Search Documents

By R. N. Murarka

"Hydrocyclone modelling and selection procedure is illustrated. Computerized procedure for hydrocyclone cut size determination for grinding and non-grinding applications is described.A standard procedure for evaluating operating hydrocyclones is described in detail. Many case studies are illustrated comparing actual plant performance with the computer simulation output in terms of overflow product size distributions.INTRODUCTION Cyclones are widely used for applications such as: close circuit grinding, backfill, tailings and dewatering. Normally, cyclones are used for very fine separations where screens are not suitable or too expensive. Figure 1 shows the separation size range of various classifying devices. Cyclones are popular because of their low capital and operating cost. Cyclone selection procedure for different applications depends on the amount of information available on the cyclone feed slurry characteristics. Closed circuit grinding applications will be discussed in detail in this paper. The Cut Size:The size of the material in the feed which reports 50% to each product stream (i.e. underflow and overflow), after correcting for the feed solids by-passing with the underflow liquid, is termed the cut size or ""d50c"". This is often used as the criterion and the basis for cyclone design.When the corrected recovery to underflow of each mesh size in the feed is plotted against the geometric mean size in microns on a log scale, the micron size corresponding to 50% recovery is the d50c size."

Jan 1, 1992

By H. W. Smith, D. Guerin

"This paper describes the development of a dynamic model for a full- scale (64 tonnes/hr) grinding circuit consisting of an open-circuit rod mill feeding a ball mill operating in closed circuit. The object of constructing such a model is to investigate the static and dynamic behaviour of potential control schemes. Model selection, data processing and parameter estimation are discussed, and static and dynamic results of simulations are presented. Conclusions are drawn with regard to the adequacy of the model for such studies, and likely limitations on control of such circuits.IntroductionThe model developed here is intended to represent the grinding behaviour of the grinding circuit at the Lake Dufault division of Falconbridge Copper Mines Ltd. This circuit has been fully described elsewhere. At the time of the work described, the ball mill discharge was fed to a four-cell flotation bank , the tailings of which are combined with the rod mill discharge in the cyclone feed pump sump. As the emphasis in this study is on grinding behaviour, and as only I per cent of cyclone feed material is removed in these cells, no attempt has been made to include flotation behaviour in the simulation. One effect of the presence of flotation cells in the grinding circuit is, however, to necessitate somewhat finer grinding than might otherwise be needed: this will have effects on mill parameters.The paper is organized as follows. First the selection of models is discussed, paying particular attention to the problem of selecting simple, yet adequate, flow models for the mills. Then data gathering is described. The method of deriving mill model parameters is explained, and the results presented. Mass balancing of cyclone data and the determination of cyclone model parameters are described. The linking of the models into a full simulation is outlined, and sta tic and dynamic results presented. Finally, the results are discussed and conclusions drawn ."

Jan 1, 1980

By M. H. Allan

"This paper presents the geographic and geological setting of Saskatchewan Power Corporation's Poplar River Mine in south-central Saskatchewan, about 8 miles from the U.S. border. Generally the mine, which is being expanded to four million tons per year, is in an extremely disturbed geological area with severe dewatering problems. The lignite coal, which is strip mined, is supplied directly to an electric power generating station by means of a 7-mile unit-train private railroad.A number of unique reclamation and socio-economic problems were encountered because of the proximity to the U.S. border and because of the lack of experience of the regulatory authorities in projects of this kind. These are described in some detail, as well as the performance of one of the largest draglines in Canada. IntroductionThe Saskatchewan Power Corporation is a publicly owned utility which has the franchise to supply electricity and natural gas to all customers within the boundaries of Saskatchewan.Saskatchewan is a province which can almost be divided in two: the populated southern portion, principally devoted to farming, and the northern portion which is mostly on the Precambrian Shield and consists of lakes, rocks and muskeg. This portion is largely uninhabited except for a number of small villages. However, in the last few years there has been considerable mineral exploration and development, notably for uranium. This has helped considerably in the diversification of the basic agricultural economy of the province.Saskatchewan consists of 251,700 square miles, 761 miles north to south and an average of 335 miles east to west. It has a population of approximately 960,000, giving a population density of four persons per square mile. The Saskatchewan Power Corporation supplies 357,249 electrical arid 221,378 natural gas customers."

Jan 1, 1982

By G. Vibert Douglas

It often happens that the field geologist encounters a fault in ground where there is little to guide him with regard to the throw, or vertical displacement, and the heave, or horizontal displacement. The following construction gives both of these components of the fault, and the writers hope that it may prove a help to others. The construction is applicable to both normal and reversed faults. Briefly the procedure is as follows: Take a point which is common to the faulted geological feature and to the fault plane and on the downthrow side of the fault. Move this point in the horizontal plane in the direction indicated by the fault striæ. Rebat the point down to the plane of the fault and obtain its throw. Next consider the other side of the fault and truncate it down by the amount of the throw just determined. Then project the line of the geological feature through to the trace of the fault-plane at the lower horizon. The result is the relative positions of the two parts of the original geological feature as severed by the fault. In Figure r, let us consider a typical normal fault, that is, a fault in which the hanging-wall has gone down relative to the footwall. This characteristic, or its alternative, the reversed fault, is determined by observation on the ground. Let AB be the line of any geological feature such as the edge of a dyke, vein, or bedded sediment. The plane of which AB is the trace may have any dip; in the present case let us say 70° right. Let FF be the trace of a fault-plane which may have any dip; let us say 35° left in this case.

Jan 1, 1928

By Lian-Jin Tao

With fast development of China modernization, road construction obtains great achievement. However, in the construction process of highway, especially the high-grade highway in mountainous area, there are many unavoidable high cut slopes. Specifications for Design of Highway Subgrades, China, prescribe that the design scheme of slope with height more than 30m should be compared with bridge scheme and tunnel scheme economically. In spite of the existing guidelines, it is still quite common to see many high slopes due to engineering geological conditions, highway line shape, cost and issues related to traditional design ideas. Actually the traditional way with ?high backfill, the high cut? for mountainous highways seriously damages the original ecological environment and groundwater system, especially to those area with weak ecology, where the damage is unrecoverable. It is quite common practice to use artificial vegetation for cut slope virescence, however it still has problems such as low ratio of survivor, high maintenance cost and lack of species diversity. Now people are more and more aware of the importance of ecological environment, it becomes urgent to decrease the damage to ecological environment after ensuring the stability of high slopes. With the aim to reduce ecological damage, we proposed a new design approach which is ecological environment friendly by decreasing cut slope height with steep excavation scheme. This approach requires that (1) the geological condition is good, and the rockmass can be sTable itself; (2) excavation should not badly damage the rock, which means blasting must be controled by using buffer blasting, smooth blasting and pre-splitting blasting; (3) if local geological condition is not very good, excavation should have intervals for one bench, the advised space is 20m; (4) to ensure the slope stability in construction process, the cut slope should be reinforced more strongly than usual and in time. Finally, the deformation of the slope and the working condition of the reinforcement structure should be monitored to ensure the slope stability. The new design is used to a roadside cut slope of provincial trunk highway S223 in Guangdong Province. Based on intensive geological investigation and borehole tests, it is found that the slope rock mass is intact and sound, and the rock strength is quite high. Results from numerical modeling by UDEC reveal that compared with the traditional design scheme with 90.23m high slope, the steep scheme with only 23.46m high is characterized by its relatively large deformation and stress concentration, however the influenced area only appears at the upper slope and tends to sTable. With cable reinforcement, the stability of slope excavated steeply can be guaranteed. Deformation of the slope and the cable force are monitored in details in the period of construction, which show that the deformation of the slope decreases gradually and the final deformation is very small, and the cable tensions change small after the cables were tensioned. It is optimistically estimated that the steep slope should be sTable during operation. Comparison analysis between the steep scheme and the common scheme affirms that the steep excavation is better than the traditional scheme in terms of ecological environmental effect, slope height, the excavated amount, the excavated quantity of slope surface, engineering cost. It is concluded that if geological condition permits, the steep cut scheme should be used with better benefits.

May 1, 2009

By J. Budac, R. Kofluk, S. Mankasingh

Stainless steels such as 316L or 304 are normally relatively resistant to attack by nitric acid. However research at Sherritt International’s Fort Saskatchewan Operation reveals that when the stainless steel is immersed in an aqueous system in which nitric acid is used to dissolve metals such as cobalt or nickel, the steel can be seriously corroded. Sherritt is patenting a simple process for arresting the corrosion via the use of copper. This process is expected to substantially eliminate corrosion in processes where nitric acid is used to dissolve metals attached to a stainless steel substrate.

Jan 1, 2014

By Masaharu Moteki

At present, the Unmanned Construction System (UCS) is adapted on initial operation against the disaster. For instance, it has been used in Unzen. When the scale of the disaster is big, or the danger to a person is big, the UCS is expected as a quick and safe construction technology. The Remote Controlled UCS is introduced into construction site to repair earth-fill embankment or to remove rock, as urgent measures after the disaster outbreak. For improvement of the operability, shortening of the skill time, reduction of the fatigue, examination of the most suitable system (placement of a monitor and the joy stick) of the remote system is a main theme in the Public Works Research Institute (PWRI). In the report of this year, when the operator controls construction machine directly or he controls it using remote system (he can check the situation of site only via monitor), the degree of achievement, construction efficiency and construction precision were inspected. The remote system which is based on the system used at Unzen was developed at PWRI.

Aug 1, 2013

By A. David MacPhail

"Highland Valley Copper is a large volume producer of copper and molybdenum concentrates. Production is by conventional truck and shovel operation combined with an extensive ore handling in-pit crushing and conveying system.Grade of the two orebodies is low at 0.4% copper and 0.007% molybdenum and this demands a production rate in excess of 260 000 tpd at a stripping ratio of 1: 1. Mining cost has to be kept at minimum levels to keep the mine profitable and thus, it is necessary to keep in the forefront: of technology. As well as the in-pit crushing system, the mine has pioneered the use of shovel weighing coupled with a state-of-the-art dispatch system.Maintenance of the equipment is carried out at the on-site mine maintenance shop with assistance from local shops for engine and wheel motor rebuilds and other large jobs such as those requiring stress relieving. Shovel and truck rebuilds are undertaken by mine crews. Both long- and short-term planning is designed and scheduled in the mine engineering section. Outside consultants are used to assist in slope design, reclamation and blasting technology."

Jan 1, 1992

By H. Soto, J. Jara, F. Nava

A method has been developed to recover cyanide and copper from cyanidation effluents contaminated with thiocyanate and copper-cyanide complexes. Copper is precipitated as copper thiocyanate or as copper cyanide depending on pH and the concentrations of thiocyanate and cyanide present in the effluent. The copper precipitate presents good dewatering characteristics and can be easily separated from the effluent by thickening and filtration. The solution containing the bulk of the cyanide is then oxidized with ozone to transform the remaining thiocyanate into cyanide. This results in a regenerated solution rich in free cyanide that can be recycled to the cyanidation process. Careful control of the pH of the solution is required. First pH of the effluent is lowered to optimize the precipitation and oxidation stages, then the pH is restored to an alkaline value to regenerate the cyanide solution. Recoveries of over 96% copper are obtained. Free cyanide in the regenerated solution corresponds to up to 160% of the total cyanide contained in the original impure effluent. (The balance being accounted for by the cyanide obtained by the oxidation of thiocyanate). The efficiency of the thiocyanate oxidation stage is 85% to 90%. The method has been demonstrated at bench scale with effluents of various cyanidation plants of northern Quebec. A preliminary economic evaluation indicates that the procedure would be profitable for effluents rich in copper and thiocyanate. This is the case for most barren bleeds of Merrill Crowe and heap leaching operations and also certain CIP tailings of gold ores containing copper impurities. Environmentally the procedure is a better alternative than the current detoxification methods based on the oxidation of cyanide that do not allow for copper recovery and that have difficulties in producing a final effluent with acceptable levels of contaminants such as ammonia, thiocyanate and copper.

Jan 1, 1996

By E. M. De Souza

"The mining industry has developed a strong need for monitoring underground openings since bulk mining, used for increased productivity, has become the dominant mining method industry wide. The large stopes associated with bulk mining methods generally have to remain open and stable for several months, and monitoring is essential to provide an indication of ground response to mining and stope stability. The instrumentation data is also important during design optimization, which is used to maximize recovery, to minimize the dilution of ore and to minimize costs. Monitoring is essential to implement safety and is also critical in stope and mining sequence designs. The safety related aspects of monitoring include the protection of underground workers and the prevention of accidents by providing early warnings of the onset of any ground instability. The design related aspects of monitoring involve the development of data bases used for stope dimensioning and mine sequencing and timing and the monitoring of ground behaviour as a result of mining to verify the validity of the design thus allowing for remedial action during operation.Manual instrumentation data collection is, in a number of cases, economically unfeasible and, in many situations, dangerous as instrumented areas become inaccessible or extremely unstable. Also, because more and more complex instrumentation is being installed in underground operations, in several cases it becomes practically impossible to collect readings manually. The design and development of low-cost acquisition systems for mine wide monitoring would thus constitute an important step toward automation in excavation instrumentation. A unique menu-driven automatic 32-channel analog data acquisition and analysis system with a built-in rock failure warning mechanism has been designed and developed. This low cost acquisition system is capable of receiving, processing, displaying and storing the transmitted instrument data remotely and automatically. Computer software has been designed to provide data reduction and analysis immediately in the field and to automatically display results in graphical form for quick interpretation. Automatic data interpretation is used to show trends in rock mass behaviour and the system can be used to provide early warning of rock failure to the mine personnel working in there so that immediate remedial action can be safely taken."

Jan 1, 1992

By L. Cheng, Y. W. Pan, Y. R. Liu

"Impounding deformation of slope and foundation is significant during and post dam construction. Reservoir impoundment is accompanied with various phenomena, including material degradation, effective stress decreasing and buoyancy in rock masses. These phenomena are related with some engineering concerns like reservoir-induced earthquake, landslide and dam stability. The Malpasset dam and Vajont dam are typical hydraulic projects suffering from seepage in dam foundation and slope, which finally led to failure and landslide. Pore pressure in jointed rock masses is considered in constitutive relation. The expression of effective stress for porous rock with fluids is incorporated into the Drucker-Prager criterion. Based on monitoring data of valley width and dam deformation, the effective stress law is applied to analyse the impounding influence of slope and foundation to Jinping-I high arch dam. The dam is accompanied with complicated topographical and geological conditions. The results show that calculated and monitored values agree well, and the application of effective stress law provides an approach to evaluate dam deformation, stress and stability with impounding effect considered.INTRODUCTIONImpounding deformation of slope and foundation is a common and significant problem during dam construction and operation. This phenomenon exists in a lot of reservoirs in China, like Laxiwa, Ertan, Xiluodu and Jinping-I arch dams, and some dams in Europe. It is related with some engineering concerns like reservoir-induced earthquake, landslide and dam stability. The Malpasset dam and Vajont dam are typical hydraulic projects suffering from seepage in dam foundation and slope. Monitored data indicates that the valley width tends to shrink in hydraulic engineering during the impounding process, which will change the stress and deformation of dam and abutment. Therefore, global stability of dam and foundation should be evaluated with impounding process taken into consideration."

Jan 1, 2015

By J. Kramer, T. Hartmann

In the Hydrometallurgical processes, the presence of the so-called “crud” is a constant challenge in solvent extraction. Crud is a stable emulsion which forms along the interface between the aqueous and organic phase. The spread is influenced by the following parameters: first, wind blows the dust and impurities into the open sedimentation tanks. Second, the undissolved solids such as sand transported in the PLS causing problems in conjunction with incorrect agitator design. The crud fraction can decisively impact the efficiency of the hydrometallurgical extraction because the phase interface can constitute a large fraction and the sedimentation tanks cannot react flexibly to it. In the downstream process of the seriesconnected sedimentation tanks, they are thus all contaminated with crud. At the same time, the necessary mass transport is significantly impeded at the phase boundary between organic phase and aqueous phase due to the crud formation. The transfer of the organic phase into the electrolysis cell can result in a “burnout” of the cathode. The carry-over of this electrolyte into the extraction can cause problems with the pH regulation. The carry-over of the organic components into the raffinate also leads to contamination of the leaching circuit. The continuous treatment of the crud with a 3-phase decanter centrifuge is extremely effective in combating this problem. This technology splits all three phases from each other and they are consequently continuously separated. All subsequent process steps exhibit a stable, uniform effectiveness. The main advantage for the customer is that fluctuations in the process are eliminated and the organic phase can be recirculated back to the extraction. The recycling of the solvent alone justifies the investment in less than 6 months as examples from South Africa and Chile show. To operate solvent recovery in daily operation fully automated online at the optimum limit, the decanter centrifuge is equipped with a concentration-dependent pond adjustment called DControl®. By this means, we can guarantee our customers the maximum possible solvent recovery and minimise the solvent costs in this process step. This system is presented in detail in this paper.

Jan 1, 2012

By A. Dahi Taleghani, A. Shojaei

Continuum damage mechanics (CDM) of rocks is studied together with their elastic and plastic behaviors to develop simulation tools for hydraulic fracturing jobs in naturally fractured formations. The model is constituted based upon pressure sensitive inelastic deformation of porous rocks and their damage mechanisms in the cases of drained and undrained conditions. The CDM model is formulated within Fracture mechanics framework. The performance of the developed elastoplastic and CDM models are compared with the available test data of a specific shale play. The hydraulic fractures growth in the reservoir scale is then simulated; in which the effect of fluid viscosity, natural fractures characteristics and differential stresses on induced fracture network is studied. The simulation results are compared with the available solutions in the literature. The developed CDM model outperforms the traditional fracture mechanics approaches by removing stress singularities at the fracture tips and simulation of progressive fractures without any essential need for remeshing.

Jan 1, 2015

By H. T. John

"The objective of this paper is to demonstrate how the optimum cut -off grade can be calculated for typical large tonnage openpit mines. In the examples, it is assumed that the concentrator tonnage is fixed and that there are no market restrictions. The mining rate is assumed to be variable. This is usually the situation at an operating property.ModellingA model of the ore body is required to examine alternate cutoff grade strategies. The model must be accurate in its relationship between grade and tonnage. Table I shows a typical relationship between ore tons and grade for various cut-off grades. The average strip ratio is also shown. For higher cutoff grades, the ore tonnage is decreased and the ore grade is increased. Strip ratio increases with the cut-off grade.Using the relationship between ton s and grade, and assuming a homogenous, long life orebody, a simple calculation of the optimum cut-o ff grade can be made. The objective is to maximize the present value of cash flows. For the long life homogenous orebody example this objective is satisfied by maximizing present cash flows.Cash flow is calculated by subtracting operating cost from revenue . Operating cost will increase with the cut -off grade as the strip ratio increases."

Jan 1, 1985

By K. Yoshida

Recently, light magnesium alloy with superior heat radiating ability has been attracting attention in various fields. However cold plastic working of the alloy is very difficult and hot working necessary. Furthermore, the magnesium of products with complicated shapes is difficult, the processing cost is high, and the applicability of the alloy is limited. In this study, a technique for obtaining fine wires and tubes by cold drawing is examined to obtain wires and tubes with high strength, quality and surface morphology, while decreasing production cost. In addition, the shearing strain of magnesium alloy wires and tubes drawn under various drawing conditions was calculated by FEM analysis. It was clarified that cold drawing of magnesium alloy is possible. It was also demonstrated that greater reduction of the cross-sectional area could be realized during cold wire and tube drawing by optimizing the drawing conditions.

Jan 1, 2006

By Magdy Ibrahim

Detailed as-built project schedules are necessary to close out construction projects, benchmarking, forecasting, dispute resolution, and improving cost estimates of future projects. Manual procedures for developments of as-built documentation is time consuming, involves numerous interfaces and human interventions. This paper presents computational framework that encompasses automated site data acquisition and generates schedule updates utilizing commercially available project scheduling software. The work is carried out collaboratively with a Hydro Quebec team. The site data is captured employing mobile computing using iPad® type computers and Wi-Fi. The information is directly compiled in a centralized database server. The synchronization tool is a bi-directional application and is used on servers to communicate with iPad® computers deployed onsite. The captured data is stored in Microsoft SQL® relation database that consists of 63 entities. Computer software application has been developed in Microsoft Visual Basic® (vb.net) environment for extracting the collected site data, linking the database to the as planned schedule, and generating the actual, also known as as-built schedule. The development can be utilized in automated progress reporting, evaluating future bids, generating master schedules and a wide range of efficient EVM applications.

Aug 1, 2013

By Robert Voisey, Robert J. Spencer

"LynnGold's MacLellan Mine is located about 8 km south east of Lynn Lake immediately to the east of the Keewatin River (Fig. I). The property is accessible by an all-weather road, leading north from the provincial highway 391, which links with the Town of Leaf Rapids and the City of Thompson to the south.The ore body, as outlined in the original feasibility study, is expected to produce in excess of 9.3 x IQ6 gm of gold and silver over the next 5 years. However, the deposit is open to depth and exploration is continuing on and around the main zone and the many satellite deposits.The start of construction of the MacLellan Mine and mill was scheduled to phase in with the closure of the Fox copper-zinc mine located 48 km west of Lynn Lake. The majority of the employees from the Fox Operation were either employed at the MacLellan Mine or relocated to Sherrin's Ruttan Operation.GeologyThe MacLellan gold ore deposit is located on the northern section of the Lynn Lake Greenstone Belt known as the Rainbow Trend. This Trend is a 40 km gold bearing rock sequence extending both east and west from the MacLellan Mine. The southern section of these two east-west trending structures is known as the Johnson Shear, this is also gold bearing."

Jan 1, 1990

By M. Morin

"This paper examines the design issues associated with the integration of mineral processing within underground mining using a total systems approach. It demonstrates conceptual integrated system design options appropriate to a range of geological scenarios. Particular reference is then given to a case study of stoping in narrow base metal veins.The performance of such integrated systems in terms of productivity, economical and environmental criteria is demonstrated by means of simulation. Particular attention is given to the potential benefits to mine waste management. Processing technologies appear to offer genuine potential benefits, while underground mining methods may need to evolve further to facilitate full integration. This paper is based on industry supported research aimed at developing selective and clean underground mining systems. IntroductionTotal systems thinking is simple in principle but complex to implement. The premise is that to achieve optimum effectiveness and efficiency from a system, the complete system must be considered. Using this approach will avoid the situation where the optimization of a localized component of any system results in a negative impact on the performance of the complete system. Take for example the parts manager who reduces inventory costs without consideration of the consequences to the plant. If the plant goes down and a part is unavailable, it would then cost significantly more than the cost of having it in inventory (Ackoff, 1994).A tool for applying total systems thinking toward understanding and analyzing different mineral extraction options is the structured analysis and design techniques (SADT). Originally developed by Ross (1977), SADT is a formal systems engineering methodology (FIPS PUB, 1993) for process and enterprise modelling (Marca and McGowan, 1993). Figure 1 presents a highlevel structured analysis of the traditional or conventional metal extraction process. There are three sequential processes with several arrows entering or exiting each process. In SADT, inputs always enter from the left-hand side and exit as outputs of the process on the right-hand side. Constraints affecting the transformation of inputs to outputs enter the process from the top while resources or mechanisms enabling the transformation enter from the bottom. SADT is a hierarchical decomposition technique and further analysis is undertaken by expanding downward into each process."

Jan 1, 2003

By T. Yalcin

"This paper describes the development of a process flowsheet designed to provide high dewatering rates and to bring about savings in tailing disposal costs. The flowsheet comprises a hydrocyclone, a settling cone and a thickener arranged in closed circuit. The mill tailing, after pulp density adjustment, is fed to the hydrocyclone which yields two products. The underflow product is sent to the settling cone for further dewatering. The overflow product, together with the settling cone overflow, goes to the thickener which, with the aid of flocculants, gives a clear effluent and a relatively dilute underflow. The latter combines with the original mill tailing to form the hydrocyclone feed. Solids finally leave the system in the settling cone underflow which can reach pulp densities of up to 78%, making it suitable for direct disposal or for use as mine backfill.Some discussion is included for the selection and sizing of equipment required for this process. INTRODUCTIONDewatering is an essential process for the disposal of mill tailings which forms an added burden in milling practice, often with little or no return. It is, therefore, desirable to conduct this process as economically as possible. One way of reducing costs would be to increase the rate of dewatering so that savings can be made in the size of dewatering unit s which would lead to lower capital and operating expenditures.A common method of dewatering mill tailings is gravity sedimentation which is frequently carried out with the aid of flocculation. In most cases, flocculation greatly enhances the sedimentation process, but only until a pulp density of 50% to 55% is reached in the settled material.Centrifugal sedimentation in hydrocyclones can provide high pulp densities rapidly, but does not result in a clear effluent.This paper outlines a suitable combination of gravity and centrifugal sedimentations that results in an over-all high rate of dewatering. The system developed produces a material of high pulp density while at the same time giving clear effluent."

Jan 1, 1989

By Bill Parnell

"Friction winders and double drum winders have been used in the vertical shaft mining industry for over 100 years. In that time, there have been many changes made in the electronic and mechanical fields of hoisting, but few changes made in the manufacturing and performance of steel wire rope, until recently.In the past ten years, with the advent of high polymer thermoplastics, the industry has seen some major advancements in steel wire rope. By incorporating a polymer with steel, improvement of rope life and reduction of costly maintenance downtime has been accomplished.IntroductionThe Williams Mine is Canada's largest gold producer with an annual production of some 500 000 ounces of gold from 2.2 million tonnes of ore. The Williams Mine is situated in the Hemlo area of northwestern Ontario, approximately 40 Ian east of the town of Marathon. It is operated by the Williams Operating Corporation which is owned equally by Teck Corporation and Homestake Canada Inc. It is one of three adjacent properties forming the Hemlo gold camp."

Jan 1, 1995