Search Documents

By Rafic Moubarac

FRP (Fiberglass Reinforced Polyester) equipment has been used in different and several applications during metals processing and extraction, and the hydrometallurgical process. Case histories of such equipment will be shown of major projects worldwide.

Jan 1, 2015

By Baisheng Nie, Longlong Yang, Tao Yang, Wenjie Jia

"Gas adsorption in coal is an exothermic and physical process. Temperature might change during the dynamical process. In order to get the temperature variation of gas adsorption process, the experiment system which can test the temperature variation and analyze the thermal effect was established. Gas adsorption experiments under different conditions were done by using the test system. The results show that temperature increases during the adsorption process. It is an exothermic reaction process. Also, the temperature variation and the variation gradient increase with the increasing of equilibrium pressure. The temperature variation value is smaller if the experiment temperature is higher. The paper will provide basic experimental data for explaining gas adsorption mechanism better.INTRODUCTIONChina is the largest coal producer in the world while it also has the most serious coal mine disasters. According to the statistics, there are nearly a thousand coal mines in China including more than 110 the key state-owned mines risking to happen coal and gas outburst. Hundreds of coal and gas outburst occur each year which often causes serious casualties and economic losses (State Administration of Work Safety, 2007). With the continuing exploitation of the coal resources, the depth of the Chinese coal mines increases about 100 meters every year which causes the situation of gas accident becoming more and more serious (Xie et al., 2006).At present, the real mechanism of gas adsorption, desorption and the diffusion process in coal and the influence factor of it are not so clear. And because of the limit of prediction method and the technological level caused gas accident prevention theory and technology not so valid."

Jan 1, 2015

By R. Chen, K. Xia

In deep mining activities, blasting induced compressive stress wave would be reflected as tensile wave at a free surface around the openings, which would facilitate the tensile failure of the deep rock since it is much weaker in tension than in compression. It is thus critical to understand the dynamic tensile failure of rocks subjected to static tension for deep rock engineering applications. A modified split Hopkinson pressure bar (SHPB) system is adopted to load Brazilian disc (BD) samples statically, and then exert dynamic load to the sample through stress wave generated by impact. The pulse shaper technique is used to generate a slowly rising stress wave and thus to facilitate the stress equilibrium of samples during each test. Five groups of Laurentian granite (with tensile strength of 12.8 MPa) BD samples under the pretension stress of 0 MPa, 2 MPa, 4 MPa, 8 MPa, and 10 MPa are tested under different loading rates. The result shows that the dynamic tensile strength of the rock decreases with the increase of pre-tension stress, which is easy to understand because pre-tension stress weakens the rock sample. It is also observed that under the same pre-tension stress, the dynamic tensile strength increases with the loading rate, revealing the so-called rate dependency that is common for engineering materials. Furthermore, it is found that the loading rate sensitivity of the rock increases with the increase of pre-tension stress. A qualitative explanation for this phenomenon is that more microcracks are generated and activated under higher pretension stress, resulting in a more viscous material. Based on the results, an empirical equation is proposed to fit the data and explain the dynamic tensile behaviour of rock under pre-tension stress. A physical model is used to simulate the dependency of the dynamic tensile strength of rock on the pre-tension stress and the loading rate, which is shown to be in good agreement with the experimental results.

Jan 1, 2015

By P. Nos, L. Kolbeinsen, M. W. Kennedy, A. Filzwieser, R. T. Jones, A. MacRae

Modern furnace designs often incorporate extensive use of cooled elements to achieve long campaign lives at high operating intensities. However, contact between water and high temperature fluids can result in powerful Boiling Liquid Expanding Vapour Explosions (BLEVEs). Therefore cooling such elements with water carries inherent risks when used under slag and particularly below molten metal or matte. Alternative cooling media exist that can reduce or eliminate the risk of BLEVEs. These media are analysed and discussed in the context of deeply cooled furnace elements. Important factors in selecting alternative coolants are explored including: critical heat flux, thermal limits, toxicity, flammability, unit cost, etc. Key cooling system design criteria are reviewed in the context of both traditional and alternative coolants. Results of Computational Fluid Dynamics are presented for an example tap-block cooler design using a number of selected coolants. Research needs to advance the safe use of alternative coolants are presented.

Jan 1, 2015

"Gravity concentration remains the main separation method for fine iron ore and is used extensively for treating various minerals. Gravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid, such as water or air (Wills, 2006).Spirals concentrators are one of the gravity concentration equipment used for beneficiation of minerals. Spirals are typically used for processing of fine minerals (-1mm) size fraction. The main operating variables for a spiral concentrator are the feed rate, the solids concentration, the wash water addition and the position of the cutters or splitters used to separate the tailings, middling and concentrate streams (Sadeghi, Bazin & Renaud, 2014).The aim of this study is to investigate the effect of feed rate, solids concentration and wash water on grade and recovery on iron ore material. The Multotec SC20HC/7 WW spiral was used for the experimental test work. The spiral was tested at varying solids concentration and feed rate. The wash water rate was also varied to establish the best washing rate. The splitter positions were kept constant. Optimization of these variables is expected to provide optimum conditions for a good compromise between grade and recovery.INTRODUCTIONSpiral concentrators are simple low energy consuming devices that separate minerals mainly on the basis of density. Spirals are widely used in mineral processing as a method for preconcentration and have proven to be metallurgically efficient and cost effective.Spirals have a wide application, they are used in iron ore processing, coal, gold, chromites, mineral sands, glass sands, and in soil cleaning.Separation on a spiral is achieved through a combination of forces that act on particles as they move down the trough of the spiral. The main forces known to act on the particle on a spiral are the gravitational forces, centrifugal force, hydrodynamic drag, and lift and friction forces (Kapur & Meloy, 1998). Apart from the forces acting on a spiral, the properties of the slurry flowing on a spiral including, solids concentration, feed rate and wash water also plays an important role in the separation on the spiral.The relationship between separation efficiency and feed rate was shown to be linear, with a decrease in efficiency at higher flow rates. Previous work on flow profile by Holland - Batt (1990) indicated that any increase in the feed rate to a spiral results in a greater part of the additional flow volume reporting to the outside of the trough. The flow on the outside of the trough becomes energized and consequence to that the heavy particles find it hard to settle and escape this region to the inner region. This effect has a high impact on recovery of heavy minerals, since any increase in volumetric flow on the spiral is not made available for recovery in the inner region of the spiral."

Jan 1, 2015

By K. C. Corin, Z. G. Song, J. G. Wiese

In the present study the effect of using different grinding media, viz, ceramic balls, forged steel balls, 15% Cr steel balls, stainless steel and mixture of stainless steel and 15% Cr steel balls (50:50) on the flotation performance of a Platinum Group Mineral (PGM) UG2 ore was investigated. Test work was conducted using a laboratory scale horizontal tumbling mill and a batch flotation cell. Power draw to achieve a specific P80 was determined for each media type. Changes in flotation behaviour were evaluated in terms of particle size distribution, water recovery, solid recovery and valuable mineral recovery. pH, Eh and DO levels were also measured. Grinding products of five different media produced similar solids and water recovery, which is indicative of the froth characteristics, but the grades and recoveries of PGE and chromite were different. The product obtained when using ceramic media showed the best flotation performance, producing the highest PGE recovery and the lowest Cr2O3 recovery. The products obtained when using stainless steel balls (SS) produced the lowest PGE recovery and highest Cr2O3 grade and recovery. The paper proposes possible reasons to explain these observations which may have significant importance for the operation of a PGM concentrator.

Jan 1, 2015

By Xiaoqiong Wang, Daobing Wang, Fanbao Meng, Jianbo Wang, Hongkui Ge

"Shale gas has become an important unconventional oil and gas resources. Its effective development relies on comprehensive and accurate understanding of shale gas reservoirs. Rock mechanical properties is one of the important components of reservoir evaluation. Two adjacent black shale samples, which are cored from the depth of 1145 meters in Chongqing, southwest China, are subjected to acoustic emission(AE) test under uniaxial stress and compared with coarse grained granite. The results of synchronous AE, stress-strain and ultrasonic velocity experiments show that shale has weak anisotropy. Compared with granite sample, two shale samples are similar, but their strength, velocity and brittleness are quite different, indicating that shale has strong microscopic heterogeneity. TOC, XRD, SEM microstructure analysis show that total organic content, mineral composition and natural fractures are the main impacting factors for mechanical heterogeneity. INTRODUCTIONShale gas is a typical low-grade marginal resource, which is characterized by ultra-low matrix permeability and small single well control volume. In order to enable commerical development, complex hydraulic-fracture networks must be created in the shale to allow gas to escape from the micro/nano-pores and natural fractures where it is trapped in the rock (C. Clark et al.,2013; Ge et al., 2013). The development of shale gas requires accurate evaluation methodologies to evaluate shale reservoir properties and predict production. (Jarvie et al., 2007). Rock mechanical properties are an important part of the reservoir evaluation. It is significant for efficient drilling, completion and hydraulic fracturing to understand mechanical behavior of shale gas play (John, 2011; Wei, 2013).Rock mechanical properties mainly include heterogeneity, anisotropy, brittleness and acoustic emission activity (Lockner et al., 1992; Jerome et al., 2009; He et al., 2010; Liang et al., 2012). Shale mechanical properties are evaluated from laboratory tests following a complex workflow that covers tasks from sampling to testing (Md. Aminul Islam et al., 2013). It is common to include various experimental methods such as stress-strain curves, ultrasonic velocity and acoustic emission when evaluating the mechanical properties (Rao et al., 2006). Because of the presence of organic-rich matter, mineral composition orientation and natural fractures, shale tends to have strong anisotropy and heterogeneity (Deng et al., 2004; Wang et al., 2013; Hathon et al., 2013)."

Jan 1, 2015

By D. R. Schmitt, N. Ong, R. S. Kofman

Shales and mudstones comprise about 75% of all the sedimentary rocks. In, particular, organic rich shales are considered as a petroleum source rock and more recently with the advent of hydraulic fracturing technology to be a reservoir in their own right. In this sense, the aforesaid motivates our work with laboratory measurements of elastic properties of these geologic materials, which are known to be anisotropic. As such, assuming Vertical Transverse Isotropy (VTI) symmetry, the dynamic and static moduli of a series of cores from various geological formations in Alberta, Canada are simultaneously investigated as a function of confining pressure using the ultrasonic pulse transmission method and strain gages. Dynamic moduli were obtained from ultrasonic P- and S-wave velocities measured on a prism cut with faces perpendicular, parallel and oblique to the assumed vertical axis of symmetry. Static moduli were calculated from strain-stress curves obtained along the directions perpendicular and parallel to the assumed axis of symmetry as well. Velocity measurements show that samples are highly anisotropic, but that the pressure-dependent behaviour of the wave speeds differs. VP(90°) and VSH(90°) both with layer parallel propagation and polarizations change little with pressure while VP(0°) and VS(0°) (both with layer perpendicular propagation) display significant nonlinear responses particularly at pressures < 25 MPa. These characters transfer to the derived full set of elastic constants. In order to effect a proper comparison of the dynamic and static moduli, we convert the dynamic elastic constanst to linear compressibilities pependicular (Kdyn1) and parallel (Kdyn3) which are directly comparable to the static tangent compressibiities obtained by differentiation of the observed strains. Both sets highlight the anisotorpic nature of the material but most interestingly Kdyn1 _ Ksta1 but Kdyn3 > Ksta3 by nearly 40% for one of the samples. The other samples measured respond similarly suggesting that conceptually the structure of such materials could be considered to be constructed of alternating stiff or compliant layers. This finding has implications in the response of the formation to stress particularly during hydraulic fracturing and the interpreation of acoustic logs in providing appropriate measures of elastic properties for engineering purposes.

Jan 1, 2015

By Mike Fontaine

The success of a project is defined by meeting the financial performance objectives of the business case within a stipulated timeframe. Early in design, little information is normally available; the uncertainty introduces risk to the project outcome. Using a range of risk management tools and techniques, a project can be developed from front end loading phases 1 through 3 (FEL1–FEL3), and project implementation (FEL4) and then into operations with an optimized probability of success. For every project element, the risk management framework embodies: establishing a context; assessing risk (identify, analyze, and evaluate); and treating risk. Embedded within design activities, this process mitigates or eliminates risks. Monitoring and control, as well as extensive communication and consultation with stakeholders, is integral to the risk management process.

Jan 1, 2015

By N. Gharib, F. Hassani, P. Nekoovaght

"Novel rock breakage techniques are becoming more viable and attractive to industry. Microwave energy, as a thermal energy capable of inducing micro cracks through differential heating (therefore expansion) is a technology gaining considerable attention in mineral processing and ore comminution applications. Recently, the use of microwave radiation has been evaluated as a possible avenue for terrestrial and extra-terrestrial drilling applications as well as full face tunneling or rock breaking machines. As part of an overall research on use of microwave in rock breaking systems, the influence of microwave energy on the mechanical properties of common hard rock types as basalt has been investigated. The results revealed that microwave energy irradiation imposes micro and macro cracks to the surface of the rock being irradiated. In explosive free tunneling applications using TBM, jointed and cracked surface of rock eases the cutting process and increases penetration rate. The experimental setups have been simulated with the help of a multi-physics numerical modeling and the results have been compared with practical experiment. The wave propagation of microwave has been simulated and the distances where the power intensity is higher are identified. Experimental and simulation results underlined the potential impact of the use of microwave energy in underground or surface excavation applications such as mining and tunneling. This will also contribute economically when mine-to-mill operation is fully considered to improve the efficiency of rock crusher stages. INTRODUCTIONDuring hard rock breakage (i.e., separation of a piece of a rock from its parent deposit) in mining and civil applications, the performance of mechanical equipment such as tunnel boring machines (TBMs) is limited by high levels of bit wear and maintenance. Preweakening natural rock prior to breaking it by machine is one approach to lower bit wear and maintenance costs. Some preweakening methods apply heat directly or indirectly. For example, flame torch-assisted TBMs (Lauriello et al., 1974; Resource Technology, 1984) have been deemed economical in terms of equipment, but their feasibility is limited by high fuel consumption. Microwave energy could offer several advantages over the flame torch method: it does not produce emissions or increase fuel consumption (electricity source is available on the machine), and is easy to control (quick power on and off)."

Jan 1, 2015

By M. R. Henzinger, W. Schubert

"The quality of the backfill applied at a shield driven tunnel is of significant importance failure of the lining. The used material also affects the interplay between support and excavation behaviour.In this research the state of the actual bedding situation is investigated by an analytical approach, laboratory tests and numerical simulations. The numerical simulation using continuum methods have shown shortcomings. These shortcomings regarding the instability of large strain simulations restrict the possibility to reproduce the relocation of the backfilling material. The performed scaled model tests have shown that the regripping process of a double shielded tunnel boring machine affects the soil failure within the gap. With the analytical results the influence of the wall friction can be predicted. Therefore the angle of the failure surface can be determined. The results have shown that the wall friction significantly increases the failure angle. INTRODUCTIONFor tunnel boring machines (TBM) with single (SM) or double (DSM) shield, precast liningsegments are used as rock support. These segmental linings are installed within the protection of the TBM shield. In order to reduce the friction while advancing, the shield diameter is smaller than the diameter of the cutter head and therefore also smaller than the excavation boundary. The difference depends on the expected radial convergences. Since the lining segments are mounted within the shield the steering gap between the shield and the excavation boundary increases and is hereinafter called annular gap.In the process of tunneling in hard rock, the annular gap is usually filled with fine grained and closely graded gravel, termed as pea gravel. The backfilling process starts as soon as possible after the shield tail passes the lining. Due to the operational procedure within the working area of a TBM, a fully backfilled annular gap might not be established after every ring closure. This leads to an unfavorable distribution of the pea gravel leaving the segmental lining partially without bedding. Segmental linings can develop sufficient resistance only when properly bedded."

Jan 1, 2015

By R. B. Kaunda

One fundamental requirement for surface and underground rock engineering is the ability to characterise the rock mass. An accurate characterisation of the rock mass allows rock engineers to optimize designs safely and economically. A number of classification systems have been developed in the past 50 years to help characterise rock masses such as RMR, Q system, Rmi, and several others. The challenge in developing rock characterisation schemes is often practicality, i.e. creating systems with relatively simple inputs for the everyday practitioner. A second challenge is the degree of subjectivity often inherent in commonly used classification systems. These challenges are especially exacerbated in weak rock or densely jointed rock masses. This paper introduces a new approach to characterise densely jointed rock mass using artificial neural networks and principal component analysis, based on principles commonly used in the geotechnical engineering of rock fills and waste rock dumps. Thirteen input parameters are dimensionally compressed using principal component analysis. Using a global database with more than 100 case histories, an artificial neural network is developed to conduct the rock mass characterisation. The advantage of this approach is less subjectivity as commonly used engineering (quantitative) terms are put to use. A further advantage is that given that the method is site-data dependent, it allows for ‘fine tuning’ of the model for a specific site.

Jan 1, 2015

By H. Rafiei Renani, C. D. Martin

"The Cohesion Weakening Friction Strengthening (CWFS) is adopted in numerical analysis to capture the observed progressive failure of hard rock pillars. As a case study, pillars at the Elliot Lake mines with width to height ratios of 0.5 to 3 were analyzed in FLAC3D. Pillars with width to height ratios of 0.5 and 1 show a very similar strain softening behavior while with width to height ratios of 2 and especially 3 indicated prolonged strain hardening. The CWFS model successfully captured the mechanism of progressive failure observed in hard rock pillars including initiation of spalling at the corners, progress of spalling towards the centre and formation of hour-glass shaped pillar, and eventually shearing through the width of pillar. Both the CWFS model and site specific empirical formula successfully separated the stable and failed cases in the Elliot Lake mines. While both models are in reasonable agreement for width to height ratios of less than 2, the empirical formula gives increasingly lower strength values for wider pillars which may result in excessively conservative and uneconomical design.INTRODUCTIONPillars are the portion of in situ rock left between the adjacent openings to maintain the stability of excavations. Conditions of equilibrium require that the loads previously carried by the excavated rocks be transferred to the pillars resulting in elevated stresses within the pillar. Hence, prediction of the behavior of pillars under these loads is important for underground design. Determination of the strength of pillars is a classic subject in underground mining. In conventional mining methods such as room and pillar operations, economic incentives point towards higher excavation ratios i.e., leaving smaller pillars between the mined excavations, while safety and stability requirements favor wider stronger pillars. In some mining methods such as caving operations, the problem is even more challenging. On one hand, the whole operation is directly dependent on the proper continuous flow of caved ore between the drawpoints which requires optimizing the spacing between drawpoints and thereby often leaving narrower pillars. On the other hand, the pillars should be wide enough to ensure the safety of mining operation. Both the blockage of drawpoints as a result of wide pillars and uncontrolled failure of narrow pillars can jeopardize the investments and mining operation.Therefore, design of pillar poses a somewhat unique challenge to rock engineers where simple conservative approaches frequently used in other design methods are no longer acceptable. The behavior of pillar under elevated loads should be predicted accurately."

Jan 1, 2015

By J. Ambrose, R. W. Zimmerman

"Shales are highly anisotropic in their mechanical behavior. The strength ( ??1) of anisotropic shales depends not only on the magnitude of the other two principal stresses ( ??2, ??3), but also on the bedding plane orientations (?) relative to the principal stresses. In this study, the role of the intermediate stress ( ??2) on the strength of shale is evaluated using new data from triaxial compression and extension tests. To understand the failure behavior of shales, we have carried out triaxial compression tests ( ??1 > ??2 = ??3) on two organic rich mudstones, at different confining stresses and loading angles. We first fit the triaxial compression data with Jaeger’s plane-of-weakness model, and find that the model is able to represent the strength behavior of anisotropic shales reasonably well. We then carried out five triaxial extension tests ( ??1 = ??2 > ??3) for a high strength-anisotropy shale, and two extension tests for a low strength-anisotropy shale. Results from the compression and extension tests for failure along the weak plane shows that the role of ??2 is not significant for weak plane failure. However, for the low strength-anisotropy shale, the failure strength of the intact rock (i.e., at ??= 0o and 90o) for compression and extension tests were significantly different. This indicates that for intact rock failure, the role of ??2 is important and cannot be ignored.INTRODUCTIONFor many years, various researchers have studied the roles of ??2 for failure of isotropic rocks. (Mogi, 1967 and 2007; Colmenares and Zoback, 2002; Al-Ajmi and Zimmerman, 2005 and 2006; Haimson, 2009; Ma and Haimson, 2012). The findings from these studies show that the effect of ??2 on the strength of isotropic rocks is generally significant, and cannot be ignored.Since the role of ??2 in the failure of isotropic rocks was recognized, other researchers attempted to extend some of these isotropic failure criteria to anisotropic rocks, but with limited success (e.g., Tiwari & Rao, 2007; Singh et al., 1998; Zhang and Zhu, 2007; Pei, 2008). Smith and Cheatham (1980), on the other hand, conducted true-triaxial experiments on the Green River Shale and used a J2-I1 type relationship to predict the strength behavior, but without considering the effect of the three-dimensional orientation of the weak plane on strength. Therefore, unlike for the case of isotropic rocks, additional studies need to be done to determine the role of 2 on the failure of anisotropic rocks."

Jan 1, 2015

By S. Hon, C. Searcy, R. DasGupta, B. Fleet, A. Davidse, A. Pringle

"The mining industry is facing serious long- and short-term challenges relating to uncertain commodity prices, environmental pressures, and margin compression due to rising energy costs. Energy issues, formerly treated as an operating cost, are changing as executives search for longer term solutions to deal with uncertain fossil fuel prices and greenhouse gas emissions. Consequently, mining executives are increasingly willing to consider introducing a proportion of renewable energy (RE) systems into the mine energy mix. This paper examines how RE can be successfully integrated at mine sites, as well as some of the benefits and barriers to their wider adoption.RÉSUMÉ L’industrie minière fait face à de sérieux défis, à long et à court terme, en raison de l’incertitude des prix des matières premières, des pressions environnementales et des compressions de la marge bénéficiaire dues à la hausse des coûts de l’énergie. Les questions énergétiques, auparavant considérées comme un coût d’exploitation, changent alors que les cadres cherchent des solutions à plus long terme afin de prendre des mesures pour contrer les prix incertains des combustibles fossiles et les émissions des gaz à effet de serre. C’est pourquoi les cadres miniers sont de plus en plus disposés à considérer l’introduction d’une proportion de systèmes d’énergie renouvelable dans l’équation énergétique de la mine. Le présent article traite de la manière dont les énergies renouvelables peuvent être introduites avec succès aux sites miniers ainsi que quelques-uns des avantages et des barrières à leur application à une plus grande échelle."

Jan 1, 2015

By G. F. Liu, S. Owada

Platinum Group Metals (PGMs), Pt, Pd, Rh, have been widely used as a three-way catalyst to clean discharged gas from automobiles and therefore a considerable amount of the spent catalysts is generated annually. This paper proposes a novel concentration technology of PGMs by utilizing the double-deck structure of PGM bearing alumina-ceria and cordierite phases. The applied technologies are a combination of heating-quenching, selective grinding and screening for separating alumina-ceria phase from cordierite. Temperature change as a function of quenching time and the thermal stresses applied to both phases were simulated and calculated by FEM, and it was clarified the mechanism of micro-cracks generation at the phase boundary and micro-cracks in alumina-ceria phase, which indicated that separation of alumina-ceria phase from cordierite and selective breakage of alumina-ceria phase could be achieved in the subsequent selective grinding with an attritor. This process could concentrate 46 wt% of alumina-ceria phase into fine fractions with 86 % recovery efficiency. The remaining alumina-ceria phase can be further recovered by applying flotation and so on.

Jan 1, 2015

By J. Duriez, L. Scholtès, F. V. Donzé

"Fracture propagation process in brittle rock is investigated by means of numerical simulations performed with an adapted formulation of the discrete element method. The progressive failure mechanism is simulated through the breaking of the bonds making up the cohesion between the elements constituting the simulated medium. The use of appropriate contact laws associated to a near neighbor interaction feature provide the model the ability to reproduce fundamental characteristics of brittle rock behavior such as, for example, high values of the tensile to compressive strength ratio. Great attention is given to accurately describe the properties of the pre-existing joints or faults in the model. A specific joint model gives the possibility to define a tailor-made behavior of the discontinuity surfaces without suffering from discretization bias.Compression test simulations are performed on pre-flawed samples and compared to experimental results in order to validate the numerical approach for describing the initiation and propagation of fractures in brittle rock under mode I+II loading. It is shown that the crack mechanical parameters can greatly influence the fracturing pattern, in particular its frictional properties. Overall, the numerical simulations reproduce fairly well the failure patterns that are obtained experimentally.The discrete model is then used to study mode I+III loading to give an insight into fracturing problems occurring at the scale of the continental crust. The ability of the model to support mechanically the physical modelings performed with wet clay or sandbox is shown. As an example, the model is used to track the development of a twist crack system (wrench fault) through the nucleation and coalescence of microcracks."

Jan 1, 2015

"As part of a series describing the nickel operations of Vale Canada (formerly known as Inco), this paper focuses on the 1973 to current operations of the Copper Cliff nickel refinery in Ontario, Canada. The process used there employs the formation of Ni tetracarbonyl at high CO (gas) pressure and its subsequent decomposition at somewhat elevated temperatures to produce highly pure Ni pellets and powders. Personal sampling of workplace aerosol dusts is reported, with information on specific Ni compounds in the aerosols.RÉSUMÉ Dans le cadre de la série d’articles décrivant les opérations de nickel chez Vale Canada (anciennement Inco), le présent article cible les opérations de 1973 à ce jour à l’affinerie de nickel de Copper Cliff en Ontario, Canada. Le procédé utilisé à cette usine est la formation de tétracarbonylnickel sous une pression élevée de CO (gaz) et sa décomposition subséquente à des températures plutôt élevées pour produire des granules et des poudres de Ni pur. Un échantillonnage par l’auteur des poussières en aérosol est présenté ainsi que de l’information sur les composés spécifiques de Ni dans les aérosols."

Jan 1, 2015

By Z. Abbasloo, A. Masoomi, L. Ebrahimi, A. Mortazavi, A. Keshavarz

"Investigation and 3D analysis of Heap no. 2 of Meydook copper complex was the subject of this study. In this project all geological and geotechnical investigations conducted in the mine were evaluated aiming at determination of Heap no. 2 design parameters. The main objective of the project was to evaluate the potential for construction of Heap. No. 2 on a waste dump built in a valley in the north side of the pit.Considering the space limitation for dump location this was a viable alternative to reduce the costs associated with heap no. 2 construction. Moreover, it allowed for a significant reduction in overall mining costs. Considering the project condition, a 3D analysis of heap major structures including; valley rock foundation, waste dump, and low grade ore was carried out. Five sets of analyses were conducted and the displacement and stress fields were calculated within the heap no. 2 components. In all analyses conducted the subsident profile was determined for the valley base rock and heap foundation (waste dump). Moreover, the shear interaction between heap and waste dump was evaluated at the heap interface. The analyses results showed that the maximum settlement at the heap base is about 4-5 cm and the waste dump provides a safe and reliable base for heap construction. Moreover, the analysis results showed that the selected %5 grade for the heap interface is good and does not pose any risk in terms of heap Interface shear displacements. A sensitivity analysis of heap mechanical parameters was also conducted. The obtained results show that if the friction angle of heap material is reduced below 25 degree due to acid spraying process, the heap walls become unstable and the heap geometry must be redesigned."

Jan 1, 2015

By M. Nakai, G. Itoh, R. Yamada, A. Kurumada

In order elucidate the mechanism for poorer fatigue properties of 7000 series aluminum alloys than those of 2000 series alloys, the effect of the test environment on the fatigue crack growth of the two series alloys was investigated, considering the relationship to hydrogen embrittlement. Two 7075-type and four 2024-type alloys were T6-tempered and T4-tempered respectively, and subjected to fatigue crack growth tests in moist and dry environments. When tested in moist air, fraction of intergranular crack path was higher in the 7075-type alloy with coarse equi-axed grains than in the 2024-type alloy with similar microstructure. This was in accord with the larger crack growth rate in the 7075-type alloy. Both the intergranular crack path fraction and the crack growth rate were decreased by changing the environment to the flow of nitrogen gas. Thus, the large fatigue crack growth rate of the 7075-type alloy is attributable to hydrogen embrittlement.

Jan 1, 2015