Search Documents

By K. Matsuura, M. Ohno, T. Tokunaga

"Recently, weight saving of automobiles has been strongly required to solve the global environmental problems. Mg alloys are one of the promising candidates as a new material for automobile components. However, the application of the Mg alloys is limited due to their poor corrosion resistance. In the authors’ preliminary study, an Al/Mg/Al clad sheet was fabricated by hot extrusion and subsequent hot forging. The clad sheet exhibited a high corrosion resistance and excellent super plasticity. More specifically, the elongation of the clad sheet was as high as 550%.Importantly, despite that the elongation of Al itself was only 40%without cladding with Mg, the ductility of Al was greatly improved in the form of the clad sheet. In the present study, in order to clarify the mechanism of the superplastic deformation of the Al part in the clad sheet, the microstructure evolution of the Al during the tensile de formation is investigated. The tensile tests were conducted at a temperature of 573 K and at a strain rateof1.0×10-3s-1. The Al exhibited fiber-type texture at the beginning of the tensile deformation, and brass-type texture after the elongation of 50%.INTRODUCTIONMg alloys have been gaining attention because of their excellent properties e.g. light weight, good recyclability and high electromagnetic shielding. However, their practical applications have been limited due to their poor corrosion resistance. In the authors’ previous study, in order to solve this problem, Al coating on Mg alloy by hot extrusion has been proposed, and the Al-coated Mg alloy plate was fabricated(Tokunaga, Matsuura, &Ohno,2012). The plate was hot-rolled and an Al/Mg/Al clad sheet was fabricated. No cracks or debondings were observed at the Al/Mg interface. The sheet exhibited a high corrosion resistance in a comparable level as pure Al. Also, the sheet exhibited a large and uniform elongation of 550%in a tensile test at a temperature of 573 K and at a strain rate of 1.0×10-3s-1without any breakings or debondings of the Al part(Tokunaga, Matsuura, &Ohno,2014).Mg alloys have been known to exhibit a superplastic characteristic when the grain size is small. However, it is known that the pure Al does not generally exhibit the super plasticity. As mentioned above, the Al-coated Mg alloy sheet exhibited 550% of elongation in the authors’ previous study (Tokunagaet al., 2014). However, the pure Al itself showed only 40% of elongation, while the Mg alloy itself exhibited 800% of elongation. Thus, it has been demonstrated that the pure Al was super plastically elongated when it was bonded with the Mg alloy. Generally, deformation mechanism of the super plasticity of the Mg alloy is known as a grain boundary sliding. On the other hand, the mechanism of the superplastic elongation of the pure Al is still unclear. The purpose of the present study is investigation of the deformation behavior of the Al part in the Al/Mg/Al clad sheet during tensile de formation."

Jan 1, 2018

By A. Singh

"Flotation of fine (< 10 µm) minerals is a challenge exacerbated by the emerging practice of fine grinding flotation feed to better liberate targeted minerals; however, the ability of conventional flotation cells to float liberated fines remains questionable. The Gold Ore solution using Mach reactors was tested at Mintek, South Africa, and showed an ~180% increase in the Kelsall kfast factor, a projected recovery improvement of 4% for the Mach-reactor case, and final concentrate grade twice that of conventional flotation. Theory, pilot plant results, and key aspects of plant design, supplemented by operational plant observations after commissioning, are discussed.RÉSUMÉ Le procédé de flottation de minerais fins (< 10 µm) pose de grandes difficultés, lesquelles sont aggravées par la pratique émergente de l’alimentation du circuit de flottation avec des mailles de broyage très fines pour mieux libérer les minéraux ciblés ; la capacité des cellules de flottation classiques à flotter les fines de minerais libérées reste cependant discutable. La solution proposée par la société Gold Ore, qui utilise des réacteurs Mach, a été testée à Mintek, en Afrique du Sud ; elle affichait une augmentation d’environ 180 % du facteur kfast développé par M. Kelsall dans son modèle de flottation, une amélioration prévue de la récupération de 4 % dans le cas du réacteur Mach, et une teneur finale des concentrés deux fois plus importante que celle obtenue avec la flottation classique. Sont débattus dans cet article la théorie, les résultats générés par l’usine pilote ainsi que les principaux aspects de la conception de l’usine complétés par des observations relatives à l’usine en activité après sa mise en service."

Jan 1, 2018

By Takanori Kokubo, Kenta Suzuki, Tomohiro Sasaki, Toshiya Anami

"Previous work has shown that the strengthening Al-Mn alloys with copper leads to the formation of an undesirable reduction in recrystallized grain size. In this study the mechanisms of strengthening and recrystallization behavior in a continuously cast automotive heat exchanger fin stockof Al-1.1wt%Mn-0.5wt%Fe-0.3wt%Si with a0.3wt%Cu addition were investigated. Metallurgical analysis revealed that the Cu strengthening was dominated by the formation of dispersoid particles, while solid solution strengthening decreased with the Cu additions. This result is attributed to the decrease in the amount of Mn solid solution. The post brazing recrystallized grain size was reduced compared to that not containing Cu. It is postulated that the Cu addition leads to a decrease in the amount of Mn in solid solution which leads to a finer grain size. This effect is attributed to Mn in the aluminum matrix inhibiting boundary migration but allowing other grains to grow during heat treatment. The results are rationalized based on particle stimulated nucleation (PSN), wherein dispersoid particles are more likely to become active recrystallization nuclei during the heat treatment. The increase in the number of active dispersoid particles with Cu addition is correlated to the recrystallized grain structure.INTRODUCTIONImprovements in properties such as strength, braze ability and corrosion resistance in thermal fin stock alloys are all means to gain improved efficiency in heat exchangers particularly in automotive applications. While Al-Mn alloys dominate automotive heat exchanger fin stock alloy, even small chemical compositional changes can profoundly influence these properties (Kawaharaet al., 2004; Yoshino et al., 2009). The microstructure (particularly the grain size and shape) also plays a key role in determining the product performance and hence the thermo-mechanical processing (TMP) must also be considered. The casting method (typically conventional direct chill, DC, or continuous casting) significantly influences the properties in no small part due to the very different TMP routes that are used. Continuous casting is generally favored for fin stock applications as its higher cooling rate (which can be 2 to 3 orders of magnitude higher than DC casting) leads to finer as-solidified intermetallic particles and an increase in super-saturated solid solution elements (such as Mn)that are known to improve fin stock performance such as strength, braze ability(Okiet al., 2008)."

Jan 1, 2018

By Joseph Licavoli, Paul Sanders, Yang Yang

"Al-Sc-Zr alloys form thermally stable L12 precipitates which provide high temperature strength. Although the overall fraction of L12 Al3Sc and Al3Zr may be increased by increasing scandium (Sc) and zirconium (Zr) content, such additions may increase primary phase fractions and do not produce desirable secondary phase morphologies. Rapid solidification techniques, such as melt spinning, increase solute atom concentration within the matrix. When the supersaturated matrix is aged, higher precipitate volume fractions at low Sc and Zr levels can be achieved improving high temperature strength. Melt spinning was used to rapidly solidify (107 k/s) a thin ribbon of Al-0.5Sc-0.4Zr at. %. The ribbon was compacted and extruded into 99.8% dense rods, and then aged using multi-step isochronal heat treatment up to 600°C. Precipitation strengthening was evaluated by ambient hardness measurement. The ambient hardness of melt-spun ribbon after precipitation hardening increased by 450 MPa (~67% increment) during isochronal heat treatment.INTRODUCTION Small Sc and Zr additions to aluminum improve strength and creep resistance above 300°C due to tri-aluminide precipitation of Al3(Sc,Zr) in L12 structures similar to ??, Ni3(Al,Ti) in nickel superalloy, but the Al3(Sc,Zr) particles have a Sc-rich core surrounded by Zr-rich shell (Figure 1). The Al3Zr shell limits atomic transport between the Al3Sc core and the matrix and reduces coherency strain. These factors reduce precipitate coarsening rate at elevated temperature (Bergner & Van Chi, 1977; Fujikawa, 1997; Knipling et al., 2011; Clouet et al., 2006).Figure 1. Simplified schematic model of precipitate Al(Sc,Zr) in Al-Sc-Zr alloy. Shell is rich of Al(Zr) intermetallic phase, particle core is rich of Al(Sc) intermetallic phase (after Voorhees, 2006). Numerous Al3(Sc,Zr) particles increase alloy strength and creep resistance as the precipitates impede dislocation glide and to a lesser extent climb. Previous work on ternary Al-Sc-Zr alloys show large strength increases versus binary Al-Sc, and Al-Zr alloys in Table 1."

Jan 1, 2018

By Ifeanyichukwu Nweke

"Aluminium rolling processing from ingots to cold rolled coils comes with a lot of challenges especially in controlling defective products in casting, hot mill and cold mill operations. Hence this study focused on reducing defects at mills and cast-house using six sigma approaches. The use of six sigma approach will help the production experts to determine the gap between its operation and world class process. Practical data from First Aluminium Rolling mills were presented and analysed and mini improvement projects were proposed based on organisation need to achieve excellence. This study encourages aluminium alloy industries to pursue process improvement projects on the basis of analysis on data obtained from their shop floor, hence ensuring that through this, recovery is improved and cost of poor quality is reduced.INTRODUCTION Engineer Bill Smith while working at Motorola in 1986 introduced a new concept in which a set of techniques and tools are used for process improvement by controlling variations (defects). These tools and techniques are explained by an acronym DMAIC. D DEFINE the problem M MEASURE the variables in the problem A ANALYSE the variables of the problem I IMPLEMENT and verify the solution to the problem C CONTROL the solution to sustain it Most times in six-sigma approach, variations in the process that results in defects and customers’ dissatisfaction are targeted at 3.4 defects per million opportunities. There are numerous methods six sigma application use to achieve quality results and innovative strategies. Improving the quality of process through these methods helps identify and reduce variations which paves way for organisational excellence. In this study, it is encouraged to use six sigma techniques to improve aluminium rolling operations and other aluminium processing activities, the benefits of such improvement concept include: • Satisfy the voice of the customer (VOC) • Minimise costs • Maximise Profits • Build Good Team • Implement Profitable Project"

Jan 1, 2018

By P. Homola, M. Karlík, M. Slámová

"Aluminum sheets (AA1199, AA8006, and AA5754) were processed by accumulative roll-bonding (ARB) in the temperature range from 20 to 350°C. The microstructure of the sheets was characterized by means of scanning and transmission electron microscopy and electron backscattered diffraction. Mechanical properties were monitored by hardness measurements and tensile tests. Increasing strain (number of ARB cycles) led to incremental development of lamellar microstructure with a decrease of the spacing between high-angle grain boundaries in the normal direction of sheets. ARB process produced an important increase of strength while maintaining thickness and relatively high ductility, without accenting of the anisotropy of mechanical properties of sheets. The level of hardening decreased with the processing temperature and at 300 and 350°C ARB caused even the softening of the material due to the recovery of the deformed microstructure or partial recrystallization during heating to ARB processing temperature.INTRODUCTION Accumulative Roll Bonding (ARB) is a technique of grain refinement by severe plastic deformation (SPD) proposed by Saito et al. (1999). One ARB cycle consists in sheet cutting, surface treatment, stacking of two pieces, heating (optional), and rolling with 50% reduction in thickness. Since the sheet thickness remains unchanged by this cycle, ARB processing can be repeated as many times as desired. The goal of ARB is to impose an extremely high plastic strain on the material, resulting in structural refinement and strength increase without changing specimen dimensions. After several cycles, ultra-fine grained (UFG) materials with high strength and relatively high ductility are produced. An advantage of this method is that it does not require any special equipment as other SPD methods such as equal channel angular pressing (ECAP) (Valiev & Langdon, 2006), high pressure torsion (HPT) (Valiev et al., 2000), or cyclic extrusion and compression (CEC) (Richert et al., 1999), but only a conventional rolling mill and so it is seen as an economically viable and industrially scalable processing route. ARB processing has been successfully applied to various kinds of metallic materials at room or elevated temperatures (Tsuji, 2005). Besides processing single metals and alloys, ARB has also been used for creating ultra-fine grained and nanograined metallic composites (Wu et al., 2010; Qu et al., 2014)."

Jan 1, 2018

By Y. Tang

"Rare earth elements (REEs) have many key applications in traditional and advanced technologies. A shortage of several critical REEs is expected due to the discrepancy between the availability of REEs from REE deposits and the REE demand from the market. REE recovery and separation from secondary resources such as uranium wastes and recycled materials might help balance the shortfall in a cost-effective way. This paper presents data concerning the recovery of heavy REEs (HREEs) from uranium raffinate. It also discusses the design, commissioning, and operation of a solvent extraction pilot plant for the separation of REEs.RÉSUMÉ Les éléments des terres rares (ÉTR) trouvent de nombreuses applications importantes dans les technologies classiques et de pointe. On prévoit une pénurie de plusieurs ÉTR critiques en raison des divergences constatées entre la disponibilité des ÉTR provenant de gisement d’éléments des terres rares, et la demande d’ÉTR sur le marché. La récupération et la séparation des ÉTR à partir de ressources secondaires telles que les déchets générés par le traitement du minerai d’uranium et les matériaux recyclés pourraient contribuer à équilibrer cette pénurie de manière rentable. Cet article présente des données relatives à la récupération des ÉTR lourds (HREE, de l’anglais heavy REEs) à partir de raffinat d’uranium. Il aborde également la question de la conception, de la mise en service et de l’exploitation d’une usine pilote d’extraction par solvants pour la séparation des ÉTR INTRODUCTIONSignificant amounts of strategic specialty heavy rare earth elements (HREEs) are present in waste streams in Saskatchewan uranium operations. Selective precipitation including neutralization, oxalate, and double-salt precipitation, as well as sulfide precipitation, ion exchange (IX), and solvent extraction (SX) are commonly used technologies for the recovery and purification of rare earth element (REE) solutions. REE oxalate precipitation can effectively remove Fe, Al, Ca, Si, and other impurities by taking advantage of the solubility difference between REE oxalates and impurities in the acidic solution (Xu, 2005)."

Jan 1, 2018

By R. Darlington, S. Ji

"High pressure die casting is a promising process to make thin-wall components with high dimensional accuracy and excellent surface quality. However, the non-uniformity is one of the important features in castings. The inhomogeneity in tensile properties and microstructural characteristics were studied for the castings with different thicknesses made by high pressure die-cast Al-Mg-Si alloys. For the local mechanical properties in the die-castings, the casting skin provided the highest, whereas the casting centre provided the lowest yield strength, UTS and elongation. The yield strength, UTS and elongation were significantly decreased towards the casting centre. The microstructural inhomogeneity is characterised by the segregation of coarse fragmented dendrites, the reduction of solute concentrations of Mg and Si, and the increase of porosity level from the surface to the centre of castings. The growth velocities of eutectic a-Al phase estimated using the Jackson-Hunt model confirm that the growth variation is larger in the thin castings than that in thick castings.INTRODUCTION Inhomogeneity is an inherent characteristic in as-cast microstructures of a variety of alloys because of their non-uniform chemistry, microstructure, defects, topology and the resultant mechanical properties in the different ranges of localization (Campbell, 2003). Generally, three types of inhomogeneities characterise casting microstructures, which include (a) the casting defects of shrinkage and gas porosity, misruns, cold shuts, inclusions, hot tears and hot spots; (b) the non-uniform microstructure from the surface to the centre of castings; and (c) the non-uniform microstructure from the dendrites grown from primary solidification and the structure formed during the subsequent eutectic solidification in inter-dendritic regions. The chemical composition and the morphology between the primary dendrites and the inter-dendritic eutectics also differ in the as-cast microstructure. Obviously, the inhomogeneity is different in the castings obtained from different casting processes."

Jan 1, 2018

By M. Samuels

"Block and panel cave mining methods are being increasingly proposed as they allow massive, deeply situated ore-bodies to be mined economically at a time when discovery rates of significant near surface deposits are declining. Cave-to-Mill, a mine-to-mill approach for block cave mines, defines ore block models with respect to both mine and mill performance. A cave-to-mill study for the New Afton block caving operation focused on identifying value opportunities related to fragmentation and sorting for a future lift as development progresses deeper. The lack of selectivity and potential for dilution associated with the block cave mining method results in many caving operations having to mine and either dispose of or process material that is below cut-off grade at certain stages of production. As an outcome of the study, the variation in cave fragmentation size and the sensitivity of mill throughput to feed size was examined. To evaluate the amenability of bulk and particle sorting, Prompt Gamma Neutron Activation Analysis and X-Ray Fluorescence sensors were tested. A conceptual bulk and particle sorting flowsheet is presented. Grade data from regular underground sampling was used to predict the performance of a bulk sorter. A heterogeneity analysis of material reporting to drawpoints helped to identify areas of the extraction level that experience high variations in grade and thereby stand to benefit from dedicated ore and waste material handling systems should underground bulk sorting be implemented.INTRODUCTION Block and panel caving are low-cost underground mass mining methods that are suitable for excavating weak, massive and steeply-dipping orebodies. Accordingly, cave mining methods have predominantly been used to mine copper porphyry and diamond bearing deposits. Due to the increasing depletion of near-surface orebodies, it is expected that block and panel caving methods will be increasingly used in the copper-gold industry. Their implementation holds significant potential to extend the life of existing open-pit operations by providing an economic means to access ore located at depths that are beyond the practical limits of open-pit mining. Examples of cave mines proposed for British Columbia include the Kwanika Mine, Red Chris underground, Kemess Underground project, and the Iron Cap and Mitchell cave mines of the Kerr-Sulphurets and Mitchell (KSM) project (Moose Mountain Technical Services, 2017; Imperial Metals, 2017; Golder Associates, 2017; Tetra Tech, 2016)."

Jan 1, 2018

By A. Rousselet, H. Gilbert-Tremblay, A. Berton

"Robex Resources interrupted production at the Nampala Mine in September 2014 following throughput and gold recovery results which were below expectations during the first months of operation. After a thorough plant audit, an important brainstorming took place in order to identify an economical path to resume production. It was clearly identified that a significant investment was necessary at the concentrator prior to restarting the plant, namely the addition of a ball mill and a new elution system.The mineral processing simulation software USIM PAC was used in order to simulate the grinding circuit in design. The simulations’ outputs allowed the ball mill characteristics and the surrounding classification devices to be designed with more accuracy. Many ball mills available from second hand retailers were therefore studied in the simulated circuit. The chosen ball mill, which was in perfect condition, had the advantage of being available for rapid delivery on site.The paper first describes the ball mill sizing method in comparison with the conventional Allis Chalmers method. It then describes the phase 2 concentrator start-up (that took place in 2016) with the commissioning of the ball mill, the classification circuit, the gravity concentration, the four (4) new carbon-in-leach (CIL) tanks, and the Zadra elution system (The phase 1 start-up took place in 2014). It finally provides production data compared to expected simulation data, as commercial production was reached in January 2017.IntroductionDesigning a new concentrator or new equipment within an existing concentrator requires significant efforts to identify possible bottlenecks and their causes (i.e. limiting equipment or sectors) and accurate sizing of major equipment can have a tremendous impact on the economy of the whole project. In the presented case study, the ball mill was the critical equipment and oversizing it could have brought the Capex to a level where the project would not have gone through. Inversely, undersizing the mill could have resulted in lower production and therefore no economic viability for the project once it is in operation.During engineering studies, equipment sizing often relies on a static mass balance and one-by-one sizing of all pieces of equipment. The sizing is then left to the equipment manufacturer or in the case of mills, evaluated with empirical models mostly relying on the Bond equations (Allis Chalmers method) [Rowland and Kjos, 1978]. This methodology shows the disadvantage of not considering interaction between equipment in a mineral processing circuit, especially when recirculation occurs. Also, it has the disadvantage of not using the more advanced grinding models that include the use of the whole particle size distribution as well as phenomenological components by only using limited parameters in the ore particle size distribution (i.e. the P80). This can be explained by the lack of data that sometimes needs to be gathered in order to tune the more advanced models but also by the conservative mindset in mineral concentration engineering which does not always favor the use of process simulation. In many aspects of process engineering, Soutex has demonstrated its affinity to using simulation in order to size equipment with more accuracy, consider process variability, simulate complex systems, and study supply chain management (Berton et al., 2015)."

Jan 1, 2018

By D. Purdie

"This paper aims to remind researchers, designers, operators, and managers about the benefits of seeding in the design of precipitation stages in their flowsheet. Including a high density solids (HDS™) process encourages the precipitating solids to form on the surface of existing precipitated particles. This paper discusses the application of the HDS technology at Kennecott Smelter, where the authors have witnessed significant improvements in settling and filtration rates. The authors have also applied this technology at various smelter bleed treatment plants worldwide with similar improvements in precipitation and filtration rates. HDS is a registered trademark of De Nora Water Technologies. RÉSUMÉ Cet article a pour objectif de rappeler aux chercheurs, aux concepteurs, aux exploitants et aux administrateurs les avantages de l’ensemencement dans la conception des étapes de précipitation de leur schéma de traitement. L’introduction d’un procédé des boues haute densité (procédé HDS™, de l’anglais high density sludge) encourage la formation de substances solides précipitantes à la surface des particules précipitées existantes. Cet article porte sur l’application de la technologie HDS à la fonderie Kennecott, où les auteurs ont observé des améliorations importantes au niveau de la vitesse de sédimentation et de filtration. Ils ont également appliqué cette technologie à diverses usines de traitement des rejets liquides des fonderies dans le monde entier, et ont constaté des améliorations similaires en termes de vitesse de précipitation et de filtration. Le procédé HDS est une marque de commerce déposée du fabricant De Nora Water Technologies.INTRODUCTION In 1966, the lead author worked as an assistant smelting metallurgist for the Tsumeb Corporation Limited copper and lead smelter in Tsumeb, Namibia. The smelter produced copper and lead, as well as cadmium and arsenic trioxide as byproducts. The cadmium was concentrated in the lead blast furnace off gas dust, and was collected by a baghouse. The baghouse dust was leached with dilute sulfuric acid (H2SO4) in a batch process. The iron and arsenic in the solution were oxidized with potassium permanganate (KMnO4) and basic ferric arsenate (BFAS; Fe(AsO4)x(SO4)y(OH)z·wH2O) was precipitated using milk of lime. The cadmium was cemented from the purified solution using zinc dust."

Jan 1, 2018

By S. J. Prout, J. M. Lang, D. Lascelles, K. Sarinas

"There is a growing demand for ore characterization methods to support metallurgical development programs from a true geometallurgical perspective. Today, there are multiple automated mineral analysis systems on the market, many of which are based on conventional mineral liberation data. However, liberation data can be limited when assessing the floatability of a mineral to predict its recovery as it doesn’t consider the surface area available for collector absorption and bubble attachment; whereas mineral exposure measurements can. Using the First-Order Rate equation to predict the recovery versus time of variously exposed particles, a model has been developed to predict the recovery of copper sulphides at a particular grind size. This model provides the opportunity for the prediction of copper recovery and grade from multiple, small-scale samples. These predicted values can be imported into resource modeling software, and guide the domaining of geometallurgical units within the ore body. Data has been analyzed from various global copper porphyry systems and compared with actual flotation testwork.IntroductionAs part of the development of a mining project, resource estimation primarily focuses on the definition of the quantity and grade of the ore in the deposit; as the project evolves from preliminary economic assessment through to feasibility, the geological model is usually further populated with hardness and recovery data.The CIM Definition Standards (2011) identifies measured mineral resource as the part of a mineral resource for which quantity, grade or quality, densities, shape, and physical characteristics are estimated with confidence sufficient to allow the application of “modifying factors” to support detailed mine planning and final evaluation of the economic viability of the deposit as an asset. The modifying factors include, but are not restricted to, mining, processing, metallurgical, infrastructure, economic, marketing, legal, environmental, social and governmental factors.With market fluctuations, many investors in the mining industry have become more and more risk averse which has increased the demand for more reliable data to support these modifying factors. This has led to the widespread use of geometallurgy and statistical analysis to better inform the resource estimation. Geometallurgy is used to characterize ore variability and is especially useful for highly variable or strongly zoned deposits, several close deposits that will be milled together, projects requiring complex or new metallurgical approaches, brownfields or sight-of-mine exploration, expansion projects that exploit new, deeper or adjacent reserves, and projects with significant legacy drill core that are being re-evaluated due to new economic circumstances."

Jan 1, 2018

By M. K. Jain, Z. T. Xu, M. Bruhis, V. Hegedekatte

"Strain rate and temperature dependent deformation conditions are present during elevated temperature forming of aluminum and other metallic materials. While many constitutive laws have been proposed to represent such deformation conditions, a closer investigation often reveals their limited applicability in terms of fit to the experimental data, and interpolation within and extrapolation outside of the range of experimental stress-strain curves. This is often because material-specific primary deformation mechanisms of temperature-dependent strain and strain rate hardening are poorly captured. In the present work, the Voce-Kocks constitutive model based on mechanics of dislocations storage and annihilation has been found to be suitable for many metallic materials. The model was modified to include the effect of temperature dependent shear modulus. The modified model is then employed to represent the experimental data obtained from uniaxial tensile tests on AA7075-O sheet at elevated temperatures and strain rates. Also, hot gas bulging tests were conducted to verify the applicability of this model. Further, finite element simulation of the hot gas bulge test was performed by incorporating the model as a user material subroutine. Good general agreement was observed between the experimental and FE model predicted results. Some sources of discrepancy in the prediction are also discussed.INTRODUCTION There has been much interest in light-weighting of automobiles from automotive related industries to reduce overall carbon footprint and increase energy efficiency of the vehicles. Aluminum alloys, and especially the medium-strength 5xxx and 6xxx series alloys, have been the primary focus in the last 3 decades to reach the above environmental goals (Huo, Hou, Zhang, & Zhang, 2016) whereas aerospace industry has traditionally focused on high strength 7xxx series aluminum (Al-Zn-Mg-Cu) alloys for structural components (Deng, Yin, & Huang, 2011). Recently, there has been much interest in high strength 7xxx series aluminum as a replacement for heavier steel automotive structural parts such as A-pillar, B-pillar, side impact beams etc. (Harrison & Luckey, 2014). This is both interesting and challenging since the above aluminum structural parts will need to not only meet impact safety standards but also possess sufficient formability for manufacturing such complex parts. Since the formability of high strength 7xxx series materials is quite poor at room temperature, much interest has focused on improving both formability and final part strength via high rate hot stamping, in-die quenching, and subsequent artificial ageing process steps (Kumar & Ross, 2016)."

Jan 1, 2018

By Kenta Suzuki, Toshiya Anami, Daisuke Shimosaka

"In an Al-Mn alloy heat exchanger fin stock, the effect of annealing conditions for as-cast and 0.1%Zr addition on recrystallization behavior is investigated using metallurgical analysis. Refinement of post-brazed recrystallized grains in fin stocks with Zr addition are suppressed for long-time annealing. In 0.1%Zr fin stocks, there was a decrease in the number of fine a-Al(Mn,Fe)Si dispersoids for pinning of sub grain and grain boundary. In addition, relatively homogeneous distribution of Al3Zr dispersoids was observed with increasing annealing time in as-cast. Homogeneous distribution of Al3Zr dispersoids can have a major effect on pinning of sub grain and grain boundary during brazing heat treatment. The homogenous distribution of fine dispersoids prior to brazing heat treatment is effective in causing the suppression of refinement of post-brazed recrystallized grain structure in aluminum alloy fin stocks.INTRODUCTIONAl-Mn based alloys are widely used as fin stocks in automotive heat exchangers because of their superior mechanical properties, braze ability, sagging and so on. In particular, coarsening of recrystallized grain structure is beneficial to avoid erosion, and achieve excellent sagging resistance (Lee, Yoon, Kim & Jung, 2002). For resisting grain coarsening, the alloys should contain a dense and homogeneous distribution of fine dispersoids to retarder crystallization (Humphyreys& Hatherly, 2004). It has been demonstrated that addition of Zr to Al-Mn alloys can shift recrystallization to higher temperatures because of the distribution of fine Al3Zr dispersoids in matrix(Pokoba, Cieslar& Lacaze,2012). According to Tohma, Asanoand Takeuchi (1987), coarsely recrystallized grain structure was obtained in 3003alloy with Zr addition after heat treatment. However, fine Al3Zr dispersoids are usually heterogeneously distributed because of segregation during casting and low diffusion rate of Zr in aluminum. Therefore, a homogeneous distribution of Al3Zr dispersoids can be achieved through long-time precipitation annealing(Jia, Hu, Forbord& Solberg, 2008)."

Jan 1, 2018

By J. Kronsteiner, E. Kabliman

"In the present work, we developed a Smart Process Control Toolkit (SProC) as a single simulation environment for the modelling of materials microstructure and its interaction with the local microchemistry during manufacturing of semi-finished products. This toolkit supports the data communication between sub-sequent processing steps such as casting, homogenization, pre-heating to deformation, etc. The thermo-kinetical simulation software MatCalc of MatCalc Engineering© GmbH was used for modelling of precipitation kinetics, such as formation of primary and secondary phases and their evolution. An import/export functionality of the precipitation distribution after each processing step was implemented to follow the parameter history. For the evolution of the local microstructure, a Mean Dislocation Density based Model (MD2M) was used. This model consists of two parts: (1) Flow Stress Model for calculation of the total strength during the deformation and (2) Static Recrystallization Model for account of the recrystallization and grain growth after the deformation. Validation was done by a comparison of experimental and simulated hot compression tests of a conventional AA2024 alloy.INTRODUCTION Optimization of a semi-finished products quality, elimination of typical production issues and cost savings are of a great demand for supply industries. However, it is currently not feasible to investigate the whole manufacturing process in detail at an industrial level. Concerning the processing parameters, one must understand the correlation mechanisms between macroscopic properties and microscopic material behavior. Numerical simulations, which could reproduce the real processing conditions on the one hand, and employ a physically based modelling on the other, are thus attracting a lot of attention and their power is no longer under the question. It is well known that e.g. the total strength of the material depends directly on distribution of precipitation particles and mean grain size. In order to follow their evolution during the manufacturing process beginning from casting to the final semi-finished product, and thus be able to control the process, one should use the techniques which would at the same time reproduce experimental processing conditions of real size objects (e.g. sheet, extrusions, etc.) and account for the evolution of a local microstructure and its interaction with the microchemistry. A commonly used approach is to implement a model which would describe the evolution of microstructure based on a dislocation density approach into a user defined material subroutine of some finite element solver. There is, however, also an influence of the manufacturing process by e.g. the evolution of a local microchemistry (formation, transformation and dissolution of the precipitation particles) on the microstructure and thus the macroscopic material behavior. Thus, a method is needed to follow the variable history through the simulation of the whole production chain."

Jan 1, 2018

By C. J. Simensen, R. Østhus, H. J. Roven, K. G. Skorpen, H. Kalager

"This work encompasses co-extrusion of alloy Al4.5Mg at the core and rapidly solidified Al4.5Mg1Ag forming the surface layer. The goal is to produce a multi-material by co-extrusion having a relatively hard surface as compared to a softer core. At the same time, work hardening in both alloys is expected to be significant due to Mg in solid solution. Precipitation hardening at 160°C is studied by applying solution heat treatments at 560°C. The hardness increased from 80 to 130 VH in the surface material after 236 h. Surprisingly, the Al4.5Mg alloy also shows pronounced aging at this temperature, i.e. from 70 to 90 VH. The relatively high solution heat treatment temperature introduces grain growth in the core, but this is insignificant for the RS surface alloy. Blisters forms at the surface and cracks follows large portions of the interface. However, the tensile ductility is significant in all conditions due to very pronounced work hardening, i.e. for the as co-extruded, T6, under- and over-aged. The elongation at fracture ranges between 40–45% and the tensile strengths 240–275 MPa. The tensile properties increase linearly with the thickness of the RS alloy, i.e. following the rule of mixtures.INTRODUCTION Al-Mg alloys in 5xxx-series are classified as non-heat treatable wrought alloys (Polmear, StJohn, Nie, & Ma, 2017). The formation of the binary ß-Al8Mg5 does not give a substantial increase in the strength of the alloys (Mondolfo, 1976). When a third element like Ag, Cu or Zn are added, G.P.?zones are formed at low temperatures and intermediate, partial coherent phases are nucleated somewhat higher temperatures and finally a ternary, equilibrium phase is formed (Auld, 1968; Cousland & Tate, 1986; Mondolfo, 1976). Both the formation of G.P.?zones and intermediate phases increase the hardness and strength of the materials. An intermediate, hexagonal T´?phase is formed in Al-5 wt%Mg-1wt%Ag, and finally the equilibrium, cubic phase (Al,Ag)9Mg5 is nucleated (Cousland & Tate, 1986; Mondolfo, 1976)."

Jan 1, 2018

By A. Plugatyr, C. P. Baxter

"Bessemer matte iron content is a critical process parameter that needs to be closely monitored and controlled in order to achieve optimal Ni/Cu smelter returns. Current process control practices during Ni/Cu converting often rely on visual observations and typically involve matte sampling to confirm that target composition was reached. A high-level techno-economic analysis study was carried out to evaluate potential direct benefits of advanced process control during the final stages of Ni/Cu matte converting. The results indicate that the magnitude of direct benefits will largely depend on matte iron control practices already implemented as well as matte iron set point. Preliminary assessment suggests that under the assumptions used in this study, implementation of advanced process control can potentially result in additional revenues ranging from several hundreds of thousands to tens of millions of US dollars per year per converter producing about 200 tonnes of Bessemer matte per day based on Ni, Cu, and Co metal recoveries alone.INTRODUCTION Real-time measurement of molten metal elemental composition, arguably, remains one of the key unresolved issues impeding full automation and real-time optimization of pyrometallurgical operations in different industrial areas, including non-ferrous metals and ferro-alloys. In particular, current process control practices during Ni/Cu matte converting often rely on visual observations and typically involve matte sampling in order to confirm target matte composition. In addition to being time consuming, this approach relies heavily on operator experience and diligence, and, therefore, requires continuous performance and quality control efforts. For instance, the need to improve quality of the Bessemer matte (BM) at the Copper Cliff smelter has prompted an impressive staff engagement and training campaign that was carried out by Vale’s team in the late 2000’s (Zanini, Wong, & Cooke, 2012). This training exercise was executed to address the compounded effect of several operational challenges, namely demand for higher throughputs, changes in the feed concentrate composition, increased feed variability, loss of process knowledge and expertise due to retirement, as well as lack of a comprehensive approach to improving the overall performance of the flowsheet rather than meeting production targets for intermediate products. Although the campaign was very successful and has resulted in significant improvements in the Bessemer matte quality, it has also highlighted the need to move away from “the-art-of-converting” and develop analytical tools that would enable real-time process monitoring."

Jan 1, 2018

By G. Morin, F. Chiesa, B. Tougas, B. Duchesne, Jocelyn Baril, N. Giguère

"An aluminum A356 compressor impeller was sand cast using the Low Pressure technique. The casting was limited in size (170 mm in diameter, 1.2 kg in weight) and very intricate in shape thus making 3D mold printing particularly favorable; indeed, producing this part by the traditional pattern-core box route would involve mounting 12 cores inside the mold while stringent dimensional tolerances are required as the impeller blades are only 2 mm thick. Consequently the molds were produce on the X-One MFlex printer of Quebec Metallurgy Center - CMQ. A dozen castings were produced with different casting temperatures and filling times so that it was possible to assess under which conditions complete filling of the mold cavity would be achieved. Filling and solidification modeling allowed predicting misruns and metallurgical properties inside the A356 (AlSi7Mg04) casting.INTRODUCTION Recent advancements in additive manufacturing enable foundries to produce molds without the tooling (pattern and core boxes) necessary when conventional technology is used (Eyad, 2016). This is particularly advantageous when dealing with intricate shapes and/or when a limited number of parts must be produced within a few days rather than in 5 weeks. An additional advantage is gained when producing prototypes (Johnson, 2016) as changes are much less costly and time consuming when made on a numerical 3D drawing rather than on patterns and core boxes. 3D printing is normally economical for a small number of parts; however, if the part is not too big and very intricate in shape such as the part that will be studied in the present work, 3D printing can be economical even for an important number of castings to be produced. On the other hand, low pressure casting is a high integrity casting process in which the mold cavity is filled from the bottom via a transfer tube in which the liquid aluminum rises under the pressure applied at the surface of the melt as illustrated in Figure 1. The filling can thus be precisely controlled, eliminating the turbulence created when the mold is filled from the top (gravity casting). Also, the pressure applied on the melt during solidification results in excellent feeding of the casting when conditions of directional solidification are met. In the present work, the compressor impeller shown in Figure 2 will be sand cast by low pressure."

Jan 1, 2018

By R. D. Clarke, E. De Souza

"A framework for ventilation planning, with a focus on planning to the end-of-mine life, was developed for the Diavik Diamond Mine, Northwest Territories. This framework was successfully used by Diavik’s mine engineers to select a cost-effective ventilation plan that met the life-of-mine requirements. The framework achieved this result by reconciling the production plan with the ventilation plan. A set of design acceptability criteria was created and a PICK (possible, implement, challenge, kill) chart was used to quickly narrow down the generated ideas for detailed assessment and economic analysis. RÉSUMÉ Un cadre de planification de l’aérage, qui met notamment l’accent sur la planification jusqu’à la fin de vie de la mine, a été développé pour la mine de diamants Diavik. Les ingénieurs miniers de Diavik ont su mettre à profit ce cadre pour sélectionner un plan d’aérage rentable qui répondait aux exigences propres à la durée de vie de la mine. C’est en conciliant le plan de production et le plan d’aérage que cet objectif a pu être atteint. Un ensemble de critères d’acceptabilité de la conception a été créé et un tableau PICK (de l’anglais possible, implement, challenge, kill, une méthode donnant la priorité à certaines actions proposées ou à des idées visant à résoudre des problèmes) a été utilisé pour rapidement limiter les idées générées et les soumettre à une évaluation et une analyse économique détaillées.INTRODUCTION The Diavik Diamond Mine, Northwest Territories, has been an underground-only operation since 2012 and has a remaining mine life of 8 years. In the first year of underground-only operations, the production rate increased from 60 kt of ore per month to more than 160 kt of ore per month. In subsequent years, this rate was continuously increased (Table 1) because the operation went through various improvement initiatives. By the end of 2016, Diavik’s total production was 0.41 Mt (+22.8%) ahead of the 2012 budget for 2016 production."

Jan 1, 2018

By C. S. Chen, Y. J. Luo, M. W. Gao, B. Li, Z. F. Zhang

"To obtain large-sized billets with fine grains and homogeneous elements distribution, uniform direct chill (UDC) casting process, based on annular electromagnetic stirring coupling with intercooling, was employed to produce 7055 alloy billets with a size of F584 mm in this study. The results indicated that there were the coupled effects of annular electromagnetic stirring and intercooling on grain refinement and element homogenization, and also the billets produced by the UDC casting process showed excellent hot workability in comparison to the normal direct chill casting process.INTRODUCTION The high solute 7055 aluminium alloy has a wonderful combination of high specific strength and hardness, good resistance to stress corrosion cracking and high fracture toughness, which is very useful in aerospace application (Yan et al., 2013; Mondal & Mukhopadhyay, 2005). The production of large-sized 7055 alloy billets with high quality is the basic condition for the subsequent application of 7055 alloy to the aircraft. Inhomogeneous microstructures and performances of 7055 billets result from the high alloying element content and the inhomogeneous cooling condition in different regions of billets during the conventional direct chill casting (Paramatmuni et al., 2004; Lalpoor et al., 2011), which will bring bad influence to processing property, functional performance and utilization rate of materials. To alleviate segregation and obtain fine and uniform grains, some effective treatment methods were proposed including electromagnetic stirring (EMS) (Vives, 1989), ultrasonic vibrating (Zhang et al., 2011) and melt conditioning (Fan et al., 2013), on the melt to obtain fine and uniform grains. However, these methods could not effectively decrease the large temperature difference between central and periphery parts of the billet, because the solidification mainly depends on outside cooling including mould cooling and water spraying cooling. To change the heat extraction pattern of the billet functioned solely from the outer surface, based on annular electromagnetic stirring (A-EMS) invented by Xu et al. (2010), Luo et al. (2017) proposed uniform direct chill (UDC) casting coupling A-EMS with intercooling in the direct chill (DC) casting process. An in-mold cooler was inserted to the melt sump, and thus the alloy melt temperature and concentration at solidification front become more uniform."

Jan 1, 2018