Search Documents

By R. W. Culley

"In many areas of Saskatchewan, known gravel deposits have been depleted or are diminishing rapidly; in other areas, particularly in the north, demands for all-weather highways and access roads are far exceeding the supply of gravel sources with which to surface them. These two problems have made conventional methods of air-photo and ground surveys insufficient for gravel location. In the first case, hauling costs on construction now warrant searching for buried deposits and for smaller, less obvious surficial deposits that may be closer to the project. In the second case, search and access conditions are so difficult and costly that the ratio of successes to failures must be kept very high. The Department of Highways has long been aware of the oncoming scarcity of quality gravel deposits and is continually investigating ways of forestalling it. One of these ways is the use of airborne geophysical methods that permit rapid coverage of large areas and that sense and discriminate between earth properties to a significant depth below ground surface. In 1967, the Department began an investigation of an airborne conductivity survey method called INPUT*, or ""Induced Pulse Transient'', leading to a trial in 1968 and data analysis in 1969. The results of this trial initiated• modifications to the technique to improve its sensitivity for mapping shallow deposits. Part way through this modification in 1970, a decision was made to change to an airborne resistivity survey method called EPHASE*. Trials with this technique were conducted and analysed in 1971. This paper is an explanation of the E-PHASE system and a summary of the results from one of three areas mapped in 1971."

Jan 1, 1973

By Richard Hurteau

Design and validation of an integrated guidance system for articulated ground vehicles is investigated. The development of an autonomous industrial vehicle must take into the account the specific geometry of these vehicles; they can be composed of a tractor with 1 or 2 trailers or of articulated type like LHD. Moreover the tractor-trailers type vehicles can have on-axle hitch configuration or positive/negative off axle configuration. The path-tracking of a tractor-trailer vehicle in restricted space is presented and discussed in this paper. Recent results obtained in simulation and validated by experimentation are also presented. These studies can lead to better ways of maneuvering an articulated vehicle in a restricted space or automatically executing of docking and parking maneuvers

May 1, 2002

By S. Fox, Y. Fujita

Increasing demand for rare earth elements (REE) is expected to lead to new development and expansion in industries processing and or recycling REE. For some industrial operators, sending aqueous waste streams to a municipal wastewater treatment plant, or publicly owned treatment works (POTW), may be a cost effective disposal option. However, wastewaters that adversely affect the performance of biological wastewater treatment at the POTW will not be accepted. The objective of our research is to assess the effects of wastewaters that might be generated by new rare earth element (REE) beneficiation or recycling processes on biological wastewater treatment systems. We have been investigating the impact of yttrium and europium on the biological activity of activated sludge collected from an operating municipal wastewater treatment plant. We have also examined the effect of an organic complexant that is commonly used in REE extraction and separations; similar compounds may be a component of newly developed REE recycling processes. Our preliminary results indicate that in the presence of Eu, respiration rates for the activated sludge decrease relative to the no-Eu controls, at Eu concentrations ranging from <10 to 660 µM. Yttrium appears to inhibit respiration as well, although negative impacts have been observed only at the highest Y amendment level tested (660 µM). The organic complexant appears to have a negative impact on activated sludge activity as well, although results are variable. Ultimately the intent of this research is to help REE industries to develop environmentally friendly and economically sustainable beneficiation and recycling processes.

Jan 1, 2016

By P. C. Garg

"IntroductionThe Central Mine Planning and Design Institute (CMPDI) of India, started planning the extraction of thick seams highly susceptible to heating in 1977by the French method of sub-level caving and/or multi-slicing. Nitrogen flushing was proposed for inhibition of heating by the author in one such project - the Kotadih colliery.Inhibition of heating was unheard of in the Indian coal industry before 1977-78. The usual practice was to seal off a district or a part of the mine or the entire mine when spontaneous heating occurred. With very little equipment in a normal bord and pillar district and a low production rate, the financial loss in capital assets and in production did not warrant any serious thought for inhibition of spontaneous combustion. With the planned advent of longwall mining, particularly sub-level caving, with heavy capital investment as well as high production potential, the sealing of a longwall face due to spontaneous heating could not be considered an appropriate solution.Principle of Inhibition of SpontaneousCombustionFrench engineers have established that a fire will not break out when oxygen is 15% or lower in the general body of the air. However, once a fire starts, the percentage of oxygen has to be reduced to 2% - 4% to extinguish it. It is this principle which has been used at Blanzy Coalfield in France to inhibit heating and it is claimed that this has retrieved the integral sub level method of mining. Nitrogen infusion has been used in Frence since 1978 to keep the oxygen content below 14% in the goaf."

Jan 1, 1987

By Gulshan Kumar Pradhan, Yogendra Pratap Singh, Dhawanm Nikhil

"Potassium (K) is one of the essential elements for the growth of plants and thereby for humans. In fertilizers, potash demand has been steadily increasing at ~3.5% annually. Water soluble potash deposits are rare and highly localized. India is neither present on the world potash production map nor it has adequate potash rich rocks. The K-bearing minerals are recovered either by using conventional underground mining methods or though solution mining methods. India possesses a vast resource of silicate rocks such as glauconitic sandstone and Feldspar. These rocks are basically a group of alumino silicate of potassium, sodium and calcium (K2O%: 5-12, Na2O%: 3-10%, SiO2%: 52-65, Al2O3%: 15-20, Fe2O3%:, 5-7 and MgO%: 2-3.5).The K extraction from silicate rocks has received little attention probably due to the slow release, the locked structure of alumina-silicate minerals, and the unavailability of appropriate economic processes & their know-how. In fact due to this India imports all of its potash demand (about 3.5 million tons per annum) from different countries.In the present work, an attempt has been made to identify the structural and chemical alteration of desired K mineral phase in silicate rock (~K2O%: 10.5, Na2O%: 2%, SiO2%: 55, Al2O3%: 19, Fe2O3%, 5-6, MgO%: 2.5) under different conditions such as acid leaching, thermal treatment and chemical processing. Different treatments are aimed to increase K availability which is related to the modifications in mineralogical composition. The modifications in the feed sample and treated samples are studied through SEM-EDAX, XRD, EPMA and optical microscope. With the combination of treatments, it is possible to extract more than 90% K and the formation of sylvite phase (water soluble) confirms the dissolution of potash values."

Jan 1, 2016

By M. B. McClenaghan

"Abstract - The Matheson area of northeastern Ontario is of great interest for mineral explo­ ration because of its geological similarities with the adjacent Timmins, Kirkland Lake and Larder Lake gold camps. Exploration in the area, however, is hampered by the presence of an extensive and thick cover of glacial sediments. For this reason, till geochemistry has be­ come an important exploration method. The Ontario Geological Survey&apos;s Black River -Matheson (BRiM) reconnaissance till sampling project, carried out between 1984 and 1988, was designed to aid exploration in the Matheson area by documenting the Quaternary stratigraphy and providing a database of till geochemistry. Till samples were collected by backhoe trenching of surface pits in areas of thin drift ( < 5 m) and by sonic overburden drilling in areas of thicker drift. This paper summarizes the results from the shallow till sampling component of the BRiM project.Two hundred and eighty-two surface samples were collected from Matheson Till, the youngest till sheet in the area, which was deposited during the Late Wisconsinan. For each sample, the non-magnetic heavy mineral (>3.3 S.G.) and fine (-250 mesh) till fractions were analyzed geochemically. In addition, visible gold grains were recovered by panning the heavy mineral fraction. Five areas that display multi-element anomalies in both till fractions warrant further investigation: (1) western Egan Township, overlying the Bradley Lake Syenite; (2) around and south of the Munro and Croesus mines, in Munro and Guibord townships; (3) central Garrison Township overlying the Garrison Stock; (4) south of Ore Car Lake in northern Thackeray Township; and (5) southeastern Harker Township. In these areas, Matheson Till has a local provenance and the bedrock sources for these anomalies are nearby in the up-ice (north­ northwest) direction. Due to the fine-grained nature of gold in bedrock deposits in the BRiM area, the small size of most gold grains recovered from till samples (<50 1-1m) and the variable distribution of gold in the heavy mineral concentrate and fine fractions, the fine fraction in addition to the more commonly used heavy mineral concentrate should be used for gold exploration.Surface till samples have been affected by weathering to a depth of s3 m. Weathered till is characterized by a very low carbonate content in the matrix fraction, the absence of sulfide grains in the heavy mineral concentrate and higher concentrations of copper, nickel and zinc in the fine fraction than in the heavy mineral concentrate. As a result of the weathered/ oxidized nature of the surface till samples, the fine fraction is a better sampling medium for base metal exploration."

Jan 1, 1992

By G. I. Mathieu, R. W. Bruce

Flotation schemes for the separation of molybdenite from other minerals are based on utilizing the Inherent hydrophobicity of molygdenite (Fuerstenau1). This natural floatability was attributed to the crystalline structure of molybdenite by Gaudin et al.2 who suggested that any surface formed by the rupture of van der Wall's bonds should be hydrophobic and, therefore, naturally floatable. Other authors argued that "natural floatability" is dependent of adsorption of hydrocarbon ions and/or molecu1es on the surface of the minerals. This theory, albeit-c questioned 1,2 has long been recognized in actual practice of molybdenite flotation as the latter in carried out with hydrocarbons, such as fuel oil, kerosene and stove oil. Although conferring ready floatability to molybdenite, these presents generally have little effect on other sulphides and silicates. However, talc is a noteworthy exception because of its innate floatability4. Not withstanding the reason for this behavior which has also been attributed to crystal structure2 its end results as in the case of molybdenite is an immediate flotation response to frothing oils arid kerosene, as was observed by Baranovski5, Sutherland and Wark6.

Jan 1, 1974

"The gravimetric dust sampler is one of the tools now available to the industrial hygienists for determining the worker &apos;s exposure to the numerous types of particulate matter that may be present in the workplace. The paper &apos; reviews the different sampling trains that can be used for the two major criteria for respirable dust and some of the sources of error in this dust assessment technique.IntroductionIt may be stated simply that the measurement of airborne dust in the working environment is done for one or two reasons: namely, for engineering control purposes and! or to evaluate the potential for toxicological insult arising from the inhalation of dust particles.This paper reviews the progress made in the development of dust-assessing instruments, particularly the gravimetric types designed to meet British and U.S. dust criteria , and discusses the limitations in their use for this purpose."

Jan 1, 1981

By M. B. McClenaghan

"The Matheson area of northeastern Ontario is of great interest for mineral exploration because of its geological similarities with the adjacent Timmins, Kirkland Lake and Larder Lake gold camps. Exploration in the area, however, is hampered by the presence of an extensive and thick cover of glacial sediments. For this reason, till geochemistry has become an important exploration method. The Ontario Geological Survey&apos;s Black River-Matheson (BRiM) reconnaissance till sampling project, carried out between 1984 and 1988, was designed to aid exploration in the Matheson area by documenting the Quaternary stratigraphy and providing a database of till geochemistry. Till samples were collected by backhoe trenching of surface pits in areas of thin drift (< 5 m) and by sonic overburden drilling in areas of thicker drift. This paper summarizes the results from the shallow till sampling component of the BRiM project.Two hundred and eighty-two surface samples were collected from Matheson Till, the youngest till sheet in the area, which was deposited during the Late Wisconsinan. For each sample, the non-magnetic heavy mineral (> 3.3 S.G.) and fine (- 250 mesh) till fractions were analyzed geochemically. In addition, visible gold grains were recovered by panning the heavy mineral fraction. Five areas that display multi-element anomalies in both till fractions warrant further investigation: (1) western Egan Township, overlying the Bradley Lake Syenite; (2) around and south of the Munro and Croesus mines, in Munro and Guibord townships; (3) central Garrison Township overlying the Garrison Stock; (4) south of Ore Car Lake in northern Thackeray Township; and (5) southeastern Harker Township. In these areas, Matheson Till has a local provenance and the bedrock sources for these anomalies are nearby in the up-ice (north northwest) direction. Due to the fine-grained nature of gold in bedrock deposits in the BRiM area, the small size of most gold grains recovered from till samples (< 50 um) and the variable distribution of gold in the heavy mineral concentrate and fine fractions, the fine fraction in addition to the more commonly used heavy mineral concentrate should be used for gold exploration.Surface till samples have been affected by weathering to a depth of = 3 m. Weathered till is characterized by a very low carbonate content in the matrix fraction, the absence of sulfide grains in the heavy mineral concentrate and higher concentrations of copper, nickel and zinc in the fine fraction than in the heavy mineral concentrate. As a result of the weathered/ oxidized nature of the surface till samples, the fine fraction is a better sampling medium for base metal exploration."

Jan 1, 1992

By R. Frank Chiappetta, E. B. Wilson

"The maintenance records for AL-60 airlegs at Falconbridge Ltd. are used to demonstrate some of the procedures for the analysis of such data.The data are not representative of pure failure s of one type or another. In fact, the records are for the undefined pseudo-failures which are usually found in industrial operations. However, because the machines are brought to the shop only when inoperative, the individual recorded components are treated as failures. Manual calculations are conducted to show the analysis of variance (ANO VA) approach to determine whether certain data can be combined; only a limited number of the 206 machines being considered. The manual procedures continue with the weighting of the suspensions; i.e. terminations f or reasons other than the failure of the given component. After the data are sequenced in the proper order, the nature or pattern of the data is determined using the Kolmogorov-Smirnov (KS) test.It is recognized that these manual examples must be replaced by compute r methods 10 process voluminous data of this nature. Such programs are developed and available. However, a program called RELCODE is used in this case to correspond to the manual examples and to take into account the suspensions. These analytical procedures form the basis for those studies required for good maintenance management."

Jan 1, 1985

Adaptive processing is often related to the mineral composition of the mining block currently processed. The portions of waste, ore and secondary product minerals considered are always positive and typically sum to 100% (i.e. a composition). A typical solution to predict block averages of spatially dependent quantities would be block kriging. However, kriging is based on spatial correlations and it has been repeatedly shown that correlations of compositional data are spurious and blurred by the constant sum constraint. Aitchison (1982) proposed a general solution for compositional problems, based on transforming the compositional data to a set of logarithms of ratios of components, and analysing the transformed scores. The transform is chosen to be invertible to ensure that no information is lost in the process. This methodology avoids spurious correlation problems and ensures coherence between results obtained with different subcompositions. Pawlowsky-Glahn and Olea (2004) adapted the approach for point-support geostatistics, allowing the prediction of point compositions from spatially neighbouring data, without the artefacts induced by standard multivariate cokriging. Unfortunately upscaling the results of this approach with block cokriging is not straightforward, because of the nonlinearity of logratio transforms. Furthermore, we have to consider those nonlinearities created by the dependence on the block composition of extraction efficiency and processing costs of the possible processing choices. This paper proposes a solution for predicting the conditional expectations of the benefit of processing the block with each processing choice using geostatistical simulations of the local values of the composition and the resulting block integrals. The computation for a large number of blocks can be done efficiently using Cholesky decomposition. The approach also allows the calculation of prediction errors for expected compositions and expected benefit at almost no additional computational cost. Such compositional approach is necessary, for example when processing choices depend on proportions of certain minerals after other components have been removed; or if processing alters the composition in a multiplicative way, by partially removing a portion of some components.

Aug 1, 2013

By Mike Anderson

The annual budget for the repair and maintenance of equipment at Syncrude Canada Ltd is in excess of 450 million dollars. Of this amount, a significant portion can be attributed to the loss of material on various pieces of equipment throughout the operation. In order to effectively battle the different wear and corrosion mechanisms that lead to material loss, it is important to understand how materials behave in the environments in which they are used. Through the work carried out at Syncrude, and work conducted with various external collaborators, significant improvements in both equipment reliability and productivity have been achieved. This paper will review some recent field trails where materials research has demonstrated the potential for significant improvements in equipment run life and reduced maintenance costs. These field trails will demonstrate the need for understanding the interaction between various damage mechanisms and the materials used in different services. The paper will also discuss current areas of focus along with future directions for further work.

May 1, 2003

By Roger J. Goodman

"Major industrial restructuring, which started to manifest itself in the mature economies of the Western World and Japan in the 1970s, will accelerate in the 1980s and 1990s. Conventional heavy manufacturing industries will continue to lose ground to lighter processing/assembly operations and the new wave of high technology, information and service sectors. The decline in heavy manufacturing has severely impacted on the steel industries of Western Europe, the U.S.A . and Japan.World trade in metallurgical coal has shifted correspondingly, with declining demand in the mature developed countries being only partially offset by large increases in the steel intensity of the newly-industrialized countries (NICs) of the Far East, Latin America and, to a more limited extent, the Middle East and Africa. These trends will be accentuated in future years with direct implications for the distribution of metallurgical coal trade. This paper discusses, in quantitative terms, such changes in the 1980s and 1990s, and examines the implications for, and impacts on, Canadian metallurgical coal exporters.IntroductionThe twenty-year period from the early 1950 s to the early 1970s was characterized by inexorable growth in consumer demand and industrial expansion in most of the advanced countries of the western world. Long- term forecasting during this period typically used linear extrapolation techniques which , despite their simplicity, invariably ended up predicting future demand and production level s with uncanny accuracy. Times have changed!The last decade has been characterized by a n abysmal failure of our economies to respond to simple long-term, linear growth patterns. We appear to have entered a new world in transition, where we can observe a wave of dying or sunset industries reluctantly being submerged by a wave of emerging or sunrise industries.This paper is aimed a t examining the evidence for long-term industrial restructuring trend s. For want of a better word, these so -called, megatrends are then used to predict future demand level s and spatial distribution of steel development and , hence, metallurgical coal trade. It is tempting to correlate the decline in economic activity in the western world with the first Organization of Petroleum Exporting Countries&apos; (OPEC) crisis of 1973. This crisis was probably no more than the straw that broke the camel&apos;s back, as the megatrends and embryo s of major industrial restructuring were already evident. Today these megatrends are merely more apparent and transparent than they were ten years ago.While the concept of industrial restructuring is the new economic buzz word, the process was at work, to a lesser degree even throughout the period of strong economic growth of the post-Second World War boom. Many people still remain convinced that our present-day sluggish economy is just part o f the typical , though rather more prolonged, recessionary cycle. Yet, we have always been part of a dynamic economic system and industry throughout history has been the subject of a continuous process of evolution, restructuring and reconstitution . Now the time is ripe to examine the evidence for such restructuring in order to develop coherent policies of adjustment in this transition from one industrial regime to another."

Jan 1, 1985

By G. H. Hope, A. R. Maycock

"La Mine Doyon is a gold mining operation located in northwestern Quebec, approximately 35 km east of Rouyn-Noranda and 85 km west of Val d&apos;Or. The mine is jointly owned by Lac Minerals Ltd. and Cambior Inc. with Lac Minerals as the manager. Production statistics as of February 1987 are 6.4 million tonnes milled at an average grade of5.8 g/t Au. Current reserves of9.9 million tonnes at 5. 7 g/ t Au to a depth of400m have been outlined. Indicated reserves below this horizon could considerably increase this reserve.The mine currently consists of two open pit and two underground mine operations, producing approximately 3600 tonnes per day of ore at an average grade of6 g/t. The ore is currently processed at the La Mine Doyon mill at a rate of1400tid and at Lac&apos;s East Malartic mill at 1950 t/d. Ore is also processed intermittently at Lac&apos;s Les Terrains Auriferes mill and at Noranda&apos;s Horne Division.La Mine Doyon is currently in the midst of a program to expand and upgrade the mill at La Mine Doyon. The expansion to 3000 t/day includes the conversion of the existing crushing and grinding circuits to a SAG (semi-autogenous grinding) mill circuit and the existing filter wash plant to a CIP (carbon-in-pulp) recovery plant. The economics of this project are based on reduced operating costs (milling and trucking) and improved recovery due to updated technology. HistoryThe area between Noranda and Val d&apos;Or has a long history of mining activity in both base metals and gold, dating back to the early 1930s. More recently, several new orebodies have been discovered and exploited in the area including La Mine Doyon, Lac&apos;s Mine de Bousquet, Dumagami, and the Kiena operation.La Mine Doyon was discovered in the early 1970s, and brought into limited production in late 1979. The mine was started on are reserves of 2.75 million tonnes at 6.2 g/t and was, thus, considered a small, short-term operation. Mining started at an initial rate of 550 tI d with all the ore being shipped to Noranda&apos;s Horne smelter as flux. When Lac&apos;s East Malartic mill became available for custom milling, Doyon commenced shipping to that facility at a rate of 650 t/d. As a result of some equipment additions and an improved understanding of the ore, the East Malartic mill throughput was gradually increased from 650 t/d to the current rate of 1950 t/d."

Jan 1, 1988

By R. Stauber, B. Friedrich, S. Hilgendorf, G. Homm, C. Gellermann

Due to recent regulations limiting tolerated lead concentrations in copper alloys, new recycling strategies have to be considered. This study investigates the suitability of technical approaches in order to recycle leaded copper alloys exemplified by CuZn39Pb2 and produce an alloy in compliance with future lead regulations in the European Union. Three pyrometallurgical methods are considered to achieve this goal, namely vacuum distillation, intermetallic precipitation and fractional crystallisation. The impact of essential process parameters i.e. pressure, temperature, time, atmosphere and quantity of additives are identified using thermochemical and kinetic modelling. An experimental implementation reveals a general suitability of all three refining processes. However, the individual efficiency of the different methods strongly differs. Thus, a detailed assessment is carried out in order to provide an evaluation on the efficiencies of these methods from a technological, economical and environmental point of view. Taking a possible industrial realisation into account, the authors recommend the approach of vacuum distillation, although the energy demanded is comparatively high due to the enthalpy of evaporation for zinc, or rather, lead. However, required lead concentrations can be reached quickly without introducing an external element to the material. The prediction of selectivity and evaporation speed, which are immanent variables for a successful implementation, can be validated experimentally. INTRODUCTION In 2016 approximately 1 million tonnes of leaded copper alloy semi-finished goods with an average lead content of 2.1 Ma% have been produced in the European Union (EU). The global production in the same period exceeded 5.5 million tonnes, while the lead concentration has stayed constant at around 2.4 Ma% for the last 50 years. Up to 80 % of the current production volume is covered with end-of-life scraps, which are used for direct re-melting, depending on the alloy composition. Lead has been a popular alloying element in copper alloys in general, and in particular in brass due to its positive impact on various mechanical, physical and chemical properties, especially machinability. Health and environmental concerns were drivers for many governments to implement limitations on lead. In order to further utilise the resource potential of leaded copper scrap, it is inevitable to develop methods to efficiently eliminate lead from circulation as far as possible. (Glöser, Soulier, & Tercero Espinoza, 2013; Soulier, Glöser-Chahoud, Goldmann & Tercero Espinoza, 2018)

Jan 1, 2019

By G. K. Rutherford, G. W. Van Loon

"Tailings in the mining and smelting industry are reject products of the refining process which are deemed too deficient in native are to warrant smelting. They are essentially finely ground rock materials which have been moved by alluvial suspension from the site of crushing to a deposit site. It is realized that components of flotation chemicals used in specific gravity separation may become part of the tailings and also that sewage sludge or other materials may be added at some stage to the tailing deposits.It would seem, then, that as tailings have a similar parent material to soils, namely rocks, and that they have also been comminuted to similar size fractions, they would react in similar ways to soils. There is an increasing body of evidence and experience which both supports and negates this supposition. It is the object of this paper to point out similarities and contrasts between these two materials which may influence the vegetation and rehabilitation of tailings.Soil-Formlnq FactorsThere are considered to be six soil-forming factors which impart the particular and unique properties harboured by a soil at any site. It is .relevant to consider each of these in turn, as each provides an historically based parameter with which to judge tailing properties.Parent MaterialsAlthough all mineral soils have originally come from rocks, for most soils the route has been rather circuitous. Soils may be formed directly from underlying rocks, as in some parts of tropical and semitropical regions today; these are sedentary soils. However, most soils of the world have been formed by materials which were transported to their present site by ice, water or wind, or as volcanic ash. Virtually all soils in Canada have been transported by ice or water and deposited on an extraneous rock surface during the last glacial retreat. Ice-deposited materials are extraordinarily heterogeneous in their size components and may range from very bouldery and gravelly to predominantly clay-sized materials. Water deposited sediments are usually homogeneous, but nevertheless these also show considerable level variations. In many parts of Canada, clay-sized materials deposited in ephemeral post-glacial lakes form the parent material for soils."

Jan 1, 1982

By T. Kalliomäki, A. T. Aji, M. Lundström, J. Aromaa

The settling properties of anode slime in copper electrorefining have crucial effect on copper cathode quality. Anode slime settling is affected by electrolyte composition and temperature, electrolyte circulation, and the sizes and density of the slime particles and agglomerates. Typically, the industrial copper electrolytes contain 40–60 g/dm3 Cu2+, 130–220 g/dm3 H2SO4, 0.04–25 g/dm3 Ni2+, 0.005–30 g/dm3 As, and have operating temperature of 55–70°C. In optimal electrorefining process, the settling rate of anode slime is sufficiently high to avoid the risk of getting the slime entrapped in copper cathodes. In this research the settling properties of copper electrorefining bottom slimes, mainly consisting of Cu, Ni, Ag, Se, Pb, As, Bi, Sb and Ba compounds, were studied by settling rate tests. The tests were conducted in water and synthetic electrolytes with known viscosities and densities. In addition, the effect of agglomeration was taken into account – it was observed that breaking the agglomerates which existed in the as-received slimes decreased the particle sizes on average 56–73%, which decreased the settling rate. The results of this study provide detailed information of anode slime settling and thus clarify the conditions causing cathode contamination risks in copper electrorefining. INTRODUCTION Settling rates of Cu-ER anode slimes affect the purity of cathode copper and faster settling rate decreases the contamination risk (Davenport et al., 2002; Shi & Ye, 2013). The settling rates are affected by the properties of anode slime particles (Wills & Napier-Munn, 2011; Aaltonen, 2014; Kiviluoma, Aaltonen, Aromaa, Lundström & Forsén, 2016) as well as viscosity and density of the electrolyte (Davenport, King, Schlesinger, Biswas, & Robinson, 2002; Shi & Ye, 2013). Thus, it is crucial to find out how the viscosity and density affect the settling rates. Small spherical particles with diameter below approximately 50 µm obey Stokes’ law (Equation 1) (Wills & Napier-Munn, 2011). v = gd 2 (ρS – ρF) (18η) -1 (1) where v is terminal velocity (m/s), g acceleration due to gravity (m/s2), d diameter of particle (m), ρS density of particle (kg/m3), ρF density of fluid (kg/m3), and η dynamic viscosity (Pa∙s). The approximate effects of kinematic viscosity (ν = η / ρS), density (ρS) and particle sizes on settling rates defined for small anode slime particles based on Stokes’ law are presented in Figure 1. However, Stokes’ law does not take into account other than spherical shapes, and it is only applicable for small particles. Consequently, the real settling rates of the particles are lower than these (Wills & Napier-Munn, 2011). Moreover, some of the anode slime particles are larger than 50 µm (Aaltonen, 2014).

Jan 1, 2019

By D. W. Heard

Electrospark Deposition (ESD) is a low heat-input, high energy density, micro-welding process. The short pulse duration and high-pulse frequency, in combination with the small amount of material transferred during each pulse, results in the evolution of extremely rapid cooling rates, believed to approach 105-106 °C/s [1]. This rapid solidification event results in the refinement of the microstructure to the nanostructured or amorphous level [2, 3]. Figure 1 displays the resultant microstructure of an Al-17%Si alloy deposited by the ESD process. Furthermore, it was determined that the microstructure of the deposit remained unchanged after subsequent layers were welded onto the presented layer. Freeforming of materials is a rapid prototyping process in which the deposited feedstock is built-up to the desired geometry in a near-net shape manner. Figure 2 displays the automated set-up employed produce three dimensional freeformed objects via multiple deposition trials of the ESD process. The automated XYZ table is equipped with CNC software to transform CAD renderings into three dimensional tool paths. Figure 3 displays an Al-12Si freeformed gear (2" diameter, 12 teeth) produced by the ESD process, prior to removal from the substrate. An SEM analysis of the freeformed component showed that the microstructure did not coarsen during the deposition of subsequent layers during the freeforming process, as depicted in Figure 4, resulting in the production of a bulk nanostructured component. This paper represents a summary of the capabilities of ESD to fabricate advanced materials possessing refined microstructure. In particular, results on the microstructural evolution obtainable for various wear-related systems will be presented. In addition, the feasibility of using the ESD process to freeform three-dimensional objects via multiple deposition passes will be presented and accompanied by a characterization of the properties of the freeformed component. [1] R. N. Johnson, "ElectroSpark Deposition: Principles and Applications," in Society of Vacuum Coaters, 2002, pp. 87-92. [2] J. Milligan, D. W. Heard, and M. Brochu, "Formation of nanostructured weldments in the Al-Si system using electrospark welding," Applied Surface Science, vol. 256, pp. 4009-4016. [3] S. Cadney and M. Brochu, "Formation of amorphous Zr41.2Ti13.8NilOCul2.5Be22.5 coatings via the ElectroSpark Deposition process," Intermetallics, vol. 16, pp. 518-523, 2008.

Jan 1, 2010

By M. Maldonado

This work details the application of a decentralized control strategy to a pilot flotation column working with a two-phase system (water-air). The process is represented by a multivariable system composed of three inputs and three outputs. The selected control variables are the froth depth, the air hold-up and the bias rate, whereas the corresponding manipulated variables are the set-points of the local flow controllers of tailings, air and wash water. All controlled variables are estimated using electrical conductivity based techniques. In particular, the results of a new method for estimating the bias rate, based on the measurement of the volumetric fraction of wash water under the interface, is presented. This method reduces the coupling problem associated to the bias estimation as a difference between feed and tailing water rates. Moreover, the nominal system transfer matrix can be represented by an upper triangular matrix, in such a way that the closed-loop system stability reduces to the stability of the independent control loops. The experimental results show that the closed-loop system performance, particularly that of the bias rate loop, is strongly dependent on the air flow rate, reaching in some cases the saturation point of the controller.

Jan 1, 2007

By Tim J. Carew, Dennis C. Martin

"One approach to stabilization of rock slopes is to place a buttress at the toe of the slope to provide additional resisting forces and increase the length and strength properties along the failure surface. This paper describes the rock mechanics and mine planning aspects of incorporating a buttress of intact rock in the lower part of the slope as part of the slope design for the south wall of the final pit at Cassiar Mine. Stability analysis techniques and results are described. Analyses results have indicated that, in order to maintain steep over-all slopes in the final pit, a buttress of intact rock shoud be incorporated into the lower section of the slope until late in mine life. The effect of the buttress is to flatten the slope and reduce the slope height thereby improving slope stability. The mining plans would be such that the buttress would be mined out during the last four months of mining when the consequences of instability would be least severe.IntroductionThe concept of using a buttress to stabilize slopes has been used in mining and civil engineering construction in may locations (Richards and Stimpson, 1977). Most buttresses involve placement of coarse rock fill timber cribs or other material as a load at the toe of an already unstable slope to provide forces which resist failure by counteracting driving forces and increasing the length and strength of the failure path.This paper describes the geotechnical and mine planning aspects of incorporating a buttress of intact rock in the design of the south wall of Cassiar Mine. The effect of an intact rock buttress is to flatten the slope and reduce the slope height, thereby improving slope stability. No actual construction is required other than normal excavation of the slope. The ""mine plans would be such that the buttress would be mined out at the end of mine life when the impact of instability would be less severe and additional ore might possibly be recovered from the slopes. Mining of the buttress could induce instability at the very end of mine life at a time when maximum ore extraction has been achieved."

Jan 1, 1986