Search Documents

By V. K. Gupta

"Effect of mill speed on grinding kinetics has been investigated with a view to using mill speed as a manipulated variable for control and optimization of the grinding circuit performance under variable ore hardness conditions. Dry and wet batch grinding tests were carried out for quartz, limestone and cement clinker in a 29 cm x 18 cm laboratory ball mill. Mill speed values selected were 55 and 70% critical. In the case of dry grinding operation, with an exception of quartz, for all materials studied the effect of mill speed on grinding rate was found to be insignificant for sizes finer than about 35 mesh. In the case of wet operation, grinding rates were found to be approximately proportional to the mill speed. The implications of these results are discussed.INTRODUCTIONIt is well known that mill speed has a considerable effect on the grinding rate of the ore particles l-3 For particles of a given size there is an optimum speed at which mill grinding efficiency is maximum (i.e. specific energy consumption is minimum) 3•4. Mill speed can, therefore, be effectively used as a manipulated variable to deal with the disturbances arising from changes in the size and hardness (grinding rate) of the ore being fed to the grinding circuit. Though, it has not been the case so far, with recent developments of ring motors2 and frequency inverters5 a continuous variation of mill speed has now become feasible, and it is expected that mill speed control will soon be a regular feature of plant operation2,6."

Jan 1, 1985

By Young Hyun Paik, Hyung Sup Choi, Yeun Sik Kim

The basic studies on the surface properties and flotation characteristics of ilmenite were made by electrophoretic, adsorption, contact-angle and floatability measurements. The isoelectric point of ilmenite is found to be at pH 5.6. By combining the results of electrokinetic studies and adsorption measurements, a clearer picture of the ilmenite-solution interface was observed. These findings were correlated with the floatability of ilmenite obtained by Hallimond tube tests. The general flotation characteristics of ilmenite are compared with those obtained for magnetite and rutile. It is indicated that the above three minerals, namely, ilmenite, magnetite and rutile, have very similar surface properties and flotation characteristics. Therefore, it is difficult to make an effective separation of these minerals by flotation. However, it is found that sodium orthophosphate acts as a selective depressant for magnetite in anionic flotation. Therefore, close pH control of the pulp in the presence of the phosphate ion enhances the possibility for a successful separation of these minerals.

Jan 1, 1967

By David Dreisinger

Arsenic occurs in nature in association with many valuable metals including copper, nickel, cobalt, gold and platinum group metals. The recovery of these valuable metals is of course complicated by the need to extract and stabilize arsenic in a form suitable for disposal. In this paper, a review of some recent developments related to hydrometallurgical treatment of arsenic bearing materials is provided. The key aspects of metal dissolution, arsenic stabilization and disposal are discussed.

Jan 1, 2014

By H. Y. Sun, Q. Y. Tan, X. P. Niu, L. Li, Y. Jia, R. M. Ruan

During bioleaching processes of sulfide minerals, the sulfide minerals act as the natural habitats for acidophiles, of which, most are autotrophic iron and sulfur oxidizing microbes. These microbes acquire energy by oxidation of sulfide minerals, and play crucial role in bioleaching processes. In the industrial bioleaching heaps, microbial community and their activity are highly related to engineering configurations, while the optimized industrial operation can help to fast dissolution of aim minerals and acid/iron balance under optimized microbial condition. Microbial community succession and activity formation, the function of microbes to mineral dissolution, the mechanisms to promotion and inhibition of sulfide minerals oxidation, and the industrial instances for microbial community regulation were reviewed. For these instances, promoted microbial activity helped to fast pyrite oxidation for sulfuric acid generation, which realized zero sulfur acid addition to the irrigation solution in the initiation of a bioleaching heaps. High microbial activity by optimized operation parameters improved Cu leaching efficiency during the heap bioleaching process. And also by inhibition of microbial activity, especially the iron oxidizing microbes, the excessive pyrite oxidation can be inhibited, which helped to the acid/iron balance during heap bioleaching. INTRODUCTION Around the world, high grade copper ore are exploited, while barely new high-grade deposits are succeeded, the copper grade of ore deposit is constantly decreasing. The increasing copper demands worldwide requests to process these low-grade ore deposits. Processing of low-grade ores are not economical by usual extraction processes. Heap leaching is a cheaper process for recovery of low-grade ores, and has been applied to extract valuable metals from sulfide minerals worldwide, such as copper, gold, uranium and nickel (Gericke et al., 2009). Heap leaching process has greatly decreased the economic grade and expanded the recoverable ore reserve worldwide (Brierley, 2008). It is usually carried out in the open environments, and could process huge amount of ore (usually in millions of tonnes in one reactor) in the heap reactor (Gericke et al., 2009). For copper sulfide, especially the secondary copper sulfides, heap (dump) bioleaching is successfully applied. Heap bioleaching process is cost saving, and sometimes can be achieved without adding chemical into heaps, by microbial fixing of the atmospheric N2 and CO2, and generating oxidant Fe3+ and sulfuric acid in heaps from oxidation of sulfide minerals. Also heap bioleaching is environment friendly by cycling use of the leaching solution, and without exhaust emission.

Jan 1, 2019

By X. G. Zhao, M. Cai, L. K. Ma, P. F. Li

"Crack initiation stress is one of the characteristic stress thresholds in the rock deformation process under compression. By analyzing AE responses of brittle rocks in uniaxial compression, a new method which is called cumulative AE hit (CAEH) method is proposed for determining the crack initiation stress. An advantage of the CAEH method is that the method removes the user's subjective judgment. To verify the CAEH method, uniaxial compression tests with AE measurement using 77 crystalline rock specimens were conducted. The test specimens cover eight rock classes with different mineral grain distributions. Crack initiation stresses of these specimens were determined by the proposed CAEH method and the LSR method, and the resulting mean crack initiation stresses determined using the two methods were comparable. In addition, taking one rock class with 20 specimens for example, the mean crack initiation stresses determined using the CAEH method and those from several established strain-based and AE-based methods were similar. Hence, the CAEH method can be used as an alternative method for crack initiation stress determination.INTRODUCTIONExperimental observations indicate that the failure process of brittle rocks is associated with crack initiation, crack propagation, crack damage and final strain localization (Brace et al., 1966; Bieniawski, 1967; Lockner, 1993; Wawersik & Fairhurst, 1970). Compression tests on cylindrical specimen are often used to characterize the crack development process. The crack initiation stress (sci), crack damage stress (scd), and peak stress (sc) represent important stress thresholds during the failure process of brittle rocks. Among the three characteristic stress magnitudes, sci is difficult to be determined objectively, directly from examining the stress–strain curves. Some researchers argued that sci obtained from laboratory compression tests is an important parameter for estimating the spalling failure observed in brittle rocks around underground excavations (Andersson et al., 2009; Diederichs, 2007; Martin, 1997). sci can also be used to estimate rock tensile strength and Hoek-Brown failure criterion parameter mi (Cai, 2010). Over the last 40 years, various strain-based methods have been proposed to determine the crack initiation stress in compression tests (Brace et al., 1966; Diederichs, 2007; Eberhardt et al., 1998; Lajtai, 1974; Martin & Chandler, 1994; Stacey, 1981). Nicksiar and Martin (2012) proposed a Lateral Strain Response (LSR) method for establishing sci for low-porosity rocks. Meanwhile, they also used different strain-based methods to evaluate sci of Äspö diorite, and the results showed that all strain-based methods gave acceptable crack initiation stress values. Subsequently, they utilized the LSR method to further investigate the crack initiation stresses in igneous, metamorphic, and sedimentary rocks in compression tests (Nicksiar & Martin, 2013). Compared with previously proposed strain-based methods, an advantage of the LSR method is that it removes the user judgment when interpreting sci. However, the use of the LSR method relies on accurate determination of scd and on having a polynomial fitting equation to find the maximum LSR value."

Jan 1, 2015

By I. Bakry

Uncertainty is an inherent characteristic of construction projects. Neglecting uncertainties associated with different input parameters in the planning stage could well lead to misleading and/or unachievable project schedules. The objective of this paper is to present a new approach towards scheduling repetitive construction projects while accounting for uncertainty. The paper presents an algorithm that quantifies anticipated delays resulting from different sources of uncertainty in the form of fuzzy time buffers. Through inserting the time buffers in strategic places in a time schedule, the algorithm provides protection against those main anticipated delays. The presented algorithm comprises two integrated components, a scheduling component responsible for producing a basic Linear Scheduling Method (LSM) schedule with deterministic activity durations, and a buffer component that handles fuzzy buffers sizing and insertion. The presented algorithm offers four different buffer insertion techniques covering different cases of interrelations between successive activities. The algorithm is implemented in a spreadsheet application, which automates calculations, yet allows users to fine tune the algorithm to fit the project at hand. With a focuses on highway construction projects as an example of repetitive construction projects, this paper accounts for sources of uncertainty such as weather, site conditions, change orders and equipment related delays. A hypothetical case is studied and explained to further demonstrate how the proposed algorithm works.

Aug 1, 2013

By Rachel S. Prudhomme, Michael L. Jeremic

"The consolidation of mine backfill by free zing is a concept which has been under study in the mining engineering laboratories at Laurentian University during the past three years. The proposed underground application of freezing involves the artificial freezing of in-situ backfill by means of a refrigerated brine solution which would be circulated through a circuit off freeze pipes. The most interesting findings to date are: (I) The uniaxial compressive strength off frozen fill is considerably higher than that of cemented fill in a ratio of 20:1 (aggregate to cement), and (2) load deformation characteristics of the frozen fill suggest that a higher ice content results in more brittle failure and that samples which have initially failed can still support up 10 one-half the ultimate load without additional failure.Although at this early stage a derailed economic analysis of the procedure has not been possible, a general evaluation of the costs involved suggests that the method could be competitive with the hydraulic placement of cemented backfill. Results obtained from laboratory investigations indicate that the freezing of backfill is a structurally feasible option .IntroductionGround consolidation by freezing is based on the principle of transformation o f water contained in an aggregate-slurry into ice, which act s as a binding agent between the bulk particles, and which results in the transformation of a granular soil into a ""rock -type"" material. The abrasive nature of the particles enhance s the strength o f the ice by providing internal friction. As a result of this internal friction, the chances of plastic flow of the frozen mass when in a loaded condition are reduced(1). T he strength of a frozen aggregate is al so dependent on the grain shape of the aggregate particles which may or may not promote particle interlocking(2) and on the temperature since, below the freezing point of the water/aggregate mixture, the strength of the frozen mass increase s with decreasing temperatures.In the shaft sinking industry, artificial freezing of loose , unconsolidated soils has been in practice for several decades. Shafts for Saskatchewan 's potash industry have been sun k to depths of 3000 feet by employing artificial freezing to stabilize the Blairmore Formation(3). The common procedure for freezing ground for shaft sinking is summarized as follows(4,5): I) 150 mm diameter bore holes spaced on 1.5 m centres are drilled in a circular pattern with a radius of 1.5 m outside the periphery of the proposed shaft."

Jan 1, 1985

By John A. Meech

"Oleic acid flotation of Mount Wright thickener underflow tailing material has been shown to be capable of increasing plant recovery by 3%. High levels of oleic acid addition (1.5 kg/t) are required, which limit the economic practicality of the system at this time. Nevertheless, from a technical viewpoint, the process is stable with respect to extreme fluctuations in oleic acid requirements, pulp pH and pulp temperature. Methods to reduce the average consumption of oleic acid need to be found. One technique that merits further testwork uses the ""piggy-back"" principle to float hematite fines with coarsegrained hematite particles.IntroductionWith most large-scale iron mining operations treating specular hematite ores, flotation is not often conside red a necessary processing step. The bulk of the iron minerals can be concentrated by gravity techniques and the generation of fines can be minimized because of the course- grained nature of the mineralization. Nevertheless, production of some fine material is unavoidable, and recovery of iron from this fraction by spirals is poor (10-30%).When the proportion of the iron in these fines becomes excessive, alternative methods to conventional spirals are considered(11), Many of the techniques that have been developed suffer from either poor recovery (e.g. the Reichert cones at 36010 recovery)(11) or low throughput rates (e.g. wet highintensity magnetic separation)(12), Flotation is often passed over because of excessive reagent costs, pollution problems and/or balling difficulties from the reagents used.However, of all the processes available, flotation can yield high recoveries (60-90%) at reasonable throughput rates with excellent process control features (reagent addition and/or cell level). The key parameter is reagent cost.This paper describes testwork on the use of oleic acid to float hematite from the fine fractions of the Mount Wright concentrator tailing. The concentrate product from this plant is directly shipped, so no balling problems exist. As well, oleic acid may be considered a lesser pollution hazard than many of the cationic collectors used in other iron ore flotation systems. A reduction in fine hematite slimes discharged as tailing into lakes may also reduce environmental damage."

Jan 1, 1981

By Ike Isagon

Backfilling has become an integral process in underground mining operations, with varying cost-effective forms of application. This study is a part of an overall investigation into the backfill practices at Copper Cliff North Mine (CCNM). The mine is well-diversified in terms of backfill methodologies and practices. The mine employs different fill methods such as cemented and un-cemented rock fill, slag fill, and cemented hydraulic fill (or a combination of them) in order to fill the voids created by mining activities. The history of backfilling at CCNM has been dominated by cemented and un-cemented slag fill. Each fill method requires operating and engineering guidelines for a cost effective quality control system. The purpose of this paper is to briefly discuss the backfill methods and applications, operating guidelines, and engineering requirements at CCNM.

May 1, 2011

By M. Xiao Bo

In recent years, there has been a heightened interest in the hydrometallurgical processing of sulfide ores and concentrates (especially copper sulfide ores and concentrates) mostly in the USA and Chile. Currently, hydrometallurgical operations account for about 30% of the primary copper production. In the present research, the leaching phenomena of IOCG (iron-oxide hosted copper-gold) ores and concentrates were studied. The IOCG ore, which is characterized as having a predominant amount of magnetite with fine chalcopyrite, is currently the center of attention for new copper resources. Heap leaching of IOCG ore is desirable because of its low cost. However, the leaching characteristics of the ores and concentrates and the mechanisms of copper leaching require investigation. This study defines the factors, which affect the leaching operation, such as the ORP, pH and oxidizing agents. Based on these results, the optimal leaching conditions are provided for pilot column leaching test and ultimately, commercial operations.

Jan 1, 2007

By J. R. Levin, E. J. Schelter

"We present some of our recent efforts in the development of predictive, directed oxidation chemistry of cerium(III) complexes under non-aqueous conditions. The electrochemistry of cerium(III)- alkali metal heterobimetallic aryloxide complexes is reported and compared with cerium aryloxide complexes that are kinetically stabilized by hydrogen bonding cations that span between the complexed aryloxide ligands. Comparative electrochemical measurements reveal differences between the heterobimetallic complexes and the hydrogen-bonded complexes.INTRODUCTIONThe rare earth elements comprise the lanthanides, La–Lu, and the element yttrium (Aspinall, 2001). Rare earth ores such as monazite, LnPO4, and bastnäsite, LnFCO3, typically bear mixtures of light rare earths: La–Sm while monazite, LnPO4, contains mixtures of heavy rare earths (Eu–Lu) (Cotton, 2006). Pure rare earth elements typically are isolated using a liquid-liquid separations process.(Bautista, 1995) The hydrometallurgy of these elements is a difficult problem because the separation factors between neighboring rare earths, which are predicated on the small differences in the sizes of the trivalent ions, are quite small (Cox, 1992). The element cerium, with its 4f1 electronic configuration in the trivalent state, is unique among the rare earth elements due to a relatively accessible 4f0 electronic configuration. The accessibility of the 4f0 configuration underlies the chemistry of cerium(IV), the only rare earth ion with molecular chemistry in the tetravalent oxidation state (Cotton, 2006). Cerium is trivially separated from mixtures of light rare earths by making use of its unique oxidation chemistry. In an effort to extend separations chemistry by oxidation reactions to other rare earth elements such as terbium and praseodymium, the solution electrochemistry of well-defined cerium complexes is of interest."

Jan 1, 2012

By Z. Zhang, M. -Y. Liu, X. -G. Chen, F. Breton

"The microstructures of AlSi10Mg foundry alloy in permanent mould (PM) and high pressure vacuum die (HPVD) castings were analyzed and compared. The as-cast microstructures of two castings mainly consisted of eutectic silicon particles, primary Mg2Si and Fe-rich intermetallic phases. The surface layer in HPVD castings, which has a unique feature and different structures, was carefully characterized. The dimension variation of microstructural phases along the cross section in PM samples is less than that in HPVD samples, although the size of microstructural phases in PM samples was much larger than that in HPVD samples. The mechanical properties of PM and HPVD samples were evaluated on as-cast and T6-treated conditions. The tensile properties of HPVD castings are remarkable better than those of PM castings on the as-cast condition. The T6 heat treatment greatly improves the tensile strength of PM castings while it has limited impact on the tensile strength of HPVD castings.INTRODUCTION The AlSi10Mg alloys are widely applied to the high pressure die casting (HPD) and high pressure vacuum die casting (HPVD). In the HPD process, the melt is injected into the die cavity under a high speed (30–50 m/s in the gate velocity for aluminum alloys), and solidified under a high pressure (up to 200 MPa in the cavity) and with a high cooling rate (up to ~103 Ks–1) (Gourlay, Laukli & Dahle, 2007; Ji, Wang, Watson & Fan, 2013). This results in a unique microstructure feature that is different to other casting processes under gravity. One major concern in HPD castings is porosity due to trapped air in the cavity (Ji et al., 2013), which seriously restricts the application of a heat treatment on the improvement of mechanical prosperities because of the formation of blisters on casting surfaces. For the process improvement, the high pressure vacuum die casting was developed in 1980s (Uchida, 2009). In this process, the melt is injected into the die cavity under reduced pressure (vacuum), which greatly reduces gas porosity in castings due to effectively avoiding the trapped air. Consequently, HPVD castings are heat-treatable without the formation of blisters on castings surface during heat treatment. The HPVD process has been widely applied to produce high quality structural castings in recent years attributed to reliable vacuum system development (Uchida, 2009). However, the microstructure features of HPVD castings are not systemically characterized yet."

Jan 1, 2018

By T Salman

The construction and use of the B.E.T. (gas adsorption) apparatus is described. Examples are given for the determination of large and small surface areas using nitrogen and krypton. Introduction A NY study of the milling of ores from crushing to grinding, classification, and concentration and finally dewatering of the products involves solid particles which are either in contact with a gas or a liquid phase. The surface area of the solid and its characteristics constitute important parameters in all mineral dressing operations. The success of any particular operation is dependent on the interaction of the surface of the solid particles with the gas or the liquid phase. Particle size and specific surface (surface area per unit weight) continue to be important parameters in the flotation research associated with the adsorption of collector molecules or ions on mineral particles, as in the early years of mineral dressing research (1). In order to understand the mechanism of the flotation process, it is essential that the surface properties of the adsorbent be known.

Jan 1, 1965

By M. Carvalho

The primary motivation underlying the proposal of polygeneration systems for mine sites is to increase the efficient use of natural resources by combining different technologies and energy resources while satisfying energy service demands. For many mineral producers, particularly in Canada?s mining extremes of climate and depth, energy in support of mineral production can be the second largest cost centre after labour. A generic methodology is proposed for the design of energy supply systems in mine sites, based on a search for the minimum discounted cost of energy supplied for all feasible different plant configurations. These configurations can be represented within a connectivity matrix which corresponds to a network representation. A Mixed Integer Programming formulation is set out for the multiperiod synthesis and operational planning problem. This is characterized by i) binary variables for the selection of technologies, ii) integer variables for the determination of the number of units installed, and iii) by continuous variables for the representation of energy and economic flows. Through the integration of particular energy supply strategies matching specific mine circumstances (on-grid, remote, degree days, etc) and consideration of technologies that improve energy efficiency, hitherto not considered new technologies and demand management systems or new perspectives on optimal mine site energy supply can be investigated. Some of these investigations identify the economic conditions through which biomass energy feedstocks should be used, for direct heat production, for gasification and providing for Fischer-Tropsch syndiesel manufacture. As well as integrating demand from mobile diesel-fuelled plant into an optimization procedure that hitherto has only been considered for static energy production and consumption plant, this analysis shows how the techniques can be used to explore economic conditions of threshold prices for biomass (purpose-grown biomass and peat are considered herein) and trucked-in diesel. The methodology also allows for electricity and syngas storage and diesel and biomass bunkering. Within the paper the energy demands for a remote, open pit mining operation located in Northern Ontario are considered as a case study to illustrate the technique and investigations. As expected, for mines close to electricity, natural gas, and diesel distribution infrastructures, the optimal choice is to connect. When a constraint is applied specifying that connection is not possible, as would be for the case exemplified, the optimal choice includes some of the more exotic options for mine site energy supply.

Aug 1, 2013

By J. Dufour

Although the recovery of nitric and hydrofluoric acids from stainless steel pickle liquors has been solved by several methods, such as solvent extraction, acid retardation, evaporation or pyrohydrolysis, metals (mainly iron, chromium and nickel) are usually obtained as a waste or by-product that has to be disposed. Alternatively, the treatment requires a high liquor flow to be economical, as is the case for pyrohydrolysis. A new process has been developed for metals recovery, that produces metal oxides with a low fluoride content. This new technique is based on a selective precipitation mechanism, which produces nickel hydroxide with a purity of 90%, separate from a mixture of iron and chromium oxides and hydroxides suitable for recycling. The reaction mechanism is based on the precipitation of fluoride compounds of iron and chromium, K2FeF5 and CrF3. For this purpose, free fluoride must be added as potassium fluoride. Also, solid fluoride compounds are hydrolysed, releasing free fluoride. A part of the fluoride is recycled to the selective precipitation operation and the remainder is fed to the acid recovery stage. Nickel does not react in this operation; it remains in solution giving a high separation yield.

Jan 1, 2006

By Marty Hudyma

There are five independent seismic source parameters: seismic energy, seismic moment, source size, location, and time. These parameters are investigated primarily for evaluating seismic hazard and understanding seismic source mechanism(s). Broadly, seismic hazard is the likelihood of occurrence of an event of a given magnitude. Seismic source mechanism is the mode of rockmass failure that causes the seismic event. Most mine seismicity analysis techniques use a combination of a few of the independent source parameters. In literature, time is perhaps the least discussed and most underutilized of these five parameters. This paper discusses three applications of time to understand both seismic hazard and seismic source mechanism in mines. The first application is time history analyses, which focuses on how other parameters of interest vary over time. Examples are presented to show how time history analyses can give information about both seismic hazard and seismic source mechanism. The second application is analysis of time-between-events. This technique can give insight into seismic source mechanism. The final application is phasor analysis using the Schuster test. This method can be used to investigate how seismic source mechanisms may change over time. For both time-between-events analysis and phasor analysis, there are important implications with regards to scale dependence and the breakdown of self-similarity of mining-induced seismicity.

Jun 1, 2012

By Wynne Potter

"On the west coast of Cape Breton Island four coal basins have been identified, varying in age and extending from Port Hood northeasterly to Chimney Corner. Those of Chimney Corner - St. Rose in the north and Port Hood in the south belong to the Pennsylvanian Riversdale Group while lying between them are the coal basins of Mabou and Inverness belonging to the younger Pictou Group. Almost all of the coal basins are submarine and coal mining was carried out on all basins at various times. The seams in all basins dip steeply seaward at angles from 10 to 20 degrees but were found to flatten seaward. The coal is ranked as a high volatile C bituminous coal. Ash and sulphur contents are high compared with Sydney coal and the coal has a tendency to spontaneous combustion when stored in large quantities.Of the four basins, the most significant is that of Mabou. At Mabou recent seismic and drilling investigations have indicated that although a sizable reserve of coal may be found offshore the structural problems, particularly faults, and the poor quality of the coal encountered will make it a resource of the future, if at all. Inferred resources have been calculated at 150 million tonnes in four seams over a 10 km2 area and extending 3 km from shore. The quality of the Mabou coals varies with ash, ranging from 5 to 25 per cent and sulphur up to 6 per cent. Calorific value ranges from 25.3 Mj I kg to 31. 7 Mj I kg. The Port Hood and St. Rose -Chimney Corner fields (Fig. 1) contain 16 million and 3 million tonnes respectively, but the Inverness basin is considered to have been depleted. The active mine in this area is the Evans Mine at St. Rose that is currently producing between 30 -50,000 tonnes a year from proven reserves of approximately 3 million tonnes."

Jan 1, 1985

By M. Sutherland

"Increased efforts to improve mine safety have led to various successful forms of ground control in Canadian underground mines. At Inca Limited's T-3 Mine in Thompson, Manitoba, a perimeter blasting method has been implemented in jumbo drilled development headings.The technique utilizes an increased number of perimeter blast holes in the drill pattern while decreasing the linear charge density of explosives in any individual perimeter hole. The decrease in perimeter charge density means less blast damage to the surrounding structure.The benefits realized include increased safety through less loose ground and substantially less scaling time, less overbreak and improved long-term drift stability. This paper highlights the development and implementation of the perimeter blasting program.IntroductionThompson Mine Thompson Mine is a 6000 ton per day underground nickel mine located just outside the city of Thompson, 400 miles north of Winnipeg. The mine is serviced by the T-I shaft and by the T-3 shaft. The shafts are 10 000 ft apart and are connected on several levels with the deepest operating levels at T-1 and T-3 being 4000 ft and 2400 ft respectively.The T-3 Mine presently produces 52% of the total Thompson Mine production and 65070 of the 3000 ft of mine development each month. Current development of the 5 million ton 1, C orebody below 2400 level at T-3 will maintain these production and development ratios.Depending on equipment requirements, development headings at T-3 Mine vary in size. The 1, C ramp, at 17 1/2 ft wide by 10 1/2 ft high, is presently the largest development heading at T-3. Fifty- two per cent of the development footage is done with four Gardner Denver two boom electric /hydraulic jumbos and one Gardner Denver one boom electric /hydraulic jumbo. The remaining 48% is driven with hand-held jack-leg drills."

Jan 1, 1990

By David Whalen

Mobile equipment in oil sand mining operations experience more maintenance problems than similar equipment in other surface mines, due to soft underfoot conditions. Oil sand properties are known to vary with temperature, bitumen content and previous loading cycles. One of the challenges is the widely variable underfoot pressure which supports shovels and trucks. In the case of a heavy hauler driving on in-pit roads, each tire is supported by a different ground stiffness resulting in an apparent uneven surface. Driving over uneven ground causes twist in the truck frame, which is transmitted to the dump body. Through a finite element analysis of a haul truck dump body, it was shown that slight frame twists produce localized stresses in the intersections of the floor stiffeners. These stresses are at times greater than those resulting from the maximum ore weight and are primarily responsible for cracking in these intersections. Syncrude maintains high quality haul roads, which are constructed of gravel, and makes every effort to keep the shovel pit roads as smooth as possible. This problem cannot be avoided through operational practices only and must also be accounted for in the design of haul truck bodies.

May 1, 2003

By S. Yano, S. Takagi, Y. Nagaya, T. Akai, T. Ishida, Z. Bennour, T. Suzuki

"It is often reported that the concept of single-plane-fracture is not sufficient to account for the productivity from shale gas/oil wells. Many researchers introduce the concept of the stimulated reservoir volume to describe observed production behaviour. However, the characteristics of the stimulated reservoir volume are not well understood. In this study, to investigate the characteristics of fractures and surrounding region induced by the hydraulic fracturing, a devised hydraulic fracturing experiment was conducted using the cylindrical shale specimens in the laboratory.Two resins were prepared as the fracturing fluid for the experiments: cyanoacrylate, an instant glue, mixed with a fluorescent paint (resin A), and methyl metaacrylate, a thermosetting acrylic resin, mixed with a fluorescent paint (resin B). These resins were able to fix within the specimen after fracturing. This is because the present study aimed to only detect fractures induced by hydraulic fracturing. Cut sections of the specimens were observed under ultraviolet light irradiation. It is expected that the hydraulically induced fractures and the surrounding regions will be detected because the induced fractures filled with the resin should emit light, while the other parts will not.The specimens, which were collected from the Kushiro Coal Mine in Hokkaido, Japan at the depth around 275 m, were roughly 85 mm in diameter, 170 mm in length, and cored normal to the sedimentary planes. An injection hole with a 10-mm diameter was drilled onto the center of the specimen parallel to the sedimentary plane to simulate hydraulic fracturing in shale gas development. The experiment was conducted under a uniaxial loading condition of 3 MPa and the fracturing fluid was injected into the sealed injection hole at a constant flow rate using a syringe pump.After the fracturing experiment, the resins were fixed in the specimens and then the cut sections were observed under ultraviolet light irradiation. As a result, the hydraulically induced fractures, which were filled with the resin, are clearly observed. Detailed microscopic observations show that the main fractures are tortuous and are accompanied by many thinner ramified fractures. Additionally, fractured regions where the resin penetrates significantly are observed around the main fractures in the specimens fractured by the resin B. These induced fractures and fractured regions are considered to be the stimulated region in which permeability is improved. The necessity of estimation on the features of fracture tortuosity and ramified fractures is indicated for more accurate understanding of the well production and the stimulated reservoir volume."

Jan 1, 2015