Search Documents

By L. J. Surges, C. Bazin, D. Hodouin

"A kinetic model was developed for the conditioning and flotation processes of an industrial lead concentrate dezincing circuit. The models were incorporated into a flowsheet simulator. Simulation results demonstrate the advantages of split conditioning of coarse and fine particles and the potential of this approach for the production of the heuristics required for the development of intelligent control strategies.The conditioning model relates the proportions of activated and hydrophobic surfaces and residual reagent concentrations to activator and collector reagent flowrates. The model accounts for the solids and water flowrates, and for the solids grade and size distribution. The flotation model uses the predicted proportion of hydrophobic mineral surface, the aeration rate and the froth depth to estimate cell, bank and circuit performances. IntroductionFlotation has been the object of modelling and simulation studies for more than two decades. The process is usually modelled as a kinetic one in which the particle flotation rate constants are key parameters. Rate constants are related to the operating variables (pH, reagent flowrates, aeration rate, etc), however these relationships are seldom established in the literature.In spite of the large amount of literature on flotation modelling and simulation, few papers deal with the interaction between flotation rate constants and operating variables. This important gap, which was identified in the early seventies by Woodburn (l970), still exists. One of the first attempts to include operating conditions in a flotation simulator was made by King (l973), who explicitly introduced the aeration rate into an air bubble loading model. Lynch et al. (1981) used an empirical model to relate the proportion of slow floating particles to the ratio of collector per ton of ore. Such empirical relationships are difficult to calibrate and cumbersome to use when an activator and a collector are added to slurries in which particle size distribution and surface characteristics are changing. Eascur and Herbst (l982) relate in a fundamental way the mineral flotation rate constants to the aeration rate, froth depth, agitation and frother concentration, however the model does not account for reagent flowrates. Niemi et al. (1982) have proposed a model for the conditioning of minerals and included it into a conventional flotation simulator."

Jan 1, 1988

By D. Yamada, T. Tanaka, N. Inouchi, J. Nakahigashi, H. Yoshimura, T. Nonishi

The use of cereal food materials as lubricants was investigated in an attempt to develop nonpolluting lubricants. Suspensions of wheat flour in water and other types of cereal food lubricants were prepared and their friction coefficients measured. The results indicate that a cereal food lubricant containing 30% lipids, 2% proteins, 60% carbohydrates and 0.6% calcium carbonates has the lowest friction coefficient for a sheet (cpTi-1). As example applications, the lubricant was tested with a forming press and a screw-fastening device. In both applications the cereal food lubricant performed relatively well in comparison to conventional lubricants and thereby has potential for practical applications.

Jan 1, 2006

By C. Karpuz, Y. S. Istanbulluoglu

This paper describes the results of convergence measurements conducted about five years for the re-use gate roadways at OAL lignite mine in Turkey. Double lignite seams separated with a marn layer, are mined with long-wall retreating mining system at the mine. Rib pillar has been abandoned and gate roadways were planned to be packed for the re-use of full extraction. Various packing systems have been attempted, namely three rows of woodenchock, one row of wooden chock plus concrete wall and concrete wall only. The re-use of maingate roadways packed with wooden chock yielded 62% of closure. Lastly developed concrete packing of 3 meters wide and specially developed support set composed of three friction props and a cap, which is a modification of yieldable set, have successfully maintained the main and tail gate roadways stability with a total vertical convergence of 32%. Good correlation has been established between pack stiffness and floor heave as well as maingate and tailgate convergences. The elimination of rib pillars by re-use of gate roadways increased the coal recovery by 20% and decreased the development/production ratio from 0.065 m3/ton to0.022 m3/ton.

Jan 1, 1997

By A. Bois-Brochu, G. Morin, G. Marin, M. C. Parr, J. Carignan

The presence of an alpha case on titanium parts produced by investment casting is problematic and has to be eliminated. The traditional techniques for the evaluation of its thickness are metallographic measurements and micro-hardness profiles. To obtain a better understanding of how the alpha case is formed with the underlying objective of limiting its depth, the present study proposes to characterize the microstructure and the chemical composition of the alpha case. Electron microprobe analyzer (EMPA) linescans were used to quantify the oxygen and substitutional elements that come from the mould and promote the alpha case formation. The chemical profiles were correlated with metallographic and microhardness measurements. For microstructure, optical microscopy (etched and polarized light analysis) was used. For phase analysis, samples were mechanically polished step by step and analysed using X-ray diffraction and optical microscopy. Furthermore, surface analysis techniques such as XPS and Auger Microscopy were evaluated but results were found to be inconclusive because the formation of the oxide layer was faster than its ablation and the matrix could thus not be analysed. The alpha case was observed on a Ti-6Al-4V step block casting.

Jan 1, 2014

"In conjunction with Banick Mercur , Wright Engineers Limited designed the first multi-stage aqueous pressure oxidation system in an alkaline environment in North America. A three-stage slurry heating and slurry pressure let-down with heat recovery was an innovative approach to the problem of high energy cost with the low sulphur content of the ore. The design of this system required solving a number of problems associated with heating and pumping of slurries at pressures up to 3230 kPa and temperatures in excess of 220°C. Wright received an Award of Merit in October 1989, from the Canadian Consulting Engineering Awards Committee in the Process Category for its design of the Mercur pressure oxidation system.The Mercur Mine is located at the south end of the Oquirrh Mountains in Tooele County about 65 miles by road from Salt Lake City, Utah, U.S.A. The original mill was designed to process 5000 tpd of oxidized gold ore in a carbon-in-leach (CIL) circuit. A new ore treatment system was required to treat the substantial quantities of refractory ore reserves which could not be treated economically in the existing mill. The new pressure oxidation circuit makes the refractory ore amenable to gold recovery by oxidation of the sulphides contained in the ore .Wright Engineers Limited was commissioned by Barrick Mercur Gold Mine Ltd ., a wholly-owned subsidiary of American Barrick Resources, to design the pressure oxidation facility. This followed completion of a feasibility study by Wright which showed that the project was technically and economically viable.Work on the feasibility study began in 1986, detail design commenced in February 1987, and was completed in December 1987. Mechanical installation was completed in January 1988, and slurry feed began in February 1988. The plant has operated since June 1988 without major interruption . Wright was responsible for engineering, procurement and construction management for the addition of the 750 tpd pressure oxidation circuit to the existing mill and also had commissioning responsibility.Major unit processes involved in the pressure oxidation facility are ore thickening, three-stage slurry preheating, pressure oxidation and three-stage slurry cooling with heat recovery, stearn generation, propane and oxygen storage and a video graphic display process control system were included in the scope as process anciliaries.The pressure oxidation increases gold recovery from the refractory ore by conventional CIL from as low as 35% to more than 86070. A patent has been granted for the process."

Jan 1, 1989

By Steve Wilkinson

"""Techniques for coarse-particle beneficiation of some gold ores and methods for determining potential for sorting any gold ore deposit.""With the advent of high speed computers, laser technology end different types of electronic sensing devices, ore sorting machinery has been developed, capable of handling significant tonnage rates while maintaining high level efficiency. Gold ores may be amenable to coarse-particle beneficiation where there exist measurable criteria upon which there can be recognition of auriferous versus barren lumps in the run of mine. Three types of criteria are suitable for sorting and are:i) Photometric - optical variance between ore and waste such as vein ores hosted by barren country rock;ii) Conductivity/Magnetic - based upon the metallic mineral content of ore end waste, and its association with Au, such as found in sulphide/arsenide Au ores,iii) Radtometric - detection of natural gamma activity occurring with uranium-bearirig gold ores.The method for determining the sortability of an ore depositconsists of, at least, three stages:i) Initial stage identification of ore and waste types,mineralogical/petrographical associations,amount of dilution in P.O.M.establishment of any sorting criteria]"

Jan 1, 1985

By Arthur D. FitzGerald

EDC established an Environmental Review Framework in 1999. Throughout the early fall of 2001, the Corporation held public consultations across Canada to strengthen that framework, leading to a public release on November 15, 2001 of a report summarising the results of these consultations. Following this, the Corporation implemented strengthened environmental review requirements in the form of its Environmental Review Directive, in compliance with legislated amendments to Canada?s Export Development Act that went into effect on December 21, 2001. Over the past few years, there has been a global trend towards an increase in the social and environmental requirements of multilateral/bilateral financial institutions and export credit agencies. More recently, this activity has focussed on capturing institutions that have not yet adopted similar requirements and, more specifically, on developing a convergence of the requirements from institution to institution. This paper describes EDC?s new ERD and some of the initiatives that have taken place or are in process that are moving international financial institutions toward converging their environmental and social requirements for projects in the private sector.

May 1, 2002

By James L. Parks, David M. Kjos

"Designs, installation procedures and performance characteristics of martensitic cast steel concaves are reviewed. Longer wear life, fewer pieces to install and eliminating the need to scarf joints are the principal benefits of using martensitic steel to replace austenitic12% Mn (Hadfield's) steel, the traditional concave material for large gyratory crushers. Installation procedures that reduce the risk of breakage are described. Operating practices that affect concave performance are also discussed.IntroductionThe crushing machine considered to be the forerunner of the modem gyratory crusher was patented in 1878 by Charles M. Brown of the Gates Iron Works(1). The earliest gyratory crushers with receiving openings of 6 to 12 inches were fed by hand, and the crushing capacity of a mine was increased simply by installing more small crushers. The introduction of the steam shovel to open pit mining around the tum of the century provided an incentive for much larger primary crushers, and gyratory crushers with a 48 in. receiving opening were being built by 1910, followed not long afterward by machines with 54 in. and 60 in. openings to . Fortunately for the crusher maintenance people of that era, an austenitic 12% Mn steel with exceptional toughness was already available, having been discovered by Robert Abbot Hadfieldoi in 1882. Although small gyratory crushers working soft- to medium-hard rock reportedly used chilled cast iron (white iron) wear parts, these newer and much larger machines were fitted with ""Hadfield's manganese steel"" concaves and mantles to withstand the impact associated with handling large rocks .M E International first challenged the long-standing convention of using 12% Mn steel concaves in large gyratory crushers in the late 1960s when they supplied upper row concaves in martensitic cast steel for a 60-109 primary crusher at a taconite plant on the Iron Range. Since then, martensitic steels have been successfully substituted for 12010 Mn steel in concaves for more than seventy primary gyratory crushers processing iron, copper and precious metals ores, industrial minerals and crushed stone.This paper reviews materials, designs and performance characteristics of martensitic steel concaves in large gyratory crushers. The principal benefits include significantly longer wear life, fewer pieces to install and the elimination of scarfing. Obtaining the full measure of these benefits and minimizing the risk of breakage is strongly dependent on installation procedures, which are described in some detail. Operating practices that can affect performance are also discussed."

Jan 1, 1993

By M. Mirnezami, J. A. Finch

The McGill component of the consortium contributed detailed examination of the electrokinetic properties of the constituent minerals, primarily pentlandite and serpentine. Mineral specimens were derived from an ore sample; mineralogical examination showed the serpentine was predominantly clinochrysotile, a fibrous mineral responsible for much of the flotation separation problem. The study included design of a novel sedimentation potential measuring device to classify the surface charge of the ore and electrophoresis measurements on single and mixed minerals which progressively approached flotation conditions. The sedimentation potential measurements provided a general association between surface charge and the visual state of aggregation as a function of pH. The electrophoresis experiments started with single minerals in a background of indifferent electrolyte and progressed to mixed minerals in a background of supernatant derived from an ore sample. The single mineral tests supported the suspected electrostatic interaction, i.e., hetero-coagulation, at flotation pH 9-10. The mixed mineral tests demonstrated this interaction and also revealed hetero-coagulation with Mg(OH)2 precipitates, derived from the supernatant. This interpretation was confirmed by optical and electron beam imaging. A series of agents, CMC, polyphosphate, soda ash, EDTA, were examined to disperse the system. To accommodate the small mass of single mineral available a novel turbidity measurement using a UV/Vis spectrophotometer was introduced. Selected conditions were used in contact angle and small-scale flotation tests.

Jan 1, 2011

By R. A. Sudisman, T. Yamabe, M. Osada

"Geological material can be subjected to some different loading conditions, mainly due to three inter-related physical processes which are mechanical, thermal, and hydrological. Freezing and thawing process of rock that occurs in sub-zero temperature condition may contain some or all those three physical processes depended on its initial condition. Those inter-related physical processes may lead the ground into failures. Therefore, understanding the physical properties such as deformation process of geological material under freezing and thawing condition is required for the artificial ground freezing projects and engineering construction activity in the natural cold region.In order to study the strain characteristic of rocks during freezing and thawing process, a series of freezing and thawing experiments of core samples of three different rock types and mortar has been conducted under varying temperature from -20 °C to +20 °C. Four core sample types are Sandstone, Granite, Tuff, and Mortar with 50 mm diameter and 50 mm height, which were naturally dried before the freezing-thawing experiment. Freezing-thawing experiment was conducted by submerging the vinyl covered core samples into a temperature-controlled liquid coolant box. Firstly, temperature of liquid (brine solution) was set at -20 °C so that the temperature of subjected sample was decreasing to as low as -20 °C. And then the temperature of brine was returning to initial room temperature after the coolant system was stopped. Strain gauge and thermo couple were attached on the core’s perimeter to measure strains and temperature changes.Sandstone and Mortar samples show relatively similar results than other two samples. Both presents linearly shrink with the temperature decrease and expand almost to its initial condition with the temperature increase. Granite shows less-linear strain-temperature relationship during thawing process, while the Tuff sample shows abrupt strain increase during thawing process on the temperature higher than +10 °C. Thermal expansion value of each rock types were obtained by fitting the major strain-temperature relationship on -19 °C to +10 °C temperature range. Overall, anisotropic deformation was observed on the entire samples and possible mechanisms for each hysteresis characteristic are discussed, which need to be confirmed by further experiments."

Jan 1, 2015

Introduction ?MT involves the measurement of naturally occurring magnetic and electric field oscillations. ?The ratio of E/H (wave impedance) is measured as a function of frequency to give resistivitydepth information. ?The ratio of vertical and horizontal magnetic fields (tipper) gives information about the location of (channeled) current systems.

May 1, 2008

By Jean-François Doyon

Les aspects environnementaux des activités minières d?exploitation réalisées sur le territoire québécois sont encadrés par divers cadres légaux, réglementaires ou autres (directive, politique, guide) tant au niveau provincial que fédéral. Ces cadres s?appliquent à l?un ou l?autre des trois grandes étapes du projet, soit lors de l?étude d?avant projet, pendant l?exploitation ou à la cessation des activités d?exploitation. Comme la réglementation environnementale est de plus en plus nombreuse, ces dernières années, cette présentation vise à exposer les principaux cadres provinciaux et fédéraux actuellement en application au Québec pour le secteur minier et à en dégager les particularités. ABSTRACT The environmental aspects of mining activities carried out across Quebec fall within the scope of various legal, prescribed or other frameworks (directives, policies, guides) at provincial and federal levels. These frameworks apply to one or another of the three major steps of a project: preliminary design, mining and closure. As the number of environmental regulations has greatly increased during the past few years, the object of this presentation is to state the main provincial and federal frameworks currently applicable in Quebec for the mining sector and to identify their special features.

Nov 1, 2002

By J. E. Nelson

This paper will examine the problems inherent in matching grinding mills with electric motors through connecting elements such as clutches. Emphasis will be on the uncertainties of mill torque and power demands and the need to recognize these if dependable, safe designs are to be obtained.

Jan 1, 1972

By Ben Burger

This paper describes the design, the first three years of operation and optimization of a large, single stage SAG mill at Minera Yanacocha?s Gold Mill facility located in northern Peru. The Gold Mill was commissioned in March 2008 with a 32? x 32? EGL, 16.5MW single stage SAG mill, to process 5 million tonnes per annum high grade oxide Au/Ag ore. Operational control, feed size distribution, grinding media, mill liner, grate and pulp lifter optimisation have allowed the mill to operate 15-30% above design throughput rates, but with a product P80 coarser than design. As part of the optimization, full grinding circuit surveys were conducted. Historical operating data and survey data were analyzed and used to evaluate possible circuit changes and determine alternative operating strategies. A number of changes were implemented which allowed the SAG mill to operate similarly to a large ball mill and achieve finer mill product that was closer to design. This paper summarizes life to date data analysis and improvements made by Minera Yanacocha as well as the grinding circuit optimisation study conducted by Metso Process Technology and Innovation.

Jan 1, 2012

By Zhan Zhang, Hiromi Nagaumi, Zhen Li

"Recently, the remarkable strengthening effect of ??-Al(Mn, Fe) Si dispersoids at both ambient temperature and elevated temperature were found by several researches. A large amount of dispersoids can be formed by applying special heat treatments and within a suitable range of chemical composition of AA3xxx alloys. In the present work, the influences of Cr addition on the mechanical properties and microstructures of the Al-Mn-Mg-Si alloys were investigated. The mechanical properties at ambient and elevated temperatures were evaluated by micro-hardness and yield strength. Moreover, the microstructures in as-cast and heat-treated conditions were quantitatively analyzed by optical and electron microscopes. Results revealed that Cr also had effect on the number density and volume fraction of dispersoids. Micro-hardness and yield strength at ambient temperature increased with the increasing content of Cr, and the Cr addition increased the yield strength at elevated temperature as well. Moreover, the creep resistance at 300°C improved dramatically with the increasing content of Cr.INTRODUCTION Traditionally, AA3xxx aluminum alloys were widely used in packaging, automobile and architecture industries, because of its good formability, excellent corrosion resistance and weldability. And AA3xxx alloys were considered as non-heat-treatable alloys. However, the strengthening effect of dispersoids in AA3xxx alloys was discovered recently (Li & Arnberg, 2003;Li, Muggerud, Olsen, & Furu, 2012; Li, Zhang, & Chen, 2016; Liu & Chen, 2015).Alarge amount of dispersoids could precipitate by a proper heat treatment.In order to further improve AA3xxxalloys, the composition of the alloys should be optimized. A few previous studies were reported to investigate the influence of compositions on AA3xxx alloys. Adding Mn element could enhance the precipitation of ??-Al(Mn, Fe)Si dispersoids and improve the yield strength(Muggerud, Mørtsell, Li, & Holmestad, 2013), as long as the concentration of Mn was under the solid solution limit. Fe decreased the solubility of Mn and accelerated the precipitation rate of ??-Al(Mn, Fe)Sidispersoids(Li & Arnberg, 2003), the yield strength and creep resistance at elevated temperature could increase with an optimized content of Fe(Liu & Chen, 2016). Mg element would affect the nucleation process of ??-Al(Mn, Fe)Sidispersoids by forming metastable Mg2Si(Hirasawa, 1975; Li, Zhang, & Chen, 2017a; Lodgaard & Ryum, 2000), metastable Mg2Si precipitated during heating process and promoted the precipitation of ??-Al(Mn, Fe)Sidispersoids, moreover, Mg provided solid solution strength for AA3004 alloys(Li et al., 2016). Si increased the volume fractionof ??-Al(Mn, Fe)Sidispersoids(Muggerud et al., 2013)and decreased the size of ??-Al(Mn, Fe)Sidispersoids(Li, Zhang, & Chen, 2017b). With the addition of Mo, the size of dispersoids became finer with a higher volume fraction, the volume percentage of dispersoid free zones was reduced. Elevated temperature yield strength and creep resistance improved due to Mo addition (Liu, Ma, & Chen, 2017).However, the effect of Crelements on microstructure and mechanical properties of AA3xxx alloys were rarely reported."

Jan 1, 2018

By C. H. Bucknam

Net carbonate value (NCV) characterization methods for acid generation potential measurement originated from studies on the Carlin Trend during the 1990's and have been subsequently standardized through cooperation of the Acid Drainage Technology Initiative Metal Mining Sector and the American Society of Testing and Materials International. The paper describes the evolution and standardization of the NCV methods, the importance of mineralogy in interpreting the results and application of the methods to implementation of the Global Acid Rock Drainage (GARD) Guide.

Jan 1, 2011

By Robert J-M Ethier

"Sequential blasting has been introduced at Mines Gaspe to reduce the harmful effects associated with the instantaneously primed blasting method. Three stages of modifications had been tried to improve this method: trials of a rectangular pattern instead of the square one, trials of lengthened hole collars at the perimeter of the blast and trials of increased inter-row delay intervals from 35 to 50 ms. Results showed that improvements to the instantaneously primed blasting method were limited by the probability of increasing the number of bootlegs.Doing these modifications allowed the definition of a general approach to improvements before the sequential blasting method was introduced. This general approach included: planning of the mining sequence, following up on the drilling, loading and tying-in of each blast, compiling and evaluating blast results, comparing results from one bench to the other and moving along with one change at a time. This approach has permitted the successful introduction of the sequential blasting method in two steps: trials of blast by rows of delayed holes and trials of hole-by-hole blasts. The optimum result has been analyzed by high-speed camera and by computer blast simulations, The actual optimum sequential blast is obtained with a CORDLINE priming system using period 15, permitted in a large drilling pattern, with an intersequences delay interval of 230 ms and an inner-sequences delay interval of 50 ms.While these modifications were being introduced, a careful study of the drilling and blasting costs was made, which showed a sharp reduction of drilling cost per tonne. Even though there was an increased use of packaged slurry the blasting cost per tonne also dropped. The reduction in cost per tonne was explained by the fact that the average energy factor was maintained while the blasting pattern was expanded.The sequential blasting method, successfully introduced at Mines Gaspe, permits blasts of better quality, reduces the drilling requirements by more than 30% and helps to achieve improved productivity while minimizing costs."

Jan 1, 1984

By R. Alarcón Sch., R. Abel F.

For many years, copper cathode quality has been a priority for end consumers, since it affects the variety of products that can be obtained from them. From the beginning, physical and chemical quality of the wire bars was controlled, as this product was used to obtain wire rod and other forms of copper by wire drawing. At that time, all the electro refined cathodes were melted and casted as wire bars. Subsequently, in the 80’s, with the introduction of continuous casting furnaces, it was possible to directly produce wire rod from cathodes. From then on, cathodes quality standards were consistently increased, by the introduction of uniform criteria, among which we can identify ASTM and British Standards as well. Also, producers began to use more demanding internal standards than the existing specifications, in order to differentiate their cathodes as high quality products among customers. Today the physical aspect of cathodes, including nodules, cracks, sulfates, or others, is the first element used by end customers to assess their quality. This paper aims to show a brief vision of the evolution of quality specifications for products used to manufacture copper wire. INTRODUCTION From the beginning of refined copper production for industrial purposes, mandatory minimum quality conditions were established. These quality conditions were used as the main element to determine prices and discounts of the respective sales contracts. Reviewing the copper development history, we can appreciate that its quality requirements had been constantly evolved, so that currently refined copper has an extremely high quality standard, that allows its direct use in the production of ultra-thin cables and other products applied in the industry. In each stage, refined copper production has fostered the development of technology used in their treatment. Similarly, cathode processing technology has been evolving to minimize treatment costs in order to generate a wire rod for several uses, ranging from power cables to super conductors. In this sense, to the already known type of fusion processes of the Southwire or Asarco type (capacities over 80 kt / year), wire rod production processes of the Upcast or Rautomead type (capacities between 20-50k t / year) have been added. They immediately deliver oxygen-free wire rods. In both cases, we can conclude that the clients' requirement had evolved from a chemical criteria focus, to considering more subjective aspects, such as visual control as the first stage of inspection.

Jan 1, 2019

By J. A. Eisele, D. L. Pool

"The Bureau of Mines has developed a particle agglomeration technique to improve the flow of leaching solution through heaps of low-grade gold-silver ores which contain clays. Benchscale experiments and industrial practice have shown that the percolation rate of cyanide leaching solution is greatly enhanced by mixing the ore with Portland cement as a binder, moistening the mixture, mechanically tumbling to form agglomerates, and aging before heap building and leaching. A slight modification ofthe technique allows its application to precious-metal-bearing tailings, which cannot normally be treated by heap leaching because they are too fine. IntroductionMany low-grade gold and silver deposits and tailing materials from former mining operations in the western United States are potential sources for precious metals. These sources are too low grade or too small to support the capital cost of a conventional cyanidation plant but have stimulated the development of lowcost procedures, such as extraction of the precious metals by heap leaching with cyanide. The Bureau of Mines has investigated methods to improve the recovery ofgold and silver by heap leaching these low-grade materials.For heap leaching to be successful, the crushed and stacked ore must have good permeability so that uniform distribution of the cyanide leaching solution through the heaps can be achieved. Some of the most difficult gold and silver ores to treat by heap leaching are those containing excessive amounts of clays, or fines generated during crushing. Excessive amounts of slimes, generally minus 50-micrometre or 270-mesh Tyler sieve size particles, in the heap feed will slow the percolation of the leaching solution, cause channelling, or produce dormant or unleached areas within the heap, resulting in long leaching periods and low extractions. In extreme cases, the clays or slimes can seal the heap and cause the leaching solution to run off the sides of the heap rather than through it."

Jan 1, 1987

By James F. Archibald

A research effort has been undertaken, under WSIB sponsorship, to characterize the support capabilities of conventional and innovative spray-on lining materials for mitigating dynamic failure effects created by simulated rockbursts. Conventional spray support media, such as shotcrete and fibrecrete linings, and a variety of new spray-on lining materials (TSL?s), typically polymer-type thin coatings, were subjected to simulated rockburst influence. For baseline comparison, conventional rockbolt and boltand- mesh support products were also evaluated. Observation of lining performance was undertaken through completion of field scale support and rock detonation trials. Controlled blasting tests were conducted at the Queen?s University Explosives Laboratory to examine the effectiveness of the variety of surface coating agents for modifying dynamic rock spalling processes. All tests were performed upon largely undisturbed and homogeneous rock materials in highly repeatable fashion. Both conventional and innovative TSL-type surface lining materials were subjected to ?rockburst? exposure in rigorously-controlled blast trials. All blasts were observed seismically and photographically to provide detailed information concerning rock motion, surface fracturing, ejected fragment motion and support liner survivability characteristics. These material comparison trials were performed to assess the relative effectiveness of a wide range of currently-available area support techniques for suppressing hazards associated with dynamic rock ejection. The results of this study validates that thin, sprayon linings may be equally as effective, and often better, than conventional support materials at mitigating rockburst or like damage in highly stressed mine environments.

May 1, 2003