Search Documents

By J. Kang

There is increasing demand to utilize aluminium alloy sheets and their spot welds by the automotive industry. While traditional uniaxial tensile tests only determine mechanical properties to small strain, direct measurement of the constitutive behaviour of aluminium alloy spot welds at large strain remains a challenge. A technique was successfully developed using digital image correlation coupled with shear tests to directly measure the constitutive behaviour of an AA6022-T4 spot weld to large strains. The results show that the spot welding process not only decreases the yield strength but also lowers the work hardening rate of the nugget versus the base material. Details of sample preparation, experimental approach and results will be discussed.

Jan 1, 2011

By Liang Zhen, Jian-Tang Jiang, Guo-Ai Li, Xiao-Ya Wang

"Deformation behavior of 2A97 aluminum alloy containing coarse secondary phases was studied using uniaxial hot compression (HC, 340–490°C, 0.4001–1 s-1). The flow stress could be described by a Zener-Hollomon parameter in hyperbolic sine function with the hot deformation activation energy of 237 kJ/mol. Based on the experimental data and dynamic materials model, processing maps were generated to demonstrate the hot workability of the alloy. The coarse secondary phases experienced dissolution by varying degree under different deformation temperature, which producing different effects on the microstructure evolution. When deformed at relatively low temperatures, a mass of fine grains shaped up in the original grains and grain boundaries, and the dominating deformation mechanism was believed to be dynamic recrystallization. As the deformation temperature rising to 490°C, most secondary phases disappeared and few recrystallized grains were observed, indicating that the secondary phases dissolved sufficiently along with dynamic recovery occurred during the hot deformation. Particle stimulated nucleation related to the coarse secondary phases was believed to promote the recrystallization and the recrystallization behavior was sensitive to deformation temperature.INTRODUCTION Al-Li alloys has received much attention as new promising structural materials in the aircraft and aerospace industries, due to their lower density, higher elastic modulus and improved fatigue crack growth resistance in comparison with the conventional commercial aluminum alloys (Ou Ling, 2015). 2A97 alloy is one of the 3rd generation Al-Li alloys targeting at comprehensive improvement of aviation aluminum alloy and applications for wing spars and ribs to other internal structures for transport aircraft. Al-Li alloys are usually formed by hot deformation, either by rolling or extruding. The deformation behavior and resulted microstructure evolution during the forming process mainly dominates the formability of the alloy and the serving performances as well. Therefore, the deformation behavior and microstructure evolution at elevated temperature need be made clear for optimizing the hot processing parameters and controlling microstructure evolution."

Jan 1, 2018

The influence of joint orientation and joint persistence, on the mechanical behaviour of jointed rock masses under uniaxial compression, has been studied systematically. The joint inclination angle ß was varied from 0° to 90° with an increment of 15°. The joint continuity factor k was taken as 0.2, 0.4, 0.6 and 0.8. The peak strength, Young’s modulus, the complete axial stress-axial strain curves, the cracking process and the characteristic of the fragments, were investigated. It was found that the anisotropic response of the jointed specimens was governed by the micro-mechanism, such as crack initiation, propagation and coalescence, crack opening or closing, and frictional slip of cracks or joints. With the increase of joint continuity factor, the axial stress-axial strain curves change from single-peak to multipeak, the peak strength and Young’s modulus decrease. The specimens with medium joint inclination angle (30°,45° and 60°) has lower energy dissipation and strength due to stepped or shear failure, while specimens with small and large joint inclination angle (0°, 15°, 75° and 90°) has higher energy dissipation and strength due to axial cleavage or crushing failure.

Jan 1, 2015

By Bassam Kattaa

"Abstract - A heavy mineral survey of beach and dune sands including geochemical analysis for trace elements was undertaken to evaluate the economic potential of the sands and to understand the nature and distribution of the heavy minerals relative to potential source rocks. Results indicate that heavy minerals are generally derived from outcropping volcanic rocks that comprise a proportion of the hinterland in the south part of our survey area. The most abundant minerals are magnetite and pyroxene. The morphologies of the heavy mineral grains are angular to subangular, suggesting that they were transported short distances from the source rocks. Factors controlling heavy mineral distributions include wave and wind action, proximity to provenance, the fluvial drainage network, and longshore currrents.The most economically important mineral is ilmenite. Zircon and rutile concentrations are relatively minor and thus have lower economic potential."

Jan 1, 2002

By L. Boyd, A. Charland, G. Potts, D. Fragomeni, N. O. Lotter

"The Raglan orebody and concentrator has been the subject of study in Process Mineralogy at Falconbridge since 1998. (Lotter and Tuzun, 1998) The orebody is classified into three distinct textural groups, or end members. These are referred to as disseminated, net-textured, and Massive Sulphides, and differ in terms of mineral grain size, nickel grade, hardness, and mineral association. In this paper, it will be shown that the sampling and characterisation of each end member on an individual basis develops a higher-level understanding of the processing requirements and behaviour of the mixture of ore as presented to the mill.The end members have been used in robust prediction of recovery at various grind size p80 from laboratory scale High Confidence Flotation Tests. Weighted mean mixtures of the end members have been mathematically combined to determine impact of textural distribution on metallurgical performance as a function of grind size.The ore end members also vary in hardness and breakage mechanism and have been used to model throughput capability for existing, optimized and retrofit grinding circuits. This modeling has provided a range of expected throughputs as the relative proportions of each end member varies.Finally, the differing grinding requirement per end member has led to the development of grinding and flotation strategy that increases rougher flotation recovery and provides flowsheet options for a concentrator expansion. This leads to further understanding of the plant performance as a function of ore mixture."

Jan 1, 2005

By R. A. McIvor, R. S. Rafuse

"INCO Limited purchased a custom designed mobile hoist rope winder/tensioner in 1988 from TimberLand Equipment Limited to handle Large hoist ropes and serve as an emergency hoist. This paper describes the operation of the winder/tensioner and some of the different applications that the machine has been used to handle large loads.IntroductionINCO Limited operates 24 mine hoists in the Ontario Division and has approximately 50 miles of mine hoist rope hanging in the shaft plus an equal amount on spare reels. The mine hoist ropes range in size from )( inch to 2.305 inches in diameter with the majority being 1 3/4 inches and above. Prior to the procurement of a new high powered winder/tensioner in 1988, the mine hoist ropes were handled with a variety of methods and equipment using hydraulic or pneumatic powered reel winders. The largest such reel winder has a pull rating of 8000 Ibs and travels approximately 40 ft/min. Head ropes for the tower mounted friction hoists were installed and removed using a magazine on the hoist drum to wind and unwind the rope because the loads were greater than the capacity of the existing machinery. It was recognized that a large high capacity machine would improve the productivity for handling the larger hoist ropes and a feasibility study was undertaken to determine the parameters for such a machine."

Jan 1, 1995

By W. W. Muir

"The Baker Mine used a 100-ton per day conventional cyanide leach mill located in northern British Columbia. A production decision was made in early 1980 and the mill was on fine in April 1981.Ore reserves had been estimated at 100,000 Ions averaging 0.9 oz gold per ton and 18 oz silver per ton . Mineralization consists of electrum (Au/Ag) and acanthite (Ag2S).This paper will review plant design and focus on some problems associated with start-up and early operation with the intention of assisting other mine operators by indicating potential problem areas.IntroductionThis paper will discuss operating strategies employed at Baker which improved over-all mill performance. Also included are some ideas which could be steps toward a more efficient operation in a similar setting.Actual dore production by mine life was 37,606 oz gold and 742,117 oz silver.Figure 1 illustrates the relative stability attained over the mine life. Metal recoveries for gold and silver were 92% and 85% respectively.Safety at Baker was of prime importance because of its remote location. Baker received the Mine Safety Association ""Small Mines Award "" in two of its three operating years. At shutdown in late 1983 the mill had operated for over 850 days without a lost-time accident."

Jan 1, 1985

By B. T. Lu, J. L. Luo, H. X. Guo

This paper investigated the synergistic effect in the slurry-erosion process of carbon steel. In line with the mechanisms of material loss, the synergism due to interaction of erosion and corrosion was divided into the corrosion enhanced by erosion and erosion enhanced by corrosion. The erosion-corrosion tests were conducted with A1045 steel in slurries containing silica sand. Experimental results showed that the rotating of the sample in corrosive media raised both OCP and corrosion rate, but the impingement of solid particles did not affect the corrosion current significantly. In the quiescent solutions, the Faraday's law gave a good prediction for the weight loss caused by corrosion but for rotating samples, the weight loss experimentally measured was virtually greater than that predicted by the Faraday's law, indicating that the corrosion-enhanced erosion could occur in corrosive fluids in absence of solid particles. A half-logarithm relationship was observed between the weight loss due to corrosion-enhanced erosion and the anodic current density.

Jan 1, 2004

By H. Ito, T. Takasu

A leaching process for recycling small car motor scraps dismantled from End- of - Life -Vehicles (ELV) was investigated using waste pickling acid in steel work. Steel parts of mortar scraps were leached by waste pickling acid and Cu wire was recovered as pure Cu in the process. Pickling acid solution after leaching could be recycled in an ordinary process for waste pickling acid solution. High grade FeSO4 agent could be produced using H2SO4 as a pickling solution.

Jan 1, 2004

By Amin Jafari

Macrosegregation has always been an important issue with the solidification processes, particularly in Direct-Chill Casting of Aluminum alloys, where uneven properties, surface and bulk defects and limitations in productivity can be arisen due to macrosegregation in the cast product. Following the global attempts to practically predict the macrosegregation, in the present work, a numerical model was developed based on an industrial scale DC casting process to simulate the solidification and macrosegregation in an Al-4.5%Cu billet. Interesting aspects of this investigation are concerned with an efficient numerical scheme to keep simplicity, consistency and desired physical resolution of the solidification phenomena together. In the mathematical model, coupled conservation equations of mass, momentum, energy and species were solved numerically using finite volume method. A different numerical scheme, called SIMTLE, was introduced to link the energy and species equations with the phase diagram of the alloy. Calculations were performed on an industrial case and obtained results were compared to available experimental data to assure the performance of the model. Different macrosegregation features were predicted and discussed on the solidifying Al-alloy billet.

Oct 1, 2011

By Victor Maksaev, Marcos Zentilli

"Abstract - The Domeyko Cordillera, the westernmost uplifted crustal block of the composite High Andes of northern Chile (20°S to 28°S) hosts a narrow N-S trending belt of Late Eocene-Oligocene giant porphyry copper deposits, which include Collahuasi, Chuquicamata, El Abra, La Escondida, and El Salvador. These deposits are spatially and genetically associated with the closing igneous activity along this range, prior to a 30 km eastward jump of the magmatic front in response to tectonic plate interaction. The porphyry copper deposits are also spatially associated with a major intraarc strike-slip shear system, the Domeyko Fault System. Although the tectonic uplift of the 3000 m to 5000 m high range has generally been assumed to be mostly Miocene in age, field relationships suggest that the Domeyko Fault System and tectonic uplift were active as early as the Eocene, coinciding with porphyry copper emplacement between 41 Ma and 30 Ma. Apatite fission track (FT) thermochronology provides both age data and a time-temperature history for rocks since they cooled below a temperature of ca. 125°C (equivalent to a depth of 4 km to 5 km under normal geothermal gradients) on their way to the surface during exhumation, or after a heating event. Apatite FT data from the Paleozoic crystalline basement of the Domeyko Cordillera indicate that at least 4 km to 5 km of rocks were eroded during exhumation of this tectonic block between ca. 50 Ma to 30 Ma (Middle Eocene to Early Oligocene), a time that immediately precedes and overlaps with the emplacement of giant porphyry copper deposits. The FT data constrain the age and duration of a period of crustal thickening and extensive erosion known as the Incaic compression, an event recognized in the Andes of Chile and Peru. Assuming that cooling was due to denudation alone, modelling of the FT data allow estimation of denudation rates between 200 and 100 m/My during this period. In contrast, exposures of pre-porphyry Paleocene intrusives on the western edge of the Domeyko Cordillera reveal apatite FT ages that are concordant with biotite 40Ar-39Ar dates, indicating shallow emplacement, fast cooling and negligible exhumation. The apatite FT ages of the Chuquicamata and El Abra porphyry copper deposits are only marginally younger than their 40Ar-39Ar dates, implying fast cooling/exhumation of shallow mineralizing systems (ca. 2 km to 3 km). Their FT time-temperature history is compatible with extremely low rates of exhumation (ca. 50 m/My) since about 30 Ma (Early Oligocene). This limited extent of erosion, due to exceptional aridity, has greatly contributed to the preservation of rich supergene enriched blankets above some of the porphyry copper deposits.A model is proposed, which is consistent with field relationships, geochemical, and geochronological data. High relative velocities and intermediate-angle oblique convergence between the Nazca and South American plates in the Eocene-Early Oligocene led to intra-arc transpression partitioned into reverse faults of opposing vergence and a right-lateral shear system (the Domeyko Shear System) localized along the magmatic front. Crustal shortening and thickening led to uplift within the Domeyko Fault System and to erosion of at least 4 km to 5 km. Crustal thickening deepened the zone of magma generation, and magmas accumulated in the lower crust, allowing small volumes to rise rapidly to shallow levels along transtensional domains of the regional shear system. A similar model of crustal thickening and shortening before and during porphyry copper emplacement in zones of transtension may also apply to the Miocene-Pliocene giant porphyry copper province of central Chile."

Jan 1, 1999

By Sukumar Bandopadhyay, Arunapuram Sundararajan

"Unique production and environmental problems are associated with multiple seam mining where dragfines are used for overburden and interburden removal. On the production side, the problems are decreased dragfine efficiency in chopdown operations, the general need for spoil rehandle, complications in sequencing stripping and coal handling operations, and potential stability problems in highly stacked spoil. Many variations of dragline methods have been reported in the literature to encounter these problems. Because of the physical properties and peculiar hydrology of sub-arctic region mining of multiple seams in such areas probably could not be done with the methods used in temperate regions.The properties of thawed material would make spoil hard to place in a stable manner and thus would influence the mini sequence. For instance, multiple seam mining which requires some rehandling of spoil and prolonged exposure of overburden and interburden material might be precluded by the instability of thawed spoil and therefore mining techniques have to be modified. Since the deployment and operation of a dragline in modes different from conventional schemes will affect productivity, it will be necessary to study the effects on production of changing the dragfine operational schemes. This paper presents a heuristic simulation model of multi-seam dragline operation of a sub-arctic mine that can be used to analyze the handling of overburden and detailed study of the dragfine performance."

Jan 1, 1986

By Y. Wang

In this study, homogeneous (unseeded) precipitation of nesquehonite (MgCO3.3H20) by the reaction of MgC12 with (NH4)2CO3 in supersaturated solutions at 30 °C was investigated. Factors which influence the precipitation of MgCO3.3H20, such as initial concentration, temperature, stirring speed, titration speed, equilibration time, have been studied. SEM images show that the initial concentration and titration speed have significant effect on nesquehonite's crystal morphology and particle size. In addition, stirring speed and equilibration time also have some influence on its properties. With the optimization of operating conditions, the crystals can grow up to a length of about 40µm and a width of 5µm, indicating good filtration properties. High purity nesquehonite obtained in this study was calcined to produce highly pure MgO at 800 °C as shown by XRD results. The novel process may be used to separate Mg and Li from high Mg/Li ratio brines in Qinghai, China.

Jan 1, 2007

By Carmen Mihaela Neculita

Sulfate-reducing passive bioreactors efficiently treat acid mine drainage (AMD) by increasing its pH and alkalinity and by removing metals as sulfide precipitates, in addition to hydroxides and carbonates. However, the new mining legislation sets discharge limits based on physicochemical parameters and on the non-toxicity of treated effluent as well. In this study, toxicity was assessed for effluent from 3.5 L column bioreactors filled with mixtures of natural organic carbon sources and operated at two different hydraulic retention times (HRTs) of 7.3 d and 10 d for the treatment of a highly contaminated AMD. Acute toxicity was observed for D. magna, and a toxicity identification evaluation (TIE) procedure was performed to identify potential toxicants. To help the interpretation of the toxicity results, metal partition in the effluent was also determined by filtration and ultrafiltration, while geochemical modeling was performed for metal speciation evaluation. The 10 d HRT effluent was nonacutely lethal for rainbow trout but acutely lethal for D. magna, whereas the 7.3 d HRT effluent was toxic for both organisms. The toxicity to D. magna was eliminated by 2 h of aeration for the 10 d HRT effluent, and the TIE procedure suggested iron as a cause of toxicity. However, the 2 h aeration eliminated the toxicity of the 7.3 d HRT effluent, only if performed after the pH rising to 9.3. Data regarding metal speciation indicated instability of both effluents during aeration and were consistent with the toxicity being caused by iron. The study indicates that design of passive treatment should include sufficient HRT and posttreatment aeration to meet acute toxicity requirements. Keywords: acid mine drainage, sulphate-reducing passive bioreactors, hydraulic retention time, effluent toxicity, metal speciation

Nov 1, 2008

By Md. Rashedul Islam

Magnetic data was collected from the Yeoju historical sites using the fluxgate gradiometer through six sites & several grids. We measured the vertical gradient by the FM256 Fluxgate gradiometer. The readings were logged every half meter. The obtained data were processed and treated to introduce a high quality magnetic image. The gradiometer results defined various positive and negative magnetic anomalies, which revealed the existence of several archaeological features of different shapes and sizes. The study of the process magnetic images give us a concept that the subsurface features are caved shape stone chamber tombs, burial mounds, deep room structure, Yeoju mausoleum, pagoda?s square foundation stones, walls etc. All these are superior work of early Goguryeo inheriting orthodox Silla style. So, the study area may have great archeological interest.

May 1, 2009

By L. Bichler, A. Siebert-Timmer

In this research, novel YSZ ceramics doped with 5 mol% Nd2O3 were manufactured via Spark Plasma Sintering (SPS) process. The sintered Nd2O3-YSZ ceramics were subjected to a static supercritical water environment at a temperature and pressure of 400 °C and 31 MPa, respectively. The weight loss and microstructure development of the sintered ceramic before and after exposure to supercritical water was studied. The results suggested that Nd2O3 addition significantly improved the degradation resistance of the YSZ ceramics. This was attributed to the improved phase stability of the 5 mol% Nd2O3-YSZ ceramics, since X-ray Diffraction (XRD) studies showed that the cubic stabilized matrix in these ceramics was retained after exposure to supercritical water. In comparison, pure YSZ ceramics exhibited a rapid degradation behavior as well as a phase change.

Jan 1, 2014

By Virginia T. McLemore

The Gallinas Mountains are in northern Lincoln County and southern Torrance County, New Mexico, USA where a series of alkaline igneous bodies, including porphyritic latite, trachyte/syenite, andesite, and rhyolite laccoliths, flows, dikes, and plugs, have intruded Permian sedimentary rocks belonging to the Permian Abo, Yeso, and Glorieta Formations. A small amount of bastnaesite, a REE mineral, was recovered during processing for fluorite from the Gallinas Mountains. Four types of deposits are found in the Gallinas Mountains: epithermal REE-F veins, Cu-REE-F veins, REE-F breccia pipes and iron skarn deposits; all are associated with Tertiary alkaline to alkalic-calcic igneous rocks. Alteration includes brecciation, silicification, chloritization, and fenitization. District zonation is defined by Cu-REE-F (±Pb, Zn, Ag) veins that form center of the district, surrounded by REE-F veins. Carbonatites are inferred at depth by the presence of fenitization, carbonatization of the breccias, presence of REE and similarity of the intrusive rocks and mineralization to areas with known carbonatites.

May 1, 2011

By Christian Brits, Bob Blain, Lloyd Buckingham, Juliu Stieger, Jean-Francoi Dupont

Barrick Gold Corporation (Barrick) has undertaken innovative methods of evaluating and improving the performance of grinding mills in several of its operations around the world. The results have been positive with some of the mines showing more than 20% net energy improvement leading to more than 43,000 tonnes per year reduction in CO2 emissions in four of the operations reviewed.

Jan 1, 2012

By S. Forgeron

Presentation ? Introduction ? Canadian Underground Coal Mines ? Standardization of Geological Assessment ? Geomechanics Base-line Studies of Canadian Coal Mines ? Cape Breton Development Corporation Prince Mine ? Quinsam Coal Corporation ? 2 North and 4 South Mines ? Smoky River Coal Corporation 5B-4 Mine ? Conclusions and Baseline Comparison ? Figures

May 1, 2001

By Michel Dagbert

"In their paper, Marcotte and Boucher (2001) cast some new light on the old problem of 2D estimation of vein-type deposits with thickness and grade of intercepts. Using a theoretical approach, some extensive simulation experiments and the Walker Lake data, they show that the direct approach (interpolation of grade at points on a regular grid) gives better estimates of the true grade at those points than the indirect approach (interpolation of grade x thickness or accumulation and interpolation of thickness) when there is some positive correlation between grade and thickness and that this better performance increases with the correlation of grade and thickness as well as the variability of both variables.We would like to bring some reservations to that conclusion by showing that even if direct point grade estimates are better than indirect ones, it is not necessarily true for block estimates and in particular for the estimated grade of the whole orebody itself."

Jan 1, 2001