide mineral mines, but similarly toxic streams can result from many types of waste, such as poorly stabilized leach tailings, slag heaps, and coal flotation tailings (Johnson and Hallberg, 2005; Lee et al., 2002; Sainz et al., 2002; Schüring et al., 1997). In any case, the management and remediation of MMD is an important ongoing problem for the resource industry, particularly for the many mines in Canada closed before the advent of more stringent environmental standards. MMD remediation represents a significant long term expense for the resource industry. Multi-disciplinary efforts to understand and mitigate this problem range from creation of artificial wetlands (Poulin and Lawrence, 1996; Sheoran and Sheoran, 2006) to sophisticated biochemical reactors and precipitation processes (Hatami, 2010). Certain remediation technologies such as ion exchange offer methods to make a saleable product by recovering valuable dissolved metals. This paper will show how these technologies can help defray the cost of remediation, and offer potential to turn a dangerous waste stream into a useful product."

Jan 1, 2012

By M. Kataoka, Y. Obara

It is known that compressive strength and tensile strength of rocks vary significantly with specimen size. Rocks are composed of crystals and grains in a fabric that includes flaws such as microcracks, grain boundaries and pores. As the likelihood of including severer flaws becomes greater for a larger specimen, the strengths are small. On the other hand, the size effect in the fracture toughness of rocks has not been made clear until now because there are few studies focused on it. In this paper, Semi- Circular Bend (SCB) test was performed using Kimachi sandstone with various specimen sizes. A shape of the specimen is a semi-circular disc with an artificial notch. The specimens were prepared with various thickness t and radius r as the following two groups; t was changed from 10 to 37.5 mm with r = 37.5 mm in the specimen of group (a), and r was changed from 12.5 to 150 mm with t/r = 0.8 in the specimen of group (b). As a result, there was no significant change in the fracture toughness with different t. On the other hand, the fracture toughness increased with increasing r and converged on a certain constant value in a range larger than approximately 70 mm of r. Consequently it was clear that the size effect in the fracture toughness of the sandstone exists.

Jan 1, 2015

By Fernand Dubuc

"The New Pascalis property is situated in Louvicourt and Pascalis townships, about 200 km east of Val d'Or, Quebec. It is made up of 38 claims under option to SOQUEM since August I, 1981 during which time SOQUEM has earned a 60% interest. The property is underlain by archean basaltic volcanics that have been intruded along the west boundary by the Bourlamaque batholith, and by north -trending dykes.The 1982 disco very is related to the re-evaluation of a 1931-gold showing located in the southeastern part of the property, a combination of the presence of a weak IP anomaly at the eastern end of the showing and overburden stripping at that location, resulted in the discovery of a mineralized diorite dyke.The dyke, which strikes N 20 ° Wand dips vertically , has intruded E-W striking agglomerates. The dyke contains south dipping, gold-hearing quart z-tourmaline-pyrite veins that are distributed in a ladder-type arrangement. Visible gold may he observed in drill core, and is generally associated with pyrite porphyroblasts.Diamond drilling has outlined th e dyke for a strike length of 300 11/ and a width of about 10 m, Result s of this drilling indicate, to a depth of 155 m, reserves of 834 000 metric tonnes grading 8.25 g Au/t un cut or 5.38 g Au/t cut to on e ounce. However, four deeper holes have added depth extension to 400m. Also, west of the dyke and within 150 m, other promising gold values have been intersected within quartz-tourmaline veins associated with other parallel dykes."

Jan 1, 1985

By E. Esponosa-Gomez, J. A. Finch, A. R. Laplante

"Water quality plays an important role in oxide flotation. The effects on selective flotation of fine (1-16 um) pyrochlore of two types of water used at the Niobec concentrator, potable and plant recycle, were assessed. Several pyrochlore collectors and silicate depressants were tested. Water effects were different for each mineral-reagents) combination. In general plant recycle water decreased selectivity and increased reagent consumption. Interpretation of results is given in terms of electrokinetic effects, hydrolysis of cations, and mineral-collector interactions. Two techniques of treatment for plant recycle water, cation precipitation and zeolite adsorption were assessed. The former was found to be more effective under the tested conditions but recycle water continued to give poorer selectivity than the potable.INTRODUCTIONWater quality plays an important role in selective flotation. Specific effects have been reported by many workers (1-6) and in general the better the water quality the more selective is flotation. Water composition depends on origin and the minerals being processed. For example pulp containing salt-type minerals (calcite, apatite, dolomite) will contain more Ca and Mg cations than that from a sulphide deposit. Another source of water contamination is the flotation reagents added to the pulp, particularly if water recycling is practiced."

Jan 1, 1986

By K. P. Plucknett, Z. Memarrashidi

WC-Co ‘hard metals’ are widely used in a variety of industrial applications due to their resistance to abrasive wear, in addition to their high hardness and toughness. However, in contrast to their mechanical properties, the corrosion response of these materials is relatively poor. In the current work the corrosion mechanisms of two WC-Co cermets are analysed, with 10 and 30 vol. % of the Co metal binder, in a 3.5 wt.% NaCl aqueous solution. The assessment of corrosion involved a variety of electrochemical measurements, including open circuit potential, potentiodynamic polarisation and cyclic polarisation, together with systematic analysis of the post-corrosion solution chemistries using inductively coupled plasma optical emission spectroscopy. The corrosion potential and current density were determined, following Tafel extrapolation, allowing the calculation of the corrosion rates. It is demonstrated that continuous dissolution of the cobalt phase occurs during corrosion, which is a result of poor cermet passivation behaviour, and this response increases with the amount of binder in the cermet.

Jan 1, 2015

By George Hope, Brigitte Lacouture

"The Red Dog mine has increased mill throughput most years since start-up. Although flotation equipment has been added over the last 10 years, the Red Dog metallurgical performance has been restricted by a lack of adequate flotation capacity. Two reduced tonnage trials conducted in 1997 as well as numerous SAG relines have consistently indicated the potential to significantly increase both zinc concentrate recovery and grade with additional flotation capacity. Later in 1999, a new circuit was designed with increased flotation capacity while simplifying the current circuit, providing for three stages of dilution cleaning, and creating a retreat section. The purpose of the retreat section is to target the more complex particles and allow the chemical environment to be fine tuned for improved iron depression. In total, 21 Outokumpu OK50 (50 m3) mechanical flotation cells and four 3.66 mØ column cells were added to the current flotation circuit. The VIP (value improvement program) mill optimization project is also addressing thickening, water treatment, and power generation issues and has a total budget of US$105 M. Start-up of equipment was phased in to minimize the impact on current operations and the project was completed by the end of 2001. IntroductionRed Dog Operations started production in November 1989. The mine is located above the Arctic Circle in northwest Alaska. It is linked by an 80 km road to a port-site facility where the concentrate is stored. Concentrate is shipped to markets throughout the world during the one hundred days of open seas. As of January 2002, the Red Dog main pit had 38.4 Mt of reserves grading 19.2% Zn, 5.3% Pb, and 102 g/t Ag. Additional reserves and resources contribute an additional 72 Mt at 15.6% Zn, 4.2% Pb, and 78 g/t Ag. Red Dog is a Mississippian to Permian, black shale-hosted, zinc-lead-silver deposit located in the DeLong Mountains, western Brooks Range, Alaska. All the rocks associated with the mineralizing event are considered to be part of the exhalite rock package. Silicification was a dominant component of the mineralizing event and the host shale has been silicified and locally resembles a chert. The major sulphides in decreasing order of abundance are sphalerite, pyrite, marcasite and galena. Most of the deposit’s silver occurs within the crystal structure of the galena. The dominant ore mineral, sphalerite, is very fine grained to amorphous and is commonly intergrown with silica. Ore textures are massive, fragmental, chaotic, veined and rarely show classic sulphide sedimentary layering. The upper portion of the orebody has been physically and chemically weathered. Oxidation has altered the sulphides to sulphates. The zinc and iron sulphates are very soluble and are readily depleted from the weathered cap, while the lead sulphate is residual and is, therefore, enriched."

Jan 1, 2003

"SART technology is a useful tool for improving the economics of gold recovery from certain types of complex gold ores. SART liberates cyanide consumed by base metals such as copper, zinc and nickel, and enables the newly freed cyanide to be recycled to precious metals leaching while producing high-grade base metal sulphide concentrates for sale. The benefits of SART include the reduction in cyanide consumption, avoidance of cyanide destruction costs, minimization of risks of environmental non-compliance due to residues of cyanide destruction reporting to mine effluents, and generation of extra revenue from the sale of base metal concentrates. Concerns with SART typically include uncertainties around capital and operating costs and proper integration of SART into the overall metallurgical flowsheet. This paper presents two case studies addressing these concerns. The first involves actual costs of the full scale SART integrated into a gold heap leach operation and treating up to 500 m3/hr of leach solution at a mine in Mexico. The second involves field pilot testing and a preliminary cost estimate for integrating SART into a silver mine in Peru using Merrill Crowe.INTRODUCTION One of the current trends in the gold industry globally is the increasing importance of complex polymetallic gold deposits as discoveries of large Carlin type gold deposits become increasingly rare (Sceresini, 2005). The presence of cyanide soluble copper and zinc in complex gold deposits necessitates changes in traditional gold extraction metallurgical flowsheets. One of the tools available to the industry to help deal with interferences of cyanide-soluble base metals in gold extraction is the SART (sulphidization-acidification-recycling-thickening) process. SART breaks the weak acid dissociable (WAD) base metal-cyanide complexes, precipitates the metals as high-grade sulphide concentrates and makes the freed cyanide available for recycle. Although SART is a commercially available technology, it is still relatively new to the industry. Fewer than ten (10) full scale plants have been constructed in the past couple of decades. Some of these SART plants are small, most are located at remote sites, and the majority have not operated on a continuous basis. This has resulted in a general lack of information in the industry about the true costs, operability and metallurgical performance of SART. BQE Water has been involved in the design, construction, commissioning and operation of large scale SART plants in Mexico, Turkey and Chile and has conducted field testing programs as part of the technical assessment of SART integration into various metallurgical circuits. Having built and operated numerous plants utilizing selective sulphide precipitation of heavy metals, BQE Water has gained unique insight into the design and control of the sulphidization stage of SART to minimize costs and ensure high efficiency in cyanide recovery."

Jan 1, 2017

By Jorge Blanco, Joaquin Gotor, Enrique Delgado, Carlos Frias

Since 2009 Cobre las Cruces (CLC) has successfully operated a sustainable mining business near Seville, Spain, applying the most advanced hydrometallurgical technologies to process secondary copper sulphide ores through atmospheric leaching in ferric sulphate media and using oxygen sparging in a cascade of ten reactors. In comparison to conventional copper smelters, the CLC hydrometallurgical process does not generate SO2 gas, airborne emissions or slags. The copper ore is ground and sent directly to atmospheric leaching reactors; flotation is not required, and consequently, copper extraction is maximized at 93-95%, while producing 72,000 t/y copper cathodes of the highest purity (99.999 wt.% Cu, Grade A). Reserves for the CLC deposit were estimated at 16 million tonnes of ore averaging over 6 wt.% Cu and containing principally a chalcocite mineralization. Other copper bearing species include digenite, covellite, chalcopyrite, bornite and enargite. Pyrite represents over 70 wt.% of the ore. In the CLC leaching process, chalcocite reacts with ferric sulphate at approximately 90 ºC and copper is released into solution while ferric ions are reduced to ferrous ions. The ferric sulphate leachant is regenerated continuously by oxygen injection and consumes sulphuric acid. It is remarked that pyrite plays a crucial role to yield high copper leaching rates. When pyrite is oxidized, a small proportion of iron is co-leached and some sulphuric acid is generated. The CLC leaching technology has been designed to allow a certain level of pyrite oxidation, which is positive in many ways: (i) to maintain a Fe/Cu ratio in solution; (ii) to facilitate Fe(II) oxidation; (iii) to produce a high redox potential; and (iv) to counterbalance a bleed solution that removes some iron. Moreover, galvanic interaction between pyrite (cathode) and chalcocite (anode) can substantially increase atmospheric leaching kinetics and efficiency (copper recovery).

Jan 1, 2016