Search Documents

By T. G. Joseph, A. Sharma

ABSTRACT: Ultra-class haul trucks operating in oil sand face operational and maintenance issues as a result of soft underfoot conditions (Joseph, 2002). With exposure to frequent high g loading events, tire life is reduced due to sidewall belt fexure and frequent ground contact. Therefore, an improved under-standing of the interaction between tires and oil sand is needed. This paper examines the outcomes of a series of static and cyclic loading tests, performed using a scale tire on rigid, sand, and oil sand surfaces. Geometric predictions are made regarding the footprint area and vertical deformation of an ultra-classtire on similar surfaces.

Jan 1, 2011

By V. Murugaiyan

The Geotechnical Engineer is faced to view problems emerging from the task of protecting the environment and also the problems related to prevention of natural hazarders. Geo-Environmental Engineering, based on the development of geotechnical engineering, addresses the problems for the industrial world and the impact on health and welfare in relation to pollution of the ground. In the recent years, acute land pollution due to indiscriminate discharge of industrial effluents especially Organic acid based effluents has become one of the major concern due to erosion in the privatization of sustainable development under Indian Scenario. To study the effect of chemical changes on soil properties due to amino acid effluent contamination on soil and erosion behavoiur. The changes in the soil properties of effluent contaminated clay and silty soil were experimentally observed to be due to the interaction of organic and inorganic constituents of effluent on index properties of soil. The surface reactivity of soil mass is experimentally reported to be varying proportionately with respect to clay (%) in the soil. Also higher surface reactivity of clay increases the Solid Retension Time (SRT) with increase in rate of chemical transformation of organic and inorganic solids within soil. Hence soil S1 (high clay content 54.5%) showed increased SRT and soil S3 (low clay content, high silt and clay content 94.9%) showed decreased SRT and long transformation stage.

May 1, 2004

An optimization process is described that can be systematically applied by mine planners to produce life-of-mine schedules aligned with their strategic targets, while maximizing the net present value of the mining operation. The software tool employed uses heuristics and an evolutionary algorithm to generate life-of-mine schedules of production and development activities. Generating such schedules is typically a very difficult task due to the large number of operational constraints that must be respected, and the vast number of alternative schedules; as a result the value of the mining operation can be compromised. With an expansion at Newmont?s Leeville mine in Nevada, the mine planners were given the task of producing feasible life-of-mine schedules with significantly increased production rates. Their initial efforts indicated that it would be a considerable challenge to generate such schedules in a timely manner. By systematically applying the proposed optimization process, the mine planners were able to generate optimized life-of-mine schedules with the desired production rate.

Aug 1, 2013

By Frank Cappuccitti, James A. Finch, Stéphanie Gélinas

"A colorimetric technique, originally developed for methyl iso butyl carbinol (MIBC) based on the Komarowsky reaction, has been extended to a wide range of common mineral flotation frothers. The procedure, which is briefly described, is shown suited to on-site determinations in a campaign at Kennecott Utah Copper Copperton Concentrator (Rio Tinto). Some observations are described, including: frother (MIBC) concentration evolution down a bank, frother distribution between pulp and froth phases, and loss of frother over time due to adsorption on certain minerals. A possible interference with a fuel oil addition was overcome. MIBC in recycle water was also measured.The ability to monitor frother easily will help interpret gas dispersion behaviour and should permit further optimization of flotation cell hydrodynamics and chemistry. The capability to directly measure should help optimize the type, amount and location of frother addition, and to assess frother recycled with reclaim process water.INTRODUCTIONOwing to the lack of analytical methods, the task of determining frother concentration in plant flotation circuits is not routinely performed. Industrial sites seldom outsource analyses that are both costly and inconvenient, due to the necessity of shipping freeze-dried samples to remote testing facilities. A more direct colorimetric method has recently been demonstrated for the laboratory characterization of common industrial frothers (Gélinas and Finch, 2004). The approach, based on the Komarowsky reaction (Penniman et al., 1936; Coles et al., 1942; Duke, 1947), was previously described by Parkhomovski et al. (1976) for methyl iso butyl carbinol (MIBC). The reaction involves the interaction of the OH group of a higher alcohol, concentrated sulphuric acid, and salicylaldehyde, to yield coloured solutions with intensities that can be analyzed by UV-visible spectrophotometry."

Jan 1, 2005

By Andre L. De Vegt, Cees J. N. Buisman

"For the past eight years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Metal and sulfate can be removed from mine waters using two biological steps:1. Sulfate reducing bacteria convert sulfate to hydrogen sulfide (H2S). The H2S reacts with the dissolved metals to form insoluble metal sulfide precipitates.2. Sulfide oxidizing bacteria convert excess H2S to elemental sulfur.Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove metals and sulfate as described above. The system has been operating since May 1992 treating a flow of 5000 m3/d. A test program, utilizing a large scale pilot plant, will commence in November 1995 at a copper mine in the U.S.A. to remediate groundwater contaminated with sulfate and heavy metals. Biological reactor performance and selective metal recovery will be studied. Sulfur dioxide (S02) can be removed from fluegas using a combination of scrubber technology and the two biological steps. The end product is elemental sulfur. A commercial size biological desulfurization plant has been in operation since July 1994 treating 50,000 Nm3/h of fluegas. Sulfide can be removed from mining waters or anaerobic wetlands using a THIOPAQ® Sulfide Oxidizing reactor.lntroductionSulfur can be present in various water and gaseous streams in a mining operation. In many cases the sulfur compounds have to be removed because of toxicity, corrosive properties and contribution to acid rain. Mine waters can contain dissolved heavy metals. An efficient way to remove dissolved metals removal is the precipitation as metal sulfides. Paques has developed and installed treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. These treatment systems biologically convert sulfate to hydrogen sulfide (H2S) which can be used in heavy metal precipitation. Excess H2S is biologically converted to elemental sulfur. This paper provides an overview of these newly developed biotechnological treatment systems."

Jan 1, 1997

By Xiaoqi Sun

"Rare earth elements (REEs) have a series of specific properties making them invaluable in products including lighting, electronics and magnetism. The elements have been used in many commercial products, for example, turbines, electric vehicles, batteries, lighting, computers, cell phones and lasers. Heavy REEs are attracting the interests of scientists from many countries, and these elements have become critical to develop high-tech materials. Ion-adsorbed rare earth deposits were first discovered in China. The minerals are also called weathered crust elution-deposited rare earths. The particular types of deposits are distributed throughout southern China. The ion-adsorbed deposits are rich in medium and heavy REEs, accounting for more than 80% of the world’s total medium and heavy REEs production. However, the separation of heavy REEs from ion-adsorbed deposit is difficult owing to their similar chemical properties. The conventional separating technologies have caused serious pollution. A novel extraction strategy has been developed in this laboratory and is presented herein.INTRODUCTIONThe unique properties of rare earth elements (REEs) render them important in high-strength magnets, lighting phosphors, polishing compounds, and ceramics. Especially for applications that take advantage of the f-orbital electrons, substitutions outside the REE family are often difficult to impossible (Nassar, Du, & Graedel, 2015). Extracting and separating individual elements from mined ore is not easy, requiring lengthy operations to separate them, and this results in high costs and adverse effects on the environment. The low concentration of REE in the earth’s crust makes economic exploitation difficult (de Boer & Lammertsma, 2013) and the sustainability of the REEs separation industry has aroused considerable attention (McLellan, Corder, Golev, & Ali, 2014). To eliminate protons and break the dimmers in organic phosphonic acids or carboxylic acids, the saponification of acidic extractants by acid-base neutralization reactions are widely used in industrial REEs separation (Sun, Luo, & Dai, 2012a). The saponification procedure contributes to increased extractability and selectivity of acidic extractants to a considerable extent. The common industrial saponification mechanisms and technological processes are shown in Figure 1 and include ammonium saponification (saponified by NH3·H2O), sodium saponification (saponified by NaOH), calcium saponification (saponified by Ca(OH)2), and magnesium saponification (saponified by MgO). These inevitably result in wastewaters containing NH4 +, Na+, Ca2+ or Mg2+ because of the cation-exchange extraction mechanisms (Xiao, Long, Huang, Feng, Cui, & Wang, 2013; Song, Fu, Wang, Liu, Zhou, & Li, 2014; Sun & Waters, 2014)."

Jan 1, 2016

By H. E. Frimmel

Most of the gold in the Late Archean Witwatersrand Basin is of detrital origin but, in its present form, it is metamorphosed. The only relict detrital features preserved are the morphological characteristics of some placer gold particles. Regional burial metamorphism in the shallower and deeper levels of the Witwatersrand Supergroup reached temperatures around 300°C and 350°C at pressures between 2 kbar and 3 kbar, respectively, estimated from phase relations, chlorite-chloritoid exchange thermometry and chlorite thermometry. Metamorphism of the gold involved compositional homogenization of individual gold particles and partial recrystallization. Various infJ.1tration events caused the partial mobilization of the gold at slightly lower temperatures, between 240°C and 300°C. These infiltrations can be related to crustal extension during the deposition of massive carbonate sequences of the Transvaal Supergroup (around 2.5 Ga), and later to the emplacement of the Bushveld Complex, and to the Vredefort event around 2.0 Ga ago. The mobility of the gold was dependent on the sulfur fugacity prevailing in a particular horizon which, in tum, was determined by the amount of pyrite (and other sulfides) present in that horizon. With the sulfur fugacity being controlled by stratigraphy, low fluid rock ratios in a pyrite-rich horizon were most conducive for the mobilization of the gold. Thus, long-range gold mobilization in the Witwatersrand Basin can be expected to be the exception rather than the rule.

Jan 1, 1994

By L. A. Mells

"A laboratory test program was initiated by the Department of Energy, Mines and Resources as part of the National Uranium Tailings Program to investigate the applicability of a radium selective ion exchange complexer for removing radium from Canadian uranium mining effluents. The test program was carried out by Melis Consulting Engineers Ltd. under contract to the Department of Supply and Services using the Saskatchewan Research Council facilities located in Saskatoon, Saskatchewan.The results of this work showed the ion exchange complexer, Dowex XFS 43230.00, to be efficient in removing radium from contaminated water of uranium mining operations with the ultimate loading capacity of the resin on one type of water treated being determined as approximately 1,600 Bq/cm3 of new resin. Although this resin has potential application for treatment of effluent streams in uranium operations it has been identified that the resin efficiency and capacity is directly related to the chemistry of the water being treated and site-specific testwork is required in order to establish reliable design data for full-scale operations.IntroductionThe possible applicability of a radium-selective ion exchange complexer for removing radium from Canadian uranium mining effluents had been identified and discussed as a possible alternative to present radium removal methods during a review of disposal technology options for the National Uranium Tailings Program of the Department of Energy, Mines and Resources(1). Work by other workers(2.3) had shown the complexer to be very efficient in removing radium from contaminated water. Also, plant trials on contaminated minewater at the Mt. Taylor uranium mine in New Mexico is reported to have shown the resin complexer to be efficient under plant operating conditions.As a result, a laboratory test program was initiated by the Department of Energy, Mines and Resources as part of the National Uranium Tailings Program to investigate the suitability of this resin for Canadian uranium mining effluents. The test program was carried out by Melis Consulting Engineers Ltd. (MCEL) under contract to the Department of Supply and Services using the Saskatchewan Research Council (SRC) facilities located in Saskatoon, Saskatchewan."

Jan 1, 1985

By W. W. Bake

INTRODUCTION IN IN JUNE, 1943, the main pillars of the Beattie Mine glory hole failed, allowing over a million yards of wet clay and debris to flow into the mine, completely filling all workings to within seventy feet of the 3rd level. The resulting Job of clearing these workings and rehabilitating the mine represents a unique and hazardous operation, seldom, if ever, previously encountered in Canadian mining. The purpose of this paper is to describe one phase of this operation -that of cleaning and rehabilitating the mine from the 6th to the 9th level -to outline briefly the events which led up to this work and to describe the techniques and costs involved. It will be noted that such costs, methods, and performance figures as are dealt with in this paper refer only to work in the internal shaft and adjoining workings from the 6th to the 9th level, previous work having been done under other supervision and management. The Beattie mine is in Duparquet township, northwestern Quebec, twenty miles northwest of the town of Noranda and twenty-three miles southeast of the town of La Sarre. The mine and the town of Duparquet, which it?supports, are accessible by highway from Noranda throughout the year. Production at the Beattie mine began in May, 1933, and up to June, 1943, twenty-one million dollars in gold and silver had been recovered from five and a half million tons of ore.

Jan 1, 1951

By P. L. Li, B. X. Song, C. H. Wang, T. Wang, Z. Hu

"The treatment of an oxidized copper-gold ore by stage cyanide addition was investigated. For cyanidation, free cyanide ion concentration can be an indicator of whether there is copper dissolved in cyanide solution, and maintaining the free cyanide ion concentration lower than 1.0 g/L could be an effective way to prevent copper dissolution and reduce cyanide consumption. For that purpose, stage cyanide addition was introduced to control free cyanide ion concentration within the range from 0.8 to 1.0 g/L. Cyanidation tests results indicate that gold extraction was still acceptable at reduced cyanide consumption with a lower copper extraction. Based on the experimental study, industry application works at Beiya concentrator of Yunnan province, China were successfully conducted. When the raw ore contains 2.95 ppm Au and 0.75% Cu, by stage cyanide addition method, the gold extraction was still 93% at reduced cyanide consumption of 2135 g/t, which was only half of one addition method, and the copper extraction dropped to only 5%, which indicated that dissolution was prevented for almost 75% of the malachites.INTRODUCTIONCyanide with its competency to form a strong complex with gold, is the most preferable lixiviant for gold leaching. However, cyanidation is not inherently a selective process since many other minerals present in the ore are also readily soluble, especially the copper minerals. Muir (2011) reported that every 1% reactive copper present in the ore consumes about 30 kg/t NaCN, which can have detrimental effects on the process efficiency and economics due to high cyanide consumption, reduced gold leach rates and poor gold recovery."

Jan 1, 2016

By Raymond D. Potts

"Minntac is a taconite mining, concentrating and pelletizing operation located near the town of Mountain Iron, Minnesota, U.S.A. It is totally owned and operated by USX Corporation and represents its largest source of domestic iron units. Minntac began producing fluxed pellets in 1988 and has produced both acid and fluxed pellets since then. This paper compares the acid and fluxed pellets produced at Minntac. It reviews modifications that have been made to the plant flowsheet and discusses areas recognized for improvement since the beginning of fluxed pellet production. It also comments briefly on the performance of Minntac fluxed pellets in USX blast furnaces and the future of fluxed pellets at Minntac.IntroductionMinntac was built in three steps with each step designed to produce 6 million long tons of acid pellets per year. The actual production has varied though. Figure I shows the production by year at Mirmtac. Step I began production in 1967, Step 2 in 1972 and Step 3 in 1978. Mirmtac produced 16.5 million tons in 1979 but only 3.5 million tons in 1982 when the facility was shut down for six months because of the lack of demand for pellets. Since the initial start up, Mirmtac has produced over 200 million long tons of pellets. Until 1987, all the pellets produced were ""acid"" pellets. In 1987, equipment to produce ""fluxed"" pellets was installed and tested. In 1988, full scale production of fluxed pellets began."

Jan 1, 1991

By Marc C. Bétoumay

Workplace safety, health, climatic conditions and rising oil prices are aspects that are important to the mining industry. The need for cleaner energy for underground mine vehicles is requiring serious consideration. A number of alternate energy systems offer clean solutions to diesel emissions while maintaining the current liberty of vehicle movement. This watershed article provides a broad comparison of cleaner diesel and alternative energies for underground production vehicles. Most alternate energies and clean diesel have already been tested in underground production vehicles. There are no technology gaps that would prevent the development of commercial alternative energy power plants, but in the case of alternate energies, second and third generation versions will be required to fully test for safety and operation viability. Full regulatory development is also required and could be done in parallel to power plant testing. Vehicle operation and maintenance manpower would be the same for alternate energy application as for clean diesel. Capital cost for alternate energy power plants will remain higher until the medium term. Owing to significant ventilation savings possible with alternate technologies, operating costs would be reduced.

May 1, 2011

By T. Marolt, J. Likar, E. Grøv, J. Žarn

"Underground structures are an integral part of the infrastructure of modern society and are used for a wide range of applications, including subways and railways, highways, not at least nuclear facilities. When the wider area is subject to earthquake activity, underground constructions should be analyzed on seismic and static loading. Observations showed that the underground structures have significantly less seismic risk than surface structures. Available methods allowed analyzing the magnitude of risk for different input parameters of seismic loads in different ground environment. Simulation of earthquake loading on underground structures, in the present paper is given the various aspects of analyzing the potential damage and instability of underground facilities. INTRODUCTIONThe development of methods and computing resources used for para-seismic engineering has finetuned the evaluation of the seismic strength of buildings and equipment. Reinforcements may therefore be decided, not simply on the basis of a reassessment of the hazard, which constitutes input data for the calculation of structures and equipment, but also on the basis of developments in para-seismic engineering. Underground facilities are an integral part of the infrastructure of modern society and are used for a wide range of applications, including subways and railways, highways, material storage, and sewage and water transport and not at least nuclear facilities. Although in the past showed that the underground structures are significantly less seismic risk than on the surface, the professional researches and their results are accessible. Seismic resistance of underground structures is analyzed from several aspects. The currently available methods allowed analyzing the magnitude of risk for different input parameters of seismic loads in different ground environment. For better interpretation of earthquake loading on underground structures, are given below the various aspects of analyzing the potential damage and instability of underground facilities in rock. One of the early studies which covered this are of investigation were prepared by Dowding and Rozen (1978). They grouped damages due to earthquakes in underground structures into three main categories:- damage from ground shaking- damage from fault dislocation- damage by earthquake-induced ground failures (e.g. liquefaction and landslides)."

Jan 1, 2015

By H. Nejati

Experimentally, the Semi-Circular Bending Moment (SCB) fracture toughness test results of Basalt Specimens Under Illumination (BSUI) have shown reduction in fracture toughness and failure force as a result of micro-cracking. The fractographic investigation of BSUI confirms initiation and extension of micro-cracks. Determination of a relation between strength reduction (herein fracture toughness reduction) and density, location and orientation of thermo-mechanical induced cracks due to microwave radiation is critically important. Numerical modeling can bridge strength reduction and the density of thermal microcracks generated due to microwave radiation. Discrete Element Modeling (DEM) is a power tool for simulation of micro-crack initiation, coalescence into macroscopic fractures and failure mechanisms in brittle rock specimens under different stress regimes (herein combination of pure tensile stress due to SCB testing, and thermal stress due to microwave radiation). For this purpose, a DEM modeling of SCB testing of basalt using EDEM (i.e., a DEM based software). DEM models are calibrated according to results of experimental SCB testing as reported in previous papers. This paper first reviews some background data on SCB fracture toughness, and experimental results of fracture toughness of microwave treated SCBs. Then it proposes a new methodology for simulation and validation of rock samples exposed to microwave illumination with regard to experimental results, and discusses the correlation between fracture toughness of BSUIs and density of micro-cracks, which is attributed to applied microwave power and duration of illumination.

Aug 1, 2013

By A. R. Farkoosh, K. Korgiopoulos, McGill University, O. Rodop, L. A. Villegas Armenta

"New generation of Al-Mg-Si alloys with thermally stable dispersoids that prevent recrystallization and grain growth during hot deformation are currently used in automotive components requiring good formability. Alloy chemistry controls the phase formation especially age-hardening precipitates, dispersoids, and primary intermetallic which have pronounced effect on grain structure, strength and formability. In this work, thermodynamic calculations have been used to predict the effects of varying levels of Si (0.5-1.5wt%), Mg (0.5-1.5wt%) and Mn (0.1-2.5wt%) on phase selection. Thermodynamic calculations have been performed in equilibrium and non-equilibrium conditions via the FactSage™ software using the FTlite database. Selected compositions have been cast, heat treated, extruded and characterized through scanning electron microscopy with energy dispersive spectroscopy and electron channeling contrast imaging techniques. The calculations showed that at the hot deformation temperature of ~540 oC, exceeding certain Mg and Si levels would lead to retained *-Mg2Si intermetallics and Si particles at the grain boundaries in addition to a-Al-(Mn,Fe)-Si. It was found that retained *-Mg2Si phase which adversely affects formability can be avoided for Si+2Mg levels lower than 2.3wt%. FactSage calculations also showed that increasing Mn from 0.5wt% to 1wt% leads to an increase in the amount of dispersoids (from 1wt% to 2wt%) that can potentially slow down recrystallization and grain growth during hot deformation and improve formability. Calculations at room temperature also show that for an alloy with 0.7wt% Mg, excess Si beyond 0.7 wt% promotes the precipitation of Si clusters in the Al matrix that accelerate natural age-hardening. Results were confirmed by experimental investigation.INTRODUCTIONAluminum alloy 6082 (Al-Mg-Si) is used in the automotive industry because of its high strength, and good weldability (I. J. Polmear, 2006). The alloy is age-hardenable through the precipitation of ß-Mg2Si and its precursors, and the recrystallization is usually inhibited by Mn- and Cr-containing dispersoids formed through high temperature heat treatments (I. Polmear & Couper, 1988). However, it is known that minor changes in alloy chemistry (Mg/Si ratio) can have significant influences on the ductility and formability of these alloys by altering phase selection and the resultant microstructure (Gupta, Lloyd, & Court, 2001; McQueen & Celliers, 1997; Zajac, Hutchinson, Johansson, & Gullman, 1994). For automotive applications where wrought alloys (usually extrusions) are cold-formed to produce suspension components, the chemistry of the alloys and the extruded structure are of crucial importance as they determine the formability at room temperature (Asensio-Lozano, Suárez-Peña, & Vander Voort, 2014). In this study, thermodynamic calculations along with experimental investigations were carried out on the Al-Mg-Si system to understand their phase formation and precipitation hardening as a function of alloy composition."

Jan 1, 2016

By M. Xian, M. Jahazi, Y. L. Lin

The 2-mm butt joints of ZE41A-T5 sand castings were laser welded at different defocusing distances on two surface conditions (as-cast or machined) using a continuous wave 4 kW Nd:YAG laser system at a power of 2.5 kW and a welding speed of 6.0 m/min. Two welding modes (conduction or keyhole) have been observed. The adjustment of defocusing distance can greatly influence the establishment of conduction or keyhole modes. On the machined surface conditions conduction welding is obtained at a power density of 4.0 x 105 W/cm2. In contrast, keyhole welding is reached at a threshold irradiance of 1.5 x 106 W/cm2. Neither conduction nor stable keyhole modes have been established at a range of power density from 7.7 x 105 to 1.2 x 106 W/cm2 on the machined surface conditions. On the as-cast surface conditions keyhole is obtained at a power density as low as 4.0 x 105 W/cm2 but good surface quality is obtained at a defocusing of +2 mm. The as-cast surfaces require lower power irradiance for the formation of keyholes indicating that they have higher energy absorptivity for Nd:YAG laser beams probably due to coarse surface morphology.

Jan 1, 2004

By R. Loney, M. Militzer

There is a significant demand for new high strength steels with fine grain sizes for structural applications. One approach in this regard is to develop hot-rolled HSLA steels where refining the microstructure leads to increased strength levels, e.g. 700 MPa yield strength, that can be attained by suitable modifications of chemistry and processing. Here, an HSLA steel is investigated that contains 0.05wt%C-1.65wt%Mn-0.20wt%Mo¬0.07wt%Nb-0.02wt%Ti and approaches the above strength class. The ability to control and predict the mechanical properties of hot rolled steel depends strongly on the thermomechanical processes, which the steel undergoes. The final microstructure and, thus, the properties of the hot-rolled steel are a function of the austenite decomposition obtained during accelerated cooling on the run-out table and precipitation during coiling. The austenite-to-ferrite phase transformation under run-out table conditions has been investigated using a Gleeble 3500 thermomechanical simulator equipped with a dilatometer. The effects of cooling rate and initial austenite microstructure including the degree of work hardening on austenite decomposition kinetics and ferrite grain refinement have been quantified. Results show that grain refinement can be optimized by the presence of work hardened austenite and accelerated cooling. Based on the experimental results, a model is proposed to predict the transformation start temperature and the resulting ferrite grain size for run-out table cooling conditions.

Jan 1, 2004

By A. R. MacPherson

"This paper considers four aspects of autogenous grinding. Part 1 discusses statements on power efficiency of autogenous grinding compared to conventional crushing and grinding systems. It also demonstrates how high-power efficiency can be obtained from autogenous grinding systems. Part 2 considers a simple method of testing ores to determine the type of autogenous plant which can treat these ores on a commercial basis. A comparison of testing for simple small plants vs large plants or complex ores is included. Part 3 considers important aspects which have to be considered in proper design of an autogenous grinding system. Part 4 discusses problem ores and how they can be treated in an autogenous system. INTRODUCTIONAfter about 35 years of using autogenous grinding plants in the mining industry, it is perhaps time to review where we are with this, by now, relatively old development. Autogenous grinding in this paper means grinding run-of-mine ore by fully autogenous means or by using a ball charge to assist the grinding (semi-autogenous). Also, autogenous grinding can be eitherby dry or wet.The use of autogenous grinding in the fifties was making its slow start, and it was not until the sixties that more of the mining industry would consider its use . By the seventies, most builders of new plants would have considered autogenous grinding, whether they used it or not, in the final design.In the eighties, most large plants use autogenous mills and to reduce over-all operating costs, many older conventional plants are now looking and actually retrofitting these old plants with autogenous grinding mills.It is evident that many misconceptions concerning autogenous grinding are still current. Some come from improperly designed plants which result from poor test work. There are many considerations in the proper design of autogenous plants. Some ores have been found to give problems even in a well designed plant. These ore types are beginning to be classified and recognition in the test stage allows steps to be taken in the design so that these ores can be efficiently handled in autogenous grinding plants.Therefore, this paper will address the following aspects of autogenous grinding:1. Misconceptions regarding autogenous grinding.2. Testing of ores to ensure a well designed commercial plant.3. Important considerations in mill design.4. Difficult ores, their recognition and types of design to handle such ores."

Jan 1, 1989

By Jorge Amaya

A critical aspect of long-term open-pit mine planning consists in computing a production schedule based upon a block sequencing strategy. Such a schedule should specify when and if blocks should be extracted in such a way as to maximize NPV, while satisfying wall-slope and production capacity constraints. It is well known that this problem can be modeled with integer programming (IP). However, integer programming is not used in practice because the size of typical block models makes such problems intractable to standard IP solvers. In this article we describe a scalable IP-based methodology for solving very large (millions of blocks) instances of this problem. We show that embedding standard IP technologies in a local-search based algorithm we are able to obtain near-optimal solutions to large problems in reasonable time. This methodology has been tested in several mine wide block models.

Oct 1, 2009

By Jorge Amaya

A critical aspect of long-term open-pit mine planning consists in computing a production schedule based upon a block sequencing strategy. Such a schedule should specify when and if blocks should be extracted in such a way as to maximize NPV, while satisfying wall-slope and production capacity constraints. It is well known that this problem can be modeled with integer programming (IP). However, integer programming is not used in practice because the size of typical block models makes such problems intractable to standard IP solvers. In this article we describe a scalable IP-based methodology for solving very large (millions of blocks) instances of this problem. We show that embedding standard IP technologies in a local-search based algorithm we are able to obtain near-optimal solutions to large problems in reasonable time. This methodology has been tested in several mine wide block models.

Oct 1, 2009