Search Documents

By Donald Leroux, Ralph Dahlke, Dave Scott, Finch. James A., Cesar O. Gomez

"The efficiency of the flotation process depends on how effectively air is dispersed into small bubbles. Bubble surface area flux - the surface area of bubbles per unit time per unit cross-section area of a cell - is emerging as the parameter to characterize gas dispersion. One of the approaches proposed to measure bubble surface area flux in industrial cells is based on the measurement of two variables: gas velocity and gas holdup, using separate sensors. Plant testing of the gas velocity sensor gave evidence of a series of operational problems which may be necessary to correct before attempting to characterize gas dispersion. Problems such as uneven air distribution within a cell and along a bank, faulty air and slurry valves detected during attempts to redistribute air, and poor control of pulp level and gas flow became evident. Detection of these problems from gas velocity measurements is illustrated.INTRODUCTIONBubble surface area flux is considered a key variable in the optimization of flotation circuit performance (Gorain et al., 1997; 1998). The Mineral Processing Group at McGill University has devised and developed a method for estimating bubble surface area flux in industrial flotation cells (Finch et al., 1999). The method is based on measuring gas holdup and superficial gas velocity using two separate sensors and applying drift flux analysis to estimate bubble size (Dobby et al., 1988; Banisi and Finch, 1994). With bubble size and superficial gas velocity known bubble surface area flux can be calculated.This method was selected by Noranda to characterize gas dispersion in cells as part of a program to model and optimize flotation circuit performance. However, initial testing at Brunswick Mine with the gas velocity sensor provided some unexpected results indicating operational problems and equipment malfunctions that needed to be addressed before systematic measurement of gas dispersion could be initiated.The subject of this communication is to illustrate the detection of these problems from gas velocity measurements. The line 3 Zn Cleaner circuit comprising four stages of Denver DR cells was the main subject of analysis, including the effect of correcting these problems on the metallurgical performance of the Zn 3rd cleaner bank of ten DRl 00 cells."

Jan 1, 2001

By D. F. Hambley

"In designing are passes f or underground mines specific consideration should be given to unimpaired flow of broken rock, the dump point, and typical practices f or overcoming operational difficulties. Design features such as branches, bends, and knuckles should also be considered. This paper pro vides engineering information and various criteria for designing are passes, draw points. feeders, and support systems, together with several illustrative examples.IntroductionOre passes are the primary mean s o f vertical transfer of mined ore to the ore bins and loading pocket from which the o re is hoisted to the surface (Fig. 1) . While the words "" ore"" and ""ore pass"" are used here, such transfer systems ca n be used for any broken rock.The most extensive ore pass systems are found in caving and sublevel stoping mines. Extensive ore pass systems are also found in multilevel mines having steeply dipping orebodies. In more flat-lying orebodies , ore pass systems are sometimes used in conjunction with conveyor systems .Two decades have passed since the principles of the flow of bulk solids were formulated (Jenike, 1961, 1964; Johanson and Colijn, 1964; Kvapil , 1965). However, few published papers are available that discuss the design criteria for ore pass systems. Therefore, the aim of this paper is to provide the information necessary for good o re pass design .Rock Flow in Ore Pass SystemsIf an ore pass system is to fulfill its function, the transfer o f material must occur in an orderly fashion and in such a way that the full size of the opening is employed effectively. Apart from un controlled flow at the drawpoint, or outlet , whose design will be considered later in this paper, two occurrences may impede flow in an ore pass, namely:• Hangups due to interlocking arches.• Hangups due to cohesive arches.Prevention of each of these problems will be discussed in succeeding sections of this paper. A third problem piping, is related to the ratio of the drawpoint size to the o re pass size and will be discussed under drawpoint de sign."

Jan 1, 1987

By K. Waters, A. Navarra, T. Grammatikopoulos

Strategic decisions to develop a mineral deposit are subject to geological uncertainty, due to the sparsity of drill core samples. The selection of metallurgical equipment is especially critical, since it restricts the processing options that are available to different ore blocks, even as the nature of the deposit is still highly uncertain. Current approaches for long-term mine planning are successful at addressing geological uncertainty, but do not adequately represent alternate modes of operation for the mineral processing plant, nor do they provide sufficient guidance for developing processing options. Nonetheless, recent developments in stochastic optimization and computer data structures have resulted in a framework that can integrate operational modes into strategic mine planning algorithms. A logical next step is to incorporate geometallurgical models that relate mineralogical features to plant performance, as described in this paper.

Jan 1, 2017

By A. Zorkovská, S. Castro, P. Baláž, Z. Bujnáková

Enargite (Cu3AsS4) belongs among refractory copper minerals with very low hydrometallurgical extractability of copper. An application of enargite leaching in acid solutions leads to simultaneous dissolution of copper and arsenic and the final leach solutions have to be treated for the separation of both elements. However, the alkaline leaching of enargite is selective. Arsenic passes into leach while produced copper sulphide represents the raw material suitable for pyrometallurgy. The hydrometallurgical processing of mineral can be influenced positively by mechanochemical route. We have shown that more than 80 % of arsenic can be extracted from enargite concentrate by atmospheric alkaline leaching at 95 °C when mechanical activation in an attritor is applied. The produced Cu2S can be further treated with elemental iron where mechanochemical intervention is applied in the second stage of enargite processing. The final product forms Cu/FeS nanocomposite from which copper nanoparticles can be easily separated. The illustrated concept of copper obtaining from copper sulphide is an example of so-called “dry” processing, as reactions in gas and liquid phases are excluded. This concept of environmentally friendly metallurgical processing can be classified as an impetus for novel technology to produce copper from enargite concentrates.

Jan 1, 2012

By R. J. Mitchell

"The use of hydraulically delivered classified tailings sands to provide ground support in large mining operations is still widespread despite recent developments of alternate backfilling methods and materials. The major disadvantages of the use of hydraulic fill are the costs and risks associated with slurry delivery. The main risk is that of bulkhead failure resulting from sand liquefaction due to insufficient operational control or due to dynamic loading from earthquake or rockburst. That risk may be eliminated by the pouring of a stiff cemented sand plug in the base of each stope prior to continuous fill pouring in that stope. An additional advantage of cemented plugs is that massive bulkheads are not needed. Instead, a temporary (removable and reusable) bulkhead can be used for plug forming.Physical model studies of fill pressures on a temporary bulkhead were carried out in a 3 m radius centrifuge facility. Fill pouring in-flight was carried out in order to model prototype stress paths. The results indicate that the average bulkhead pressure is likely to be less than 10 kPa under normal operating conditions and less than 20 kPa under the poorest anticipated operating conditions which include smooth walls, high slimes content and high water-content slurries. A portable bulkhead consisting of a central core and a surrounding sealing bladder was modelled and found to be effective. The use of different sizes of cores allowed the stress distribution adjacent to these bulkheads to be evaluated."

Jan 1, 1992

By H. M. Woodrooffe

IT IS WELL KNOWN that chrysotile asbestos from various occurrences exhibits varied physical properties and certain differences in chemical corn position, both of which conditions may have an important bearing on the industrial utilization of the fibre. The usefulness of a harsh fibre in the manufacture of asbestos cement products and of low-iron fibre for certain electrical uses are examples. It is also .possible to obtain a fibre with a texture too harsh and brittle to be of economic value. Much research into the structure of the mineral and to a lesser degree observations relating the water of combination to certain physical properties have ?been reported. This paper is an attempt to show that the pyrolysis of ?chrysotile takes place in three stages and that the conditions of pyrolysis are peculiar to the fibre and may afford some clue to the variations in physical properties of asbestos fibres which affect their utilization.

Jan 1, 1956

By L. J. Cunningham

Introduction The property of Rouyn Merger Gold Mines, Limited, is in Rouyn and Joannès townships, Western Quebec, seven miles east of the town of Rouyn. Traversing it is the east-west trending Cadillac-Bouzan fault. Diamond drilling in 1944 and 1945 along a shear zone south of the fault indicated an ore deposit lying at the contact between sedimentary and volcanic rocks and dipping approximately 60° to the northwest. In the summer of 1945 it was decided to sink a shaft to investigate the indicated ore zone. In the immediate vicinity of the deposit, bed-rock is overlain by clay beds, in some places as much as 70 feet thick. Consequently, possible shaft sites were limited to those locations where overburden would not be excessive. The most favourable site was about 125 feet to the south of the ore zone as projected vertically from bed-rock to the surface. Accordingly, it was decided to sink the shaft at this point, with an inclination of 60° N. W., paralleling the dip of the ore zone.

Jan 1, 1948

By T. A. Postolski, A. J. Sinclair

"Abstract - Where block (selective mining unit) grade distributions can be determined, the effect of average random errors of block grade estimates on metal recovery can be evaluated quantitatively. That is, for a given estimation error and cutoff grade, it is possible to calculate the quantity of metal that is lost as a result of misclassifying ore blocks as waste, as well as the dilution that ensues from misclassifying waste blocks as ore. Example calculations using a computer program GAINLOSS and realistic block grade distribution parameters for both a porphyry-type deposit and an epithermal gold deposit illustrate some fundamental relations that are important in quality control of estimation and in reconciliations concerning a comparison of ore estimates with production.Where the cutoff grade is on the lower tail of the grade distribution, metal arising from dilution can be much less than metal lost through misclassifying ore as waste. Hence, average grade of milled material could possibly be higher than expected (estimated) and tonnes milled will be smaller than estimated.Where the cutoff grade is on the higher tail of the grade distribution, tonnes arising from dilution will be greater than tonnes lost by misclassifying ore as waste. Thus, tonnage mined will be greater than estimated and the average grade milled will be less than estimated.The software GAINLOSS permits rapid comparison of the tonnes and average grade for all blocks selected as ore for a variety of levels of block estimation errors. These comparisons can be incorporated in a financial analysis to evaluate whether or not it is worthwhile to improve a high, average block estimation error to some lower value."

Jan 1, 1998

By P. Wells

"In the past decade, there have been many developments in processing of nickel/copper sulfide ores. Improved pentlandite/pyrrhotite flotation selectivity with the use of new reagents, fine regrinding and Redox measurement (control) has led to increased pyrrhotite rejection and thus higher concentrate grades. Flash flotation has increased overall nickel and associated precious group metal recoveries. Recovery of both fine and coarse particles has been improved through an understanding of flotation cell hydrodynamics. The separation of copper from nickel in such ores has seen a similar level of development. From the late 80s to very recently, the use of flotation columns, the use of pyrrhotite depressing reagents and the improved understanding of the complex mineralogy of chalcopyrite, pentlandite and pyrrhotite have considerably increased copper / nickel separation efficiency. Copper concentrate with more than 30% copper and less than 0.5% nickel grade is now obtainable at 80-85% copper recovery from mill feed compared to 70-75% copper recovery with 30% copper and 1% nickel grade only a few years ago. Improved copper / nickel separation in milling operations has the potential to substantially improve the processing of the resulting concentrates and thus the overall return from the extraction of nickel and copper from sulfide ores.INTRODUCTIONNickel metal by itself or in alloys with other metals and materials makes a significant contribution to modern society. The relatively high price that nickel commands compared to other base metals is a reflection of the fact that, although abundant in the universe, nickel is sparingly distributed in the earth’s crust. There are two types of nickel deposits that are currently being exploited: complex sulfide ores and lateritic oxide ores. Lateritic contain no copper but in sulfide deposits, nickel– bearing minerals, principally pentlandite (Pn, [Ni,Fe]8S9), some millerite (NiS) and violarite ([Ni,Fe]S) are often found in association with copper-bearing minerals, mainly chalcopyrite (Cp, CuFeS2) and cubanite (CuFe2S3). The copper content of such ores can vary considerably from as high as 5-8% (in some Sudbury basin ores) to as low as 0.1% (in ores mined by Western Mining at Mount Keith, Western Australia and by Inco in Thompson, Manitoba). The valuable minerals Pn and Cp are almost invariably found associated with pyrrhotite (Po, Fe7S8) which along with nonsulphide rock has to be rejected to tails in the primary milling stage. The bulk concentrate from the primary stage is then treated to depress Pn and float Cp. A complete Cu/Ni separation at the mill would be highly desirable but this is not possible because of locking between a small fraction of the valuable minerals. As a result, Cu/Ni separation has to be carried out both during milling and during refining of the matte following smelting. At Inco, Jinchuan and in Norilsk, a chalcocite / heazlewoodite separation is made by flotation following slow cooling of the matte. In the present Sudbury Inco operations, Cu/Ni separation has not been conducted at the mill since 1991 and all Cu/Ni separation takes place at the matte processing plant. Because of the rising ratio of Cu to Ni in the ore, this strategy is under review and this paper describes some recent studies of circuits in preparation for possible installation of a copper / nickel separation circuit at Inco’s Clarabelle Mill in the Sudbury area."

Jan 1, 2004

By L Munholand, G. Soucy, P. Quintal

This work presents early results from the first study to optimize the hydrodynamics of a Plasma Lift Reactor (PLR). The PLR is designed to break down organic contaminants in aqueous solutions. New experimental results are presented for air/water tests and for plasma degradation of organic contaminants in Bayer liquor. In addition, a multiphase Computational Fluid Dynamics (CFD) model has been developed which predicts the hydrodynamic behavior in the PLR. These results of this work suggest the PLR is effective at reducing contaminants in the Bayer liquor and that the CFD model adequately describes the hydrodynamic flow.

Jan 1, 2005

By Robert B. Parsons

"While it might seem like heresy to suggest that ""taxation"" can be a source of financing, never the less some generous tax rules can considerably enhance the tax savings pertaining to a particular expenditure or project. A basic tax knowledge, and careful tax planning, can optimize government participation in a project. INTRODUCTIONIn trying to identify sources of financing for a project, ""government"" as a source of funding is normally thought of in terms of government grants, loan guarantees, interest rate buy downs, property tax waivers, hydro subsidies, and so on. Generally, such concessions are somewhat difficult to obtain, especially in the current period of apparent fiscal restraint. One source of government funding which should not be overlooked is the income tax regime, and, at the provincial level, the various provincial mining tax regimes.While the taxpayer would not normally view a tax system as a potential source of government financing, nevertheless various federal and provincial rules applicable to the mining industry can offer attractive tax deductions - and tax savings - with respect to particular expenditures. In fact, it is not unusual for a civil servant to refer to a tax deduction as a tax ""subsidy"". For example, in the right circumstances, the cost of a smelter expansion in New Brunswick would cost the operator only 31 cents on the dollar, with the federal and provincial governments paying for the other 69 cents by foregoing tax revenues (Table I). In a sense, such tax savings could be compared to a government grant equal to 69% of project costs. Of course, not every project expenditure will generate that degree of government funding. The fact of the matter is that the percentages of tax savings attached to different expenditures cover a wide range, depending on a complex mix of factors. The point to understand is that the tax rules can offer some valuable savings, even after tax reform, and that a basic knowledge of the tax rules can yield some fruitful rewards."

Jan 1, 1989

By T. A. Postolski, A. J. Sinclair

"Abstract- Two examples are used to describe how geological features impact on the development of semi-variogram models to be used for geostatistical resource/reserve estimation of porphyry-type deposits. In the Main zone of the Huckleberry porphyry copper deposit, mineralization is concentrated in fracture zones localized in volcanic rocks, along the eastern and southern margins of a granitic stock. Mineralized volcanic rocks can be subdivided into three separate domains, each with its own preferred direction of mineralization that is reflected in contoured Cu diagrams and semivariograms.The East zone at Huckleberry deposit, spatially distinct from the Main zone, is controlled by a fracture zone elongate roughly east-westerly and bounded on the south by a major fault (easterly striking and steeply dipping) across which there is a dramatic drop in grades. The eastern part of the East zone appears to be coaxial with a large intrusive body; the western part contains a small, elongate dike-like intrusion. Contoured Cu values for many levels suggest that the principal direction of geological elongation of the east and west domains of the East zone differs significantly. Independently derived semi-variogram models for each domain are different and reflect this difference in trend.In both Main and East zones of the Huckleberry deposit, block estimates by ordinary kriging are significantly different using a domain-specific semi-variogram model than using a deposit-general semi-variogram model. The domain-specific estimates are deemed better because they are based on local controls of mineralization and have less conditional bias than those generated by the depositgeneral semi-variogram model."

Jan 1, 1998

By D. W. Ginsberg, D. Cieplinski

"The lifetime cost of a material handling system, or any mine system, can be reduced through the application of quality engineering. Dynamic simulation is a powerful tool that can be used to enhance the experience and ingenuity of the design team. It cannot only de-bottleneck the system to improve system productivity, but also define critical design criteria to eliminate over-design and reduce capital cost. Eliminating over-design also reduces operating costs by lowering component replacement costs and by ensuring all parts of the system operate at a higher utilization and efficiency. IntroductionA mine owner’s profitability is improved when a mine is developed at the lowest lifetime cost. This cost relates not only to capital and operating costs, but also, to a great extent, on the efficiency and reliability of the operation. These factors are tied directly to the quality of the engineering which depends on the experience of the engineers involved, and their ability to apply known system information in a rational and constructive manner.It is becoming apparent that it is increasingly more difficult to deliver the quality of engineering expected and needed to provide attractive lifetime costs using traditional design methods. Historically, system information has been evaluated based on a limited amount of information to which global rules-of-thumb and the engineer’s personal experience were applied to develop design criteria. However, market forces are dictating that more system parameters be defined and that they be defined more accurately so that the most economical system can be developed. This increase in the volume of information and the need for more accurate predictions is straining, if not already exceeding, the ability of engineers to apply simple global rules of- thumb and to combine all the information in a rational, comprehensive and representative set of design criteria. Furthermore, as proposed system production rates increase beyond established industry practice, the extrapolation of the engineer’s experience becomes more difficult and increases the risk in the proposed design."

Jan 1, 1998

By I. H. Warren

"An analysis of form-coking processes is presented in terms-of their fundamental mode of operation and their relationship to other coking processes. Their possible future role in cokemaking is assessed. IntroductionAny consideration of prospects and possibilities for form coking must commence with the iron and steel industries-their likely future growth pattern on a world and regional basis and the potential direction of future developments in iron and steelmaking technology.From the numerous estimates which have been made of the future consumption of steel, it would appear that a growth rate of 3lllo between now and the year 2000 is likely. Radical changes in steel making technology are unlikely to be commercially adopted on any significant scale during the next twenty years . However, widespread commercialization inter alia of continuous casting and direct reduction, growth of electric furnace steelmaking and a decrease in coke rates will all contribute to a growth rate for metallurgical coke that certainly will be less than that of steel."

Jan 1, 1980

By Jozef S. Stachula

"INCO Limited operates eleven under-ground mines in the Sudbury area. The mines are located on the rim of the Sudbury Basin, an oval with the axis in the range of 27 km and 60 km. The ore dips to at least 3000 m below surface. The ores are mined primarily for nickel and copper. Total ore production from underground is in excess of 55 000tonnes per day.Over 40 surface fans have been installed since the late 1960s. All of the fans are adjustable pitch, axial flow units. A major factor influencing ventilation design in the last 30years has been the introduction of diesel equipment underground. Volumes per fan have ranged from 60 m3/sec. to 330 m3/sec., with motors from 100 hp to 2500 hp.Fans of the axial flow type have been commonly used for main fan installations at Canadian mines for many years. The standard arrangement has been to mount these fans horizontally, i.e. with the fan shaft and the long axis of the housing horizontal. This is a natural arrangement for an underground fan, but for a surface installation, a vertically mounted fan has definite advantages.The surface area taken up by a typical vertical fan installation is generally about one quarter that of a horizontal fan of the same capacity (Rutherford, 1957). This is not a problem with isolated fans and fat surface out crop sites, but where the installation is to be near existing buildings, or where there are poor surface soil conditions, space and cost considerations greatly flavour vertical fans."

Jan 1, 1996

By D. Nikols, G. Caraghiaur, P. C. Roxburgh

"IntroductionThe Highvale Mine is located 70 km west of Edmonton , Alberta on the south side of Lake Wabamun. It has been developed by TransAlta Utilities Corporation as a captive mine to supply fuel to two genera ting power plant s. The mine is owned by TransAlta and operated under contract by Manalta Coal. Within the mine permit area, TransAlta own s the right to mine 80% of the recoverable surface mineable coal.The planning process starts with the annually produced 25-year energy forecast which is provided by the Electric Utility Planning Council (EUPC). A 1983 forecast predicts an average annual increase in energy requirements of 4% over the next 25 years. Put another way, the requirement will double before the end of the century. A lar ge part of the base load generation of the Province of Alberta is provided by th e plants fueled from Highvale Mine. The Highvale Mine is therefore expected to maintain a high output over a long period of time.Mine PlanningMine planning is an ongoing, interative process that draws from many sources. All levels of planning draw from the same sources but du e to the different processes and objectives of each planning class, the degree of influence may differ. The planner becomes then a coordinator bringing together data and excerpts from several disciplines in groups. Generally, there are four classes of mining plan s; these are all used at the Highvale Mine (Table I)."

Jan 1, 1986

By C. V. Deutsch, O. Babak, J. G. Manchuk

High levels of geological heterogeneity occurring over relatively short distances pose a challenge to the unconventional open-pit techniques used in oil sands mining. There is strong motivation to mine selectively and minimize dilution and loss; however, the large equipment and high mining rate used to meet production targets tend to reduce selectivity. A numerical model is developed to account for geological complexity, mining equipment, regulatory criteria, and other operational parameters. This framework is used for more accurate forecasts, optimization of equipment, and other operational decisions. An example demonstrates the approach in light of Alberta Energy Regulator criteria.

Jan 1, 2014

By Julian Baldry

"This paper begins by describing the parameters of high-speed underground tracked drifting operations and the mucking cycle, and-discusses their variations. The railbound Haggloader 8HR is then described, as well as the Hagglund shuttle trains, outlining the advantages and disadvantages of the system. A comparison with conventional mucking operations is then given.IntroductionDrift and tunnel rounds are mucked by one of two major methods, either trackless with diesel loaders and trucks or with track loaders and cars. The aim of this paper is to compare the conventional tracked mucking cycle with the Hagglunds system alternatives.For many years, the traditional method of attacking the mucking cycle has been with a rocker shovel loader, a string of cars and a locomotive. The rocker shovel loads the first car and when full it is taken to a side drift, cherry picker or some other transfer point and is exchanged for an empty one. This empty car is then pushed back into the face and the loading continues until all cars are full . Then the whole train is taken out to a dump point where the cars are emptied. Normally the train's capacity is less than the volume of the muckpile, so the cars go back to the face. This loading cycle is repeated until all muck is removed from the heading. The last train out from the heading usually takes the loader and parks it in a side drift before continuing on to the dump where the cars are emptied.This simplified version of the traditional loading cycle excludes the ancillary work elements such as track laying and so on, but does point out that the cars must be transferred when full and that the whole train normally makes at least two round trips from the dump to the face. The prime aim in drifting is to cycle a round whithin a working shift which necessitates that no one part absorbs so much time as to prevent the completion of the cycle.Mucking, drilling and loading and the ancillary work such as rock bolting, vent and service pipe hanging typically each take one-third of the available work time. Drilling or mucking can and often do, because of various factors, take nearly half of the total cycle time. Once any segment of the operation starts to take this portion of the shift, the likelihood of missed rounds becomes increasingly greater."

Jan 1, 1981

By G. P. Demopoulos

"The recovery and separation of platinum-group metals (PGM) from primary and secondary materials currently attracts a lot of interest due to the high value of the metals and their increasing demand for high-tech applications. Thus, the traditional refining processes are gradually replaced by newer more efficient separation techniques such as solvent extraction and ion exchange. In this paper the classical and modern refining techniques are reviewed and the pertinent solution chemistry dictating proper processing strategies in each case is discussed. The technological advantages of the modern separation methods are emphasized and reference to the recovery of PGM from primary as well as secondary materials is given. INTRODUCTIONDue to their outstanding physicochemical properties, such as catalytic activity, conductivity and corrosion/oxidation resistance, precious metals now find extensive usage outside of the traditional jewellery and investment industries. The increasing use of precious metals in such areas as electronics and catalysis, as well as their increasing high value, has led to a growing interest in their recovery and separation from primary and secondary materials.Quantitatively the demand of platinum metals in the western world by area of application is described in Table I. Platinum and palladium represent 90% of the total demand, Rh and Ru 8% and the remaining is taken by Ir and Os. In terms of value the following were the average prices (US$/oz) of the metals in the second half of 1986: 500 Pt, 125 Pd, 1200 Rh, 650 Os, 400 Ir and 80 Ru. Due to these prices, exploration, mining, reclamation and refining activity were very high in South Africa, the biggest producer of Pt metals in the world, as well as in other areas: United States (Stilwater deposit), Canada (Sudbury, Marathon and Lac des Isles, Ontario; Kenly Lake, Quebec, etc.), Australia, Europe and elsewhere"

Jan 1, 1989

"In the UK, Ireland, and Western Europe, the mineral resource and reserve reporting standard is the PERC Code, developed and maintained by the Pan-European Reserves and Resources Reporting Committee, which is a standing committee set up under the auspices of a number of professional organisations which include the Institute of Materials, Minerals and Mining (loM3), the Geological Society of London (GSL), the European Federation of Geologists (EFG) and the Institute of Geologists of Ireland (IGI) to develop a Pan-European reporting code. The PERC Code supercedes the old IMMM Reporting Code 2001 and is recognised by the UK securities regulators and stock exchanges.""FOREWORD1 The Pan European Reserves and Resources Reporting Committee (PERC) Code for Reporting of Exploration Results, Mineral Resources and Mineral Reserves (further referred to as 'the Code') sets out minimum standards, recommendations and guidelines for Public Reporting of Exploration Results, Mineral Resources and Mineral Reserves in the United Kingdom, Ireland and Europe. The history of development of this code is summarised in Appendix 4.This 2008 edition supersedes all previous editions of The Reporting Code and the IMM Reporting Code.INTRODUCTION2 In this edition of the PERC Code, important terms and their definitions are highlighted in bold text. The guidelines are placed after the respective Code clauses using indented italics. They are intended to provide assistance and guidance to users in interpreting the application of the clauses in the Code. The same indented italics typeface formatting has been applied to Table 1, and to Appendices 1 and 2 which form part of the Guidelines.3 The Code has been adopted by the Institute of Materials, Minerals and Mining (loM3), the Geological Society of London (GSL), the European Federation of Geologists (EFG) and the Institute of Geologists of Ireland (IGI), and is therefore binding on their individual members.Appendix 1 contains a table of generic terms and their equivalents, designed to avoid unnecessary duplication or ambiguity in the textAppendix 2 provides Rules of Conduct for Mineral Resource and Mineral Reserve estimators that should be considered in addition to the Codes of Ethics normally applying to members of professional institutions."

Jan 1, 2003