Search Documents

By Tadeusz W. Wlodek

THE known phenomenon that a test-piece of ferro-magnetic steel is magnetic after it has been broken in tension indicates that, while it is being loaded, the steel acquires magnetic properties. In the present investigation of the influence of the stress on the magnetic flux, repeated pulsating stresses of increasing amplitude, varying from zero to the maximum tensile value, i.e., pull-pull loading, were employed. The specimens were prepared from two types of carbon steel and two of alloy steel. The magnitude of the magnetic flux was determined indirectly. The voltage and mode of variation of the electromotive force induced in a coil surrounding the stressed steel specimen were measured as an indication of the varying magnetic flux within the specimen. Curves representing the electromotive force induced by the varying magnetic flux show that as the tensile load increased so also the magnetic flux increased, with a corresponding increase in measured e.m.f. At a certain stress there is a sharp bend in the voltage curve (point Win the diagram, Figure 5); this critical stress corresponds very closely with the yield stress (0.2 per cent permanent strain). Beyond this point, slight increases in the stress produce large increases in the voltage. The wave form of the e.m.f. was registered on an oscillograph. Analysis of the curves so obtained demonstrated the necessity of continuing these experiments, in order to determine the type of induced wave form associated with various types and amplitudes of stresses. In these experiments, the shape of the stress wave was sinusoidal, although the shape of the induced e.m.f. was sinusoidal only up to a certain load and became more and more complex above this load.

Jan 1, 1944

By Timothy R. Eby

"The Wabush Mines project was formed in 1956 to develop a large iron ore property in Western Labrador. The town of Wabush along with the mining and concentrating facilities are located 640 air miles from Montreal, and 734 air miles from St. John's. The operation has been in production since late 1964.While mining and concentrating operations are located in Labrador, the pelletizing facilities are situated 275 miles south at Sept-Iles, Quebec. Dedicated in 1965, Wabush produces six million tons of high quality iron ore pellets annually. The company employs 1, 550 people at Wabush and the Pointe Noire plant at Sept-Iles.Wabush Mines is an unincorporated joint venture of three companies -The Steel Company of Canada, Dominion Foundries and Steel Ltd. and the remaining 58% by the Wabush Iron Co. Ltd. Wabush Iron Co. Ltd. is in turn owned by six companies: The Youngstown Sheet & Tube Company, Inland Steel Company, Interlake Inc., Wheeling Pittsburg Steel Company, Finsider International S.A. and Pickands Mather & Company which is also managing agent.The town of Wabush is set in a remote part of Northern Canada accessible only by rail and air transportation. But this in no way has hindered the growth and development of the area. Modern housing units, shopping facilities, airport and of course, recreational facilities are all patt of every day living amenities, an accepted aprt of southern communities, but quite unique for northern isolated mining localities."

Jan 1, 1978

By Renaud Adams, Vladimir Salatic

"The El Mochito Mine located in Honduras, Central America, has produced lead, zinc and silver in concentrates since the 1950s. The paper discusses changes made in both lead and zinc circuits to reduce costs while maintaining production during the recent period of low metal prices.The intent of this paper is to show that sometimes thinking “outside the box” is beneficial for progress. Also, in striving for better metallurgical results we should not forget the basics of flotation. Sometimes the latest trends may not be applicable to the ore we are treating and may not meet the operating cost constraints.A major beneficial impact on El Mochito metallurgy was achieved when the overall grind was coarsened, eliminating the significant percentage of slimes. Switching from two parallel twostage grinding circuits to one circuit with three-stage series grinding has resulted in a significant reduction in power and steel consumption. With minor layout/reagent modifications, both lead and zinc circuits gained not only in retention time but as well in producing better grade products.Of course, the challenges are still there; they exist and only with the full support of operational data collection and metallurgical laboratory investigation success can come. That is why, we as professionals, can never stop in trying to make the most of what we have.INTRODUCTIONThe El Mochito Mine is owned by American Pacific Honduras S.A. de C.V. (AMPAC) a subsidiary of Breakwater Resources Ltd. Of Toronto, Canada. The mine is located in western Honduras, approximately 220 kilometers northwest of the capital city, Tegucigalpa and 90 kilometers south of the country’s second largest city, San Pedro Sula. The mine began operating in 1948 and to date has produced more than 19 million tonnes grading 240 g/t Ag, 3.5% Pb and 7.4% Zn. Production in 2005 was 700,190 tonnes grading 87 g/t Ag, 1.85% Pb and 6.61% Zn.Decreasing metal content in the ore followed by the lowest zinc price on the market in the last 15 years (see Figure 1) has reduced the cash flow and endangered to stop the operation."

Jan 1, 2007

By C. S. Parsons

Custom milling-plants have been operated successfully for a great many years on this continent. One of the outstanding examples in the United States is the Golden Cycle mill at Colorado Springs, which mills the gold-telluride ores from the Cripple Creek district. In eastern Canada, the Northern Custom Concentrators, Limited, at Cobalt, successfully treated the cobalt-silver ores of that area for a number of years. Flotation plants have entered the custom field in the past few years. The building of flotation concentrators to treat ores on a custom basis indicates the advance which has been made in flotation. In fact, three years ago it was considered almost impossible to treat successfully a mixture of miscellaneous ores by flotation. The methods used at that time were considered so delicate that any change, even in a single ore, would usually result in decreasing the effectiveness of the separation. Today we find four large custom flotation plants in the United States and one in Canada for treating complex lead-zinc ores from many different localities. The advent of these mills was brought about by the serious problem confronting the lead-smelting plants due to increasing amounts of zinc in the ores presented for treatment. It was necessary to penalize the mines shipping high-zinc ores. The penalty is justified, because high zinc in the lead blast-furnace charge not only decreases the tonnage of the furnace but increases the amount of flux necessary, as well as increasing the metal loss in the slag. It has been estimated that in the Salt Lake valley alone, 75,000,000 pounds of zinc was lost in the slag-dumps from the operations of three large lead blast-furnace plants. It has also been estimated that $150,000 worth of additional flux was required to slag this zinc. It was to avoid at least a part of this wste and to help maintain an ore supply that custom flotation concentrators were built by the smelters.

Jan 1, 1928

By Horst Konig

This paper illustrates that, with the application of new processes, smaller steel plants using local raw materials can be economical and advisable. It also introduces the problems connected with the direct reduction processes, which use non-coking coal or gas as reducing agents, and which are employed in connection with conventional reduction to produce excellent results. Electric smelting is also discussed, and some practical examples of operating plants are given.

Jan 1, 1970

By P. G. Rueffel

"Natural deposits of sodium sulphate are the result of normal geological processes. They are world-wide in occurrence and are found in depressions in arid and semi-arid regions. Primarily, the sodium sulphate deposits of the prairies are post-glacial and differ from rock salt deposits, which originated from connate water (fossil sea-water). Sodium sulphate on the Canadian prairies occurs as brine or in beds of intermittent and/or permanent crystals. Most beds are contaminated with various amounts of silt, sand and decayed organic matter. Soluble impurities such as chlorides, carbonates and bicarbonates of sodium and sulphates of magnesium and calcium are leached out from the soil of the surrounding run-off area of the deposits.In this paper, the origin of sodium sulphate, and the physical and chemical aspects related to the development of the Ingebrigt Lake deposit are dealt with. The problems of garnering raw material, and of refining and de-hydration are discussed, with emphasis on the Ingebrigt Lake plant. The utilization of the ""Total Power Concept"" in a sodium sulphate plant is described. The principal uses of sodium sulphate are also discussed."

Jan 1, 1968

By Rob Boom, Yasuyuki Tozaki, Frank M. Wheeler

Selection of a suitable site for a metallurgical plant is crucial for the success of the business case. For a brownfield project, with the decision to locate the project on a site with existing production facilities and activities, the selection of the site has been made. For a greenfield project, important economic and logistical considerations include proximity to primary and secondary resources and/or to the market, infrastructure, and access to energy and water. National and regional aspects, including the social license to operate, can be decisive in final site selection. Key to recruiting and retaining a labour force are proximity to urban areas, along with weather and health conditions at the site. Risk factors include site geotechnical parameters and topography, contamination, as well as probability and types of potential natural disasters.

Jan 1, 2015

By J. L. Collins

"Une recherche debutee en 1987 tente de cerner divers éléments ayant un impact sur la productivite miniére, de facon à améliorer la planification des operations souterraines. II a été possible de recueillir jusqu'à trente variables dans sept opérations minières differentes du Nord-Ouest québécois. Cette présentation rend compte de quelques résultats préliminaires obtenus à l’une d'entre elle. Entre autres, elle montre comment une association entre une analyse de régression multiple et un logiciel d'optimisation (OPTIMUL) peut servir à une application particulière de la planification d'une opération minière du Québec. Plus spécifiquement, la présentation montre comment une quantité appropriée de ANFO et de TOVEX peut maximiser la quantilé de minerai cassé, minimiser les couts de sautage ou encore minimiser les coûts d'explosifs par tonne de roche cassée, en se basant sur une série de contraintes réalistes provenant de la mine.ABSTRACTA study, underway since 1987, tries to evaluate factors affecting mines' productivity. Information has been collected from seven underground mines in Quebec and this paper shows preliminary results from one. In particular, it shows how a combination of multiple regression analysis, mathematical programming and a set of realistic mine constraints can be used for a particular application of mine planning. More specifically, the paper shows a parallel between maximizing production of tons of broken are, minimizing explosives costs or minimizing the costs of explosives per ton of broken are by an appropriate selection of ANFO and TOVEX quantity of explosives. Finally, the paper shows that minimizing the costs of explosives per ton of broken are is the best alternative to follow providing a special optimization program can be set up."

Jan 1, 1990

By J. C. Nicholson

The "V" system was first introduced by the West Virginia Coal & Coke Company at their No. 9 mine, Norton. Norton is a small mining village on the B. & 0. railway, about seven miles from the town of Elkins. This year, accompanied by G. D. MacDougall, I visited this mine to obtain first-hand information regarding this modem system and to determine its adaptability to conditions in Nova Scotia. The following is a brief account of my observations. The seam that is being worked is known as the Lower Kittaning, which, at this point, has an average thickness of 7 feet. This includes a band of hard clay varying in thickness from 8 to 14 inches, which occurs about 2 feet from the pavement, also 8 inches of inferior coal at the roof. The latter is not recovered, which leaves to be mined about 5 1/2 feet of clean coal. The roof is slate and shale for the first 30 feet, followed by 40 to 60 feet of sandstone; the total cover is from 80 to 250 feet thick. The seam lies very flat, with a dip of only 2 per cent., and, as the dip is toward the main entrance, it' is in favor of the load, also providing natural drainage for any water the mine makes. As the mine is not gassy, and there is no water to be pumped out, one can understand that mining conditions are practically ideal.

Jan 1, 1924

By Andrew J. Freyman, Graham T. Armstrong

"In September, 1968, a survey of operating mines in the Yukon and the Northwest Territories was undertaken to determine the role of Indigenes (Indian, Metis, Eskimo) on the mines, and the attitude of mine management to these employees. The operating mines in the Territories had (at that date) a total employment of 2,002 men, of which 91 (4.5 per cent) were Indigenes. Indigenes make up 45 per cent of the Territorial population (18 per cent in the Yukon and 63 percent in the Northwest Territories). The paper documents some of the problems associated with indigenous employment in mines. A study was undertaken to determine the role of Indigenes (Indians, Metis, Eskimos) in operating mines in the Yukon and in the North-west Territories. In addition to the mines north of the 60th parallel, the experience of several other Canadian mines was examined. The general picture obtained is considered to be representative of the Canadian mining industry."

Jan 1, 1969

By J. Ouellet

The design of hydrostatic liner for a deep potash mine shaft in Saskatchewan poses tremendous technological challenges. Technology has evolved to a point where one could consider a new innovative approach to hydrostatic liner design. But there is still a place for conventional technologies such as cast iron tubbings. As will be discussed in this paper, improvement to manufacturing process, installation procedures and even new materials can bring this technology to an excellent level of performance. With the spur of new projects in the potash industry of Saskatchewan, the authors worked in various shaft liner designs from the conceptual stage through to the construction phase. They were either directly leading the design work on some of these projects or acting as an external reviewer on others. Most of these shaft liner designs involved cast iron tubbing technology and ground freezing. The major challenge in sinking potash shafts in Saskatchewan is to go through a water-bearing ground formation under high pressure, known as the Blairmore or Manville fm. The only proven stabilizing technology for these formations is ground freezing. For a potash shaft, dry shaft conditions are highly desired, so a fully waterproof hydrostatic liner is required. All the existing potash mine shafts in Saskatchewan, except for two with composite steelconcrete lining, used the cast iron tubbing technology. Two new shaft tubbing liners have been constructed recently, one in the Athabasca Basin and one for a potash mine in Saskatchewan. When the authors began working on these new projects, what became quickly evident is that the technological knowhow for designing and constructing tubbing liners was no longer available within Canada and that the past construction methods used to sink tubbing lined shafts was obsolete. The tubbing liner for the shafts sunk in the sixties were designed either by German or British companies. In both of these countries only few tubbing lined shafts were sunk in last 40 years and the technology used in the sixties was not improved. There are only few countries where tubbing is routinely produced and installed: China, Russia, Ukraine and Poland. Out of these countries Poland is the one where this technology is the most advanced. The authors, working in close collaboration with engineers from Poland, attempted to rebuild this knowledge for the mining industry in Canada. This process involved thorough analysis of old technical reports, literature review and study of current polish design and construction practices as well as site visits of existing shafts. Through actual construction experience, some lessons were learned as well as ideas for improvements. In this paper, the authors will present a succinct review of design and procurement process. But, the practical aspects of the construction and installation methodology will be treated with more emphasis, more specifically the practice leading to good liner performance. Some of the poorly understood technical aspects of tubbing installation will be discussed more thoroughly and some currently accepted myths dispelled.

Aug 1, 2013

By H. J. Rowley

THERE are many varieties of limestone, but for the general purposes of the pulp and paper industry, two classifications are sufficient: (1) High-calcium stone, which should be quite free from impurities and contain not less then 90 per cent calcium carbonate. (2) High-magnesium stone, containing not less than 25 per cent of magnesium carbonate. Before proceeding with detail on the use of limestone and lime in the industry, a few words regarding the pulp products made in Canada are desirable. By far the largest tonnage is made by grinding spruce and balsam logs on rotating sandstones or on artificial abrasive stones of the Norton or Carborundum types. This mechanical or groundwood pulp finds its largest use in the production of newsprint paper, of which it comprises about 80 per cent of the total fibrous substance employed-the remaining 20 per cent being unbleached sulphite pulp. No limestone or lime is directly employed in making groundwood pulp, as contrasted with the chemically prepared pulps, all of which require one or the other form of the base for their processing. Sulphite pulps comprise the next largest tonnage group. They are produced by boiling, under pressure and at elevated temperatures, spruce and balsam wood in chip form in solutions of bisulphites and sulphurous acid. The usual bisulphites employed are those of calcium and magnesium. Sodium, potassium, and ammonium bisulphites give progressively better pulps, but to date, in the absence of efficient recovery methods, cost has precluded their use.

Jan 1, 1939

In this paper, geostatistical techniques are applied to forecast the annual copper price in the short and medium terms (from one to five years ahead). These techniques allow the incorporation of monthly and multivariate information in the analysis and provide more accurate results than traditional approaches, especially as far as the one-year forecast is concerned. A second advantage of geostatistics stems from its ability to assess the uncertainty associated with the unknown future prices, thanks to estimation variances or confidence intervals, depending on the technique used. Such an assessment has a crucial importance in decision-making, from both macroeconomic and microeconomic points of view

Sep 1, 2004

By J. M. Toye

The Canadian nuclear fuel business relates primarily to supplying fuel for Candu reactors. The product development, manufacturing and marketing activities of our nuclear fuel industry will therefore be determined by the rate of growth of the Candu nuclear reactor business. The nature of this relationship between the Canadian nuclear fuel industry and the Canadian Heavy Water Reactor program will be considered, with particular reference to the factors influencing future economic growth.

Jan 1, 1969

By Walter F. Atkins

Fair market value, in the legal sense , is the price which a prudent and knowledgeable buyer and a prudent and knowledgeable seller, acting without constraint or compulsion , will agree upon to exchange an asset. In the ordinary commercial or engineering usage, the term may imply simply the market value or a reasonable and equitable price. The engineer evaluator who is called upon to express an opinion about the fair market value of an asset may be able to base his estimate on the sale price of similar assets or on the market values of stock. Frequently such indicators of value are not available and the evaluator must devise other means of appraisal. Mineral resource properties may be thought of as having value by virtue of the existing or potential ability to produce at a profit. Conventional procedures permit the computation of the present value of future revenues having due regard for the time value of money and the risks attendant upon the realization of the venture. Such computations have gained wide acceptance as a basis for the estimation of fair market value.

Jan 1, 1977

By Louis Frost

MINE ventilation has for many years been the subject of intensive study by numerous investigators who have presented their findings in forms that are understandable to the average mining man, and all this writer hopes to do is to review those findings in relation to the 'manager's' problem in mine ventilation. It would not, perhaps, be wholly correct to acclaim practical mine ventilation as an exact science, because of the many variables entering into the problem. Each mine has its own particular problem and ventilation characteristics. Fan design, in contra distinction to mine ventilation, is an exact science, but the designer cannot always take into proper consideration the practical variations to which each mine is subject. Fan designers, accordingly, are forced to base their design on such data as the mine manager or engineer is able to supply, and, when it is borne in mind that the mine characteristic is constantly changing, it is not at all surprising that fans do not always show efficiencies hoped for. In many instances, fans work far beyond the de-signer's limitations, and, in consequence, are an economic disability in the colliery cost-sheet, and it is of paramount importance that the colliery manager evaluate all the factors involved in relation to fan performance for the colliery to receive full benefit from its investment.

Jan 1, 1941

By A. H. Lang

THE recent production of important quantities of high-grade muscovite at the Purdy mine, near Eau Claire, Ontario, bas brought that district into prominence and bas added another strategic mineral to the list of Canadian products. The discoveries are thirteen miles west of Mattawa and about two miles north of the Trans-Canada highway and the Canadian Pacific railway. HISTORY Clear mica of low power factor is in considerable demand in Canada and in the United States for war purposes such as radio and telephone condensers, aircraft spark-plugs, radio tubes, and transformers. Some muscovite (white mica) bas been produced in North Carolina and New Hampshire, but the United States trade bas depended largely on importations of muscovite from India and of phlogopite (amber mica) from Madagascar. For many years Canada bas been a substantial producer of phlogopite, but was unable to compete extensively in the United States with importations from abroad. Canadian production of muscovite bas been negligible as no important deposits were known. Ever since the construction of the Canadian Pacific railway, attempts have been made from time to time to mine the pegmatite dykes in and near the Eau Claire area, but, although some feldspar has been mined, no appreciable muscovite was produced. Lace in 1941, J. Purdy and H. MacDonald discovered a dyke containing large crystals of high-grade muscovite from which they are reported to have sold $700 worth of mica. They recorded claims 35974 and 35975 in December, 1941, and claim 36095 in May, 1942.

Jan 1, 1943

By René G. del Villar, Jules Thibault, René del Villar

"Some key control variables of industrial processes, associated with product quality, often cannot be measured directly or frequently enough to establish adequate control. In such cases, it is possible to use available measurements to provide a prediction for these process variables and use them in a control strategy, thereby giving rise to what is now commonly called a softsensor.In some industrial grinding circuits, the on-line particle size analyzer is shared between various sampling points. Therefore, for a given location, the actual measurement is only available every 10 to 20 minutes, a delay which is unacceptable for automatic control purposes. To alleviate this problem, a softsensor based on an artificial neural network has been investigated. First, the structure of the neural network and different schemes for the training process are analyzed. Then, the performance of the neural network softsensor is compared with other inferential methods such as ARMA models and Kalman filters.IntroductionGRAHM, French acronym of the Research Group on Computer Applications in the Mineral Industry at Laval University, began in 1990 a research project on Knowledge Based Automatic Control (KBAC). This project, sponsored by a consortium of eight mining companies and the federal and provincial governments, seeked to screen advanced (knowledge-based) methods for data processing (filtering, mass balancing, etc) and automatic control (model-based) for their use in the mineral processing operations and the transfer of the project results to the sponsor companies.In parallel to more academic research work, a number of case-studies have been undertaken with the cooperation of partner companies. Among such works, a very successful one has been the design and installation of a new control strategy for one of the Kidd Creek (Falconbridge Ltd.) grinding circuits. This project was related to the evaluation of a number of control strategies and the implementation of one of them, as selected by the plant management, in the concentrator.A total of sixteen control schemes were evaluated on one of the dynamic phenomenological simulators developed at GRAHM, a trademark of this research group [ l]. The calibration of the simulator models was done based on industrial data gathered by GRAHM and Kidd Creek personnel. Then, the simulator was used to test the performance of various PID-based control schemes, designed to achieve the control objectives set by the Kidd Creek personnel. The best scheme proposed called for controlling the cyclone overflow particle size by manipulating the water addition rate to the cyclone feed box and the circulating load by manipulating the circuit ore feed. The particle size analyzer (PSI-200) available for monitoring the product size, was unfortunately shared (multiplexed) among various streams of the plant, which meant a 14 min delay between two consecutive readings for any particular stream. This induced the plant personnel to choose an alternative control strategy, one which controlled the cyclone feed density instead of the cyclone overflow particle size."

Jan 1, 1996

By H. A. Kee

In the mining industry, as in other business, one of the more satisfactory results of sincere but cheerful effort lies in the proper completion of undertakings and problems, which, to be successful, must continually hold the interest of all concerned in the work. In most undertakings, genuine interest and satisfaction is largely dependent on the proper appraisal of opportunities presented, and the opportunity to associate ourselves with sinking operations at McIntyre central shaft, from the surface to a depth of 4,133 feet, was genuinely appreciated. This opportunity was made possible by the previous persistent and successful leadership of Mr. J. P. Bickell, President, with the assistance of his associates, and of the general manager, Mr. R.J. Ennis, in the development of the McIntyre Porcupine mine, and I beg to state that any success in this sinking operation was very largely due to the congenial co-operation and splendid workmanship of Captain Martin C. Horne, his shift bosses, leaders, and all those who worked with us . Our slogan throughout was " Safety First for Pleasant and Efficient Workmanship," and this general policy made it possible to sink and timber 2.,123 feet during the first year without a serious accident.

Jan 1, 1928

By H. A. Wentworth

The Central Manitoba mining district, as spoken of in Manitoba, refers to that portion of the country lying between lake Winnipeg on the west and the Ontario boundary on the east, and from a few miles north of the Wanipigow (or Hole) river on the north, to a few miles south of the Bird river. It embraces two known mineralized belts; the gold area in the north, extending from the shores of lake Winnipeg almost to the Ontario boundary (in a slightly southeasterly direction) a zone some eight or ten miles wide and perhaps forty miles long, lying (for the most part) north, and parallel to, the Manigotagan river; and the Bird river copper and coppernickel deposits, an area not yet clearly defined, but in general lying immediately north of, and roughly parallel to, the Bird river. To the south of the Bird river is a somewhat differently mineralized area, numerous pegmatite dykes being found, with minerals typically associated with such rocks. More specifically, the known gold deposits are largely segregated in the above belt; (1) around English brook; (2) along the north shore of Wanipigow lake; the Rice lake area (about midway of the belt); and the Long Lake-Bulldog lake area, at the eastern end of the belt. Not all the known gold occurences are found in these segregations, but the density of claim staking in these areas is perhaps an indication of the greater number of prospects found in them to date.

Jan 1, 1925