Search Documents

By B. Daniels, A. Tieu, W. Yan, B. Ren, M. Vijay

"Plasma or thermal sprayed coatings are becoming more widely used in a wide range of industrial applications. The preference to use thermal sprayed coatings is mainly attributed to its superior wear, and corrosion resistant properties akin to hard chrome but without the harmful health implications of chrome in the coating process. Specifically, High Velocity Oxygen Fuel (HVOF) plasma sprayed Tungsten Carbide & Cobalt (WC/Co) coatings are presently being tested on aircraft landing gear. This coating can be efficiently applied and is highly resistant to corrosion and wear. However, HVOF coating's durability also makes it difficult to be stripped for inspection and overhaul. Current coating removal methods usually involve a multi-step process whereby the coating must undergo diamond wheel grinding, chemical dipping, grit blasting, ultrahigh pressure (UHP) 380 MPa (55 Kpsi) water blasting, and subsequent chemical dipping, depending on the type and thickness of the coating. As explained by Yan, et al [l]"" a unique method has been developed for removing HVOF coatings with the use of only water. The method consists of modulating a stream of water at a pressure of only 69 MPa (10 Kpsi) with ultrasonic waves to generate a forced pulsed waterjet. The resulting cyclic loading of the hard coating due to the impact of the water pulses easily causes it to flake off the substrate. This paper will briefly describe the fundamentals of the forced pulsed waterjet technique with an emphasis on insitu applications of the removal of various plasma and HVOF coatings."

Jan 1, 2006

By Wataru Inagaki, Kozo Kawano, Tetsuya Ando

Cu–Ni–P alloys are the typical precipitation-hardening material. Thus, Cu–Ni–P alloys is expected to apply alternative materials for heat-exchanger tubes. Therefore, it was investigated that the effect of the heat-treatment simulated brazing on mechanical properties of Cu–Ni–P alloy in this study. The hardness of specimen as heat-treatment simulated brazing after solution heat treated (sht) was shown approximately 105 HV. The peak hardness and tensile strength of the specimen as performed aged at 498 K for 43.2 ks following the heat-treatment simulated brazing achieved at approximately 140 HV and 260 MPa, respectively. From these results, it is expected the application to higher-strength tube for heat-exchanger after brazing in a furnace. INTRODUCTION Copper prices have increased dramatically with high in recent years. At the same time, manufacturing industries are required to reduce the environment load by reducing the wall thickness of the copper tubes used in heat exchangers. High-strength copper alloys are developed for reducing the wall thickness, while achieving high strength, of the copper tubes. Moreover, excellent workability and corrosive durability are also required by these copper tubes. Furthermore, the brazing, which are carried out at about 1050 K during the assembly process of heat exchangers, leads to grain growth and re-solving of additive elements. Nomura et al. achieved a tensile strength and Vickers hardness of approximately 260 MPa and 110 HV, respectively, after aging at 723 K for approximately 36 ks. Tamagawa et al. studied that the strength of Cu–Ni–P alloy rapidly increased at about 125 HV during the cooling process after the heat brazing due to the Ni2P precipitates sized 5–10 nm. Furthermore, Inagaki et al. achieved a Vickers hardness of approximately 130 HV by aging at 498 K for 10.8 ks. In the present study, we focused on the lowest aging temperature of 498 K in the previous study, and investigating the effect of heat-treatment simulated brazing on the mechanical properties of the Cu–0.93 mass%Ni–0.24 mass%P alloy.

Jan 1, 2019

By G. E. Parsons

"The Bidgood is a small gold mine about 5 miles east of the main Kirkland Lake camp. Since the beginning of production in 1934, gold having a value of $5,000,000 has been produced from the property. Practically all of this production has come from seven veins in a diorite stock that intrudes the Timiskaming sediments and lavas of the area. The veins consist of quartz, pyrite, and molybdenite with minor amounts of chalcopyrite, calcite, and tellurides, and occupy northeast striking and northwest dipping thrust fault fractures. They have no apparent direct structural association with the faults of the main Kirkland Lake camp or the Larder Lake 'break' to the south; however, the veins closely resemble the former in their mineralogical composition and in their close association with syenite intrusives.ROCK TYPES AND THEIR STRUCTURAL CHARACTERISTICSThe dominant and, from an economic standpoint, most important rocks in the ore area consist of two separate families of Algoman intrusivesa diorite and a later syenite group."

Jan 1, 1954

By George P. Demopoulos

In this paper the author will provide an overview of over 20 years of research & developments in the area of hydrometallurgical arsenic immobilization that culminated recently in the industrial implementation of the atmospheric scorodite process. The paper will consider various aspects of arsenic fixation in the non-ferrous metal industry from the iron-arsenic co-precipitation process employed to arsenic-bearing effluent solutions; to autoclave processing of arsenical copper and gold feedstocks and the fate of the in-situ formed iron sulphato-arsenate precipitate phases; the precipitation and stability of scorodite; the possible stabilizing role of mineral phases like yukonite, and the development of "scoroditeplus" processes employing novel encapsulation strategies. Emphasis is placed on the characterization and long-term stability of the various forms of arsenic-immobilized phases under either oxic or anoxic conditions over a wide pH range and the establishment of critical links between process parameters and hazardous material stability, contributing thus to advancement of new generation safe and sustainable waste management technologies.

Jan 1, 2014

By T. Maruyama

Tamano Refinery started its operation in 1972 with the cathode production capacity of 84,000 tons per year. After several expansions, the production capacity increased to 228,000 tons per year in 2001. In this paper, we are introducing our next expansion projects starting October 2006. The project expands the production capacity of cathode from 228,000 tons to 260,000 tons per year. The main modification of this project is the conversion to the ISA process and the installation of additional seventy-two cells in the No.2 Tankhouse. The No.1 Tankhouse remains the same, using the conventional process. Half of our starting sheet cells are converted to commercial cells. The other expansions are to enlarge our purification plant. And the incidental facilities are enlarged, for example, circulation tanks, heat exchangers, filtration system, etc. Finally, this paper describes those improvements to our refinery performance and preparing for future expansions.

Jan 1, 2007

By C. S. Chen, Y. J. Luo, M. W. Gao, B. Li, Z. F. Zhang

"To obtain large-sized billets with fine grains and homogeneous elements distribution, uniform direct chill (UDC) casting process, based on annular electromagnetic stirring coupling with intercooling, was employed to produce 7055 alloy billets with a size of F584 mm in this study. The results indicated that there were the coupled effects of annular electromagnetic stirring and intercooling on grain refinement and element homogenization, and also the billets produced by the UDC casting process showed excellent hot workability in comparison to the normal direct chill casting process.INTRODUCTION The high solute 7055 aluminium alloy has a wonderful combination of high specific strength and hardness, good resistance to stress corrosion cracking and high fracture toughness, which is very useful in aerospace application (Yan et al., 2013; Mondal & Mukhopadhyay, 2005). The production of large-sized 7055 alloy billets with high quality is the basic condition for the subsequent application of 7055 alloy to the aircraft. Inhomogeneous microstructures and performances of 7055 billets result from the high alloying element content and the inhomogeneous cooling condition in different regions of billets during the conventional direct chill casting (Paramatmuni et al., 2004; Lalpoor et al., 2011), which will bring bad influence to processing property, functional performance and utilization rate of materials. To alleviate segregation and obtain fine and uniform grains, some effective treatment methods were proposed including electromagnetic stirring (EMS) (Vives, 1989), ultrasonic vibrating (Zhang et al., 2011) and melt conditioning (Fan et al., 2013), on the melt to obtain fine and uniform grains. However, these methods could not effectively decrease the large temperature difference between central and periphery parts of the billet, because the solidification mainly depends on outside cooling including mould cooling and water spraying cooling. To change the heat extraction pattern of the billet functioned solely from the outer surface, based on annular electromagnetic stirring (A-EMS) invented by Xu et al. (2010), Luo et al. (2017) proposed uniform direct chill (UDC) casting coupling A-EMS with intercooling in the direct chill (DC) casting process. An in-mold cooler was inserted to the melt sump, and thus the alloy melt temperature and concentration at solidification front become more uniform."

Jan 1, 2018

By Barbara H. Scott Smith

"During the last two decades lamproites have joined kimberlites as the only two known primary sources of economic quantities of diamonds. This paper contrasts the petrography, primary and xenocrystic mineralogy and pipe geology of these petrogenetically separate rock types. The petrographic discrimination of kimberlites and lamproites from each other, as well as other rock types found during diamond prospecting, is discussed. Kimberlites and lamproites can be classified texturally and mineralogically. Such classifications highlight the differences between, and among, lamproites and kimberlites. The implications of these differences for diamond exploration programs are discussed, with particular emphasis on the application of petrography. IntroductionKimberlite was the term coined in the late 19th century to describe the host rock of diamond at the type locality, Kimberley, South Africa (Lewis, 1887, 1888). Innumerable kimberlites are now known worldwide; some of them contain economic quantities of diamond (e.g. South Africa, Botswana and Russia) while many are barren. Jennings (1989) suggests that less than 3% of the known kimberlites can be considered to be commercial. Kimberlite was thought to be the only important primary source of diamond for approximately a century. Until the late 1970s, lamproites were thought to be only academic curiosities. Some workers (e.g. Wade and Prider, 1940), however, did comment on certain similarities between lamproites and kimberlites and, hence, inferred a potential for lamproites to carry diamonds.The term lamproite was introduced by Niggli (1923) for leucite-bearing rocks from southeast Spain and Wyoming which had some unusual geochemical characteristics. Wade and Prider (1940) used the term lamproite (as defined by Troger, 1935) to embrace rock types found in the West Kimberley area of Western Australia. All the lamproites described by Wade and Prider (1940) form distinct topographic features. Subsequently in the late 1970s, additional pipes, which have little or no relief, were discovered in the same area, but only as the result of a major diamond exploration program (Atkinson et al., 1984; Jaques et al., 1984, 1986). Some of these bodies are diamondiferous. In 1979, the Argyle pipe was discovered in the East Kimberley area which, in terms of grade, is the richest known primary diamond deposit in the world with some parts of the body having grades greater than 500 carats/100 tonnes (Madigan, 1983; Boxer et al., 1989). All the initial new discoveries in Western Australia resulted from classic stream sampling for ""kimberlite indicator minerals"" (Atkinson, 1989)."

Jan 1, 1992

By M. Goto, F. Kubota

"In this study, we show the successful separation of rare earth metals, which are indispensable elements for the high-tech industry, from a solution containing a metal mixture by using a liquid-liquid extraction and liquid membrane based on ionic liquids. We employed newly synthesized N, Ndioctyldiglycol amic acid (DODGAA) as an extractant for rare earth metals. The DODGAA exhibited a high affinity for rare earth metals such as Y, Nd, Eu and Dy and the extraction efficiency was greatly enhanced in ionic liquids (ILs). Furthermore, stripping of the metals was readily achieved by using an acid solution. INTRODUCTIONRare-earth metals have important applications in cutting-edge technologies employed in the electronics, information technology, and automobile industries. As Japan does not have many natural metal resources, maintaining a steady supply of imported rare-earth metals is important. The total amount of rareearth metals imported into Japan was 19,000 tons/year in 1996, and this amount increased to 40,000 tons/year over the following decade (Kramer 2010). Japan is now one of the world’s major importers of rare-earth metals (Kramer 2010). However, more than 90% of the rare-earth metals imported into Japan come from China, the world’s leading supplier of rare-earth metal resources, due to their low costs. This situation made us realize the importance of a second resource of rare-earth metals: “urban mines” or discarded electronic waste. Rare-earth metals are generally separated from their natural ores by solvent extraction. However, since urban mines have different metals and the concentrations of rare-earth metals are usually low, highly efficient separation and recovery methods are required for rare-earth metals.Recently, ionic liquids (ILs), which are molten salts at room temperature, have attracted considerable attention since they are novel, environmentally friendly solvents (Kubota & Goto, 2006; Han & Armstrong, 2007). The use of ILs in liquid-liquid extraction of rare-earth metals has been reported (Kubota et al., 2012). In some cases, the IL-based systems showed better extraction ability and selectivity than those showed by the conventional organic solvent extraction systems(Nakashima et al., 2003, 2005; Hirayama et al., 2008; Fang et al., 2012). Therefore, more efficient solvent extraction processes by using ILs can be developed. In this study, we investigated solvent extraction processes in which ILs are employed and discuss the possibility of using ILs in the separation and recovery of rare-earth metals from electronic waste."

Jan 1, 2012

By D. K. Matlock, D. J. Hamre, J. G. Speer

Ultrafine ferrite (UFF) grains may be produced in surface layers of plate steels using controlled intermediate cooling followed by deformation. Experiments were conducted using a 0.12 C - 1.26 Mn steel on a Gleeble 1500 hot deformation simulator. Taguchi designed experiments were used to evaluate prior austenite grain size, intermediate cooling rate, intermediate cooling temperature, intermediate hold time and amount of reduction in order to observe the effects of variables and their interactions on the final microstructure while minimizing the number of required test runs. Evaluation of resulting microstructures and mechanical properties revealed a preferred thermal and mechanical history for developing ultrafine microstructures in surface layers of plate steels. Application of the fundamental concepts of phase transformations to industrial plate rolling is considered.

Jan 1, 2004

By J. Patterson

"Acid Mine Drainage (A.M.D.) formed from oxidation of disposed pyritic wastes presents a potential pollution hazard for Equity Silver Mines Limited and the mining industry in general. Failure to collect and treat these acidic effluents can eventually affect the quality of receiving streams and endanger aquatic life forms. Treatment and discharge of A.M.D. to the receiving environment must comply with stringent anti-pollution laws.Wastes mined at Equity Silver Mines Ltd. are predominantly acid generating and must be handled according to a materials management plan to minimize impact on the environment. Effluent collection and treatment facilities have been constructed to address the short term environmental concerns with reclamation and research programs being developed to address and monitor abatement measures for control over the long term.The purpose of this paper will be to offer a brief overview of these measures. Key topics for discussion will be: kinetics of Acid Mine Drainage, acid generating potential, water treatment and sludge handling, special wastes, waste dump construction, waste rock amendments, bacteriocide research, simulations, and reclamation measures. Programs designed to evaluate impact on the receiving environment, although they form an extensive part of the program, will not be discussed in this paper.INTRODUCTIONEquity Silver Mines Limited is located in the Central Interior of British Columbia, within the Omineca Division, 35 kilometers southeast of Houston Mining and approximately 575 kilometers by air north-northeast ofVancouver (Figure 1).The deposit consists of three economic mineralized zones: The Southern Tail, Main and Waterline Zones. Mining of the Southern Tail commenced in April, 1980 and was completed in the first quarter of 1984. Main Zone production was initiated during the last quarter of 1983 and the Waterline Zone remains undeveloped to-date. Remaining reserves are in the order of four years contingent on favourable metal prices. The three deposits (Figure 2) occur within a window of interbedded volcanic and minor sedimentary rocks. The older volcanic sequence is bounded on the west by a small granite-like stock and on the east by a gabbro-monzonite complex. All are overlain by a series of younger lava flows."

Jan 1, 1988

By Jörgen Appelgren

Atlas Copco, a leading supplier of equipment and services to the mining and construction industries, is consistently pursuing its strategy to offer the most productive and economical solutions by continuously offering new innovative products. These are in most cases developed and tested in close cooperation with demanding end users before being officially launched on the international market. The demands for higher productivity and improved overall economy have resulted in systems for automation of the drilling cycle and also tools for integrating the Drilling equipment to the production control system used by the customer. In terms of improving the blasted material quality, Atlas Copco has placed emphasis on hole straightness and the need for hole logging and positioning. By applying state of the art technology to today?s computerized drilling rigs, major steps in improving overall drilling and blasting performance have been achieved. This paper will give some examples derived from the latest development of solutions for the Rotary drilling product line.

Oct 1, 2009

By Brian McIntrye, Bo Trygg

"The need for grinding mills of ever increasing capacity and greater feed openings has tended toward mill trunnion diameters being beyond the size limits for roller bearings.Hydrodynamic plain bearings need to be wide enough to achieve the necessary bearing pressure in order to obtain an oil film with sufficient carrying capacity at low rotational speeds. This greater width increases edge loading resulting from the deflection of the mill under load.Because of the high surf ace pressure involved, the life of support rollers and girth rings is often inadequate-fatigue leads to flaking on the contact surfaces. Heat treatment of the girth rings also has its problems.The hydrostatic shoe bearing permits unlimited trunnion diameter and a high carrying capacity. The self-aligning shoes compensate automatically for radial deviations and large deformations can be tolerated at the girth ring.The sliding surfaces are completely separated by oil under pressure, enabling negligible starting torque and good damping capacity to be achieved together with low rotational speeds.IntroductionHydrostatic bearings have been known within machine technology since 1865, when the Frenchman Girard received a patent for such a bearing. During the following 75 years, these types of bearings were used sporadically for thrust bearings, primarily in water turbines. The first usable radial bearing was not designed until 1938. Since the 1950s, when hydrostatic bearings started to come into use within the field of machine tools, extensive research and development work has been carried out at various institutions and research centres throughout the world. Many support problems are now solved by means of hydrostatic plain bearings and the primary factor in deciding to use them is their unique characteristics:• ability to carry high loadings• no starting torque• large damping capacity• no wear• large running accuracyThe hydrostatic shoe bearing has been developed specially for use in the heavy machine industry, with the requirements for high loadings and large support diameters which this market demands."

Jan 1, 1982

By Alireza Sarafi, Alijan Aftabi

"A hydrocyclic system used for mineral separation at the laboratory scale results in the separation of more than 90% of micas. The system functions only by water and might offer advantages where other methods of mica separation are not available. INTRODUCTIONVarious methods for the separation of micas, wollastonite, and garnet, e.g., screening, flotation, magnetic separation, and heavy liquids, are well known (e.g., Spence, 1929; Bates,I960; Gillson et al., 1960; Benjamin, 1971; Connor and Kolhnar, 1991; Collings and Andrews, 1991). However, where these methods are not available, the separation of micas by a hydrocyclic system developed by Sarafi and Aftabi (1991) may prove to be economic. This note is a brief description of the hydrocyclic system. Minerals and MethodFor testing the recovery of mica and other minerals from different rocks (garnet-mica schist, skarn, and pegmatite), standard minerals were tested first, and then rock samples. Pure mineral standards were prepared from coarse-grained samples of pegmatite, mica schist and skarn; the grain size of the minerals separated was more than I cm. The Hydrocyclic System and Mineral SeparationThe hydrocyclic system is shown schematically in Figure 1. In the first step in mineral separation, mineral and rock samples were crushed, milled, and then sieved to minus 250 plus 125 microns. Approximately 10 gm to 25 gm of the sample were inserted in decanter Dt • The motor pwnps, M1 and M2, were then turned on and the water valve rl was opened. At this time, water was flowing turbulently (30 em3/sec. to 50 em3/sec.) and minerals were separated according to their crystallographic nature, density and!or habit. The fInal separation was done by exit valves r2, r3 and r4, while the motor pwnps were still operating. After each experiment, the rt , r2' r3 and r4 valves were closed and the motor pumps were turned off. Following this, minerals in each decanter and the mter were collected, dried and weighed. The whole time of the experiment was optimized to be about 10 minutes, but varied from 3 to 15 minutes for micas and garnets. respectively."

Jan 1, 1994

By D. S. Conochie

The world is poised for rapid growth in consumption as large, less developed economies acquire greater wealth. It might be expected that there would be a corresponding growth in waste generation, but this might not necessarily be the case. The metallurgical industry has an excellent record of process development which has allowed it to provide a high tonnage supply of low cost, high quality metals. Environmental challenges have been faced and indeed the recycling of scrap iron through the electric arc furnace has made a massive contribution to cleaning up obsolete structures and equipment of past generations. Issues in waste generation and processing still remain, and the expectation for cleaner processing and environmental performance continues to rise. The waste impact of key process developments of the last century and the recent developments in metallurgical waste processing in Canada will be outlined. The potential to use state of the art design tools to produce the next generation of zero waste processes will then be explored.

Jan 1, 2004

By John S. Stevenson

The Twin ''J' mine is on mount Sicker; 8 miles by road northwest from Duncan; on Vancouver island. It includes the old Lenora; Tyee; and Richard III mines; formerly under separate ownership but now under the single ownership of Twin "J' Mines; Limited.

Jan 1, 1954

By D. G. Macintyre

Thick westward prograding clastic wedges were deposited along the margin of ancestral North America from Mid-Proterozoic to Mid-Paleozoic time. Periodic rifting and tectonic subsidence resulted in the formation of starved sub-basins along this otherwise passive continental margin. These sub-basins host important sedimentary exhalative barite-zinc-lead-silver deposits. In northeastern British Columbia, a thick succession of Paleozoic basinal facies clastic rocks is preserved within the northwest-trending Kechika Trough. Within the trough, sedimentary exhalative barite and barite-sulfide deposits occur in starved basin sediments of Middle Ordovician, Early Silurian, and Late Devonian age. The last are the most economically sigrrificant and are hosted by carbonaceous cherty argillites and siliceous shales of the Middle to Late Devonian Gunsteel Formation of the Lower Earn Group. The largest deposit, Cirque, has reserves in excess of 35 million tonnes averaging 100J0 (Pb +Zn) and 47 g/t Ag. Other potentially significant deposits include Driftpile Creek, Bear, Mt. Alcock, Fluke, Pie and Elf. Stratiform barite deposits are also common, particularly near the basin-to-shelf transition zone. The Late Devonian barite-sulfide deposits typically are zoned: interlarninated barite-sphalerite-galena-pyrite occurring near suspected vent areas grades outward into bedded barite. Laminated beds of pyrite typically occur in hangingwall siliceous shales, particularly above the inferred vent zone. The apparent absence of epigenetic stringer sulfide zones and footwall alteration implies that the deposits were formed from ponded brines at relatively low temperature. Away from the main deposits, the favourable stratigraphic interval is marked by the presence of thin beds of nodular and laminated barite and thin laminae of pyrite. Thin tuff beds also occur locally in this stratigraphic interval and are evidence for a Late Devonian volcanic event. A paleogeographic reconstruction of the Kechika Trough in Late Devonian to Mississippian time suggests that the barite-sulfide deposits formed in third-order starved basins between uplifted, northwest-trending horst blocks that were capped by shallow-water carbonate banks. The presence of intraformational breccias suggests that fault movement accompanied barite-sulfide precipitation. This tectonic activity may have allowed the escape of heated, overpressured metalliferous brines from permeable reservoirs within the sedimentary pile. Sedimentary exhalative deposits formed where these brines were exhaled as buoyant plumes onto the seafloor, cooled, and ponded in anoxic seafloor depressions.

Jan 1, 1992

By M. Epiney, A. Ghahreman, R. Kim1and

"Pre-oxidation and cyanide leaching behavior of gold in the presence of sulfide minerals were reviewed, focused on the effects of oxygen injection in the gold leaching process. Generally, pre-oxidation and gold leaching kinetics from iron sulfide refractory minerals, such as pyrite, pyrrhotite, marcasite, pentlandite and arsenopyrite, can be enhanced with higher dissolved oxygen (DO) concentration. However, most of copper sulfide minerals dissolved well both in water and cyanide solutions, and copper from the minerals consumed DO and cyanide to oxidize and leach. Only in the presence of chalcopyrite, gold leaching was effectively occurred with increasing DO. However, chalcocite and covellite severely retarded gold leaching. Stibnite, an antimony mineral, formed a passive film on the gold surface under any DO conditions, and it slowed gold leaching. This impeding effect can be alleviated by leaching at low pH or adding lead salt. Using oxygen and lead together can make synergistic effect in oxidation of sulfide minerals and can enhance gold extraction. Depending on the mineralogical characteristics of the ore, the optimum DO and lead concentrations can be optimized. However, lead can cause environmental problems, and so its dosage should be minimized or eliminated by substituting it with oxygen injection.INTRODUCTIONGold ores containing sulfide minerals are becoming more significant as high grade gold oxide deposits are continuously becoming difficult to find. In light of this situation, to produce more gold, recovery methods from refractory gold ore containing various sulfide minerals should be investigated. Generally, sulfide minerals have impeding effects on gold leaching: formation of a passive film on the gold surface, high consumption of chemicalssuch as cyanide and oxygenduring leaching, reduction of gold cyanide by sulfide ions, etc. (Senanayake, 2008). Therefore, sulfides must be properly treated for better gold recovery. Pre-oxidation of sulfide minerals by injecting pure oxygen can decrease the impeding effects in gold leaching. Prior to cyanidation, sulfide minerals can be oxidized to metal hydroxide and sulfate form, which consume negligible cyanide in the following cyanidation circuit (Bodnaras et al., 1993). Moreover, gold cyanidation can be enhanced by increasing concentration of the dissolved oxygen (DO). In general, the optimum concentration ratio of [CN-]/[O2] is calculated as 6, but it goes higher in the real system (Marsden &House, 2006), which means that the reaction is typically controlled by DO concentration."

Jan 1, 2017

By Ken Wood, Luc Duval

"The development and operation of the milling circuits treating the different Selbaie orebodies are discussed in this paper. The project is reviewed from metallurgical evaluation through construction to present operating status. The current flowsheets are described, with discussion of some unusual features.IntroductionThe Selbaie concentrator commenced initial production in August 1981, treating underground B zone copper ore in a single 1500 t/d circuit. Throughput was increased to 1650 t/d in 1985. The mill was expanded in 1986 to treat ore from the A-I zone open pit; an independent circuit was added to selectively treat 5000 t/d of copper-zinc ore. Current total mill throughput through both circuits averages 7200 t/d with the production of approximately 270 t/d of copper concentrate and 230 t/d of zinc concentrate.This paper describes the stages involved in bringing the project from initial laboratory testing to its current status as one of the most important producers of silver, copper and zinc in Quebec and a major employer in the region."

Jan 1, 1990

By N. Katsikaros, A. Lewis-Gray, P. Richards

"To optimize gold recovery in complex leach-to-electrowinning processes, Gekko Systems developed the Gekko resin exchange column (G-REX) as an intermediate step, using a highly gold-selective resin to isolate contaminant metals. The AuRIX®100 resin produced by Purolite is licensed exclusively to Gekko, with the G-REX column designed specifically for this resin. Operational experience has been gained at the Castlemaine Goldfields Ballarat gold mine. In near-continuous operation since 2008, the Ballarat plant treats unclarified concentrate leach solution. The extension of this technology to higher throughputs and more complex chemistry is discussed.RÉSUMÉ Afin d’optimiser la récupération de l’or dans des procédés complexes impliquant la lixiviation suivie de l’extraction électrolytique, Gekko Systems a développé la colonne Gekko de résines échangeuses d’ions (G-REX) comme étape intermédiaire, à l’aide d’une résine hautement sélective pour la récupération de l’or qui permet d’isoler les métaux contaminants. Gekko détient la licence exclusive pour la résine AuRIX®100 produite par Purolite, et la colonne G-REX a été spécifiquement conçue pour cette résine. C’est à la mine d’or Ballarat de Castlemaine Goldfields que l’expérience opérationnelle a été acquise. L’usine de Ballarat, en exploitation quasi-continue depuis 2008, traite une solution concentrée non clarifiée de lixiviation. L’extension de cette technologie à des capacités supérieures et à une chimie plus complexe est examinée."

Jan 1, 2017

By C. G. Kemsley

THE ore as hoisted is very wet, and difficulty was experienced i~ screening it to remove the fines before going to the secondary crusher. In fact, the fines had a tendency to form balls and roll down the screen, and only a small percentage was removed. Their inclusion with the other ore going to the Symons secondary crusher caused excessive spring action and pounding between the adjustment ring and main frame, resulting in abnormal wear between the two. To overcome this, it was decided to wash the fines through the primary screen, and use an Akins classifier to de-water the screenings, pumping the overflow from the classifier up to the mill and discharging the oversize onto the mill-feed belt.

Jan 1, 1945