Search Documents

By D. F. Kidd

Introduction In a companion article, Surveys at Great Bear Lake, 1931, R. C. McDonald has described the general character, topography, and climate of the Great Bear Lake-Coppermine River area and the main means of access (l). The present paper will largely be confined to the geological features of the district. In the last two years, the rocks of the region have received considerable attention, and papers including references to .the geological succession have been written by Knight(2), Duncan(3), Norris( 4), Reid(5), Cameron(6),and Kidd(7). The writer confined his field-work during the 1931 season to the district between LaBine point and Hunter bay and northwest to the head of McTavish arm. Brief trips were made down the Sloan river from McLaren lake, 25 miles northeast of Hunter bay, to that place, to Dowdell (Sixty-six) point, the south point of Echo bay, and to the region north of the Dismal lakes and west of the Coppermine river. The inner part of Echo bay, which is the area discussed by Reid and Cameron, has not been seen by the writer and the geology there will not be discussed.

Jan 1, 1932

By W. L. Stuewe

The Dominion Steel and Coal Corporation requires enormous quantities of bricks each year for its Sydney steel plant operations. Clay brick of all types are purchased, while silica brick is made in the Company's plant at Sydney. A description of this plant was given in a paper presented by H. B. Gillis and F. C. Morrison at the 1938 Annual General Meeting of the Institute. The rock used to make silica brick was for years obtained from a quarry at Leitches Creek, about eighteen miles from Sydney. Due to the gradual deterioration of this deposit, the Corporation was forced to look for other sources of supply. In 1945, the problem was presented to the Nova Scotia Department of Mines and, through the efforts of Dr. A. E. Cameron and Mr. J. P. Messervey, an examination was made of a silica-rock deposit some six miles northwest of Yarmouth, N.S. Preliminary samples proved satisfactory, and arrangements were made with the Department of Mines to ship to the steel plant at Sydney a fifty-ton car load for the purpose of further testing. Brick made from this sample shipment stood up very well in the furnaces. At the same time, two hundred and fifty tons of silica rock from a deposit at Lac Bouchette, Que., were purchased from the Industrial Silica Corporation, and brick made from this rock also was found suitable for our requirements. Comparative transportation costs, however, led to a decision to open the Yarmouth deposit. The silica rock, or quartzite, of this deposit outcrops at Chegoggin point along what is known as the 'Pembroke shore', a northerly trending section of the coast-line at the extreme southwest of the Province, in Yarmouth county. The country here is fairly flat, with elevation averaging about twenty feet above high tide, and is for the most part mantled by a growth of brush and some scrub trees, chiefly small fir. Bed-rock is generally concealed beneath three to four feet of clayey soil, but scattered outcrops of the quartzite indicated that a band of this rock, some 260 feet wide, extended inland in a northeasterly direction from Chegoggin point at least to Utleys lake, a distance of about three miles.

Jan 1, 1947

Risk management has taken on renewed vigor since the economic crisis of the late 2000s. The resources of governments, individuals, and corporations are being stretched to a point where only the most promising projects move forward. Risk management is a crucial part of the decision making process, yet it remains a broad term that includes disciplines from engineering to finance. A collaborative effort will be necessary to ensure that the most auspicious and appropriate projects are the ones moving forward. Risk management can be quantified to an extent by comparing the likelihood of an instance with the result of consequence of the instance occurring. In this manner it is possible to assign risk factors to instances and ultimately, begin to associate monetary value to the instance. Carbon sequestration is an emerging field that has a number of unique challenges. Risk management and mitigation must be an integral part of the overall picture. This begins with the planning and design phase, continues through implementation and production, site closure, and does not cease until termination of liability. The ability of carbon sequestration projects to successfully assess, mitigate, and recover from leaks will be a decisive characteristic of overall success. The costs of mitigation and failure will need to be analyzed on a test level, but will still need to be reliable enough to extrapolate to a commercial level operation. This paper will build a risk management profile based on case studies and field tests in Tennessee and Virginia. These tests are scheduled to commence in late 2013 and consist of small-scale injection tests in unconventional storage reservoirs with an emphasis on enhanced coalbed methane (ECBM) recovery and enhanced gas recovery. The ultimate goal will be to provide a clear and concise direction to move carbon sequestration from the test phase to commercial scale. While it is necessary from a risk management perspective to analyze all risk points, the scope of this paper will focus on pre-injection risk assessment for carbon dioxide (CO2) leakage potential. Despite the differences between the two tests, CBM compared to shale among other differences, a framework for analysis and mitigation can be developed pertaining to leakage risk. The probability of each type of failure will be assessed and analyzed, and plans to mitigate or reduce these risks will be reviewed.

Aug 1, 2013

By Humphrey Dean

"Canadian mining companies now operate numerous Koepe-type friction hoists in a variety of different shafts, most of which have a depth in excess of 3,000 feet. Rope performance reliability is an absolutely essential ingredient of most installations and, for this to be provided, a more comprehensive understanding of rope reactions to applied stresses is required.It is the intent of this paper to illustrate for the operators the importance of the critical stresses encountered and to provide a maintenance program designed to circumvent potential difficulties."

Jan 1, 1970

By K. A. Clark

SEPARATION of the oil from the bituminons sands of the Athabaska area of Alberta has been a subject of study by the Research Council of Alberta. The results of the study have been published in the Annual Reports of the Council. However, the last Annual Report in which there is mention of bituminons sand separation is that for 1934. The attention that is being directed toward the bituminons sands at the present time calls for an up-to-date summary of the work of the Research Council of Alberta on the hot-water separation process. STATEMENT OF FUNDAMENTALS OF HOT-WATER PROCESS Studies of the hot-water separation process have been largely empirical in nature. The objective sought has been a complete recovery of oil from the sand in the form of a separated oil which, itself, is free from mineral matter. Various procedures have been tried in the hope of attaining this objective and a very considerable mass of observations and background of experience have been acquired. lt is rime that a theory for hot-water separation should commence to emerge. As a start toward the formulation of such a theory, the statements which follow regarding the constitution of bituminons sand and its reactions with water and air are presented. It is not pretended that they are entirely correct, but it is believed that they lie not far from the truth. (1) Bituminons sand is an aggregate of sand, clay, oil, and water. The sand consists mainly of quartz particles of 100 ta 200 mesh size and smaller, but also of particles of other minerais including mica, rutile, ilmenite, tour-maline, zircon, spinel, garnet, pyrite, and lignite. Clay occurs interbedded with the bituminons sand, of which, also, it is a constituent. lronstone nodules of all sizes up to eight inches in diameter are likely to be present in the bituminons sand beds. The oil is viscous, naphthenic, and of a specific gravity slightly greater than that of water. The oil content ranges up to, and sometimes even exceeds, 17 per cent by weight. Rich bituminons sand from beds not invaded by water has a water content of 3 to 5 per cent by weight. The water is probably present as a film around the sand particles. The oil surrounds the moist sand grains as an envelope. (2) Water wets quartz and other siliceous minerals more readily than does mineral oil. Consequently, water tends to displace the oil film surrounding the quartz and other siliceous particles when the bituminons sand is mixed with water. Whether the oil is completely displaced depends on the properties of the water. That is to say, the materials dissolved or suspended in the water modify its wetting properties.

Jan 1, 1944

By O. A. Carson

Introduction Although the equilibrium conditions of the copper-tin alloys have been the subject of a ?great amount of research, the equilibrium diagram is still in doubt. The first systematic investigation of the series was made in 1894 by Le Chatelier, who published a freezing-point curve. In 1895, Roberts-Austen and Stansfield published the complete liquidus and partial solidus curves, which they modified somewhat in 1897. Their liquidus as given in 1897 is essentially that accepted today (Figure 3). Haycock and Neville also published a liquid us curve in 1897. In 1898, William Campbell published a series of micrographs showing the changes in microstructure which accompanied the thermal changes of Stansfield? s diagram. The classic work on the bronze series was published by Heycock and Neville in 1903. Their diagram was based on both thermal and microscopic evidence, and is the first for this series of alloys which can be considered nearly complete. Further, it was the first bronze diagram in which any attempt was made to apply the phase rule in the interpretation of the thermal and microscopic results. That portion of Heycock and Neville's diagram covered by the present work is reproduced in Figure 7.

Jan 1, 1929

By McNeely DuBose

INTRODUCTORY PROSPECTING for aluminum has always been, and still is, a peculiar combination of the technical with the physical approach, and 1 want to explain my conception of the term 'prospecting' when applied to aluminum, which differs in some respects from the ordinarily accepted idea of prospecting. In the early days of gold mining, prospecting was a search in the hills and the river beds for the metal, not for its chemical combinations. And so it was in the early days of aluminum, with the difference that the search for the metal was carried on, not in the hills and dales, but in chemical laboratories. Aluminum is never found in the elemental state and at that time the metal bad never been seen, but scientists of that day bad forecast that such a metal must exist and in 1807 Sir Humphrey Davy went so far as to give this unseen metal a name, aluminum, from the Greek word alumen. This word applies to our alum, and it was from alum that Davy sought to produce the metal. It is strange to think that, in laboratories throughout England and on the continent, prospecting for aluminum was busily under way by men who had never seen the metal they were searching for. Their situation was something like that of the fisherman and the 'big one' that got away. They could describe the metal, give its exact weight, and even name it, but they could not produce visual evidence of its existence. Eventually, however, the efforts of the scientist 'prospectors' were rewarded and in 1826 the metal was actually produced, possibly first by Wohler, though Oerstedt, a Danish chemist, is usually credited with the achievement.

Jan 1, 1951

By Staff

Introduction As the Sherritt Gordon property is still in the development stage, . it is rather difficult to write a proper account of the mining methods and milling practice that will be used. While the general scheme of operation will remain the same, there will undoubtedly be many minor changes to meet special conditions which we cannot forsee at the present time. Most of the work accomplished to date has followed the usual routine of preliminary development in the Canadian North. However, we have learned a few things which might be of use to others operating under similar conditions. The most important of these is the saving in power cost made possible by the use of Diesels as against steam power when using wood fuel, and the movement of freight by tractors when rail transportation is not available. Location The property i6 located about 90 miles north of The Pas, or 40 miles northeast of the Flin Flon mine. A branch line from Cranberry Portage, on the?C. N. railway, between Flin Flon and The Pas, connects the property with the outside.

Jan 1, 1930

By J. A. Chamberlain

DURING a recent trip across Canada and parts of the northern United States, the. writer examined some forty mine models. Construction -details and the uses to which the models were being put were outlined in a report to Eldorado Mining and Refining, Limited, and a specific model was proposed on the basis of the Company's particular needs at their Beaverlodge operation. It was felt, however, that portions of the report would be of some value to anyone contemplating building a mine model. For this reason, a synopsis of some of the more important aspects of the problem is presented here, together with a suggested model type that appears to have wide application. Thanks are due not only to Eldorado for permission to publish the following material, but also to the many mine personnel across Canada who allowed the writer to examine their models and gave freely of their time in discussion.

Jan 1, 1958

By A. K. Ratte, C. M. Brown

"IntroductionIn autogenous mills, grinding of the ore feed is accomplished by the direct action of the variously sized rocks making up the feed on each other and the mill interior. Size reduction is achieved without the addition of grinding media foreign to the mill feed, differing in this respect from rod, ball, and pebble milling. The term ""semi-autogenous"" has entered common usage in the industry to describe autogenous mills to which supplementary grinding ball additions are made to increase the rate at which size reduction of the mill feed occurs, beyond that achieved solely by the action of rock on rock. In a semi-autogenous grinding (SAG) mill, 50Jo to 10% of the mill volume may be occupied by grinding balls, whereas a range of 25% to 45% is more usual in ball milling.The comminution of mineral ores using ""conventional"" techniques has been described in previous papers. In conventional operations, size reduction of mined ore, and liberation of the valuable mineral content, is typically accomplished using flowsheets employing two to four stages of crushing. Crushing is followed by one to three stages of grinding and classification using various combinations of rod, ball, and pebble mills. This paper describes operations employing autogenous or semiautogenous grinding as the principal stage in the comminution process. Primary crusher discharge, or in some instances run of mine ore, is fed directly to an autogenous or semi-autogenous grinding circuit. Final product sizing may be accomplished in a single grinding stage, the mills operating in closed circuit with classification equipment, or in several stages using autogenous and semi-autogenous mills for primary grinding, and ball or pebble mills for secondary grinding. In several operations a portion of the primary mill discharge is crushed in an intermediate comminution step, these circuits being called autogenousball- crusher circuits (ABC). Many different flowsheets exist, but common and important to most are crushed ore stockpiles, reclaim feeder and mill feed conveyor systems, pumps, screens, and classifiers. Autogenous grinding is employed in both wet and dry processes, although today wet predominate."

Jan 1, 1989

The purpose of this paper is to present the methods used in ground water control and the considerations that affected the development of these techniques. Production at Knob Lake is currently proceeding at depths which may be as much as 200 feet below the original standing water table. In order to produce a more saleable product and to improve operating and maintenance conditions, it is necessary to depress the water table below the mining level. Considerable success has been achieved by drilling deep wells in strategic locations and installing vertical tur-bine pumps at depths of up to 400 feet. This method is especially suitable for operation under severe winter conditions and has reduced the detrimental effects by a far greater extent than other methods of water control, Spring runoff is handled in open sumps, but all other water from four mines, with flows exceeding 16,000 g.p.m., is pumped all year 'round from about thirty-five wells. THE Knob Lake operation of the. Iron Ore Company of Canada is located on the Quebec-Labrador border, 320 miles north of Sept-lies, a seaport

Jan 1, 1965

The purpose of this paper is to present the methods used in ground water control and the considerations that affected the development of these techniques. Production at Knob Lake is currently proceeding at depths which may be as much as 200 feet below the original standing water table. In order to produce a more saleable product and to improve operating and maintenance conditions, it is necessary to depress the water table below the mining level. Considerable success has been achieved by drilling deep wells in strategic locations and installing vertical tur-bine pumps at depths of up to 400 feet. This method is especially suitable for operation under severe winter conditions and has reduced the detrimental effects by a far greater extent than other methods of water control, Spring runoff is handled in open sumps, but all other water from four mines, with flows exceeding 16,000 g.p.m., is pumped all year 'round from about thirty-five wells. T HE Knob Lake operation of the. Iron Ore Company of Canada is located on the Quebec-Labrador border, 320 miles north of Sept Iles,

Jan 1, 1965

By John Loop, W. A. Gibbins, Donald D. Hogarth

"Introduction Background The Frobisher voyages of 1577 and 1578 were organized by the Cathay Company for the express purpose of finding and mining gold ore. Since publication of the Baffm expedition of Charles Francis Hallill, the location of Kodlunarn or Countess of Warwick Island, the headquarters of Frobisher's third (1578) voyage, and focal point of the largest Arctic voyage of all time, has been known to the world. Through Hall we also know the location of the Countess of Warwick Mine on Kodlunarn Island. However, the exact locations of the other mines are not known. Of the ""ore"" we know little. Pieces of the original ""black stone"", once as large as ""a half-penny loaf' have now disappeared altogether. Specimens collected at random from the repository of shipments in England and from loose rock on Kodlunarn Island were termed, respectively, ""hornblende pyroxenite"" and ""amphibolite"" and from a locale about 200 yards from Kodlunarn as (hornblende) ""pyroxenite""121. However, it is uncertain whether these specimens are representative of Kodlunarn or of the other mines, although Blackadar131 notes that, in the northern trench of Kodlunarn, biotite gneiss contains lenses and bands of amphibolite. The ""gold"" itself is even less well defined. It has long been accepted that gold was virtually absent in Frobisher's ore. The ""gold"" has been termed pyrite, biotite and both biotite and pyrite together. Even t h e word "" marquesset"" , which appears and reappears in contemporary descriptions, is nebulous and is defined as ""a stone participating in the nature of some metal, yet in so small quantity, that the metal cannot be melted from it"" (0.E.D., definition of 1616)."

Jan 1, 1999

By M. Piard

The scarcity of literature referring to mines in the Rockies has compelled the writer to co-ordinate information and advice taken at the very source. Help was gladly given by active inspectors and mine bosses. Although the field is unimportant at the present time, due to its distance from markets for raw coal, it is quite worthy of the attention it is receiving from two continents; for, with the commercial synthesis of liquid fuels, it would become the largest fuel laboratory in the world, provided, of course, that freight cost drops to a low comparative level. As explained below, there are no obstacles to economical and safe operation under anything like the typical outcrop shown in Figure 1. Although coal dust is probably more dangerous in the Rockies than anywhere else, the damp outcrops afford means of control. The abundant gas may be bled to the open air, and the rigid roof will settle gradually under a wide span of opened outcropping. The Panel Retreating Wall The Measures: Coal measures having an attitude similar to that shown in cross-section in Figure x are characteristic of the active coalfield on the Alberta side of the Rockies, and they are also found on large tracts of undeveloped land west of the divide. The small anticlines, not shown in the cross-section, do not affect the progress of a pillar line, provided their crests are connected to the atmosphere by drainage bore-holes.

Jan 1, 1928

By D. Nower

"The supply of copper is expected to be at a large deficit in 2012. To recover from these deficits mining companies are required to maximize production and there is no better way to accomplish this than to optimize the use of their mobile mining equipment fleets. To optimize these fleets, each equipment type has to be monitored in its own unique way. Automation would not only improve production, but also minimize the safety risks and eliminate planning errors. The automated vibration monitoring of multiple systems on the shovel can determine the machine’s condition at all times. This reduces unplanned downtime and keeps critical shovels in production. This paper will discuss the details of how shovels can be successfully monitored, continuously. INTRODUCTIONP&H Mining, part of Joy Global, is the world’s largest manufacturer of above-ground mining equipment. Its electric rope shovels, such as Figure 1, with capacities up to 115 tons (104.3 metric tons), are used for high production loading in surface mines; its draglines, such as Figure 2, have bucket capacities to 160 cubic yards (122 cubic meters). P&H also produces blasthole drills, mobile mining crushers and other essential mining equipment. Headquartered in Milwaukee, WI, the company does business on every continent, except Antarctica. ECONOMIC FACTORSDue to the global demands for metals and power, mines are required to operate at full capacity. Mine operations cannot afford any critical assets to shutdown unexpectedly; depending on the ore type and quality, downtime for a single shovel can be as much as $300,000 per hour.Electric rope shovels are one of the most critical assets in open pit mining. They are very large, complex machines with DC or AC motors, multiple reduction gearboxes (some of them complex planetary) and multiple large rolling element bearings. This complexity, combined with the tough 24/7 service, results in too much unplanned shovel downtime, which can affect the entire downstream process."

Jan 1, 2012

By L. Don Leet

Abstract Earthborne vibrations from blasting and other sources, including rock bursts, can now be recorded effectively. The nature and magnitude of vibrations from various sources have been investigated and certain applications of the knowledge thus gained have been made. Vibrations from blasting have been measured on special equipment over a range from an electric blasting cap at a few feet, through the largest quarry shot in history to date ( 1,-362,985 lb.), to the first atomic bomb, in uew Mexico on July 16th, 1945. Laws relating amount of explosive to amount of vibration at different distances have been developed and tested. Special studies have been made of the effects of vibrations on buildings, particularly from the standpoint of possible structural damage. Recorded vibrations are used to study the effects of modern short-period delay shooting. It ?has been found that short-period delay firing is extremely effective in reducing vibrations under the right conditions, but with certain limitations. In quarry shooting, there appears to be a minimum number of holes below which vibrations are not appreciably reduced by short-period delay firing. In several instances this minimum has been near 7. Vibrations in the ground from rock bursts and the effects of mining in stresesd ground have been studied both underground and on the surface in a search for a rock burst warning system. Introduction Earthborne vibrations from blasting and other sources, including rock bursts, can now be recorded effectively. Analyses of blasting records have been yielding increasing funds of information of practical as well as theoretical interest. The nature and magnitude of the vibrations have been investigated with special reference to their effects on structures.

Jan 1, 1951

By J. R. Andrews, R. P. Young, J. M. Reyes-Montes

"Microseismic monitoring provides insight into the location and extent of rock-mass fracturing induced by cave mining, enabling interpretation of the cave profile and validation of predictive numerical models. Source location uncertainties can lead to misinterpretation of the inferred characteristics of the fracture network. One principal source of uncertainty is the velocity model used to invert the location algorithm. Large-scale 3D numerical models of modulus changes across a caved mass can represent such complexities in the location algorithms, allowing more accurate interpretation of the microseismic activity. A Northparkes mine case study applies this advanced approach to microseismic data interpretation.RÉSUMÉ Le suivi microsismique fournit des renseignements sur la localisation et l’étendue des fractures de la masse rocheuse induites par l’exploitation par blocs foudroyés; cela permet d’interpréter le profil de la chambre foudroyée et de valider les modèles prédictifs numériques. Les incertitudes quant à la localisation de la source peuvent conduire à des mésinterprétations des caractéristiques inférés du réseau de fractures. Une des principales sources d’incertitudes est le modèle de vitesse utilisé pour inverser l’algorithme de localisation. Des modèles numériques tridimensionnels à grande échelle des changements du module d’élasticité à travers une masse foudroyée peuvent représenter de telles complexités dans les algorithmes de localisation, permettant ainsi une interprétation plus juste de l’activité microsismique. Une étude de cas à la mine Northparkes applique cette approche avancée à l’interprétation des données de microsismicité."

Jan 1, 2016

By I. M. Marshall

A review of technical literature covering Canadian mining emphasizes the advancement and changes that have been made in mining practice. However, current technical publications rarely outline basic principles or state definite rules that govern profitable mine operation. it may be argued that the broad principles of mining have long a go been outlined in various handbooks, text-books, and periodicals, and that these principles never alter. This is in great part true, but modern machinery, improved meta1-lurgical practice, and other advances, have in part modified these principles or changed the manner of their application. Many engineers hesitate to state specific rules, because it is so easy to quote an exception to a rules that any such statement appears to lose weight upon its very utterance. The exception to rules, and the reluctance to formulate rules, has forced such maxims as "the only rule in mining is the point of a pick," and "gold is where you find it". As an illustration of rules and their exceptions, one might quote the time-honoured maxim that a mill should not be built before a shaft has been sunk on a property in point of fact, Canadian mining history is replete with examples of wasted capital where a mill was built before a shaft had been bottomed. Y et this past year has seen a property enter profitable production whereon the building of the mill was started before the shaft was sunk. Instances such as this should not be accepted as evidence that a rule has been overthrown, but rather as an exception to the rule. The case cited pays tribute to the application of the diamond-drill combined with the correlation of sound geology. Incidentally, both these features emphasize a modern trend in the development of Canadian mining properties-a trend that is perhaps worthy of further comment. It is such trends that affect the principles of mining or modify their application. It is with such that this paper deals, at ]east in part. It is hoped that the statement of principles and the opinions herein outlined will be of sufficient interest to arouse discussion.

Jan 1, 1939

By Harry Wilton-Clark

Introduction Coal cleaning may be taken as meaning the separation of coal-as-mined into two or more fractions. Coal cleaning includes coal washing, together with any other means used in the ultimate preparation of coal prior to shipment (as coal) . The method of coal cleaning devised for any given mine must be one which is based entirely on the economic results obtainable. The installation of a high-cost and complex washing plant, designed to produce a low-ash dean coal, at the highest possible recovery, may be unsound practice. A crude 'roughing' washer may be the best result of sound engineering and operating consideration, and in some cases coal cleaning should be confined entirely to preparation at the face. Consideration of complete costs, to the point where the coal is actually sold, may show that certain seams are workable or not workable. Of the seams found workable, extraction of the whole or parts of the seam may be decided on. The portion to be extracted may contain rock or bone partings, which must be removed. It may be good practice to mine the extra portion and remove the objectionable materials by surface washing; or it may be that such materials should be removed underground, even at an increased mining cost. For instance, in some of the steeply pitching seams of the Alberta Crow's Nest Pass district, the removal of bone and rock at the face may be almost impossible under the usual 'up the pitch' or 'angle' mining methods, but possible by mining across the pitch so that the material to be rejected can be removed and gobbed. Again, if a complete seam is being extracted, investigation may show marked differences between top coal and bench coal, and if sufficient mine cars are being loaded from a chute at one time, the fact that such a place is working top or bench coal at the time may be reflected by peaks in ash content or size proportions at the ripple. It may be very effective coal preparation to smooth out such peaks.

Jan 1, 1934

By L. M. Dwarkin

Introduction Avital factor in the success of any coal mining operation is the method of roof support employed. A coal seam in? place has been described as the filling in a geological sandwich and the process of mining as the art of snatching the filling from the midst of the sandwich. The difficulty of this task can be appreciated -in the realization of the tremendous weight bearing on a coal seam due to overlying strata; a weight that can exert pressures of several thousand pounds per square inch. Over the years that mining has been carried on, methods have been evolved by arduous trial and error, making possible the successful extraction of billions of tons of coal. However, these time-proven methods are not enough. The constant demand for faster and cheaper production, the necessity of mining under increasingly difficult conditions, and the requirement for higher standards of safety, call for ever better and more efficient roof support. A recent and very promising development in answer to this need is that of Roof Bolting. Roof Support in General Before proceeding to the subject proper, a brief discussion of the older roof support methods is of value in illuminating the difficulties involved and the problems to be solved.

Jan 1, 1951