Search Documents

By George P. Demopoulos, Amani Al-Othman, Terry C. Cheng

One critical issue in chloride hydrometallurgy is the regeneration of the lixiviant HCl that is currently achieved by pyrohydrolysis. In this paper, a low temperature HCl regeneration process was investigated which regenerates HCl and produces saleable gypsum. This process promises to reduce the generation of wastes by the reaction of spent calcium chloride leach liquors with sulfuric acid solution at low temperature. Experiments were performed to determine the optimum conditions of the reaction in terms of temperature, reagent concentrations, rate of reagent addition, mixing and seeding/recycling to produce marketable gypsum and HCl with practical strength.

Jan 1, 2004

By M. S. Moats, C. M. Campbell

Samples of a high impurity (90.05 wt. % Cu, 4076 ppm Pb, 1939 ppm As and 635 ppm Bi) commercial copper anode were characterized and then electrorefined in a laboratory scale cell. Anode inclusions were examined using backscatter mode scanning electron microscopy and energy dispersive spectroscopy. Hundreds of inclusions were measured for size, morphology and composition. Commonly found inclusions were copper oxide (Cu2O), complex oxides (Cu-Pb-Bi-As-O) and copper selenides/tellurides. The weight percent of lead and arsenic increased with increasing inclusion size up to 4- 5 microns. During electrorefining, starter sheet ductility was negatively impacted by thiourea addition. The importance of arsenic (V) concentration on the electrolyte concentration of bismuth was observed. INTRODUCTION Copper electrorefining is a commercial process used to produce the majority of the world’s refined copper. During this process, impure copper anodes are dissolved electrolytically, and high purity copper is deposited on cathodes. As the anodes dissolve, the impurities either accumulate in the electrolyte or report to solids that form on anodes surfaces or at the bottom of the refining cell. These solids are called slimes. Slimes contain precious metals and are collected for further processing. Slimes are also an important outlet for problem impurities such as lead, antimony and bismuth. The electrorefining process is operated in such a way to encourage the deportment of these elements to the slimes. Impurities in copper anodes have been studied extensively by Chen and Dutrizac (1990, 1993 and 2005). The most common impurities found in modern copper anodes include: Ag, As, Au, Bi, Fe, Ni, O, Pb, Sb, Se, Sn and Te. Impure copper anodes are produced by pyrometallurgical methods and have purities ranging from 97.7–99.7% Cu (Moats et al., 2019). The composition ranges of commercial copper anodes from the 2019 worldwide tankhouse survey are given in Table 1. The concentrations of anode impurities vary widely dependent on the source material and prior processing steps. Based on the work of Chen and Dutrizac, both gold and silver are predominantly found in solid solution within the copper grains while a minor amount of Ag can be found in Cu2(Se/Te) inclusions. Nickel is entirely soluble within the copper grains up to anode compositions of 2500–3000 ppm Ni; above which NiO and kupferglimmer phases are formed (Chen & Dutrizac, 1990). As, Bi, Pb and Sb are found in solid solution within copper and within oxide inclusions typically found along grain boundaries. Oxides are formed due to the presence of 0.13-0.18 wt. % O (Chen & Dutrizac, 1990). This is because during solidification of the cast anodes, impurities are enriched in the liquid phase as the copper grains nucleate and grow. The inclusions form from the last liquid to freeze, which is typically along grain boundaries (Wenzl & Filzwieser, 2007; Wenzl, Filzwieser, Mori & Pesl, 2008).

Jan 1, 2019

By M. S. Badollet

"IntroductionASBESTOS FLOATS may be defined briefly as blends of air-borne particles of fibrous asbestos and dusts produced during the milling stages and collected by Cottrell precipitators, dust sheds, or bag-houses.The various grades of asbestos floats on the market contain fibrous asbestos particles ranging in length from microscopic to approximately 1/4-inch. The fines or dusts present in the floats are from 40 microns to 2 microns or less in cross-section.Airborne asbestos particles are of diverse length because they are collected at numerous places in the mill. There are: (1) dusts removed from dry rock storage bins, (2) dusts removed from rock and fiber screens, (3) particles from the tops of collectors, and (4) fines removed by suction from the processing equipment. Sometimes the airborne particles are kept segregated, so that there is a partial separation by gravity. This is accomplished by a series of dust chambers enclosed in a long, rectangular building. The longest and heaviest particles fall nearest to the air flow entrance, the smallest at a point farthest away and nearest the exit. Sometimes the air from the dust chamber building is passed through a series of bag-houses or electric :precipitators ,to collect the extremely fine particles which normally escape to the atmosphere."

Jan 1, 1952

By Patrice Nadeau, Yuejun Zhang, Dan Chen, Liming Huang, Claude Gagnon

"The traditional Denver flotation cell is generally suitable to process material ranging approximately from 5 µm to 300 µm. For floating over 300 µm material, its efficiency is significantly getting lower mainly due to the difficulty to suspend coarse particles uniformly, which decreases the chances of particles to attach to bubbles and increases the chances of detachment.RTFT (Rio Tinto Fer et Titane) owns one of the world’s largest hemo-ilmenite deposits. Considering the whole processing technology, the ore is only crushed to -1180 µm. The crushed ore contains about 0.32% S and most of the sulfur is removed by rotary kilns in the ore preparation plant. In order to achieve a similar S reduction, without emitting SO2 into the air, an alternative technology by flotation was pursued.Laboratory and pilot scale-up tests showed that traditional Denver flotation cell could perfectly remove the sulfur from the material sizing 0-300 µm. For the coarser particle sizes, two different models of equipment were tested to improve flotation efficiency: HF (HydroFloat Separator) from Eriez and CLF from BGRIMM (Beijing General Research Institute of Mining and Metallurgy), China. The D6” HF, which is a device that combines flotation and gravity separation, demonstrated its ability to recover those very coarse particles. As compared to the Denver flotation cell, the modified 25 L CLF coarse particle flotation cell achieved better results at higher pulp solids percentage and with a shorter flowsheet."

Jan 1, 2016

By W. M. Moon, Hugh G. Miller, C. -S. So

"Digital image processing and enhancement techniques have been applied to airborne gamma ray spectrometry data from Sudbury, Ontario. These results have been correlated and compared with the available geological maps to evaluate their usefulness for identifying lithological units. Digital processing allows the correlation of various data sets, and different combinations of images can be tested and viewed as a composite image. Composite images with pseudocolours provide an opportunity to analyze and correlate information that is not otherwise apparent in individual images. Principal component analysis has been applied to the gamma ray spectrometry data to evaluate their efficacy and relative information contents of the measured and computed data. The results of this study indicate that the combined radioelements image (obtained by combining the radioelement image and the ratio images) is effective for defining areas of relative concentration of a specific element in near surface materials. Furthermore, the composite radioelements image (produced by combining three separate radioelement images) and composite principal components image reflect large-scale lithological variations. IntroductionThe Sudbury area is a unique geological structure located in the southern Canadian Shield (Fig. 1). Because the area hosts economically significant nickel-copper deposits (Pye et al., 1984), it has been surveyed in great detail by geological and geophysical methods. In order to obtain meaningful geological infonnation about the Sudbury area, several studies have been carried out with the application of innovative mathematical techniques for geophysical modelling, and attempts have been made to integrate the multisensor geophysical data available for the area (e.g. Gupta et aI., 1984; Moon et al., 1988; Singh et al., 1993). The main objective of this paper is to apply digital image processing and enhancement techniques to airborne ganuna ray spectrometry data in order to determine their usefulness for regional geological mapping."

Jan 1, 1994

By S. Jordanov

The nature of processes that take place on top of copper bearing grains during the suppression of copper acid drainage from mine tailings was studied on a grain model. Cyclic voltammetry (C.V.) was employed as an experimental technique suitable for indirect measuring of copper leaching. Experiments were done in sulfuric acid (pH=2) at electrodes that progressively approach the real situation during acid main drainage, starting with Cu-metal, then with CuO and finally with CuO covered with CaSO4. Oxidation was found to be the only process that takes place on metallic copper electrode anodically polarized up to 2 V vs. Cu/CuSO4 reference electrode. Dissolution is intensive and reaches up to 50 mA.cm-2. When the same was repeated, but on CuO electrode, anodic currents were some 4 times lower than on the bare metallic surface. This indicates that the electrode material is not completely oxidized to copper(II)oxide and the Cu(O) or Cu(I) residues are oxidized during the anodic polarization. This explains the diminished dissolution. Dissolution is further restricted at electrodes covered with CaSO4. It is some 20 times lower than on the bare oxide electrode. When the second layer of CaSO4 was applied, anodic currents were another 15 times lower. Total decrease of anodic currents when transition is made from Cu-metal to CuO covered with 2 layers of CaSO4 reaches up to 7.500 times. C.V. measurements produced a proof that mechanical blockage is the way how lime prevents leaching of copper bearing grains in immobilization experiments referred elsewhere.

Jan 1, 2007

By Q. J. Xu

In blasting sensitive areas, the use of traditional blasting for rock fracture is restricted. Soundless cracking technology has been presented to achieve rock fracture instead of blasting. However, when the diameter of a borehole is larger than 50 mm, it is very dangerous that the soundless cracking agent (SCA) will have a tendency to gush from the borehole, which also leads to cracking failure. In this paper, a new large scale borehole soundless cracking technology is presented, using a new enlarged drill bit and mechanical plugging, which could solve the hole gush problem. Experiments were made to measure the expansive pressure of the SCA working in boreholes of F40 mm and F100 mm. The difference between two sizes of cracking phenomenon was compared and analyzed to show that large scale borehole soundless cracking has larger expansion pressure and faster reaction speed than traditional soundless cracking. Based on the experimental data, finite element analysis was utilized to study the stress concentration and stress distribution between two neighboring large boreholes in several media during the cracking process. Using the data from experiments with finite element numerical simulation, the brittle material fracture condition was analyzed to design the parameters of the borehole mesh. With the theoretical analysis, the technological process and reference parameters of large scale borehole soundless cracking were proposed, including the borehole spacing, burden distance, depth of the borehole and so on. Then a single rock was cracked with the new enlarged drill bit and new plugging, and the results proved the feasibility of the new large scale borehole soundless cracking technology, which achieved the expected goal of improving the cracking ability and reducing the cracking time. This paper presents a new efficient rock cracking method for blasting sensitive areas, and which could apply to mining engineering, demolition engineering, excavation engineering and other engineering applications where there is a demand soundless and non-vibration fracturing of rock.

Aug 1, 2013

By J. Reinhardt, R. Uken, S. S. Chinnasamy

Au mineralization in the Kilpwal Gold Mine is confined to laminated quartz-carbonate lodes and associated alteration along the Klipwal Shear Zone (KSZ) in the upper Mozaan Group of the Mesoarchaean Pongola Supergroup. The brittle-ductile shear zone is characterized by inner and proximal hydrothermal alteration domains that are comprised of chlorite, epidote, sericite, pyrite, arsenopyrite and gold. Possible sources of gold are: (i) paleo-placer U-Au rich conglomerates from the lower Mozaan Group; (ii) the underlying mafic volcanics of the Nsuze Group; (iii) greenstone belts in the basement to the Pongola basin. Post-Pongola granites probably provided the heat to mobilize auriferous fluids into the KSZ.

Jan 1, 2011

By Neville Jordison

Indirect, gravity flow, heat exchangers have become a well established technology in mineral and metallurgical process plants. The technology is a conventional heat exchanger using high efficiency plates, with a free flowing bulk solid on one side of the exchanger and a fluid on the other side. This simple concept leads to many opportunities for achieving greater energy efficiencies in process plants. Indirect heat exchange is much more efficient than direct heat exchange using air such as in a fluid bed or rotary device. When air is used directly, large fans are required, it may also be necessary to chill the air, both high consumers of energy. By contrast, using water as the cooling medium requires only low horsepower pumps, typically only 10% of fan HP. Furthermore there are no stack emissions with the requirement for removal of dust or emissions. Indirect heat exchange also creates the opportunity to recover energy. This can work in two ways: energy can be recovered from a hot bulk solid, to heat pressurized hot water for steam generation or preheat air. Alternatively recovered energy from elsewhere in the plant in the form of hot water, steam, air or thermal oil can be used to preheat a bulk solid.

Jan 1, 2011

By Long Han, A. V. Kalinin, Xiujian Luo, Xiaobo Wang, Xiaoou Xia

"Inertia vibration crusher is a kind of vibration equipment which crushes ore by vibration. When the inertia vibration crusher works, ore between the two moving jaws is subjected to the high frequency contact force, which is produced by the two moving jaws with high frequency synchronous reciprocating motion. The synchronous motion of the two moving jaws depends on the self-synchronous feature of the inertia vibration crusher. To study the self-synchronous feature of the equipment, the dynamic model was established, in which relative parameters were taken into consideration. The kinematic coupling relations of the assemblies are discussed, and appropriate calculation method is chosen to solve the vibrating differential equation. Whether the two vibration exciter can realize synchronous operation depends on the ability of the vibration system's capture moment. Results show that though the two rotors’ motors and damping coefficients are different, and two jaws’ damping and stiffness coefficients are also different, as angular velocities of the two unbalanced rotors reach a certain value, the vibrating system can be stable. Their angular velocities tend to be equal, and the swings of the two moving jaws can be the same. The horizontal vibration and swing of the frame are large in a few seconds after starting the machine. When the system runs stably, the horizontal vibration and swing vanish, and the vertical vibration is stable. The study and its results can provide reference for the optimization design and parameter setting of inertia vibration crusher and related vibratory equipments.INTRODUCTIONMaterials can be easily broken by using the inertia force of the vibration exciter, which can effectively realize the selective crushing, reducing excessive combinations and the energy consumption, as introduced by Zhang in 2005. The initial micro crack between crystals in the material increases and new cracks can be manufactured because of the high frequency impact and the extrusion of the vibration crusher, so vibration crushing equipment can make it possible for any high strength brittle material to be broken theoretically. Inertia cone crusher and inertia vibration crusher have been successfully used in the treatment of metallurgical slag and construction waste, and it verifies the efficiency of vibration crushing."

Jan 1, 2016

By Jorgen Elbrond, Yve Lizotte

"A mine evaluation method based on the use of a computer program that models mining with an open-ended dynamic program is presented in this paper. It is demonstrated with an example how the method is applied, how some of the decision variables are related in the particular industrial environment and how these decision variables affect the economic benefits of mining.IntroductionTwo distinguishing characteristics make mining a particular industrial environment: exhaustible resources of a given ore deposit and heterogeneousness of the ore grade spatial distribution in the ore deposit. These characteristics, inflation, uncertainty and cyclical price variations which greatly affect estimated cash flows also contribute in rendering difficult the evaluation of the economic outcome of mining at the preliminary planning stage.Decision variables and their ranges are associated with the mine plan; basically, they include choices of the mine's nominal capacity (mining and milling), the sequencing of mining through the deposit, the ranges of possible production rates and cutoff grades, and the stockpiling policies. The mine's nominal capacity must be decided at the planning stage, but this capacity choice must take into account flexibility to modify other decision variables as mining commences and uncertainty resolves.Although it is generally accepted in discounted cash flow analysis that the sequence of mining must proceed from the richest to the lowest-grade stopes (with correspondingly ajusted cutoff grades), this may not produce optimum benefits when cyclical price variations are considered.Mining rates and cutoff grades can also be adjusted to changing economic conditions, taking into account the limited resources of the ore deposit. Thus, when prices are thought to be in the trough of a cycle, production can decrease to preserve ore for expected greater future profits. When prices rise, mining rates can increase possibly even over the mine's nominal capacity. In both cases, the machinery's effectiveness shall not be-optimally utilized; this will be reflected particularly by the variations in the concentrator's metal recovery and the concentrate grade output."

Jan 1, 1982

By W. J. Mcgaughey, R. G. McCreary, S. C. Maxwell, R. P. Young

"Seismic tomography is a process for obtaining images or maps of seismic velocity or other seismic properties of a rock mass. Seismic velocity images reveal variation in elastic moduli which, in tum, are related to several properties required in the geological or geomechanical assessment of a rock mass. Seismic velocity is sensitive to lithology, discontinuities, and in situ stress. Spatial or temporal variation of these properties may be indirectly assessed. Tomographic measurements are sensitive to volumes of ground, rather than determinations at points, or along lines or surfaces, as in conventional geological or geomechanical measurements or mappings.Tomography surveys are complementary to conventional measurements as they have the capability to interrogate a substantially larger volume of ground. They are thus useful in discerning trends or patterns in regions between or surrounding conventional ""point"" measurements of lithology, rock quality, stress, or other parameters of interest. Seismic velocity images give broad indications of trends in velocity; their spatial resolution of ground properties is typically on the order of five to ten per cent of the nominal survey dimension.Research in seismic tomography has been carried out for several years, and the capabilities and limitations of the technique in mining environments are beginning to be understood. This report reviews the present capabilities of seismic tomography surveys in mining, emphasizing rock mechanics applications. Six case studies are used as examples to demonstrate the capabilities of the method in assessing lithological variation, density and orientation of discontinuities, and the effects of stress."

Jan 1, 1994

By T. G. Joseph

The chicken and egg scenario where adverse truck motions cause ground deterioration and poor ground profiles that in turn cause adverse truck motions is a downward deterioration spiral that dominates in our industry. If we can remove one action, the reaction must stop and vice-versa. A simple 'truck to excavator' load data analysis and wireless communication system is outlined in this paper; that will provide visual assistance to the excavator operator in achieving improved load placement and balance in a truck body. In turn this will reduce the subsequent hauler duty cycle adverse motions and g levels that contribute to structural fatigue, higher tkph, reduced tire life and ongoing maintenance of haul roads

Nov 1, 2011

By James J. Roettger, Robert J. Mitchell

"The results of a series of model stope pours designed to investigate working pressures on bulkheads during hydraulic pouring of classified tailings backfill are reported. Total bulkhead pressures and fill water pressures were monitored under the condition of a fully saturated backfill. Similitude of the model testing is discussed and equations are developed to estimate bulkhead pressures under prototype conditions. The model results show that good base drainage, combined with a bulkhead setback, can reduce the expected bulkhead pressures to values such that timber or concrete block structures should be capable of supporting a saturated backfill. Introduction Bulkheads are used in underground running operations to block drift openings in order that hydraulically placed sand backfill can be contained in stope pours. Whenever possible, the sand fill is designed to have sufficient percolation rate so that excess hydraulic transport water will gravity drain out through the bulk headed drifts. This avoids costly decanting systems. Early bulkhead design assumed that the bulkhead pressure could be as high as 0h = Hy where H is the fill height and ""y is the saturated unit weight of the fill (Thomas et al., 1979)(1). A typical design pressure for a 50 m fill height would be 1250 kPa giving a design force of 12,500 kN on a bulkhead located in a drift of 10m2 in area . Typical bulkheads were 1 m thick heavily reinforced concrete structures formed and poured into a notched drift. Not only were these expensive structures but the associated problems of inside drainage systems and curing time delays increased production costs. As experience with bulkheads for large bulk pours increased and fill pressure measurements became available [see, for examples, Libby et al., 1975(2), Askey et al., 1978(3)] , 'free drainage' timber and concrete block bulkheads were designed. Substantial savings have been realized using these types of bulkheads but greater engineering design and monitoring of backfill pours is necessary to ensure that backfill pressures do not exceed the bulkhead design pressures.The effective and total stress components of fill pressure, the engineering concepts associated with the 'free drainage' design and some detailed design considerations have been discussed by Smith and Mitchell (1982)(4) . It is important to the safe use of these designs, however, that the basic engineering concepts be demonstrated and communicated to those responsible for the day-to-day backfill operations. This paper describes and explains observations from a series of model studies designed to measure bulkhead pressures in a saturated fill."

Jan 1, 1984

By P. B. Marchant

"Based on laboratory and pilot scale continuous biooxidation of complex sulphide concentrates, commercial processing design and scaleup considerations are discussed. Capital and operating cost estimates for commercial biohydrometallurgical operations are summarized and potential applications of biotechnology are discussed. Biooxidation as an oxidative pretreatment alternative to enhance precious metals extraction from refractory sulphide concentrates in stirred tank reactors has received considerable attention recently due mainly to advances in the practical applicability of the process. Biooxidation of sulphides is certainly not a new process, however, application and control in large scale hydrometallurgical operations to treat refractory sulphides remains conceptual and the limited data available is restricted to relatively small laboratory and pilot scale operations. It is the intent of this paper to indicate scaleup and plant scale process design considerations for commercial bioleach circuits, based on recent operating experiences with laboratory and pilot scale continuous bioleach systems. An indication of the expected range of applications will be presented parameters for optimization will be discussed."

Jan 1, 1986

By B. Misra, B. S: Sastry, Kollu S. Rao

"This paper reports the results of a finite element study of the geothermal heatflow into dry mine airways. For isotropic and unsteady state conditions the heatflow into mine airways is studied for a range of surface heat transfer coefficients between rock and air, and age of the airway. Dimensionless temperature gradient values are presented in tables for different values of Boit and Fourier numbers and the results are compared with Starfield tables and Gibson algorithm. It is found that Starfield tables have consistently over-predicted the G values with errors ranging from 2% to 10%. The differences between results obtained from the finite element study and the G values calculated from Gibson's approximation method are mapped. The small error values over a large range of Fourier and Biot numbers confirm the suitability of Gibson's algorithm to rapidly calculate G values for estimating the heat transfer from surrounding rock to mine air.IntroductionIn many underground mines heat is a major problem, and the provision of acceptable working conditions requires considerable expenditure on ventilation systems. The rational design and operation of these systems depend upon an understanding of the various sources of heat in the mine. The natural source, i.e. geothermal heat, contributes up to 80% of total heat added to mine air and it is difficult to analyze and predict the heat owing to a number of influencing variables. The problem of geothermal heat flow has been studied by many investigators (Goch, 1940; Starfield, 1966; Hemp, 1987; Amano et al., 1982; McPherson, 1986).The primary concern of this paper is to develop a better ready reference dimensionless transient temperature table for estimating heatflow at any stage of mine airway life."

Jan 1, 1994

By R. L. Guerguerian, Eugene Bercel

"Grinding mill hydrostatic trunnion bearings require an external pumping source to provide and maintain the oil film between the bearing members. In order to guarantee a predetermined minimum film thickness, the lubrication system tends to be oversized. The oil film is ""indirectly"" controlled by flow, pressure and temperature monitors with fixed settings on the conservative side. This can lead to excessive maintenance and abbreviated life for the lubrication system components. A reliable method of monitoring actual film thickness would not only provide greater mill availability, but also minimize maintenance costs.This paper describes the instrumentation installed in Dominion hydrostatic bearings, and presents results of field tests where the output of that instrumentation was recorded under various operating conditions.IntroductionThe trend toward larger and more sophisticated grinding mills has made the operators of these machines increasingly vulnerable to financial loss, as the cost of downtime and repairs has increased directly with machine size. In order to guard against such losses, it is becoming imperative that large, sophisticated grinding mills be equipped with protective instrumentation to monitor some of the critical operating parameters and to identify events and trends which, if they go unnoticed, can lead to excessive maintenance costs and machine downtime. The idea of protective monitoring systems is not new. The operators of certain types of machinery where a high degree of safety is required or where machinery health can deteriorate very rapidly, as in the case of high-speed turbo-machinery, have long been using protective instrumentation on their machines. The increased awareness of the benefits of monitoring machinery conditions and the availability of reliable and relatively low-cost instrumentation of a large range of sophistication is making the practice now widespread. Traditionally, grinding mills have not been considered as high-risk machinery requiring instrumented protection. However, the trend, mentioned earlier, toward employing fewer, but larger capacity, mills increases the risk of significant disruption of production, and therefore measures to minimize the risks are desirable."

Jan 1, 1981

By D. A. Beck

The load-deformation response of discontinuous rock under static and dynamic loading conditions has been simulated using Explicit Finite Element models. The intent of the analysis was to investigate the effects of specimen size and confining stress on strength, dilation and comminution. The simulations allow the development of homogenised constitutive material properties for discontinuous rock masses using laboratory scale measurements and representative Discrete Fracture Networks (DFNs). A procedure for this is presented which includes a comparison of measured seismic response in a mine to the Dissipated Plastic Energy (DPE) that is released in the simulated rock masses. The models also show how confinement and scale affect the stress-strain and DPE response of the simulated rock specimens, reproducing a number of known rock phenomena that are often poorly captured in geotechnical modelling. A case study is presented showing a satisfactory match between the model-derived, homogenised material properties and values achieved by calibration of a mine-scale model where many thousands of seismic, displacement and damage measurements were available.

May 1, 2009

By T. Gonzales, M. Maleki, M. Caçador, B. Climenhaga, H. Ghorbani

The campaign life of furnaces in the copper making industry is greatly affected by damage caused by normal operation cycling and abnormal conditions. Proper monitoring and assessment of the existing conditions and safe remaining life of the vessels and their refractory lining is key to prevent an unplanned early replacement. This paper presents an industry-proven refractory management program as well as a typical fitness-for-service assessment of a rotary vessel shell in order to extend the campaign life of copper making furnaces and enhance safety. The furnace refractory management system involves a comprehensive audit and monitoring program which has been successfully applied to several copper flash smelting furnaces over the past 15 years. The fitness for service assessment provides a methodology to estimate the remaining life of the steel components by evaluating the existing damage and future damage rate based on the historical survey data. The above practices can provide the operator with cost savings by extending the vessel campaign life in lieu of implementing more rigorous refractory lining and shell audits. INTRODUCTION Primary copper smelting is generally divided into two categories of flash smelting and open bath smelting. There are many different types of vessels that can be used to convert the copper concentrate to blister copper including, flash, Mitsubishi process, TSL (ISA/Ausmelt), SKS Bottom Blowing, Anode and Teniente/Noranda furnaces, reactors, and Peirce Smith converters. Each vessel has its own complex and intense environment which requires careful refractory and steel design to withstand the severe thermomechanical and thermochemical attacks within its campaign life. The campaign life of furnaces is greatly affected by damage caused by normal operation cycling and abnormal conditions. Proper assessment of the existing conditions and safe remaining life of the vessels and/or refractory lining is key to prevent an unplanned early replacement. This paper presents an industry-proven refractory management program as well as a fitness-for- service assessment methodology to estimate the remaining campaign life of copper making furnaces resulting in cost savings and enhanced safety of the operating vessels.

Jan 1, 2019

By L. Xia, B. Hart, K. Douglas1, S. C. Chelgani

Development work to optimize a flotation flowsheet for rare earth element (REE) recovery is underway. The original approach used alkyl phosphates and phosphoric acid ester as collectors to concentrate REE minerals. To improve REE recovery, hydroxamates as alternative collectors were investigated. In this paper, micro flotation of REE minerals using salicylic, benzoyl and naphthoyl hydroxamates is reported. Unlike phosphonic collectors, slime removal does not show a significant effect on REE recovery when using hydroxamates as collectors. Among the three hydoxamates, the grade of La, Ce, and Nd for concentrates produced by salicylic hydroxamate is the highest. The recovery response with naphthoyl hydroxamate is similar to that of salicylic hydroxamate; good grades for La, Ce, and Nd, less effective for Nb, Y, and Zr. The data indicated an affinity by salicylic and naphthoyl hydroxamtes for LREE over the HREE minerals. In comparison, benzoyl hydroxamate indicated an affinity for Nb, Y, and Zr. Temperature effects on REE recovery were also studied. The grade and recovery of REEs generated by flotation using a mix of salicylic and benzoyl hydroxamates at room temperature was almost identical or even better relative to the recovery using naphthoyl hydroxamates at elevated temperature.

Jan 1, 2014