Search Documents

By H. Wotruba, J. Heizmann

"The use of shotcrete is a mandatory means for rock support and therefore for safety in many underground mining operations. If shotcrete gets into the flotation feed though, it can negatively influence the flotation process. This especially occurs when sublevel stoping, cut-and-fill or room-and-pillar methods are applied because as the mining face moves on, formerly applied shotcrete layers are mined together with the ore.As shotcrete does not differ significantly from fluorspar ore in its physical properties it gets moved through the comminution process and is fed to the flotation plant like the ore. To prove the influence of shotcrete on the flotation process, a laboratory test series was conducted at the Unit of Mineral Processing (AMR) of the RWTH Aachen University. The shotcrete grade of the flotation feed was varied between 0 and 10% through addition of pure shotcrete. Flotation parameters and also reagent dosage were held constant apart from the addition of the pH regulator, which was dosed to reach a constant pH of 8 at the flotation start. Results showed that with increasing shotcrete grades in the flotation feed the fluorspar recovery as well as general mass recovery decreased. The enrichment factor of Fluorspar also decreased with increasing shotcrete grades in the feed.In an effort to eliminate the shotcrete contamination of the flotation feed, a feasibility study for use of sensor-based sorting prior to the comminution process was conducted. Rock sorting not only reduces the bad influence of shotcrete on the flotation process, but also reduces comminution costs. INTRODUCTIONShotcrete is used in underground mining on a regular basis. It is used for rock support and therefore to increase safety in the underground mining environment. In mineral processing the presence of shotcrete can cause difficulties for example in the concentration processes. In flotation the highly sensitive reagent mixtures can be disturbed by the chemical activity of shotcrete and therefore recovery rates and selectivity of the process can suffer.Shotcrete is a special form of concrete which is applied pneumatically with high velocities and is compressed by its impact energy. Since the process is especially suitable for work in difficult environments and overhead areas, it is established in underground mining for many years. Shotcrete is not only applied in pre-processing of the mines, but particularly of use for cut and fill, as well as room and pillar mining methods. There it is used to secure excavation chambers. When the mine face is secured with shotcrete and subsequently the mining continues, the applied shotcrete will automatically be mixed with the ore."

Jan 1, 2016

By Michel Ruel

"This paper describes how to make advanced control choices when difficult processes need improvement. The decision-making process involves choosing between a rules-based approach and a model-based approach as well as weighing benefits and drawbacks, complexity and simplicity, investment and results. This paper will present briefly each solution: basic control, advanced regulatory control, model predictive control, and expert systems such as fuzzy logic controllers and neural networks. The article then proposes a decision tree for selecting the most appropriate approach. A table will compare usage, development, commissioning, maintenance and lifecycle costs for each approach. Finally, conclusions and suggestions will summarize the methodology.INTRODUCTION Advanced process control (APC) is a popular topic. How can one decide whether advanced control should be added to an existing system? Advanced control is used to improve performance, stabilize production, handle constraints, protect equipment and manage grade changes. Most plants use feedback controllers, usually PID (proportional, integral, derivative) controllers. It is common to develop special control schemes to handle more complex processes. In classic PID process control, a controller brings a single value close to a set point using a single manipulated variable. On the other hand, APC brings several values close to optimal targets simultaneously using several manipulated variables. APC's four main strategies are advanced regulatory control, model predictive control (MPC), fuzzy logic and neural networks. Simple solutions are always preferred. Complexity will be increased if performances (production, quality, etc.) are below par. Profitability analyses should be conducted to validate project viability. Needs—not trends—should dictate choices! Before increasing complexity, it is important to define needs, goals, technical support, budget, etc. All these approaches entail strengths and weaknesses. Building a project based on technology rather than needs spells trouble."

Jan 1, 2014

By Leslie McHattie, Sadek E. EI-Alfy

"The Maintenance Engineering Department at Carol Mining and Concentrating is currently in the process of introducing reliability concepts such as failure analysis, rework elimination, predictive maintenance, computerized maintenance history analysis, etc. to improve the over-all maintenance function in the mine and concentratormaintenance areas. Some current initiatives include:• Implementation ofan infrared thermographic scanning program.• Ultrasonic inspection of shafts for all critical equipment in the mine and concentrator areas.• Non-destructive testing of all major welds done by maintenance personnel.• Development of an effective vibration monitoring and analysis program for the production equipment in the mine (shovels, drills, haulage trucks, locomotives).• Failure analysis performed by maintenance engineers to identify the root cause of component failures on critical production equipment.• Computerized breakdown analysis to identify the recurring component failures which contribute significantly to high maintenance costs and production loss.• Implementation of a computerized maintenance management information system.This paper will outline the planned implementation ofthese initiatives, and others, and will also cover the status and results obtained to date."

Jan 1, 1992

By K. Ihara, T. Yamaguchi, K. Matsumoto

"Al-Fe alloy sheets having layers with different strain components were produced by unlubricated hot rolling and the recrystallization texture formation during annealing was investigated in each layer. In this study, the strain component introduced by rolling was quantitatively evaluated by measuring degree of bending of an aluminum pin embedded in the sheet. The textures before and after annealing were investigated by the SEM-EBSD technique. It was clarified that, in the middle layer, where comparatively small shear strain was introduced, ß-fiber subgrains and cube {001}<100> oriented subgrains were formed before annealing, and cube oriented recrystallized grains grew after annealing. On the other hand, in the surface layer, where large additional shear strain was introduced, shear texture components and cube oriented subgrains were formed before annealing, and shear texture was retained even after annealing, while cube oriented subgrains did not grow and were encroached. It was suggested that introduced strain components influenced the recrystallization texture formation by inducing different distribution of the subgrain size, stored strain energy and orientation relationship with surroundings before annealing.INTRODUCTION The microstructure developed during the hot-rolling process of aluminum and aluminum alloys affect the mechanical properties of the final product sheets. Especially, the crystallographic orientation in the final product sheets affects the r- value and ears during deep drawing (Humphreys & Hatherly, 2004), then the texture control in the hot-rolling process is important. When the friction between the rolling roll and rolled sheet in the hot-rolling is large, both the rolling texture and recrystallization texture tend to be heterogeneous in the thickness direction. It is known in many rolled aluminum alloy sheets that the texture in the surface layer was different from that in the middle layer because of additional shear strain. It was reported that in the vicinity of the surface layer, where large additional shear strain was introduced, the shear texture <1 1 1>//ND and < 1 1 0> // RD which contain components of {1 1 1} <1 1 0> and {0 0 1} <1 1 0> developed during rolling, and the shear texture developed even after recrystallization annealing (Sakai et al., 2002). Particularly, it is thought that the <1 1 1> // ND texture contributes to improve the r-value and press formability (Inoue & Takasugi, 2007). Therefore, asymmetrical rolling and high friction rolling have been applied to improve formability of aluminum alloys by adding shear strain in the rolled sheets as deep as possible (Kamijo et al., 1972; Inoue et al., 2005). However, few researches have been focused on the microstructures and texture before annealing and thus, the detailed mechanism is still unclear how the texture after annealing is affected by the texture before annealing. In this study, the Al-Fe alloy of commercially pure aluminum was chosen as the first material to be studied in order to clarify the fundamental process of the recrystallization texture formation. The main purpose of this study is to clarify the effect of additional shear strain on the rolling and recrystallization textures in the hot-rolled sheets by analyzing the transition of microstructure and orientation distribution through recrystallization annealing."

Jan 1, 2018

By Michel Chouteau

"A very conductive zone was revealed in 1977 and 1978 by magnetotelluric (MT) measurements carried out near Ste-Mathilde, 6 km northeast of La Malbaie . In order to identify the structure causing the anomaly, thirty-five MT soundings were recorded in 1980 and 1981 on and around the conductor within a radius of4 km. Results confirmed that the conductor is of limited extent (less than 2 km by 0.4 km). The proposed model is a highly conductive vertical slab, the top of which is within 200 m from the surface. At a depth of approximately 825 m this structure joins a conductive layer which extends to the northwest but not to the southeast. The large conductivities and the depths involved can only be explain ed by a fractured zone flooded with electrolytic solutions, by graphite veins or by metallic mineralization (sulphides). The former seems to be the most likely hypothesis because an EW fault running across this zone could have allowed percolation of water and the leaching of disseminated pyrite out of a mylolisthenite filling the fault.IntroductionLa Malbaie is located 130 km northeast of Quebec City on th e North Shore o f the St. Lawrence River (Fig. I). Four major groups o f rocks have been mapped in this area: charnockitic rocks to the west , granitic rocks in the north east and southeast, gneiss and pegmatites northwest and south of La Malbaie , and Paleozoic sediments in the Clermont-La Malbaie Valley and along the shore of the St. Lawrence River (Rondot, 1966). Two major features dominate the structure of the region: Logan &apos; s line , a major thrust fault beneath the St. Lawrence which separates the Grenville Province to the north from the Appalachian regime to the south, and the Charlevoix Crater , a large Paleozoic impact crater that created an almost perfect annula r structure centred on Mont des Eboulements (Rondot, 1970). Ste-Mathilde is a village lying 6 km northeast of La Malbaie, just outside the ring-like graben zone caused by readjustments after meteorite impact. The survey area spreads over a granite body which is more than 2 km long and 0.6 km wide, surrounded by a wide migmatite zone which is injected by many bodies of pegmatite, the latter likely related to the granite body (Fig. 2). A zone of leptynites lies west of the area. An east-west trending fault (FA1) related to the Charlevoix Crater runs mid -way across the survey area; a second parallel fault (FA2) south of FAI separates the gneissic rocks from the Paleozoic sediments. The overburden is usually thin with outcrops frequently encountered except for the centre of the survey are a where 10 m of glacial sediments are expected (E. Gaucher, 1982, personal communication)."

Jan 1, 1985

By H. Nakano

The codeposition behavior of impurities such as Ag, Bi, Fe, Ni, Pb and Sb with Cu was investigated galvanostatically at 5-3000 A/m2 using a Pt cathode at 60 °C in acidic copper (I) chloride (cuprous chloride) solution at pH1-2 containing 1.0 mol/L of Cu+ and 4.9 mol/L of Cl-. The impurities were classified into two groups: Group I (Ag, Bi) which codeposits with Cu as a metal, and Group II (Fe, Ni, Pb, Sb) which is slightly involved in the deposited Cu in nonmetal form from the electrolyte. Silver and Bi in Group I behaved as more noble metals than Cu, and significantly codeposited with Cu, showing typical features of regular-type codeposition. When Cu was deposited dendritically, the Ag and Bi content in the deposit increased with increased duration of electrolysis as a result of decreased net current density caused by increased cathode area. The current efficiency for Cu deposition in impurity-free solution was 95-100% over 100-1000 A/m2, but it abruptly decreased at above 1000 A/m2 when the limiting current density of Cu was attained. Although Fe, Ni, Pb and Sb in Group II were involved to 0.01-0.02 mass% in the deposit, they had no influence on the current efficiency or morphology of Cu.

Jan 1, 2007

By J. Maheu

Heap leaching is an old technique for the recovery of copper, but a fairly new technique for the recovery of gold.The paper outlines the equipment required for the establishment of heap leaching test facilities and the procedure required to insure meaningful results. Sampling methods, the metal balance, carbon adsorption and stripping and safety procedures are discussed in broad outline.

Jan 1, 1982

By Ning Yu

There are about 1.341 trillion tons (t) of proven coal reserves in China, of which 279.58 billion t are available for mine well construction basis. Thick coal seams are 44% of the reserves. The production of thick coal seams exploitation is over 45% of the total coal production. Full-seam mining and fully-mechanized mining for large mining height is the technology development direction of thick and extra thick seam mining. It is also the important way to achieve efficient and intensive mining with the characteristics of high production, high mechanization, high efficiency and low energy consumption, etc. Complete set of technology and equipment of fully-mechanized top caving for large mining height of full-seam (7m) mining and extra thick seam ( 14-20m) has been gradually mature and for demonstration application by the joint research of government, enterprises, universities, scientific research organizations and users. It has solved some technical problems of coal face for large mining height (over 7m) such as the coal wall spalling control, stability of support, wall rock coupling, cooperation work of mining and caving, full roadway support for super large section, end support, equipment matching of coal shearers, hydraulic support and scraper conveyor. It has developed key equipments including powerful hydraulic support of fully-mechanized mining and fully-mechanized top caving for large mining height, electrically-driven coal shearer with high speed and reliability, scraper and belt conveyer with big capacity, soft-start and high reliability, automatic control system of coal face with the core of electric-hydraulic control, bolting drill boom large section coal roadway shearer, heavy auxiliary transport equipment. The operation rates of fully-mechanized top caving equipment for full-seam and large mining height are 94% and 92.1%, and recovery ratios are 93.6% and 88.9% respectively. The annual raw coal production of single work face is over 10 Mt. The automation and intelligentization level have been clearly improved. The exploitation of thick and extra thick coal seam that is safe and efficient has been achieved in China.

Aug 1, 2013

By J. M. Shneerson

Gipronickel Institute, Saint-Petersburg will The copper concentrate was extracted from copper and nickel matte after its hydrometallurgical treatment and nickel removal. The concentrate containing 60-74% of copper was represented by two principal copper minerals, digenite and covellite. The oxidising leaching of this kind of concentrate was studied at the Gipronickel Institute. The effect of key parameters, such as temperature, oxygen partial pressure and initial solution compound, on the rate of copper dissolution and transfer of sulphur from sulphide to elemental form was investigated. It was shown that at temperatures about 90DC, the sulphur content of covellite converts to elemental form. Under autoclave conditions at 11ODC, the elemental sulphur dissolves as a sulphate-ion. At the temperature range from 50 to 90DC, the copper dissolution rate is in direct relation with temperature. By increasing the temperature to 130DC, this effect is reversed. Based on the research work, a technological flow sheet for the leaching of the copper concentrate was developed.

Jan 1, 2007

By Peter Fullagar, Adel Vatandoost, Steve Walters, Toni Kojovic

"Traditional comminution tests are a vital component in every mine plant design. Comminution behavior governs both the cost of equipment and its operating efficiency. Most comminution tests are conducted off site on a limited number of samples, owing to the high costs and long lead times involved. Therefore a strong incentive exists to find alternative means for efficiently characterizing comminution behavior for a truly representative suite of samples. The potential for inferring comminution behavior from drill core is investigated in this paper. Our approach involves development of small scale comminution tests on the one hand, and measurement of a wide range of core attributes on the other. Our focus is the relationship between petrophysical properties and comminution behavior.Petrophysical properties of archival diamond drill core from the Ernest Henry Mine (Queensland, Australia) have been measured using a Geotek multi-sensor petrophysical core logger. We have investigated the relationship between the petrophysical properties and the corresponding small scale A*b and estimated Bond mill work index test results for 2m composites of the core. Core samples were petrophysically classified by means of cluster analysis. Comminution behaviour was then modeled for each cluster via multiple regression. The results suggest that prediction of the comminution behavior on the basis of petrophysics is viable at Ernest Henry.INTRODUCTIONMineral processing is the most important downstream operation for mining engineers and metallurgists since most mined materials are subjected to some type of comminution or beneficiation operation (SME, 1992). Comminution or size reduction is typically the first stage of processing. Size reduction steps (crushing and grinding) in any plant consume large amounts of energy, normally more than 50% of total energy (Weiss, 1985). Therefore, it is desirable to obtain laboratory results to design the size reduction equipment appropriately. One of the main factors that control the selection of hard-rock crushing equipment and the design of a crushing circuit is the mechanical character of the ore(s). Work index, density, abrasivity, compressive strength and clay content are essential parameters for ore characterisation (SME, 1992)."

Jan 1, 2009

By Norman M. P. Low

"IntroductionIndustrial applications of mica utilize two commercially important varieties of mica: muscovite and phlogopite. Muscovite mica is a potassium mica with a general chemical formula, H2KA1(Si04)3 h, and is sometimes referred to as a potas hsilicate. Phlogopite is a magnesium mica having a general chemical formula, H2KMgSi(Si04)3, and is distinguished from the muscovite mica by its decomposition in sulphuric acid.Canada is one of the major natural mica producers in the world. A large tonnage of the mica powders is at present mined and processed in the Eastern Townships of Quebec. This Canadian mica is of the phlogopite type. A closely related mineral of the mica family which is widely used in the construction industry is vermiculite. It is a dehydrated magnesium-aluminum-iron silicate characterized by a foliated structure. Expanded vermiculite, which is often referred to as exfoliated mica, is used as many types of thermal and acoustic insulation, as loose fill in buildings, as an aggregate in concrete, as an ingredient in plaster and insulating concrete , and in fire-proofing compositions. Natural phlogopite and muscovite mica powders are used extensively as reinforcing agents in organic polymers. They also have a wide range of applications in commerical products. For example, dry-ground mica powders are used in large tonnage as a surface finish in roofing materials and as a bonding agent in wallboard joint cement. Common products such as paint, rubber, plastics and welding rods contain mica. Recent studies have also shown that mica powders can be added to portland cement in the preparation of concrete products, as they could improve the tensile strength of the concrete products. The potential and possible"

Jan 1, 1982

By C. R. Tang

The respirable dust real-time monitoring equipment export information is complex, and electromagnetic wave wireless transmission is affected largely under mine conditions. The respirable dust concentration information transmission method based on led light equipment is proposed. The respirable dust concentration data of the individual real-time monitoring equipment is encoded to fit the system transmission; the encoded signal is modulated onto the LED mine lamp; the light signal is transmitted by the spatial channel; the signal is received by the receiver to the photoelectric conversion to restore the respirable dust concentration data for subsequent processing. Simulation and verification experiments showed that the respirable dust concentration information transmission method based on led light equipment can achieve the LED miners? lamps visible light wireless data transmission.

Aug 1, 2013

By Mario Bureau

Need for a lab assembly reaching better and consistent static anchorage capacities

May 1, 2013

By K. Meyer, M. E. Goddfellow

"At Teck-Corona Operating Corporation's David Bell Mine, a water quality management strategy is employed to produce both a chemically and biologically clean effluent prior to discharge to the environment.The strategy includes operating methods to minimize contaminants leaving the concentrator and an effluent treatment plant for cyanide, antimony, and heavy metal removal of concentrator, mine and site waste streams.Concentrator practices, the effluent treatment plant, process chemistry and the present day performance of the water quality management strategy are reviewed.INTRODUCTIONThe David Bell Mine is located in the Hernia gold camp 35 km east of Marathon, Ontario. The concentrator has a design throughput of 1,000 tonnes per day. ROM ore (-6"") is ground in a semi-autogenous mill followed by a ball mill, thickener, leaching, and carbon-in-pulp gold recovery unit operations. The concentrator flow sheet is shown in Figure 1."

Jan 1, 1991

By R. W. Baker

"The development of uppers drilling at Brunswick Mining is reviewed. This paper describes design criteria for drilling patterns and the research required for selection of a suitable drill jumbo. The success of the uppers drilling program based on operating procedures is highlighted. IntroductionBrunswick Mining and Smelting Corporation Ltd., operates a 10 500 tonnes per day lead /zinc/copper I silver underground mine some seventeen miles southwest of Bathurst, New Brunswick .The No. 12 orebody, first discovered in 1952 by a group headed by M.J. Boylen, had extensive development, including two shallow shafts (500 ft), and test work carried out on it by St. Joe Lead between 1953-1957. However due to complex metallurgy and depressed metal prices, the operation was suspended.In 1961, a group comprised of M.J . Boylen, K.C . Irving and Patino acquired the rights of St. Joe Lead to the No. 12 property. A concerted development plan was initiated along with construction of the necessary sur face facilities and by July 1964, the property was in production at 4500 tons per day.In 1967 Noranda Mines Ltd. acquired operating control of Brunswick Mining and Smelting Corporation Ltd."

Jan 1, 1988

By H. Dundar

An extensive testwork was performed around the HPGR plant at GoldFields Ghana Limited Tarkwa Gold Mine. The HPGR was used to prepare the feed for heap leaching. The circuit was configured in such a way that the edge material from the HPGR discharge was recycled for further crushing while the product from the centre reported to the heap leach section. The set-up of the Polysius HPGR provided an opportunity to study the effect of different design and operating variables. This paper will discuss the results from the tests performed to assess the effect of rolls? speed and applied pressure on the capacity and the grinding efficiency of the HPGR. Applying different pressure values appeared to have an influence on the amount of edge material recycled.

Jan 1, 2012

By A. J. Neale, B. C. Flintoff

"A review of the dynamic rod mill-ball mill grinding circuit simulator developed at the University of Alberta, highlighting the modular structure and open-ended design, demonstrates the ease with which classical feedback control strategies can be designed and implemented. Various open loop simulations are presented to demonstrate the highly interactive nature of the grinding circuit and to indicate where potential control problems may be encountered. Closed loop simulations are examined, beginning with the basic SISO classical feedback control of circuit product size. Further improvement in the grinding circuit performance in the presence of various disturbances is realized through the application of a classical MIMO feedback controller. As an example of advanced (multivariable) control, static decoupling is implemented and shown to provide additional improvement in overall circuit performance.INTRODUCTIONIt has long been recognized in the processing industries that a dynamic process simulator is an indispensable tool in the design and evaluation of automatic control schemes. In mineral processing the lack of these simulators is felt to have been a major hindrance to the widespread implementation of effective process control systems. In particular dynamic simulation is a necessary precursor to any study of modern (as opposed to classical) process control methods. This paper discusses the development of a dynamic simulator that can be used to study various feedback control strategies. The simulation software provides a powerful educational tool for those individuals interested in grinding circuit control."

Jan 1, 1988

By C. A. Godden, T. N. Atkinson

Metallographic techniques developed from studies of corrosion films and electroplated coatings on aluminum alloys, are discussed. These methods, the result of work at the Naval Research Establishment, give extremely flat fields at the interface despite the large difference in hardness, in cases where electrolytic polishing could not be used. Techniques to overcome the similarity in refractive index of immersion oil, aluminum ox1d~, and mounting plastic are also considered, as are methods for improving visual and photographic contrast in areas of interest. A device for marking specimens is also de-scribed. ELE•CTROLYTIC polishing is inapplicable in the study of surface films on aluminum, whether corrosion films or electrodeposits. Mechanical procedures must there-fore be followed. Sample flatness and edge retention are of paramount importance. Special measures are required in the study of oxide films, because of the close proximity of the refractive indices of aluminum oxide, mounting plastic, and immersion oil.

Jan 1, 1962

By Michael Schindler

Uranyl mineral dissolution appears to be complex, affected by factors such as solution pH and the presence of various cations in solution, and sometimes involving formation of secondary surface precipitates. Such secondary precipitates potentially could armor the underlying uranyl mineral surfaces from further dissolution. A detailed understanding on the formation of secondary precipitate is therefore essential for predictive modeling of radionuclide fate and transport in the subsurface. Several types of secondary precipitates on the surface of uranyl minerals were examined using Atomic Force Microscopy, Scanning Electron Microscopy, and, Xray Photoelectron Spectroscopy.

Aug 1, 2010

By Wei Zhang, Jinhong Zhang

"The adsorption of ethyl xanthate on copper sulfides, i.e., chalcopyrite, chalcocite and bornite, has been studied in situ in aqueous solutions by applying an atomic force microscopy (AFM). AFM images show that xanthate, such as potassium ethyl xanthate (KEX), adsorbs strongly on chalcocite and bornite mainly in the form of insoluble metal xanthate, which binds strongly with the mineral surface without being removed by flushing with ethanol alcohol. This adsorption mechanism is totally different from the one obtained with chalcopyrite/xanthate system, during which oily dixanthogen is the main adsorption product on chalcopyrite surface. The findings obtained from the present AFM study suggest that an AFM image analysis is a powerful tool for the study of the collector’s adsorption on mineral surface and as well the development of novel collector for copper sulfide flotation.INTRODUCTIONIn mining industry, copper sulfide minerals, i.e., chalcopyrite, chalcocite and bornite, are usually separated selectively from non-valuable gangue by froth flotation, which treats the highest throughput and produces the maximum economic outcome of any surface chemistry process. In flotation, collectors are added into the pulp (mixture of water and fine-grained minerals) to selectively adsorb onto the target mineral and render its surface with high hydrophobicity, which is generally beneficial for a strong mineralbubble attachment and thus a high flotation recovery.The adsorption of collector on mineral surface, therefore, is vital for a successful flotation process and it has been studied by applying various surface analysis techniques, such as IR (Infrared Spectroscopy), CV (Cyclic Voltammetry) and XPS (X-ray Photoelectron Spectroscopy). (Poling, 1963; Allison et al., 1972; Mielczarski et al., 1984; Leppinen et al., 1989; Kartio et al., 1996) These studies have revealed a lot of information, such as the reaction, product and mechanism, of the adsorption of chemicals on mineral surface. It is also of great interest to directly get the image of adsorbed collectors on mineral surface changing with pulp chemistry, such as pH, redox potential, ionic strength and chemical’s dosage."

Jan 1, 2016