Search Documents

By A. McMullen

"IntroductionTHE LOW-VOLATILE bituminous coals of the Brazeau field, Nordegg, Alberta, are soft and weak in structure. The seams contain .bands of inferior material, locally designated 'black jack', and thin bands of friable carbonaceous shale having no definite horizon but usually 'floating' in the seam. Because of the weakness• of the coal and the friable nature of the shale bands, run-of-mine coal usually contains a very high percentage of fines, as •Shown in the following table:SIZE WEIGHT. %Plus 1/2 in 25.61/2 – 1/4 in 13.31/4 - 1/8 in 14.6Minus 1/8 in 46.5The most convenient way of cleaning the fine coal would be by treating it in association with the coarse coal, so that no additional plant would be necessary. To a limited extent this is possible in certain types of equipment, notably the jig. A system of washing without pre-sizing is not •attractive, however, when dealing with the friable coal under consideration, which contains •a preponderant proportion of fines. At the new Brazeau washery, separation is made at 3/8-inch on •a Robins 'Vibrex' •screen, the coarse sizes being cleaned in •a standard pulsator-type jig. A feldspar jig is used to clean the minus 3/8-inch fraction."

Jan 1, 1954

By L. Tang

A seismic monitoring system was installed in 2005 at Dongguashan Copper Mine, the deepest metal mine in China. Based on the seismic events monitored in situ, the possibility of rockburst prediction and prevention is investigated in this paper. The characteristics of space-timeintensity of mining-induced seismicity and the seismic response to mining are studied in detail using the seismic data in Dongguashan Mine. A conceptual model and a criterion of assessment of hazard seismic nucleation are proposed for Dongguashan Mine. In this model, the mine seismic stiffness method is adopted for rockburst prediction within the framework of the unstable failure theory. To analyze rock failure cases in Donggauashan Mine, the rate of the ratio of stiffness of rock in nucleation area to its surrounding area is proposed as a criterion for rockburst prediction.

May 1, 2009

By Richard W. Lawrence, Richard Poulin

"Numerous processes co-exist for metal extraction and for metal removal from effluents of mining operations. Each process enjoys an economic advantage, including environmental cost and benefit, if utilized in a specific situation. This applies equally to biohydrometallurgical processes. This paper will analyze four types of biohydrometallurgical processes for their economic and environmental attributes: biooxidation of refractory gold, extraction of copper from sulfide, metal removal from effluents by active sulfate reduction, and metal removal by the use of wetlands. By examining the economic and environmental advantages of these processes, generalizations can formalized and it becomes possible to define niches of application where biohydrometallurgy can be considered. Our analysis shows that biohydrometallurgy can be efficient at small scale, be more environmentally friendly than conventional technologies and is relatively easier to operate. The higher financial risk associated with unproven technologies at the commercial scale is being eliminated as biotechnology-based plants are put into production.IntroductionBiotechnology can be described as the rational exploitation of the activities of living cells or parts thereof, requiring an integrated multidisciplinary approach between biological and technical disciplines. Microbiology, biochemistry, botany, molecular biology, chemistry and engineering all contribute to practical applications in the extraction, manufacturing and service industries, and in environmental management. Considerable commercial success of biotechnology has been achieved in several sectors, including health care, agriculture, forestry and aquaculture.Over the past 40 years, industry, research organizations, government laboratories, and universities in a large number of countries have participated in investigating the utilization of biotechnology applications in mining. Today, several technologies are used commercially in well understood and engineered systems which can be grouped under the term biohydrometallurgy. Many more technologies have been demonstrated at laboratory or pilot plant scale. Although initial developments and commercial applications were aimed at metal extraction, the dramatic increase in environmental awareness, the practice of sound environmental management demanded by more stringent regulations over the past decade, and the need for low cost treatment in perpetuity, has led to serious investigation of biotechnology for environmental control. In addition, increasing power costs, lowering of ore grades, and decreasing commodity price in real dollar terms require the use of highly efficient and competitive extractive technologies."

Jan 1, 1998

By Tetsuya Yumoto, Toshikazu Shiratori

Information on the elements contained in E-Waste is important from the viewpoint of recycling. We analyzed several components of waste electrical and electronic equipment (WEEE) collected from citizens. The distributions of the minor metals in WEEE were determined with elemental mapping and chemical analyses. The annual change in elemental composition was investigated by analyzing equipment manufactured in different years. The information will be of use for separation techniques required for future advanced recycling.

Jan 1, 2011

By C. Gordon Saunders

"The ungraded-fibre mill is located at the mine site and has a rated capacity of 6,600 tons of ore input and 1,200 tons of ung1•aded fib1 •e product per day. Power for operation is obtained from a diesel generating plant located on the site, which has a capacity of 5,300 kW. The preliminary milling process consists of prima1•y and secondary crushing, drying and temporary storage of plus-1 1h -in. material. The final milling processes are two stages of crushing and three stages of screening, with air-lift separation of the fibre from the host rock. The central mill building also houses a machine shop, mill maintenance shops, a mobile equipment overhaul shop, an engine and majo1•-component overhaul shop, and a warehouse. Major changes to the milling ci1•cuits since start-up have been the addition of a larger secondary cone crusher, ct third dryer, adding a rotary distributor to the feed of the screening section and adding an automatic start-up sequence for all equipment except crushers and fans. The operation of the mill is coordinated from a central control room, where a ""mimic"" panel indicates the operation of all major units in both the ore preparation and the screening sections. Product quality is controlled by continuous sampling and frequent labo1•atory analysis, which provide data fm• the adjustment of aspirating hoods and mill feed rate. Operating problems unique to this location, and common to a sub-arctic environment, are discussed."

Jan 1, 1976

By David H. Searle

This paper will discuss the common trends existing in various Canadian jurisdictions for the closure and reclamation of mines. Included will be a discussion of the requirement to post security as well as its form and how security is calculated and refunded. Reclamation can no longer be left to the end of mine life. Progressive reclamation must occur throughout mine life and must be part of the mine plan from the beginning.

May 1, 2006

By T. R. Bieler

"Hot forming and superplasticity in powder metallurgy aluminum alloys and composites is reviewed. The effects of alloy composition, particulate composition, size, and size distribution is summarized. The role of climb distance for recovery is described in connection with the size of strengthening phases. In materials with fine strengthening phases on the order of one micron or less, high strain rate superplastic deformation processes are likely. However, the quality of superplastic deformation depends on the prior processing history, and these effects are reviewed. Very few data describing the effects of hot forming history on post-forming properties exist, but some results emerging in the literature are compared.IntroductionHot deformation in aluminum based materials is done for several technological purposes, such as thermomechanical processing to alter mechanical properties of simple forms, and/or final shaping operations to produce a complex shaped part by means of extrusion, forging, or superplastic forming. In the interest of improving the mechanical properties of aluminum based materials, two microstructural design strategies are commonly used, dispersion strengthening, and composite strengthening. The introduction of fine, stable dispersions is commonly done for high temperature strength, and the dispersions are typically ceramic particles in the range of 10 nm to 1000 nm in volume fractions around 5 vol.% (Higashi et al., 1990; 1991a; 1991b; 1992; Bieler and Mukherjee, 1990; Otsuka et al., 1987; Bieler et al., 1991; Oliver and Nix, 1982). Alternatively, composite strengthening strategies using 10-40 v% of 3 µm to 40 µm ceramic particles provide high modulus and high strength aluminum based materials (Midling and Grong, 1995; Lloyd, 1994; Subramanian et al., 1995)."

Jan 1, 1997

By Z. D. Hora

Sev_eral dozen si lica occurrences have been reported from various parts of Brit ish Columbia. Some represent hydrothermal veins or parts of pegmatite bodies; other are recrystall ized sandstones. Several vein type deposits were mined for smelter flux and as a source of white chips for stucco dash and simi lar products. Some quartzites were studied as potential sources of high-grade silica for ferrosilicon and silicon metal production. The province's only production of silica for ferrosilicon has come from a pegmatitic quartz plug near Oliver in southern British Columbia. Its reserves are now practically depleted.

Jan 1, 1984

By G. Dodbiba, A. Otsuki, T. Fujita, J. Ponou, A. Shibayama

"The different types of nano to submicron particles, which are well-dispersed nano particles, coagulated nano particles or settled submicron particles, have been measured by the interactive force apparatus (IFA). The information is very useful for mineral processing treatment. The IFA can measure the particle size distribution in low to high concentration of particles in liquids and non-light transparent liquids. Here, mainly the emulsion and bubble size measurements are described.Emulsion (w/o type) is prepared with oil and water mixture. The nano to micro emulsion particle size is usually measured by light scattering method. The particle size distribution of emulsion of light oil measured by IFA agreed well with the one by the dynamic light scattering (DLS) method. The water size distribution in emulsions of gasoline is difficult for the small reflection index and C heavy oil is difficult for the black color by DLS method. The IFA can measure both emulsions.There are many methods to measure fine air bubbles, however, the finer nano size measurement apparatuses are DLS method and IFA. A “ghost” peak appeared in the large particle micron meter size in DLS method. The mean diameter in IFA is similar with DLS for the nano meter size. INTRODUCTIONParticle size distribution measurement of nano to submicron particle, emulsion and bubble size distribution are very useful for ultrafine particle separation and characterization of fine particles by the necessity of recent fine minerals separation (For example, Li et al.2016, Mikhlin et al.2016, Wang et al.2013). As for the size measurement of solid particles in liquids, three different types of nano to submicron particles, that are well-dispersed nano particles, coagulated nano particles or settled submicron particles, have been measured by the interactive force apparatus (IFA). The particle size distributions are compared with the one of dried particles measured by TEM or SEM. The well-dispersed nano particle size distribution by IFA is influenced by the nano size surfactant micelles and becomes smaller, when compared with the TEM result. The size distribution of nano size of magnetite particles in water is influenced by the isoelectric point and the mean diameter of coagulation becomes larger. The particle coagulation in diluted suspension is about 2nm smaller when compared with the higher concentration. The submicron nickel particle size distribution is well agreed the result by SEM. The coagulation effect is small in the submicron size of nickel powder in water (Fujita et al., 2013). In this paper, the emulsion and bubble size measurements are mainly described."

Jan 1, 2016

By Hang Zhao, Xinping Li, Pingan Wu, Yi Luo

"The deep-buried rock surrounding the Jinping II Hydro-power Station was taken as the engineering background. Using model specimens of classified rock materials to simulate fractured rock mass under high in-situ stress conditions, the test about acoustic propagation law on single fracture model of specimen under different pressures and different angles were carried out. The variation of p-wave velocity in fractured rock mass and axial stress-strain relationship in the whole test procedure was also studied. Based on damage mechanics principle and the acoustic wave propagation in cracked rock mass, comparative study on damage constitutive relation of fractured rock mass under high in-situ stress in consideration of equivalent strain and equivalent energy was performed. As the results showed, with the change of axial stress level under constant confining pressure, the change in wave velocity can be divided into three stages: slow increase (small variation in amplitude), rapid reduce (large variation in amplitude ) and accelerate reduction. When the confining pressure is constant, the maximum p-wave velocity and the peak strength of specimens increases with the decrease of the crack angle.When the crack angle is constant, the maximum p-wave velocity and the peak strength of specimens increases with the increase of confining pressure.It is identified that the theoretical calculation results of constitutive relation about elasto-plastic damage model containing variable wave velocity in the fractured rock mass is consistent with the model test results.Therefore,the constitutive relation can provide reasonable suggestions for engineering practice. INTRODUCTIONThere are a lot of joints and fractures in surrounding rock mass of deep-lying in the Jinping-II hydropower station, which has a great influence on the physical and mechanical properties of rocks and effects the acoustic wave propagation and attenuation law in rock. Many previous research and project examples has proved that sound propagation parameters are closely related to crack and stress condition. Thus, it has certain theoretical significance and practical application value to carry out researches on sound propagation characteristics and establish damage constitutive model of fractured rock mass which is related to sound propagation parameters."

Jan 1, 2015

By Philip A. Dirige

This paper presents the variability of responses of paste backfill specimens that have been prepared with varying binding agent and binder combinations, when subjected to uniaxial compressive strength testing. A testing program conducted for an underground operating mine to produce cost efficient paste fill recipes using four different binding agents, in various ratios and combinations, is presented to illustrate the responses. These binding agents are Normal Portland Cement Type-10 (NPC T-10), oxidation or sulphide attack resistant binder (Binder A), replacement binder B (Binder B), and replacement binder C (Binder C). The paste fill recipes were prepared at 2, 3.5 and 5% binder content at varying binder combinations, at fixed size and tested in a Material Testing System (MTS) under constant strain rate conditions following cure times of 7, 14, 28, 56, 90, 112, 180 and 240 days. The results of tests suggested that the strength data clearly shows a trend of increasing strength with increasing binder content but not necessarily cure time. It is noted that all the blends achieved dramatic increases in strength up to 28 days of cure and then either increased or decreased moderately beyond 28 days curing, depending on the binder content and binder combination. The moderate decrease is apparent for the 2% paste fill blends and in some binder combinations of the 3.5 and 5% blends, which indicated lackluster performance beyond 28 days curing. This lackluster strength performance indicated that the binder content and combination may not be sufficient for the paste fill to achieve complete hydration and acquire adequate strength performance beyond 28 days. This study indicated that economic paste fill recipes can be designed with confidence using affordable alternative binders. However, it is noted that these alternate binders cannot be used as stand alone binders but should be used in combination with NPC to facilitate hydration of the paste fill.

May 1, 2006

By G. Avramovic-Cingara, H. J. McQueen

The microstructure of commercially pure aluminum was investigated by using polarized optical microscopy (POM), orientation imaging microscopy (OIM), and transmission electron microscopy (TEM) techniques. Specimens were deformed in torsion at 400°C and equivalent strain rate of 0.1 s-1, to various strains of 0.2, 0.5, 1, 4, and 6. The results indicate that POM can usefully reveal grain and subgrain structures over a large field in aluminum. TEM is most suitable to study dislocation substructure and evolution of subgrains. While TEM microscopy and OIM are capable of resolving individual subgrains, OIM can not reliably distinguish subgrains with small misorientations, particularly in samples with low strain. On the other hand, the OIM technique is very useful in the analysis of many regions surrounded by high, medium, and low angle boundaries (HAB, MAB, LAB). Various misorientation maps were studied using different data processing methods. The analysis revealed that the subgrain size is relatively insensitive to strain. The fraction of low LAB ( < 5°) decreased and HAB (>15°) increased conversely with increasing strain, whereas MAB (5-15°) remained stable. The development of an increasingly bimodal grain boundary misorientation distribution is consistent with the predominance of dynamic recovery (DRV) in the evolution of microstructure, combined with geometrical dynamic recrystallization (gDRX), now called grain-refining DRV.

Jan 1, 2006

By D. D. Hogarth

"IntroductionThe Hull iron range, comprising the Forsyth, Scott , Baldwin and Lawless properties (Fig. I), is in Gatineau Park, on the outskirt s o f the city of Hull , and about 6 miles (10 kilometres) northwest of the Federal Parliament Buildings.The deposits have been known many years and described numerous times, although the history has been treated lightly in former publications. Total ore shipments have been calculated at 122,700 long tons, of which over 80% were mined before 1900 and 74% in two brief periods: 1870-74 and 1880-82. It is surprising that the period 1870-74 has been overlooked by most authors and 1880-82 ignored altogether. More surprising, the essential data for these two periods are contained in manuscripts of the Robert Bell collection, which must have been available to officers of the Geological Survey o f Canada.The period 1801-1874 ha s already been covered by the writer in ""Pioneer mines”, but much information has come to light since publication. The present paper is therefore based o n new data and a fresh appraisal. However, little additional data were found for the early history (1801-1854) or for the legal cases involving A.H. Baldwin, and these parts were mainly summarized from the relevant sections of the above-mentioned publication.GeologyThe ore deposits are all situated somewhat below the middle of a graphitic, calcitic marble horizon, here folded into a northeast-plunging synform. The Forsyth, Scott and Baldwin deposits are on the south limb of the synform; the Lawless is on the north limb. The marble is underlain by three non-carbonate groups: biotite gneiss with interlayered quartzite (top), granite gneiss and skarn (middle), and biotite-garnet gneiss (bottom). Below these groups is a lower horizon of graphitic, calcitic marble. The whole sequence is Precambrian and has been subjected to high-grade (Grenvillian) metamorphism, but, in the north, is cut by an unmetamorphosed Cambro-Ordovician diabase dyke. For further information, the reader is referred to the summary by Baird."

Jan 1, 1983

By Diankun Lu, Ganfeng Tu, Edouard Asselin, Feng Xie

A novel separation process for detoxifying cadmium-containing residues arising from zinc hydrometallurgical processes has been developed. An initial investigation indicated that a high concentration of zinc in the sulfate solution can be effectively separated from cadmium by solvent extraction with P204 (di(2-ethylhexly)phosphoric acid, D2EHPA). The mixture of sulfuric acid and ammonium citrate ((NH4)3C6H5O7) is thus used to extract metals from the residue at room temperature. Copper in the leachate is recovered by solvent extraction (SX) with LIX 973. Cobalt in the raffinate from the copper SX process is recovered by precipitation with a-nitroso-ß-naphthol. The results show that more than 50% of the copper and virtually all the zinc, cadmium and cobalt in the residue can be leached under the experimental conditions used here. Virtually all dissolved copper and cobalt can be recovered in the subsequent solvent extraction and precipitation processes. The presence of (NH4)3C6H5O7 could significantly facilitate the extraction of zinc by D2EHPA in the subsequent separation of zinc and cadmium. More than 97% of the dissolved zinc can be recovered through a two-stage counter current solvent extraction process. After separating copper, cobalt and zinc, cadmium can easily be recovered from the solution either by cementation with zinc powder or by electrowinning, while the purified solution can be recycled back to the leaching process.

Jan 1, 2014

By V. K. Karra

"A simplistic algorithm jar simulating the rod or ball mill Bond grindability test applied to ores and minerals is presented. A performance comparison between the present algorithm and a previously published algorithm by Kapurot, modified in this work jar a fair evaluation, is also given. A worked example is furnished jar leading the reader through the various calculations.IntroductionThe Bond grindability test is widely used for the prediction of the power requirement of an industrial grinding mill. The procedures for conducting this test in either a ball or a rod mill are available(1). In the case of a ball mill, batch grind abilities have been correlated to Bond grindabilities to help monitor day-today variations in ore grindability for the purpose of plant control( 2,3). Of special interest is the algorithm presented by Kapur(3) for the simulation of the Bond test. In practice, the test lasts from 6 to 14 cycles (4 to 10 hours). With this algorithm, one can predict the Bond grind ability using information available from only the first two cycles.Sometimes the prepared feed for the grindability test contains too much fines compared to the total product desired at the mesh of grind under consideration. In such a case, the operator separates the fines from the test feed and adds to the remaining coarse fraction an equal amount of fresh feed. This combined feed then forms the feed to the first cycle of the test. In the present work, Kapur&apos;s algorithm is modified to include this special case. A new and relatively simpler algorithm is also presented. Statistical equations relating work index to pertinent variables are also given."

Jan 1, 1981

The hydrometallurgical treatment of copper ores and concentrates continues to be an active field of innovation. The direct extraction of copper from ores containing chalcopyrite is an important development to provide an alternative to flotation-smelting and refining. Jetti Resources (with the University of British Columbia) and the JX Nippon Group have developed process options for chalcopyrite heap leaching. Biological heap leaching developments for chalcopyrite are also continuing in parallel. These direct leaching technologies are also very attractive for arsenical ores. The atmospheric leaching of copper concentrates is an attractive option along with autoclave processing. The Galvanox™ Process is the focus of commercialization by InCoR Galvanox Holdings under exclusive license by the University of British Columbia. The Galvanox™ Process can be used to treat chalcopyrite or enargite containing concentrates to high copper extraction with simultaneous precipitation of arsenic as atmospheric scorodite. FLSmidth has continued development of the Rapid Oxidative Leach (ROL) and associated technologies for chalcopyrite leaching. The Glencore Albion Copper Process using ultra fine grinding of copper concentrates and atmospheric leaching has found application in central Africa. The pressure leaching of copper concentrates continues to be attractive for rapid, complete oxidation of sulfide minerals with high copper extraction and arsenic stabilization of iron-arsenate minerals and precipitates. The Ecometales PLCC project is designed to use high temperature total pressure oxidation for treatment of an arsenical copper concentrate with use of existing copper SX-EW facilities for copper cathode production. The excess acid from the autoclave process will be used to make up the acid demand for associated copper ore heap and dump leaching operations. INTRODUCTION The recovery of copper from ores is dominated by the flotation of copper concentrates followed by smelting—converting and electrorefining. This process has been enabled by the development of froth flotation and progressively made more efficient by advances in smelting and converting technologies.

Jan 1, 2019

By X. S. Fan, T. R. Feng, D. Chen

To meet the flotation process requirements, the large-scale flotation cell must be designed for sufficient pulp mixing, reasonable air dispersion and solid suspension, which is very difficult to design for super large-scale flotation cell. Hence, the flotation cell scale-up and optimization for a short period is a challenge for super large-scale flotation cell design. Computational fluid dynamics simulation has been applied in flotation cell study, which is effective, timesaving and low cost in the study of the flow field distribution for super large-scale flotation cell. This paper demonstrates the flow field characteristics in the 600m3 flotation cell by CFD. The flotation cell model is meshed with hexahedral grid and the high mesh quality assures the computational precision. MRF model, namely a steady-state approximation, ensures that individual cell zones can be assigned different rotational speed. Euler-Euler approach is chosen for multiphase flow simulation to treat different phases as interpenetrating continua. Numerical simulation of single phase, two-phase and three-phase are investigated respectively. Results suggested that the flotation cell has the apparent upper and lower flow circulation. In condition of the impeller rotation, the air is dispersed reasonably. In addition, the solid phase volume concentration distribution in the cell has a little difference.

Jan 1, 2015

By Laura Mottola

This paper outlines a framework for ensuring the success of the implementation phase that follows research and development of new mining technologies and systems. It is based upon recent and past lessons learned that have demonstrated the critical challenges to effective technology transfer, which frequently receive inadequate attention within the culture of the mining business. The paper focuses on mining automation implementation challenges and then outlines a Roadmap which is proposed as an integrated framework to deal with the key aspects of people, process and technology. This framework is built upon: assembly of a Strategic Team to develop a Roadmap; fully understanding the business requirements of the technology initiative; defining Key Performance Indicators in a Balanced Score Card; performing a Stakeholder Analysis to identify the affected groups; and finally developing a master Project Plan to execute the Roadmap.

Oct 1, 2009

By P. W. Waggitt

ABSTRACT From approximately 1986 until 2000, uranium production was at a historic low. In 2003, uranium mineral exploration surged, despite the global financial crisis; however, the shortage and aging of qualified and experienced operators and regulators might soon become a constraint to this upsurge. This is true for all types of engineers, geologists, other scientists, tradespeople, and technicians. The situation raises questions about how the global mining industry in general and the uranium sector in particular will cope with future staffing needs. In this paper, the author examines the current situation and describes how some organizations are seeking possible solutions.

Jan 1, 2014

By R. Spring

"Soft-sensors are a computer software alternative to inadequate hardware instrumentation. Filters are averaging methods that reduce the noise in any sensor&apos;s signal. This paper introduces these topics and places them in a mineral processing context using then-product formula.Soft SensorsAs their name implies, ""soft-sensors"" are computer programs that estimate values for process variables (Tham, 1991). This approach is useful when the appropriate hardware sensor does not exist, is deficient, supplies only infrequent values, etc. For example, in mineral concentrators the traditional magnetic flowmeter/ nuclear density gauge instrumentation for measuring slurry flows costs $5,000 or more per flow and requires frequent maintenance. However, metal assays are commonly available from online X-ray fluorescence analyzers and application of the n-product formula (Taggart, 1945) to these assays conveniently provides software estimates of the flowrates (albeit only when the circuit is in steady-state).Soft-sensors are used by inferential controllers that base their control actions on the process values ""inferred"" by the soft-sensor. Such was the case at Brenda Mines where the rod mill feed tonnage controller used an inferred value of the cyclone overflow particle size (Bradburn, 1976). It was also the case at Brunswick Mining where reagent controllers adjusted reagent addition rates throughout the plant according to the various ore flowrates inferred by an expert system (Spring, 1991). A unique feature of the expert system soft-sensor was its dynamic flow models which compensated for residence times, material transport lags, etc. Thus the soft-sensor values were valid under both steady-state and nonsteady- state conditions."

Jan 1, 1992