Search Documents

By Dave Bulled

"This paper describes the design of a molybdenite flotation circuit using FLEET technology applied to kinetics data produced from laboratory flotation testing and distributed across the blocks of a mine plan using a geostatistical approach. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the kinetics estimates of each block of ore in the mine plan. The final design then included a quantification of risk based on the accuracy of the block flotation kinetics and model fitting. The design made reference to the extensive technical reports describing earlier metallurgical test work including some pilot plant work over thirty years ago.The testing involved conducting MinnovEX Flotation Tests (MFT) to determine the rougher flotation kinetics at the specified reagent conditions and rougher-cleaner tests to determine the change in kinetics resulting from regrind. These flotation kinetics were used within FLEET simulations to create a full-scale flowsheet and plant design including recommended equipment sizes and the forecast of operating results. Measurement of detailed flotation kinetics for a wide range of samples allowed the effect of size of grind and efficiency of classification (i.e. width of size distribution) to be predicted for the whole ore body.INTRODUCTIONAdanac Moly Corp. proposed to develop a 20,000 ton per day mill to produce high quality molybdenite concentrate from its Ruby Creek resource in north-western British Columbia. It is a relatively clean low grade porphyry-monzonite occurrence containing minimal quantities of other sulphides such as chalcopyrite, pyrite, sphalerite and galena. Molybdenite occurs mainly as coarse flakes with lesser amounts of finer sized values. An optimum plant design was required to can achieve the predicted operating results, at a known level of risk, while treating the variability inherent in the ore body."

Jan 1, 2007

By M. C. Villeneuve

A numerical modelling approach was developed to explicitly simulate geomechanical characteristics of intact rock: mineralogy, grain size and fabric. The approach involved creating a representative constitutive model for each of three common rock-forming minerals: mica, quartz and feldspar. The constitutive models developed are valid within the low confinement realm of excavation boundaries, where tensile fracture processes dominate. The mineral types were assigned to numerical elements, which were associated with each other through an algorithm created in a finite difference model, FLAC 2D (Itasca 2007a), to simulate real crystal geometries and orientations. The numerical models were used in a parametric investigation of the geomechanical characteristics and compared with published observations of the rock yielding process in laboratory testing. This approach has allowed the explicit grain-scale investigation of the impact of geomechanical characteristics on rock yielding at low confinement, leading to an improved mechanistic understanding of excavation-scale rock yielding processes at excavation boundaries.

May 1, 2009

By Agbo Chima

Low-lying sections of open-pit mines accumulate water, especially during the rainy seasons, preventing access to resource-bearing areas. To sustain mining operations, the water must be lifted out of the flooded pits at a high flow rate using pumps. These pumps need to be mobile so that they can be removed during drill-and-blast operations. Most mobile pumps rely on diesel engines with high maintenance requirements. A special pump design was developed to address the unique needs of open-pit mining while making the dewatering process more sustainable. Using the target flow rate and head data, an efficient pump was designed, encased, and deployed in the open pit. A variable speed drive (VSD) was installed in a protective skid so that the pump could be tuned to match the preferred flow rate at any point during its operation. This system was tied to the national electrical grid instead of being powered by diesel pumps, which reduced the carbon intensity per kilowatt-hour. The high availability, low maintenance requirement, and greater reliability reduced the use of spare parts, the fuel consumption, and the logistics associated with operating the pump. This further reduced the carbon footprint of the dewatering process. This paper provides some of the two-year performance metrics for a deployment in West Africa. With a focus on availability, maintenance costs, average cost per volume lifted, and carbon footprint, this encased pump system is compared to the diesel-driven pumps that it aims to replace.

Jan 1, 2023

By F. Khomamizadeh

In this study, deep cryogenic treatment was applied to A319 cast aluminum samples. Although the cryogenic treatment didn't have any significant effect on mechanical properties of the well degassed and fluxed samples, but the tensile strength of the samples containing a considerable amount of gas and shrinkage defects was improved surprisingly, This improvement was attributed to the strengthening of the a-aluminum matrix which slows down the propagation of the existing defects. There was no significant increase in the hardness after cryogenic treatment, The abrasion resistance of the alloy was improved after cryogenic treatment, by developing a homogeneous protector shield, composed of abrasive grains penetrated into the soft aluminum matrix and kept tight.

Jan 1, 2005

By H. Mindivan

In the present study, the feasibility of recycling AA6061 Al alloy chips by a combination of ciyomilling, cold compaction and hot extrusion processes was investigated. Furthermore, the effect of Al powder addition to the recycled Al alloys chips on the mechanical properties was investigated. The characterization of recycled Al alloys was made by structural examination and mechanical tests (hardness, compression and dry sliding wear tests). The results indicated that by increasing wt. % of Al powder added to the recycled Al alloy chips the studied properties (the density, hardness, compressive strength and wear resistance) increased due to reduction of porosity in the recycled Al alloys.

Jan 1, 2011

By P. R. A. Andrews

"Talc ore from Bakertalc, High water, Quebec analyzing about 60% talc, previously dry ground to about 95% minus 53 µm was beneficiated in an 11.4 kg/ h pilot-plant flotation circuit. A concentrate of 95.9% talc (necessary for paper-grade) was obtained at a recovery at 75.3% by employing 53 g/t of Dowfroth 250 collector at pH 9.2; further cleaning increased the grade to 97.2% talc at a recovery of 57.5%.Flotation of fresh ground 60% minus 44 µm ore at a feed rate of 18.6 kg/ h produced a grade of 96.4% talc with a recovery of 78.2%, using Aerofroth 70 collector a six carbon-branch chain alcohol, at pH 9.2.The similarity in the concentrate grade and recovery between pre-ground and fresh-ground ore indicated that it was not neces¬sary to grind to 95% minus 53/2m to achieve comparable selectivity. A grind of 60% minus 44 pm corresponds to 100% minus 300 µm.Flotation retention times obtained with fresh ground ore indicate 33 min. for combined rougher/scavenger, and 15 min. each for the first and second cleaners.Talc-magnesite flotation separation is explained in terms of physico-chemical forces, with reference to surface charge and adsorption mechanisms."

Jan 1, 1989

By J. M. Beeckmans, S. G. Butcher, M. Goransson

"The counter-current fluidized cascade is a novel and potentially efficient pneumatic gravity separation device. Data are presented on over 150 runs of cleaning Alberta thermal coals, covering several size ranges. The coarser sizes of coal were processed in admixture with a fluidizing medium consisting of 0.5-by 0.1-mm hematite (or magnetite) and limestone particles. The partition curves for coal particles larger than about 3 mm, mixed with fluidizing medium, showed that the sharpness of separation achievable with the cascade approaches that of wet heavy medium processes, whereas with particles in the size range of 3 by 0.6 mm the sharpness of separation was comparable to that of a Baum jig. Useful cleaning was also achieved with particles smaller than 0.6 mm , Throughput rates of up to 11 tonnes per metre width of cascade per hour were achieved, with no indication of a deterioration in performance.IntroductionPneumatic coal beneficiation has steadily lost ground vis-a-vis hydraulic beneficiation during the past quarter century, primarily because of the sharper separations achievable with the latter methods. Nevertheless, there are certain inherent advantages of pneumatic separation methods which would give them an advantage in the market place were it possible to increase their efficiency to be technically competitive with those of hydraulic processes. These advantages are a dry product, resulting in a higher calorific value per ton, and avoidance of the problems associated with treatment and storage of process waste waters. Also, although it may be necessary to dry the raw coal prior to pneumatic processing, the dry rejects produced constitute an ideal fuel for a fluidized-bed combustor, which could provide heat both for drying the coal and for other purposes."

Jan 1, 1982

By Ting An Zhang, Chengzhi Jiang, Xiujing Zhai, Feng Xie

The extraction and concentration of nickel from aqueous solutions by emulsion liquid membranes (ELMs) using tributylphosphate (TBP) as extractant has been investigated in this research. The emulsion liquid membrane consists of a diluent (kerosene), a surfactant (Span 80), a mobile carrier (TBP), and a stripping solution (ammonia solutions). Important factors influencing the separation process including membrane composition, feed composition, and mixing speed have been examined. The results show that more than 90% of nickel in the feed solution could be extracted by ELMs under the experimental conditions, indicating the feasibility to use the designated ELMs to detoxify nickel-containing industrial waste solutions.

Jan 1, 2014

By M. Timmins

Campbell Mine operates a 100 tpd gold autoclave that treats sulphide concentrates at 305 psi and 200 °C. Autoclave feed consists of fresh pretreated concentrate, an acidic oxide slurry recycle as well as other high arsenic sources. The brickwork that is used to construct the five compartments of the vessel must be inspected and repaired periodically. Shutdowns are scheduled to inspect this brickwork and at times replace entire sections of the brick walls or lining. It also provides an opportunity to repair or replace other internal features such as agitator blades or oxygen spargers. Mechanics and contractors are scheduled around the clock to perform the maintenance requirements. There are many safety considerations and precautions that must be taken in order to protect the well-being of the workers and minimize damage to sensitive pieces of equipment. Heat, arsenic and lead contamination and confined space issues are just a few of the hazards involved. The following paper will describe how these safety concerns are addressed and will serve as a guide for future autoclave shutdowns.

Jan 1, 2004

By J. W. Hendry

"This paper will discuss the application of tools and the evolution of computer-assisted procedures in the production planning process at Quintett e Coal Limited (QCL). In 1986, QCL produced 5.3 Mt of clean coal from their surface mining operation located in north eastern British Columbia. The structural complexity of the sedimentary deposit and high rate of mining necessitate the consideration of large amounts of geological information which continually updates the interpretation. There are multiple unit operations required during the process of mining through a given multi-seam sequence, which results in many interdependent faces, and multiple iterations of scheduling sequences in order to satisfy a given set of objectives. In order to facilitate these activities in a timely fashion, it was recognized that a computer systems' capability needed to be developed which could increase the efficiency of information input, manipulation and output. IntroductionQuintette Coal Limited (QCL) has been operating a large metallurgical open pit coal mine in northeastern British Columbia, since 1982. The mine produced 5.3 Mt of clean coal in 1986 for export to Japan. Throughout the start-up period and the subsequent build -up of production levels, it became evident that the primary producing area was comprised of extremely complex faulted structures. This has resulted in development and modification of specialized mining methods employed to effectively recover the resource. Similarly, the planning and engineering techniques employed have been evolved over the same period of time. The implementation of computerized methods has been one of the major developments in this process, including geology interpretation, modelling, reserve definition, quantification, production planning and scheduling, and graphical plan presentation. These capabilities have been employed, in various forms, for project scale feasibility work and long range planning for some time, however, the use of computer tools for short-term, detailed production planning of a complex mining environment presents a different set of problems. It is hoped that a presentation of the current state of evolution and future plan s for development will be of interest to organizations considering implementation of a similar system."

Jan 1, 1988

By Z. I. Zaki

Synthesis of TiC /A1203 Composite from TiO2, Al and graphite using combustion technique has been investigated at different initial temperatures; room, 400 and 600 °C. The effect of initial temperature on the composition of the product, wave velocity and combustion temperature of the reaction was studied. The measured combustion temperature and wave velocity were increased with increasing the initial temperature of the combustion reaction. The maximum wave velocity obtained was 5.9mms-1 when conducting the combustion reaction at initial temperature of 600 °C. Oxidation resistance of the obtained composite was also studied at the temperature range 300-800 °C. No oxidation is detected before 400 °C while it takes place effectively at 700 °C forming different titanium oxides. Wave velocity measurements method was used to calculate the activation energy of the reaction between the starting materials. It was found to be 316.34 kJ mol 1 at the temperature range that was studied.

Jan 1, 2007

By P. Zhang, K. Liu, L. Ou

"The strength and mechanism of Portland cement prepared from stone coal vanadium slag were studied in this paper. Initially, the slag was used as silicon raw materials to prepare clinker. By blending the prepared clinker with gypsum, waste, and fly ash, a series of different grades cement got well prepared. All of performances of the cement were up to the requirements of China’s national standard. The hydration products and microstructure of cement were identified and analyzed by X-ray diffraction and scanning electron microscopy. With the comparison of cement hydration characteristics at different ages, the strength formation mechanism of cement was clarified. The experimental results suggested that adding the fine materials (mainly waste and fly ash) to replace part of clinker would accelerate cement hydration, as it provided additional surfaces for the nucleation and growth of hydration products. And the hydration products were similar to ordinary Portland cement, mainly containing the amorphous calcium silicate hydrates (C-S-H), acicular ettringite (AFt) and portlandite (CH). With hydration time increasing, the hydration products continuously covered the cement particles, resulting in a thicker surface layer. As a result, it gradually condensed into a dense structure block with small pores and smooth surfaces, which led to higher strength. In conclusion, using the vanadium slag to prepare Portland cement can realize the utilization of solid mineral wastes, which will bring huge ecological and economic benefits.INTRODUCTIONWith the development of China’s mining industry, more and more mineral waste residue is discharged every year. These solid wastes cause varieties of resources and environmental problems on people’s living area. While at the same time, the demands of cement are increasing with the remarkable development of the construction industry. Thus, in recent years, utilization of proper solid waste to prepare cement has become an efficient way to deal with the solid mineral wastes problems (Boncukcuoglu, Kocakeri?M, & Tosunoglu, 2002; Simatupang, Hanafi, Purwasasmita, Imran, & Pane, 2012; Tsakiridis, Papadimitriou, Tsivilis, & Koroneos, 2008; Yun, Yong, Choi, Lee, & Lachemi, 2009)."

Jan 1, 2016

By S. Lun Sin

In this study, the effect of silicon on the microstructure, mechanical properties and hot tearing susceptibility of permanent mould cast AZ91E magnesium alloy was investigated. Varying amounts of silicon (0.5, 1.0 and 1.5 wt.%) were added to AZ91E in the form of an Al-53 wt.% Si master alloy. The phase formation, grain size and solidification behavior of each alloy were characterized and related to their tensile properties and hot tearing susceptibility. The results showed that the addition of silicon resulted in the formation of Mg2Si particles. The presence of these particles led to an increase of the hardness, but was detrimental to the tensile strength and elongation of AZ91E. However, silicon significantly reduced the hot tearing susceptibility of AZ91E. This was attributed to the reduction of the grain size and the decreased freezing range of AZ91E, which contributed to improve the interdendritic feeding during the last stage of solidification.

Jan 1, 2011

By A. J. Petrina

"At Craigmont Mines Limited, Merritt, B.C., tests were begun in March, 1965 to evaluate the use of shotcrete as a method of ground support m development headings; previously, ail drifts had. required support, which was accomplished mainly by timber and occasionally by the use of rockbolts. The tests demonstrated conclusively the effectiveness of shotcrete for supporting Craigmont's ground. Gradually, the use of timber for ground support was virtually eliminated in favour of shotcrete. This paper describes the equipment used, the operation of the equipment, pertinent cast data and opera ting details. Also discussed are other uses developed for the shot-creting equipment, the use of reinforcing bar rockbolts, and a method used at Craigmont for lining long vertical ore passes with steel plate and concrete as part of the raising cycle."

Jan 1, 1968

By S. Usui, Y. Shinohara, C. Tokoro, K. Horiuchi, S. Owada

Process optimization of heating and physical separation for Cobalt (Co) recycling from spent lithium ion battery (LIB) was investigated. LiCoO2 in spent LIB was transformed to LixCoO2 which was more easily decomposed than LiCoO2 by heating. Coexisting materials of aluminum and carbon, and sealed atmosphere of the LIB promoted LixCoO2 decomposition. In an atmosphere of Argon, 95 % of LixCoO2 in the spent LIB was decomposed to 76 % of Co oxide and 19 % of Co metal in 10 min at 823 K; a lower temperature than the theoretical value for LiCoO2. The Co oxide and Co metal exhibited magnetic properties and could be recovered by wet magnetic separation. Furthermore, slow heating was effective for grain growth of Co oxide and Co metal. At 2 K/min rate of heating, average grain size of Co oxide and Co metal were 239 µm and 28 µm respectively, whereas at 30 K/min they were 190 µm and 15 µm respectively. Therefore, separation efficiency for Co recovery by wet magnetic separation was increased when spent LIB was slowly heated at 2 K/min.

Jan 1, 2015

By Takashi Nakamura, Atsushi Iizuka, Yong Fan, Etsuro Shibata

The level of iron in typical copper slag reaches nearly 40% by mass, in the form of iron silicate. We designed a method to oxidize the nonmagnetic iron silicate to magnetite, permitting the selective recovery of the slag’s iron content by magnetic separation. This would effectively decrease the volume of dumped slag; the reclaimed iron could be used for iron and steel making. The crystallization behaviors of magnetite and hematite were studied as reaction products of the molten oxidation of copper slag. A gas atmosphere of 1% by volume of oxygen was found to effectively precipitate the slag’s iron content as magnetite.

Jan 1, 2015

By O. E. Andrew

THE object of this paper is to present a brief summary of the dust control system in use on the 3,825-foot level at the jaw crusher station, Lake Shore mine. During the years 1936 and 1937, dust survey reports were presented to the management showing that high dust concentrations were being created during operating periods. At that time, however, this crusher was running only an hour or so each shift, and it was felt that no large capital expenditure for dust control equipment could be justified. In order to afford some protection to the operators, a number of respirators then on the market were .tested and the 'Comfo' respirator was adopted for use by the crusher-men. In 1938 this crusher began to handle a large share of the total mine tonnage and the hours of operation were increased. Further dust sampling showed increased dustiness with the longer operating time. It was also realized that the operators suffered considerable inconvenience if they wore their respirators throughout the shift. If the respirators were not worn, then dangerous amounts of dust were being inhaled. The fact that the crusher station was situated on the 3,825-foot level limited the means that could be employed to eliminate the dust hazard. At that rime there was not available the 5,000 c.f.m. of fresh air which would be required to sweep out or dilute0 the dust, and there was also no way of disposing of the contaminated air without passing it on for other men to breathe. Thus it became apparent that a self-contained dust disposal system would have to be installed.

Jan 1, 1941

By D. Markwart, B. Volk

Anode effects are a phenomenon of the aluminium electrolysis process which produce potent greenhouse gases called PFCs (CF4, C2F6). With concerns surrounding global warming, and increasing regulation of GHG emissions, anode effects have become a significant sustainability issue for aluminium producers. In modem smelters, sophisticated computer control and automated alumina feeding systems allow for very tight control of the alumina concentration in the electrolyte and thus very low anode effect frequencies. Older smelters, however, do not have these systems and must either invest heavily to obtain them, or find other, innovative ways to reduce anode effect frequency. This paper will present the integrated approach to anode effect reduction used in the Vertical Stud Soderberg (VSS) potlines at Kitimat Works. Through an innovative combination of simplified signal analysis, modified alumina feed control logic, anode effect prediction, and anode effect prevention using a pager based communication system, Kitimat W arks has been able to make significant reductions to its anode effect frequency.

Jan 1, 2006

By J. B. Sabey, V. R. Degner, D. MacGillivray

"Hydrodynamics principals are applied to the design of a natural air ingestion flotation machine for coarse solids applications. Preliminary laboratory test data and subsequent operating plant flotation kinetic performance evaluations are reviewed. INTRODUCTIONThe concentration of potash (sylvite, KCI) from halite and other salts using flotation is well understood and practice a with much success. Reagent schemes and plant circuitry for obtaining the desired product recovery and grade have been established with proven performance. These flotation circuits normally process the medium and finer size particles, less than 30 mesh (600 microns).However, often the potash market trends specifically demand a coarse product size. This emphasis, accompanied by the existing high losses of coarse (+30 mesh) potash in flotation circuits, creates the need for development of a flotation machines specifically designed for coarse potash beneficiation.This technical challenge was undertaken by the WEMCO Research and Development Group. The specific objectives of this flotation machine development program were ( l) to achieve an ""Ultra Coarse Flotation Machine"" capable of adequately suspending and transporting particles in the 4 - 30 mesh (4.75 - 0.6 mm) size range at solids concentrations of 30% or greater and (2) ascertain metallurgical performance of this machine.This paper covers the development (both theoretical and mechanical/ hydrodynamic), the field test program and results, a discussion of applicable flotation kinetics, and conclusions of this ""Coarse Potash Flotation Machine"" development project."

Jan 1, 1986

By Brent Robertson

Failure to meet quality objectives during the execution of any industrial project has lasting negative impacts on facility life cycle performance. Cost overruns, schedule delays, and rework are characteristics of project quality issues that arise during the project. Commissioning and start-up problems, low production, production bottlenecks, breakdowns and the necessity for operational work-arounds are characteristics of project quality issues that appear after project completion. Risks such as production facility downtime, shortened equipment life, and potential HSE violations must be clearly identified and addressed during project planning phases. Appropriate Quality Assurance (QA) and Quality Control (QC) focus must be placed on identified high-risk areas. In order to be effective, quality systems must be flexible, non-confrontational, consistent, and adaptable to projects of any size ? from capital mega-projects to small maintenance projects. All project participants must be aligned in how they are approaching quality and the difference between QA and QC must be clear to everyone on the project. Emphasis must be placed on QA activities to minimize project cost, reduce rework, manage change, and reduce the production facility operational risk. QA is focused on the work processes used to generate the design and confirming that the processes are present and being followed. Issues in the work processes guarantee that the output drawings and specifications will be less than optimal. The identification and monitoring of quality-critical processes provides a focus for QA activities. QC activities are then used to generate proof that the project was implemented correctly and become a key part of the turnover.

Nov 1, 2011