Search Documents

By R. J. McLeod

"Grinding at Giant Yellowknife is done in two stages. The first stage consists of two ball mills in closed circuit will: mechanical classifiers, the classifier overflow goes to flotation. The tailings from this flotation circuit are separated into slime and sand portions, the slimes go to an additional flotation circuit while the sand portion goes to the secondary grinding mills.Milltronic automatic sound control units were installed on each of the two primary ball mills and put into operation September 3, 1966. After about two months adjustments to the control units the operators were taken off the grinding circuit on November 1, 1966. The operators duties were taken over by the automatic control units while miscellaneous work was taken over by the helpers in the mill. The labour saving by the installation is approximately $2250.00 per month.After a short period of operation it was apparent there was a slight change in grind. The screen analysis of the primary classifier overflows for the period May to August 1966 averaged 62.23% minus 200 mesh while for the period September to December 1966 averaged 62.0% minus 200 mesh. This is a slight coarsening of the grind. The change in the primary grind has manifested itself also in the screen analysis of the final grind. Before automation the final grind was 80% minus 200 mesh, while after automation it was 7 5% minus 200 mesh. A change of grind was also noted in the flotation concentrates. Before automation the screen analysis of the concentrates was 35% plus 200 mesh and 50% minus 3 25 mesh. A ft er automation it was 35% plus 200 mesh and 47 .5% minus 325 mesh. In other words the grind got coarser or perhaps we should say there was less overgrinding. Another significant change took place in the assays of the slime and sand portion of the primary flotation tailings. It was usual under manual control for the slime portion to assay higher in gold than the sand portion. The reverse is now true."

Jan 1, 1967

By W. Petruk

A study was undertaken to determine whether interrelations between mineral grains affect ore breakage during grinding, and to establish a correlation between ore breakage and mineral liberation. A base metal ore from the Brunswick No. 12 deposit in New Brunswick was ground for different periods of time in a laboratory ball mill, and both the unbroken ore and the ground products were analysed by image analysis. The results show that the mode of breakage is strongly influenced by the behaviour of pyrite. Similar size distributions were obtained for material from the 15 minute grind in a laboratory ball mill, for the grinding circuit discharge from a commercial mill, and for pyrite grains in the unbroken ore. This similarity indicates that a 15 minute grind breaks poorly bonded pyrite grains along grain boundaries, and represents the limit of easy breakage for the ore. Such a grind liberates both large separate grains of ore minerals and poorly bonded mineral grains that occur in interstices among pyrite. On the other hand the 15 minute grind does not separate moderately bonded mineral grains nor release moderately bonded interstitial minerals from pyrite; a 45 minute grind in a laboratory ball mill is required. It is assumed that, for Brunswick No. 12 ore, a 45 minute grind in a laboratory ball mill is equivalent to regrinding in a commercial mill. Grinding beyond 45 minutes in a laboratory ball mill breaks the ore by fracturing pyrite across grain boundaries and by chipping grain edges. Such intense grinding does not markedly increase sphalerite liberation from Brunswick No. 12 ore, because most of the sphalerite that can be released was liberated at the 45 minute grind. In contrast the intense grinding increases galena liberation because a significant proportion of the galena occurs as minute inclusions in pyrite. These findings show that ore breakage and coincident liberation depend upon size distributions, intergrowths, and mode of occurrence of the minerals in an ore.

Jan 1, 1988

By T. Xue, A. Singhal, D. Wrana, I. Mihaylov

"At Vale's Thompson Nickel Refinery, the copper and arsenic in the nickel electrolyte are removed by precipitation using H2S, generating a sulphide precipitate containing about 40% Cu, 8% Ni, 2 to 4% As and 30% S. This residue has been typically stored in impoundment ponds within the plant site. Various options for reprocessing it have been investigated over the years. One of the options involved oxidative pressure acid leach, whereby over 95% Cu, Ni and As were extracted. More recently, an atmospheric alkaline sulphide leaching process for selective removal of 70 to 90% As was developed and mini-plant tested. After alkaline sulphide leaching, the dissolved arsenic is precipitated as stable basic ferric arsenate (BFA) with the addition of ferric sulfate, while the low-arsenic Cu/Ni sulfide is suitable for processing in Vale's operations elsewhere in Canada.INTRODUCTIONVale’s Thompson Nickel Refinery was commissioned in 1961 and currently it has the capacity to produce about 56,700 tonnes per year of electrolytic nickel as cathode slab and rounds products. A sulphate and chloride mixed electrolyte is used in the Thompson refining process and it typically contains 75 to 85 g/L Ni, 50 to 60 g/L Cl, 90 to 120 g/L SO4 2-, 25 to 30 g/L Na and 8 to 9 g/L boric acid. The main impurities in the Thompson anolyte are copper, cobalt, arsenic, iron and lead.The simplified Thompson electrolyte purification flowsheet is shown in Figure 1 (Oliver & Wrana, 2009, Goble & Chapman, 1986); it consists of precipitation of copper, arsenic and lead with H2S, followed by nickel replenishment with ground matte and acid and removal of cobalt and iron with Cl2 and NiCO3."

Jan 1, 2012

By G. F. Raymond, W. P. Armstrong

"At the time of this study, the Valley mine was producing 23 000 tonnes of ore per day from a large, low-grade porphyry copper orebody. Sulphide mineralization, principally bornite and chalcopyrite, occurs in a stock work of quartz veins in one phase of the Guichon Creek batholith. The property was explored from 1967 to 1982, and was placed in production in 1983.Using a three-parameter lognormal approximation developed by G.F. Raymond at Similkam een and Mount Isa Mines, a geo- statistical conditional probability ore reserve was estimated prior to mining. Comparisons with blasthole kriging and milled ore for the first 17 months of production showed close agreements at all cut-offs between conditional probability estimates and mineable ore. This was not true of either kriging or polygon estimates. An important part of this work was identifying and correcting for bias in both exploration and blasthole samples.IntroductionCominco's Valley lake deposit is a large, low-grade, porphyry copper orebody in the Highland Valley of British Columbia. Total indicated plus inferred ore reserves are 700 M tonnes at ore grade of 0.47070 Cu. At the time of writing, ore milling is at a rate of 23 000 tI d through the old Bethlehem mill. Mining is in 10m horizontal benches using 9.8 m3 shovels and 90 tonne trucks. Since this paper was written, Valley and nearby Lomex have been combined into Highland Valley Copper with a combined oreproduction of about 120 000 tI d.Copper mineralization, principally bornite and chalcopyrite, is regularly distributed throughout the deposit as disseminated low-grade within a granodiorite host rock, and as higher grade veinlets within a stock work of near-vertical quartz veins generally 10 cm or less in width. It is likely that problems with sample variability and sample bias are mainly related to mineralization within quartz veining. Valley geology has been described in detail by Allen and Richardson and by Osatenko and Jones (2). The exploration sampling program and identification of diamond-drill sample bias have been discussed by Armstrong and Newman'»."

Jan 1, 1988

By I. Silin, M. Stapelmann, H. Wotruba, K. M. Hahn, C. Gerold, J. Katzmarzyk

New deposits are often characterized as low-grade and complex ore bodies. To date, processing of fine grained ore deposits implies complex processing routes with high energy consumption. For that reason, the investigation of dry grinding, e.g. with vertical roller mills (VRM), is an approach to save energy reserves. It is already proven that dry grinding can influence subsequent processing steps. In terms of flotation, the surface characteristics of the minerals are crucial for a successful flotation process, e.g. the sufficient adhesion of mineral particles and air bubbles. Wet grinding results in different surface properties of the product entering the conditioning stage than dry grinding, which has direct influences on the subsequent flotation process. To investigate the consequences for flotation, processing of a copper sulfide ore containing chalcopyrite and bornite was investigated, including grinding and rougher flotation. The effects of wet tumbling mill and dry VRM grinding on the degree of liberation of valuable minerals are characterized using mineral liberation analysis by scanning electron microscopy. The obtained flotation results, as well as the recorded flotation parameters such as dissolved oxygen, oxidation reduction potential and conductivity are presented and discussed. INTRODUCTION Copper production is mainly connected to porphyry copper deposits as main source for copper sulfides such as chalcopyrite and bornite. State-of-the-art processing of these deposits is already established worldwide for decades, combining crushing, fine grinding and subsequent flotation with rougher, cleaner and scavenger stages (del Villar, Desbiens, & Maldonado, Bouchard, 2010). While the demand for copper is increasing, copper grades of the deposits are decreasing and the remaining ore bodies have more complex mineralogy and finer particle size distribution. This implies processing routes with high water and – due to the liberation of fine grained valuable minerals – high energy consumption by fine grinding. One of the main energy consumers in processing plants is the grinding section, which accounts for more than 50% of the energy consumption in processing plants and even 4% of the worldwide energy consumption (Jeswiet, & Szekeres, 2016). Therefore, dry fine grinding alternatives are applied to enhance the overall energy consumption of mineral processing plants: high pressure grinding rolls (HPGR) and vertical roller mills (VRM).

Jan 1, 2019

By Yutaro Fukase

Various types of service robots have recently been developed for guarding facilities, caring for the elderly, carrying objects, and cleaning buildings. As barrier-free facilities improve and their use expands, these robots have more space within which to move inside buildings. Yet robots that move autonomously rely on position-detection systems. Though improving rapidly, these systems are far from perfect in determining positions in certain situations, especially when robots navigate large areas or cross various locations. Our group is working to solve this problem by developing a position-detection system using random-dot patterns on a floor. First, we construct a floor with a random-dot pattern and register the positions of all of the dots into a database. As the robot moves across the floor, a camera on the robot captures an image of the floor beneath it and crops the dot pattern in the image. The cropped dot pattern is matched to the dot patterns in the database to determine the position of the robot and the direction in which the robot is facing or moving. In this paper we propose a self-localization system and matching algorithms derived from a space technology and present the results of several experiments.

Aug 1, 2013

By Christian Ottergren

"Modern crushers offer double the capacity and performance of classic models. In some cases crushers are replacing SAG circuits, the advantages being smaller investment and lower operating costs. Is Tertiary crushing replacing SAG milling as the most optimal grinding method? Does tertiary crushing achieve the same outcomes as SAG milling? This paper considers these questions and provides an assessment of the strengths of tertiary crushing in comparison to other methods. Two case studies: a Scandinavian Platinum Project, and CODELCO, are also presented.INTRODUCTIONResearch on basic parameters in crushing started at Chalmers University in 1993. The initial project has developed and now involves several related areas. Modelling in accordance with new theories has resulted in modified designs which have been implemented and shown improved performance at operating mines in Chile. Sandvik Rock Processing is a partner and a major supporter of this program. This paper will cover some of the achievements and give references to the research reports.The mining industry has for many years mainly used crushers of the traditional 7’crusher concept, with thread adjustment of the setting and with a spring or hydraulic overload system. This machine type has been the workhorse for crushing throughout the world. The explanation for the dominance of this machine is that it has a reliable mechanical design. It can be estimated that about 2000 crushers of this design are still at work.Technical development in all fields utilizes new technologies like high-strength materials, advanced control systems and more extensive use of hydraulics. This is the reason why today’s motorcars, for example, are more efficient, more reliable and more environmentally friendly than their predecessors in the 1950s. Crushers are no exception. This paper will cover experience from the latest-generation cone crushers developed by Sandvik Rock Processing.The parts in this paper related to the CODELCO ElTeniente copper mine in Chile are coauthored with responsible personnel from the operation at the mine."

Jan 1, 2004

By R. B. Fermor

"The tyndalloscope is used in Europe for dust-hazard assessments in both coal and metal mines. Dust-hazard conditions can be directly evaluated by the tyndalloscope in many underground working situations, once the basic standard table or tables have been prepared from representative mine-rock samples.The tyndalloscope is excellent, in many cases, for diagnostic dust sampling during a working shift, because individual readings can be taken to within three-minute intervals. The limitations of the tyndalloscope are also discussed.The author suggests that a combination of both the tyndalloscope and gravimetric sampling methods would be an ideal match for most mine dust-hazard assessments."

Jan 1, 1970

By H. Assadi, S. Reutzel, D. M. Herlach

Intermetallics exhibit unique solidification behaviour due to their chemical longrange order. This includes, for instance, generally slow solidification kinetics, and in some cases, an anomalous partitioning behaviour. In the present work the electromagnetic levitation technique - complemented by theoretical modelling - is used to explore various aspects of this behaviour, as observed in solidification of B2 phase in undercooled melts of the Ni-Al system. Moreover, a phase-field model is developed and used to illustrate the effect of chemical order on the solidification kinetics of a B2 phase in a model system. The phase-field model provides an additional basis for the simulation of solidification microstructures in intermetallic forming systems. Both experimental studies and theoretical work signify the role of chemical order in solidification of intermetallics.

Jan 1, 2006

By M. Maeda, H. Sasaki

Dissolution characteristics of metals vary significantly when they form alloys with other elements. Because hydrometallurgical processes are essential in separation and refining of non-ferrous metals, it is important to study behaviors of alloys in aqueous solutions. The authors have studied dissolution characteristics of precious metals in acid solutions using electrochemical measurement. When precious metals are alloyed with Zn, its dissolution is promoted by an increase in surface area caused by the preferential dissolution of this metal. The electrochemical study also revealed that precious metals dissolved from some alloys at unusually negative potentials; the underpotential dissolutions are explained by activations of these metals in the dealloying.

Jan 1, 2014

By D. Djokic

One of the most attractive features of electron beam curing as a process for manufacturing composite structures is the potential for attaining very low levels of residual stress as compared to thermal curing. This residual stress reduction is important both for the potential to reduce composite failure strains at low operating temperatures and the associated reduction in process-induced deformation. Previous work has demonstrated that it is possible in some cases to significantly reduce residual stress development during irradiation and also avoid development of additional residual stress during post cure. In this paper, simple L-shaped composite laminates were used to study the development of residual stress and deformation during thermal post-cure of specimens that were already partially cured using different radiation doses. Following post-cure, these specimens were also subjected to high-temperature loads to study creep behaviour under service conditions. Aerospace

Jan 1, 2006

By Ata Akcil, Z. B. Karshigina, Ye. G. Bochevskaya, Z. S. Abisheva

"Phosphorus slag is the most heavy-tonnage waste of yellow phosphorus production, which is stored in the dump fields for many years creating ecological problems in the regions. Despite of the actions taken to utilize the slags, most of them remain in the slag disposal area. One of the relevant and priority directions is rare-earth metals production (REMs), presence of which in the phosphorus slags allows considering the latter as an acceptable raw material source. Phosphorus slags contain about 30–40 wt% of silicon dioxide, therefore they can serve as a source of production of precipitated silicon dioxide highly required in different industries.The purpose of this work is the most complete REMs recovery in the solution while leaching and subsequent processing of siliceous cake. The work shows results of researches on establishment of the chemical and phase compositions of phosphorus slags, determination of the forms of presence therein of REMs compounds, processes of phosphorus slag leaching by nitric acid and processing of produced siliceous cake by NaOH solution.Based on the data of the instrumental and chemical methods of phosphorus slag analysis, it was established that it consists of pseudowollastonite a-CaSiO3 for 90–92%. It was found out that REMs are present in it in the form of carbonate apatite Ca10(PO4)6CO3 or rare earth apatite, and La2S3 compound inclusions.Optimum parameters of phosphorus slag leaching process were selected: HNO3 concentration 7- 7.5 mol/L; L/S ratio = 2.6–3 mL/g; temperature – 50–80o?; duration – 1 h; pulp stirring – 500 rpm. Recovery of SREMs, CaO, Al2O3 and Fe2O3 into the solution were achieved at 98.0, 99.1, 99.0 and 18.8%, respectively. Presence of 10 elements of the rare earths group in the phosphorus slag was established. It was found out that recovery of almost all REMs is within ~92–99%, except for Sc and Lu – ~39% and ~28%, respectively.For the purpose of optimization of siliceous cake leaching by NaOH solution, influence of some physical and chemical parameters was studied: N?O? concentration, L/S ratio, temperature, and duration. Results of the experimental data will serve as a basis for development of the technology of complex processing of the technological waste of phosphorus industry with production of REMs concentrate and precipitated silicon dioxide."

Jan 1, 2016

By Jayesh B. Patel, Zhongyun Fan, Hu-Tian Li

"Melt conditioned direct-chill (MC-DC) casting is a novel technology which combines vertical direct-chill (DC) casting with a high shear device directly immersed in the sump for in situ microstructural control. In this paper, the solidification mechanism of DC casting under varying conditions is discussed. The temperature profiles in the sump were measured under the steady state casting conditions by using sacrificing thermocouples. Detailed comparisons of the derived thermal condition are made. The individual role of grain refiner additions, natural thermosolutal convection and forced convection in the sump and the interplay of these factors in determining the solidification structures of DC cast billets are discussed. The MC-DC casting technology can be used to control microstructural constituents and casting defects in DC cast billets/ingots by in situ manipulating of the thermal and fluid flow conditions.INTRODUCTION Direct-chill (DC) casting of aluminium, has been the essential commercial process for producing feedstock suitable for subsequent processing, such as extrusion, rolling or forging. Fine and equiaxed grain structures in the as-cast billets/ingots are required to enable a fine and uniform distribution of second phase particles and microporosity. This leads to higher productivity, more cost-effective homogenisation and more efficient downstream thermomechanical processing. The addition of chemical inoculants has been the standard industrial operation prior to casting for grain refinement of Al alloys. However, it has been established that less than 1% of the grain refiner particles added actually act as heterogeneous nuclei to refine the grain structures, showing a very low grain refining efficiency (Greer, Bunn, Tronche, Evans, & Bristow, 2000). Moreover, the remaining particles from the grain refiner addition in the final casting may cause surface defects during downstream processing. A major issue of the metallurgical quality of large sized ingots/billets is the non-uniformity of microstructures even with chemical grain refiner additions. This is due to the fact that the grain structure formed in the different zones of the billet depends on the local chemical composition and local cooling rate. The local cooling rate can vary from 0.4~1 K/s at the centre of the billet to around 10–20 K/s at its surface zone (Nadella, Eskin, Du, & Katgerman, 2008). The large thermal gradient along radial direction between billet surface and interior of the melt during conventional DC casting induces thermal stress and cold cracking even with grain refiner addition. Therefore the control of casting defects, such as macrosegregation, porosity, cold/hot cracking and distortion of the billets/slabs, etc., is still challenging in industry, causing high scrap rate of DC cast ingots/billets even with grain refiner addition."

Jan 1, 2018

By Chia-Chi Chiu, Meng-Chia Weng, Tsan-Hwei Huang

"This paper proposes a biconcave shape bond model for the distinct element method (DEM) to simulate cementation between two circular particles in geomaterials. Rather than an original parallel bond model between particles, the proposed model adopts the more realistic shape of cementation and considers the elastic response of cementation under external loading. The stress field and force-displacement relationship of the biconcave shape bond is based on Dvorkin’s theory, and three modifications are adopted: (1) A superposition method is applied to improve the correctness and symmetry of the stress field, and it also provides a method of addressing the status when both connected particles rotate; (2) To simplify the input parameters, the tangential movement is replaced by the normal deformation and rotation between particles; (3) To accelerate the calculations, variables are extracted in analytical procedures, which provide an efficient method for applying the bond model with only one matrix inversion. With these three modifications, the new biconcave shape bond model is created.To assess the validity of the proposed model, this study compared the elastic deformation in a single bond with an elastic analysis performed using the finite element method (FEM). After verification of the proposed model, a series of sensitivity analyses was performed to explore the effect of bond shape and the differences from the parallel bond model. For a single bond, the results showed that a biconcave model can represent the mechanical behavior of a biconcave shape bond and is effective with different bond shapes. The stress fields calculated by the biconcave model were more similar to the FEM results than those obtained using Dvorkin’s theory. The width and thickness of a bond have a considerable effect on its stiffness, and the variation of thickness decreases with the width of the bond. In addition, the required parameters can be acquired directly from real bond material rather than using the back analysis procedure for parameters.The biconcave model was further implemented in DEM software Particle Flow Code 2 Dimension to certify its applicability in geotechnical engineering. Using this model, a series of uniaxial compression test simulations was performed to analyze the macroelastic responses of specimens. The results showed that the macrotangential elastic modulus and Poisson’s ratio had a regular tendency, and they agreed with the stiffness variation in a microbond. This finding can assist in determining correlations between microand macroproperties and provides an innovative method for simulating the behavior of cemented granular material."

Jan 1, 2015

By Weng Fu, James Vaughan, Stefan Lakemond

Uranium bearing copper sulphide flotation concentrates produced from iron oxide copper gold uranium (IOCG–U) ore contains radionuclides such as 238U, 230Th, 210Pb, 226Ra, 210Po, which have the potential to reduce their marketability, thus posing a challenge to the industry. Thus, a two–stage leach process has been proposed in this study. In first stage, a sulphuric acid leach process effectively dissolve most of the 238U and 230Th into solution, but other radionulclides (mainly 210Pb, 226Ra and 210Po) remain associated with copper sulphide minerals owing to their low solubilities in sulphuric acid solution. In the second leaching stage, the use of methanesulfonic acid (MSA, CH3SO3H) is investigated to selectively dissolve the 210Pb, 226Ra and 210Po from the residue of the first stage. The results indicate that 96% of 238U, 87% of 230Th, 90% of 210Pb, 86% of 226Ra and 17% of 210Po are dissolved using 3 mol/L MSA solution at 90°C for 3 hours, which represents a dramatic decrease in the radioactivity of the copper concentrate. INTRODUCTION Australia is host to one of the largest iron oxide copper–gold–uranium (IOCG–U) deposits in the world. Most of the value in these deposits is associated with copper. In mineral processing, the gangue minerals are separated from copper sulphide minerals that report to a copper flotation concentrate. However, due to the strong association of uranium with copper minerals and hematite, even clean copper concentrates can contain significant amounts of uranium (238U) and its radioactive decay elements, of which thorium (230Th), radium (226Ra), lead (210Pb), and polonium (210Po) are the long life radionuclides. These hazardous radionuclides negatively affect the marketability of the copper concentrates. Customer copper smelters in China, Japan and Europe may consider the radionuclides penalty elements or may not be able to process the feed. Therefore, there is a strong motivation to remove radionuclides from copper concentrates at the mine site before shipping to custom smelters in global market. Hydrometallurgical leaching has been widely employed to remove radionuclides from different kinds of minerals such as copper concentrates (Ragozzini & Sparrow, 1987), zircon concentrates (Aral, Sparrow, McDonald, & Norgate, 2007), and coal ash (Lei, Qi, Sun, Xu, & Wang, 2014). Leaching using sulphuric acid (H2SO4) solutions is the most widely used process for the extraction of uranium from uranium ores due to the relatively low cost and wide availability of the acid (Bhargava et al., 2015; Gilligan & Nikoloski, 2015). The leach process involves treating ground ore slurry with sulphuric acid at elevated temperatures (typically 60–90 °C) under oxidising conditions in order to convert the uranium in the minerals 2+ from the relatively insoluble tetravalent form (UO2) into water–soluble hexavalent state (UO2), which then complexes with SO42- and forms UO2(SO4)22- in solution. The uranium oxidation is generally carried out in the presence of ferric ion (Fe3+), regardless of the reagent and oxidant used. The most commonly used oxidants for uranium include sodium chlorate, pyrolusite and oxygen (Ring, 1980). These oxidants act indirectly by converting ferrous sulphate, formed by the oxidation reaction of UO2 in slurries, into ferric sulphate. The presence of Fe–containing gangue minerals such as hematite in the ore usually provides sufficient Fe required for the oxidation of UO2. After sulphuric acid leaching, the locked thorium (230Th), radium (226Ra), lead (210Pb), and polonium (210Po) elements are chemically liberated from hematite and uranium mineral grains (Ciobanu, Wade, Cook, Schmidt Mumm, & Giles, 2013). However, the extraction rate of radium (226Ra), lead (210Pb), and polonium (210Po) in sulphate solution is very low due to the limited solubilities of (Ra, Pb, Po)SO4 (Bagnall & Freeman, 1956; Liu & Papangelakis, 2006; Nikitin & Tolmachev, 1933).

Jan 1, 2019

By W. D. Gould, A. Kapoor

Acid mine drainage (AMD) is characterized by low pH and high concentrations of sulfate and dissolved metals such as iron, manganese, aluminum, zinc, and copper. Chemical treatment of AMD achieves pH neutralization and toxic metal removal but also produces large quantities of bulky sludge that requires long-term storage facilities and monitoring. Chemical treatment of AMD achieves only partial removal of sulfate (SO4) and total dissolved solids. Sulfate reducing bacteria (SRB) have been used for the removal of sulfate from industrial process wastewaters. The biological sulfate reduction process generates sulfide and alkalinity. The sulfide produced in the biological sulfate reduction process is used to precipitate metals present in AMD as their respective sulfides and the alkalinity generated is used to neutralize the AMD. This review article will present an overview of biological sulfate reduction processes using SRB, bioreactor configurations, AMD treatment studies, and full-scale systems in operation for the treatment of acid mine drainage.

Jan 1, 2004

By L. C. Kitchener, K. Vollenwyoer

"This paper describes the development of an automated, 70-ton capacity, underground electric trolley truck at Inco Ltd. The purpose of the project is to provide a high capacity and high productivity haulage system to suit continuous loader applications in existing mining horizons where conveyor belt application is not immediately practical. IntroductionWith the start o f a program by Inco in mid-1983 to develop a continuous loader for bulk mining of our hardrock orebodies, the need for a rapid ore transportation system was recognized to match the increased extraction rates planned. Two methods were investigated, truck haulage and conveyor belt. As a result, a conveyor belt system has since been designed and installed with a continuous loader at Stobie Mine and an electric truck has been designed, fabricated and assembled, with shop testing underway. This paper deal s with the latter project. BackgroundMany existing mining horizons which could utilize continuous loaders do not have the straight runs required for conveyor belts. In these situations, truck haulage would be the only alternative of the other transportation methods that would be practical. In order to match the high productivity potential of the continuous loader, however, a more efficient trucking system is required than would be available with conventional diesel powered trucks or with electric truck designs commercially available, or under development. A higher capacity truck and an automated operation is necessary so that the application of additional units to suit increasing haulage distances matches loader output without reducing over-all productivity because of the need for additional operators.A first effort to work with a major electrical manufacturer was unsuccessful and resulted in a project delay of almost one year. In November 1984, an investigation into the concept was reinstigated with UTDC, and an agreement to start design was reached in April 1985."

Jan 1, 1988

By W. A. Gow, J. A. Vezina

"A new process for treating scheelite for the production of tungstic tri-oxide is described. The novelty of the process resides in that an ion-ex-changer is used to convert sodium tungstate to either ammonium tung-state or tungstic acid.The process consists of a conventional hydrochloric acid leach of the scheelite concentrate, and the dissolution of the impure tungstic acid thus produced with sodium hydroxide at pH 8. The sodium tungstate solution is clarified and passed through a column of Dowex 50Wx8 ion-ex-change resin to exchange the sodium ions for either hydrogen or ammonium ions, both being suitable. The tungsten-bearing column effluent is evaporated to crystallize the tungsten as ammonium tungstate; the crystals are washed with nitric acid and water and decomposed by heat to pro-duce tungstic trioxide of high purity.Ninety-six per cent of the tungsten in the concentrate may be re-covered as tungs tic trioxide (W03), and the reagents consumed are 0.7 g HCl, 0.41 g NaOH and either 1.73 g NH.Cl or 225 g HCl per gram of tungsten."

Jan 1, 1966

Grinding with an electrochemically inert grinding media (i.e. high chrome white iron, or Magotteaux’s Duromax® alloys) shifts the pulp potentials to more oxidising conditions, increases the dissolved oxygen content and reduces the EDTA extractable iron concentration when compared with milling with electrochemically active grinding media (forged steel). These changes in pulp chemistry produce cleaner particle surfaces, reduce reagent consumption and increase concentrate grades and recoveries. This paper presents a robust laboratory test program that is able to not only demonstrates these effects but also provide an indication of the magnitude of the improvements that are possible. While laboratory studies are interesting, the proof is in the pudding! So, the paper provides an overview of plant trials conducted at a number of operations around the world, including: Newcrest’s Cadia Operation, Oz Minerals’ Prominent Hill Mine and Glencore’s Ernest Henry Mine. These successful plant trials clearly demonstrate that selection of the right grinding media alloy will yield savings in grinding media consumption and reagent consumption as well as increases in revenue through improved copper, gold and molybdenum recoveries. INTRODUCTION The key to a successful separation in mineral processing is the preparation of particles with adequate liberation under the correct pulp chemical conditions. While the importance of liberation on flotation separations is generally understood and well documented in the literature (Johnson, 1987; Jackson, Sutherland, Gottlieb & Quittner, 1989; Young, Pease, Johnson, & Munro, 1997; Greet and Freeman, 2000), the importance of pulp chemistry is more nebulous, particularly with regard to the impact of grinding media. Extensive work examining the electrochemical interactions between grinding media and sulphide minerals has been completed (for example, Iwasaki, Reid, Lex & Smith, 1983; Natarajan and Iwasaki, 1984; Yelloji Rao and Natarajan, 1989(a); Yelloji Rao and Natarajan, 1989(b)). Broadly, these studies indicate that most sulphide minerals are more noble than the grinding media used during comminution, therefore a galvanic couple between the media and the sulphide mineral(s) exists, which increases the corrosion rate of the grinding media. The corrosion products of the grinding media, iron oxy-hydroxide species, invariably precipitate on to the surfaces of the sulphide minerals thereby affecting their floatability (Johnson, 2002).

Jan 1, 2019

By F. Mercier-Langevin

ABSTRACT; Agnico-Eagle’s LaRonde mine is one of the deepest mines in Canada. Ground conditions in the deeper levels can be very challenging, ranging from hard and brittle to soft and squeezing. As a result, rock mechanics and ground control practices have had to evolve considerably to accommodate progressively deeper mining activities. This paper focuses on the deeper levels of mines and how the difficult ground conditions encountered there have influenced the mining strategy. The first section examines ground control practices and support systems in highly stressed, poor quality rock. The evolution of level layout is also presented. Finally, improvements in stope sequencing are reviewed.

Jan 1, 2010