Search Documents

By José L. M. Clemente, John R. Davie

"Abstract An extensive pre-production static and dynamic pile load testing program was conducted for a coal-fired power plant. The static load testing program included axial compression, uplift (tension), and lateral load tests. Three types of piles were tested: Monotube, closed-end pipe, and step-tapered. The load tests were used to (a) determine pile driveability characteristics for each pile, (b) verify pile load response behavior, and (c) provide data to support the selection of a cost-effective piled-foundation system for the plant. A recent publication (Clemente and Lewis, 2013) describes the compression load testing program, the interpretation of instrumentation measurement results, and pile selection criteria. This manuscript describes site subsurface and groundwater conditions and installation of probe piles for testing, focuses on the uplift and lateral load testing program, and provides a comparative interpretation of the load test results.INTRODUCTIONThe pre-production probe pile load testing program described here was conducted for a 202-megawatt, coal-fired power and steam generating (cogeneration) facility. A schematic layout of the main plant (power block area) is shown in Figure 1, which also includes the locations of clusters of preproduction probe piles and boreholes drilled near these clusters.The load testing program included 24 pre-production probe piles driven throughout the power block area. The probe piles were driven at locations T-1 through T-8, shown in Figure 1. Three types of piles were driven at each location: Monotube pile; closed end, straight shaft pipe pile; and step-tapered pile. At each location, the three piles were driven in a row with the pipe pile at the center, and the center-tocenter spacing between piles was equal to about 1.5 m (> 3.5 pile diameters for the largest pile). No pile cap was used to connect the three piles, and the three piles driven at locations T-1 through T-8 will be referred to as pile clusters. A complete suite of static load testing (compression, tension, and lateral) was performed on each individual pile at Cluster T-2 and on the step-tapered piles only at Cluster T-8, shown in Figure 1.Clemente and Lewis (2013) provide details of the compression load testing program, the interpretation of instrumentation measurement results, and pile selection criteria. This manuscript focuses on the uplift (tension) and lateral load testing program. A brief summary of the site geology and existing subsurface and groundwater conditions in the vicinity of the test pile clusters is presented, with emphasis on T-2 and T-8. Probe pile driving results at T-2 and T-8 are also presented. Descriptions of the static uplift and lateral load test program at T-2 and T-8 are given along with a comparative evaluation of the load test results."

Jan 1, 2014

By Helmut Hass, Marco Ziller

"Abstract: 1 Sophia Spoortunnel Marco Ziller, Trevi S.p.A.:For the construction of 14 cross passages connecting the twin tunnels of the Sophiaspoortunnel the Artificial Ground Freezing technique was applied as temporary soil improvement. AGF by Brine and Liquid Nitrogen was implemented. Automatic data acquisition and recording systems were installed to monitor the variation of the temperatures in the soil during the freezing intervention in order to control the behaviour and the efficacy of the treatment.IntroductionThe Sophia rail tunnel is a bored tunnel with a length of 4.24 km, comprising two separate parallel tubes with an outside diameter of 9.45 m. The twin tunnels were excavated by a TBM equipped with hydroshield. Seven service shafts, approximately 30 m deep, were constructed in between the tunnels. From each shaft two cross passages were constructed connecting the shaft with both tubes, for a total of 14 cross passages.The Artificial Ground Freezing technique utilizing both the Brine and Liquid Nitrogen methods was used for temporary waterproofing and soil support to allow the excavation of the cross passages. The natural soil to be frozen was consisting in loose sand and clay under a hydrostatic pressure up to 250 kPa.For the measurement of the ground temperature. Automatic data acquisition and recording systems were installed to monitor the variation of the temperatures in the soil and at the contact with the tunnel lining. Furthermore, a comprehensive computerized system of sensors and cryogenic valves was designed and implemented in order to manage the whole Nitrogen process.Soil Main CharacteristicsThe soil stratigraphy is generally consisting in Clay (Holocene) from ground level to -15 m depth, followed by Pleistocenic Sand, from -15 to -25 m, and Clay below -25 m."

Jan 1, 2014

By Almer E. C. van der Stoel

"Abstract This paper deals with assessing the bearing capacity of existing wood pile foundations. With a wide range of restoration projects being performed in the Netherlands, on many locations deep excavations need to be constructed next to existing, many times listed buildings. The building are founded on piles that are often centuries old, so a close evaluation of the remaining bearing capacity, combined with and assessment of the influence of the excavation is in place.After giving an introduction on Dutch pile foundations, a methodology is described to assess the bearing capacity. Aspects as physical foundation investigation, determination of the current bearing capacity and a calculation of the bearing capacity in the new situation are discussed. The results of both analytical and Plaxis calculations are outlined, focussing on how to practically use this approach in renovation projects. Finally, cases studies of the successful application of this approach in major renovation projects in Amsterdam, such as the Conservatorium Hotel and the New Rijksmuseum are used to illustrate the successful application of this approach.A Short Dutch Pile Foundation History (based on Van der Stoel, 2001)The first houses built in Amsterdam, in the 12th century, were very light constructions of timber without foundations. Because of the soft peat layers found in Amsterdam, the houses there suffered from damage due to settlement. In the 13th century, castles and churches were increasingly built of bricks, which made it necessary to provide support for bigger loads. Under the wall of the construction a trench was dug, and this was filled on either side by alder fascines. Between the fascines small wood piles were driven (by hand) on which another series of fascines was put. On top of this construction, were placed oak slabs on which the bricks were then laid. From that moment on, a problem was caused by the decay of wood foundation elements in the humid soil. In 1503 a law was introduced forbidding building foundations on public streets without permission of the Building Inspection (to keep the fronts of the buildings in a straight line). In 1528 a law requiring permission from the local authorities for all building activities replaced this law. In this period developments started which led to the use of the type of foundation that can be considered the mother of the current “typical” Dutch pile foundation. The piles used in this period were shaft- bearing piles about 5 to 7 meters long. The mostly pine piles were driven between oak beams, which were placed on either sides of a trench, after which other oak beams were laid across at regular spaces: the so called “pile bent” pile foundation (Figure 1)."

Jan 1, 2014

By K. Rainer Massarsch, Bengt H. Fellenius

"Abstract Vibrations generated during the driving of piles or sheet piles can affect buildings or installations in the ground. However, observed building damage is not always caused directly by dynamic effects, but can also be related to foundation conditions. The importance of geotechnical conditions is usually not taken into consideration in most vibration standards. This paper describes how building foundations, and in particular mixed foundation types, are especially sensitive to ground vibrations. A method is presented for assessing the risk of settlement due to vibrations in granular soils. Also, a simple concept is proposed for estimating settlements in the vicinity of driven piles.1. INTRODUCTIONUnder unfavorable conditions, the installation of piles or sheet piles can cause damage to buildings or other structures on the ground. Frequently, such damage is attributed to vibrations of the building itself. In many countries, national or international standards are used to assess the risk of vibration damage to buildings. As such standards are often prepared by engineers with little or no geotechnical knowledge, the effects of ground conditions on vibration propagation and damage to building foundations are generally not recognized, and damage criteria based solely on the dynamic response of buildings neglect the importance of damage mechanisms governed by geotechnical conditions. One potentially important damage mechanism is differential settlement below buildings, especially when these are founded on loose granular soils. When seeking guidance in the literature, little or no information can be found regarding methods to assess permissible levels of ground vibrations with respect to risk for settlement.This paper focuses on building damage that can be attributed to foundation conditions. In the case of ground vibrations due to pile and sheet pile driving, differential settlements are of particular importance as the ground vibrations attenuate relatively rapidly from the source. Consequently, settlement below part of the building, which is located close to the vibration source, can be significantly larger than at a distance further away.Piles are often a cost-effective foundation solution for buildings on loose and compressible soil, frequently located in urbanized areas. Sheet piles are commonly used as support for deep excavations. While impact driving is most commonly used to install piles, vibrators are frequently used for driving (and extraction) of sheet piles. It is important to recognize the fundamental differences between impact and vibratory driving. During impact driving, the pile is subjected to stress waves of short duration. The driving process creates vibrations, which radiate from the shaft and/or the toe of the pile into the soil. The larger the intensity of the stress wave, the larger the dynamic force and the intensity of ground vibrations. In addition to the vibration intensity, which often is expressed in terms of particle velocity, also the vibration frequency is important. When the dominant frequencies of the generated vibrations harmonize with the resonance frequency of buildings or building elements, the risk of building damage increases."

Jan 1, 2014

By David L. Borusiewicz, M. Suri Surendra

"Abstract Helical piles have been used as anchors and for supporting lightly loaded structures as a method of underpinning, etc in the past. Recently, helical piles are being used to support new structures because of their simple installation process using relatively light and mobile equipment. This paper presents the results of evaluation and design performed for the temporary support of existing piers during a bridge rehabilitation project.INTRODUCTIONThe helical screw foundation was invented and patented by Alexander Mitchell in England in 1833. He installed screw piles to support lighthouses in the tidal basins of England. Many applications in the earlier years in the USA were in North Carolina and in Florida to support lighthouses (in coastal plain deposits). A lighthouse of similar foundation design is still in use at Key Biscayne, Florida.In the USA, the helical piles were reintroduced as foundation elements for electrical transmission towers. Helical piles were also used for anchoring guys of self supported towers and as tie-backs for excavation support systems. Typically, helical piles are being used for supporting lightly loaded buildings and for underpinning buildings undergoing distress as a means of remediation. The helical piles are not commonly used in the transportation industry.HELICAL PILESHelical pile is a segmented deep foundation system with helical bearing plates welded to a central steel shaft. Load is transferred from the shaft to the soil through these bearing plates. Central steel shafts are available in either a square shaft (Type SS) or a round shaft (Type RS). The Type SS series are available in 38 mm to 57 mm square sizes. The Type RS series are available in 73 mm to 114 mm diameter sizes. Type SS-RS combinations are also available for compression applications in soil conditions where dense/hard soils must be penetrated with softer/loose soils above the bearing strata.The leading segment consists of a shaft with one or more helical plates that are welded to the shaft. The plates vary in diameter from 203 mm to 355.5 mm and have a thickness of 9.5 mm or 13.7 mm. Typically the plate diameter increases from the bottom of the shaft upward. A helical bearing plate or helix is one pitch of a screw thread. All helices, regardless of their diameter, have a standard 76 mm pitch. Being a true helical shape, the helices do not auger into the soil but rather screw into it with minimal soil disturbance. Helical plates are generally spaced a distance of two to three times the diameter of the plate directly below in order for them to function independently as individual bearing elements. A typical detail of helical pile is shown on Figure 1."

Jan 1, 2014

By Mario Terceros H, Bengt H. Fellenius

"ABSTRACTThe city of Santa Cruz, Bolivia, is historically dominated by houses and three to five storey buildings.The geology in and around the city is such that even very light buildings need to be supported onpiles. The recent increase of the Bolivian economy, notably that of Santa Cruz, has created a demandfor new residential as well as office and industrial buildings, which mostly consist of multi-storey orhigh-rise buildings with significantly larger foundation loads. Foundation piles have become largerand longer, and the load on individual piles is increased. The development has resulted in an increasein the demand for more sophisticated design and construction methods and stricter approach toverifying the quality of the construction processes and results.This paper describes to geology of the Santa Cruz region and how the geotechnical conditions areconsidered in the design and construction of piled foundations. The improvement of past constructionand design techniques, based mostly on bored piles constructed with bentonite slurry, is beingreplaced with new methods of constructing bored piles, e.g. the Full Displacement Pile (FDP) andincorporation of techniques such as enlarging the pile toe, e.g., with the Expander Body. This paperpresents the results of several full-scale tests and discusses the incorporation of the test results indesign and construction.1 GEOLOGY OF THE REGIONSanta Cruz de la Sierra is located in the eastern lowlands and sub-Andean zone of Bolivia, SouthAmerica. The area lies at an elevation of about +400 m and the geology is a Paleozoic (250 millionyears old) sedimentary basin. The soils of interest to civil engineering construction are quaternarywith the dominant minerals being calcite, silica and feldspar. The main agent is the Piray River and itstributaries. Their past meandering over the area has resulted in a sedimentation-erosionsedimentationprocess and a profile dominated by fine to medium sands with intermittent layers ofclay or clayey sand. With increasing distance from the river, the clay-containing layers are thicker.Fig.1.- View of Bolivia with location of Santa Cruz and map of Santa CruzThe upper about 15 to 18 m thick part of the profile consists of normally consolidated layers of clays,silts, sands, in various combination and thickness. Below, the soil is more homogeneous and consistsmostly of sand and gravel. The groundwater table lies typically at a depth of about 6 m in the highestpart of the city and at about 1 to 3 m depth in the lowest part of the city."

Jan 1, 2014

By George Piscsalko

"Quality control of drilled shafts and CFA piles is greatly dependent upon the practices of the site personnel. In many applications it is difficult or not possible to fully inspect the shaft prior to concreting, such as when the shaft is drilled under slurry. CFA piles are cast with no ability to inspect the shaft prior to concreting. There are numerous methods currently available to assess the integrity of drilled shafts and CFA piles. This paper will compare evaluations by three existing non-destructive test (NDT) methods with a new method of Thermal Integrity Profiling for assessing integrity in drilled shafts and CFA piles. This Thermal Integrity Profiling method determines the integrity over 100% of the shaft cross section, both inside and outside the reinforcing cage, by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements are made typically only 12 to 48 hours after concrete placement, thus accelerating the construction process. Thermal Integrity Profiling will be described in detail and the Thermal Integrity Profile (TIP) results from several shafts with purpose built defects will be discussed along with several case histories from drilled shafts and CFA piles where Thermal Integrity Profiling was used. The case histories will compare TIP with various other NDT tests utilized on these particular piles including comparisons with Low Strain Integrity Testing and Cross Hole Sonic Logging. Test results for the various methods will be discussed and the excavation of the upper portion of one drilled shaft will be shown and discussed. IntroductionDrilled shafts can be a desirable foundation element in many applications due to the large axial and lateral capacities which are attainable for very large drilled shafts. Drilled shafts can be cast in a dry hole which allows for inspection of the hole prior to casting, but the casting process is very difficult to nearly impossible to inspect with any accuracy. Drilled shafts are frequently cast under slurry as a means to stabilize the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to accurately inspect the hole prior to casting and it is equally difficult to inspect the shaft during the casting process. CFA piles are another popular choice for their relative ease and speed of installation. The trend has been larger CFA piles carrying greater loads, which makes quality control critical for these piles. Many of the above mentioned processes are blind to inspection and therefore the chances increase for having defects present in the completed elements."

Jan 1, 2014

By David B. Paul

"ABSTRACTThe US Army Corps of Engineers (USACE) has 704 dams in their inventory and over 100,000 miles of levees with a capital value of over $150 billion. Currently, there are 319 dams that are classified as high hazard and have actionable failure modes that will require structural modifications. The most frequent actionable failure mode associated with the inventory is seepage and piping. One of the most effective engineering solutions is the installation of a cutoff to limit seepage. Currently, USACE has over $1.5 Billion of cutoff wall projects under construction and/or design. Given the magnitude of the dam and levee safety issues, USACE is developing a new Engineering Manual (EM) titled “Seepage Control Cutoffs for Dams and Levees.” This EM covers all of the methods to construct cutoff walls. USACE has partnered with the Deep Foundation Institute (DFI) in preparation of the EM to ensure that it is comprehensive and draws from the expertise of the specialty foundation engineering companies that design, manufacture, and construct seepage control cutoffs around the world. The EM contains case histories as well as a comprehensive project statistical summary and guide specification paragraphs. The goal of USACE was to make the EM a state of the art document for use by Districts.HISTORYSlurry wall construction techniques were developed in the late 1940’s in Italy by ICOS. The first use of the slurry trench method of construction in the United States was by the USACE Memphis District in September 1945, to form a partial cutoff along the Mississippi River levee on the Arkansas side of the river just below Memphis, Tennessee. The idea for the project probably evolved from the use at that time of puddle clay trench cutoffs combined with the use of drilling mud for advancing borings. A paddle wheel mixing device was constructed for making slurry from native clays. Trenches were dug to a 20-ft depth using a trenching machine and to a 35-ft depth using a dragline with a 100-ft boom and 2-cu-yd bucket. Backfill was mixed in windrows at the site from hauled-in clay gravel and native materials and pushed into the trench by a bulldozer when the length of the trench was equal to about twice the trench depth. It is amazing that after almost 70 years, the technique is still about the same as it was when first developed by the Memphis District. A soilbentonite cutoff was constructed under the Kennewick Levee adjacent to the Columbia River as part of the McNary Dam Project in Washington by the Walla Walla District in 1952 The first application of a soil-bentonite slurry trench cutoff for control of underseepage at a major earth dam was at Wanapum Dam on the Columbia River in Washington in 1959.The first cement- bentonite cutoff in the United States was constructed at the Tilden Tailings Project to store tailings from the Tilden Mine in Michigan in 1976. The first cement-bentonite cutoff constructed at a dam on a river retaining a reservoir in the United States was completed in 1978 at the Elgo Dam (formerly the San Carlos Dam) in Arizona.The USACE has designed and constructed some of the deepest and most complex cutoff walls for dams since the 1970’s. The first major concrete panel cutoff wall constructed in a dam in the United States was at Wolf Creek Dam (Nashville District) by the ICOS Corporation between 1974-77. The dam has a long history of seepage issues associated with the karst geology that comprises the foundation. In 1968, about 17 years after first being impounded, wet areas, muddy flows in the tailrace and sinkholes in the downstream toe adjacent to the switchyard occurred."

Jan 1, 2014

By Stefan Aronsson, K. Rainer Massarsch

"ABSTRACT The geology of Sweden is characterized by the most recent glacial period with deposition of very soft clays and loose sand. Due to these difficult geotechnical conditions, new, innovative foundation and ground improvement methods were developed, which today are used in many other countries. Over centuries, Swedish scientists and engineers have made important contributions to the developments in foundation engineering. An important aspect of the success of Swedish foundation engineering in practice is the spirit of close cooperation between practitioners, engineers, and scientists. This has been achieved by the establishing of commissions, with the aim of finding solution of geotechnical problems. The paper focuses on developments in foundation engineering during the last century and does cover present activities in Sweden.IntroductionSoil mechanics and geotechnical engineering play an important role in Swedish society, as most construction activities require the consideration of foundation conditions. The objective of the paper is to summarize important developments in foundation engineering, primarily during the past century, which have influenced geotechnical engineering also in other countries. These achievements are the result of contributions by scientists, engineers and practitioners, only a few of which can be named. The paper does not claim to cover all aspects of geotechnical engineering, as emphasis is on the solution of foundation engineering problems from an international perspective. Thus, ongoing or recent research and development projects and activities within the geotechnical community are not included, as this would exceed the scope of the paper.Over the centuries, Swedish scientists and engineers contributed to the development of civil and foundation engineering. One important reason is the geology of Sweden, which is characterized by the most recent glacial period, resulting in the deposition of soft clays and loose sands in the coastal areas and dense glacial till in the interior of the country. Geotechnical engineering in Sweden has a long tradition and early contributions by several Swedish engineers and scientists have had a profound influence on the current foundation design in and beyond Sweden. A description of early Swedish geotechnical engineering has been presented in several publications by Flodin and Broms (1981), Broms and Flodin (1988), Massarsch and Fellenius (2012). The historic development of Swedish geotechnical and foundation engineering can be divided into four periods. During the “Early Era”, engineers were active in different sectors of military, civil, and mining engineering. Next, the “Industrial Era” comprised developments during the industrial revolution, when the transportation infrastructure of the country was modernized and extended. During the third period, possibly the “Golden era” of Swedish geotechnical engineering, which started at the end of the 19th century and lasted the following fifty years, geologists, engineers and scientists helped to establish modern geotechnical engineering. But also during the recent past, the “Modern Era”, several important contributions to geotechnical and foundation engineering which originated in Sweden, are used in many countries today."

Jan 1, 2014

"1.0 DESCRIPTIONThis work consists of furnishing all necessary labor, equipment, and materials to install prefabricated vertical (wick) drains in the ground in accordance with the Plans and as specified herein.2.0 REFERENCED CODES AND STANDARDSASTM D4716-08 Standard Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant HeadASTM D4632-08 Standard Test Method for Grab Breaking Load and Elongation of GeotextilesASTM D4533-11 Standard Test Method for Trapezoid Tearing Strength of GeotextilesASTM D4491-99a Standard Test Methods for Water Permeability of Geotextiles by Permittivity (2009)ASTM D4751-04 Standard Test Method for Determining Apparent Opening Size (A.O.S.) of a GeotextileASTM 6918-09 Standard Test Method for Testing Vertical Strip Drains in the Crimped Condition3.0 QUALIFICATIONSThe Contractor shall have successfully completed a minimum of five wick drain installation projects in similar ground conditions, and installed not less than 5,000,000 linear feet (1,525,000 linear m) of wick drain in the past five years. The Contractor shall have a minimum of five continuous years of wick drain installation experience."

Jan 1, 2014

By Rudolph P. Frizzi

"Abstract Pile design for building structures in the United States is typically performed by: 1) investigating and assigning engineering parameters to the respective ground bearing materials, 2) calculating ultimate pile to ground (geotechnical) capacity which is then reduced by a Safety Factor deemed appropriate by a registered Design Professional thereby arriving at an allowable pile geotechnical pile capacity, and 3) determining the required pile structural section using allowable pile section material properties. It is advantageous to use a Working Stress Design Method (WSDM) approach as one system of loads (service loads) are used in both the geotechnical and structural evaluation. There are a variety of methods used to determine the ultimate and allowable geotechnical capacity, and Building Codes often require a registered Design Professional to determine the appropriate method(s) and capacities. The International Building Code is the Code typically referenced in building design and construction in the United States. Structural design usually follows Building Code requirements and Allowable Stress Design (ASD) procedures. As design of the overlying structure typically follows a Strength Design Method (SDM) approach using factored loads, in some cases piling is first designed for pile-to-soil interaction using service loads, followed by evaluating the pile geometry for factored loads. Construction is the finalization and implementation of the designed piling. As such, project-specific technical specifications are typically developed by a registered Design Professional such that a project Owner can bid, buy, and instruct a Contractor as to the desired piling work and acceptance criteria. There are several Industry groups, including DFI, PDCA, ADSC, and ACI that provide guidance documents which the registered Design Professional can refer to in developing the piling technical specifications. It is the author’s opinion that the registered Design Professional is best suited to observe and verify the piling installation; many Building Departments require verification and documentation by a registered Professional as a condition of final acceptance.INTRODUCTIONPile design for building structures consists of: investigation, design, specification, and verification. In major metropolitan areas within the United States, Building Codes typically identify minimum requirements for each of the above steps. The International Building Code (ICC, 2012) is the Code typically referenced in building design and construction in the United States. Recognizing the ground conditions as well as piling construction means and methods can vary on a site-by-site basis, latitude is given to the registered Design Professional and Contractor to optimize the piling system for the respective project conditions. Field testing and quality control / assurance measures are typically implemented to verify the design intent is attained for the production pile elements."

Jan 1, 2014

By Mario Terceros H., Bengt H. Fellenius

"ABSTRACTFour strain-gage instrumented bored piles were constructed in a sedimentary, dense to very dense, fine to medium sand in Santa Cruz, Bolivia. Two of the test piles were the normally used bored pile constructed with bentonite slurry and two piles were Bauer Full Displacement Pile (FDP). One of each pair was equipped with the Expander Body, an inflatable steel cylinder that on pressure-grouting provides an enlarged pile toe. Head-down static loading test were performed on three of the piles and a bidirectional test was performed on the fourth pile, a standard pile with Expander Body and a bidirectional cell placed immediately above the EB. The latter pile was tested in 3 phases. First by activating the cell, second, by a head-down test, and, third, by a repeat bidirectional cell test. The static loading tests proved the shaft resistance of the FDP pile to be about twice that of the standard bored pile and that the Expander Body more than doubled the toe stiffness. The strain-gage records showed that the standard bored piles had multiple bulges and neckings, which affected the evaluation of the axial stiffness and load distribution of the piles. The testing programme was used for a prediction event with 60 persons, ahead of the tests, submitting predictions of the load-movement curves for the test piles and also a capacity appraised from the curves.1. INTRODUCTIONOn April 23 - 26, 2013, the First International Conference and Seminar on Deep Foundations was held in Santa Cruz, Bolivia under the auspices of INCOTEC SRL, the UAGRM University, and the Bolivian Association of Civil Engineers and Chamber of Construction. To coincide with the conference, a research study on construction and static and dynamic testing of four instrumented bored piles was undertaken. To ""add spice"" to the conference, a prediction event was organized on the test programme. This paper presents the soil conditions at the site, the type and construction of the test piles, the outcome of the prediction event, and the results of the static tests.2. SOIL CONDITIONSGeotechnical studies comprising SPT and CPT tests with routine laboratory analysis were performed on recovered soil samples. Three SPT boreholes were put down at three of the locations of Pile TP1, TP2, and TP3, at 5.0 m distance from each other. The SPT procedure consisted of manual hoisting of the weight by three crew members pulling on ropes over a pulley supported by a tripod and letting the weight fall by gravity. The groundwater table lies at 3.5 m depth.Figure 1 shows diagrams of the SPT N-indices and the distribution of water content in the three boreholes. The SPT-indices show the soil density to be compact. The average water content is about 15 %, plus-minus a few percent."

Jan 1, 2014

By Sachihiko Tokunaga, Hirofumi Taguchi, Kenji Maruyama, Hidenori Takahashi, Yoshiyuki Morikawa

"Abstract The present study proposed a new liquefaction countermeasure to improve sandy ground and conducted a trial execution. The new method is a floating-type and lattice-shaped cement treatment method, where cement-treated soil is not fixed to a non-liquefiable stratum. A fixed structure such as treated soil should be formed at the side of the floating-type treated soil to reduce its lateral displacement. In the study, one-dimensional dynamic response analyses were first conducted to confirm the mechanism of the new method. Then, a series of centrifuge model tests were performed to demonstrate the effect under a stress condition at the prototype scale. The analyses and model tests confirmed the effect of the liquefaction countermeasure. Finally, trial executions were carried out to confirm high-quality vertical execution.INTRODUCTIONLiquefaction induced by an earthquake generates sand boiling and ground settlement. Other problems have also been reported, including a decrease in bearing capacity and an increase in the horizontal earth pressure against retaining walls. To prevent these problems caused by liquefaction of the ground, various countermeasures have been proposed, such as cement deep mixing and high-pressure jet mixing methods. These methods have the big advantage of being applicable to ground that contains soil with a fine-grain fraction. Furthermore, the unnecessary displacement caused by the construction can be reduced. In Japan, a lattice-shaped cement-treatment method has frequently been used at many construction sites to prevent liquefaction, where cement-treated piles are intersected to form a lattice, as shown in Fig. 1. The lattice-shaped walls can reduce the shear stress generated by an earthquake, restricting the liquefaction at that location. However, the construction cost of the cement treatment is relatively high compared to other methods such as the sand compaction pile (SCP) method, and needs to be reduced. In particular, the cost of the high-pressure jet mixing method, which can be applied to the liquefiable ground under existing structures, is significantly high. Therefore, decreasing the total volume of the cement treatment is necessary to reduce the construction cost."

Jan 1, 2014

By M. Hesham El Naggar, Yasser Abdelghany

"ABSTRACT: The axial and lateral monotonic and cyclic behavior of helical pile foundations was investigated and new innovative helical screw systems suitable for seismic loadings were developed and patented. More than one hundred full scale field load tests were conducted on instrumented helical screw piles installed in cohesive soil. The piles included: plain helical screw piles (P-HSP); grouted (G-HSPs); fiber reinforced polymer FRP-G-HSPs; and reinforced grouted RG-HSPs. The RG-HSP piles axial capacity was more than twice that for P-HSP, with minimal reduction after cyclic loading, and their lateral capacity was more than 3 times the P-HSPs capacity. A 3-D finite element model was established. The results of 3-D finite element modeling were used to establish the load transfer mechanism and a design methodology for the considered piles.INTRODUCTION AND LITERATURE REVIEWHelical (screw) anchors have been utilized in tension loading and have gained popularity for bearing load applications. Helical piles represent an overall cost effective alternative to conventional piles for new construction and repair applications. The helical piles speed and ease of installation, less noise during installation added advantage with regards to their efficiency and reliability for underpinning including re-support and reconstruction of distressed and damaged foundations for either stabilization or rehabilitation. The “square shaft” SS175 pile is a segmented deep foundation system with helical steel bearing plates (helices) welded to a central steel shaft. Load is transferred from the shaft to the surrounding soil through these bearing plates. Segments or sections are joined with bolted couplings. Practically installed depth is limited only by soil resistance and economics. A helical bearing plate or helix is one pitch of a screw thread. All helices regardless of their diameter have a standard 75 mm pitch (Figure.1). The performance of single helical anchors and group action were studied experimentally and theoretically by several researchers, the researches focuses on the installation torque and uplift resistance. Some researches focus on the load carrying capacity with little pile response to cyclic loading effects or to instrumented full scale field testing. Helical piles axial compressive or lateral loading still is not well characterized and needs more analyses and their seismic performance was not investigated. For such this research was initiated to investigate the helical piles monotonic and cyclic performances under axial and lateral loadings to consider their usage in different applications in seismic zones. Among the several researchers, Clemence (1983); Mooney et al. (1985) conducted field and laboratory testing; Hoyt (1989), Hoyt et al. (1995), and Ghaly and Clemence (1998) conducted theoretical and experimental testing, Puri and Vijay (1984), Huang et al. (1995), Perko (2000), and Pack (2000) conducted theoretical analyses. Rao and Prasad (1993), Prasad and Rao (1994), conducted experimental testing; Vickars and Clemence (2000) studied the performance of helical piles with grouted shafts."

Jan 1, 2014

By Carnevale Francesco, Bracci Laudiero Alberto, Pampanin Piero

"SummaryIn the Port of Naples a slurry wall has been realized through a sandy layer up to a deep tuff layer using the Cutting Soil Mixing technique.The executed panels have dimensions of 2.8 m x0.65 m in plan and a total length of 25 m. Primary and secondary panels have been executed using the wet to wet technique. During the panels execution the following parameters had been measured: injection pressure, injected volume, verticality. At the end of the works an exploratory campaign has been carried out through boreholes collecting samples for laboratory tests in order to verify the diaphragm thickness and its physical and mechanical properties (i.e. unit weight, unconfined compressive strength).The interpretation of the collected data allowed to verify the efficiency of the method, the volume of slurry loss due to permeation during the panels execution, the quantity of the obtained spoil compared to the volume balance equation, both for the sand and the tuff layer.Eventually, the measured physical and mechanical characteristics of the panels have been correlated to the execution method performed.IntroductionIn the Naples Port area there is a polluted site which has to be hydraulically isolated in order to prevent the pollution of the groundwater that flows from land to the sea through the Port area. A hydraulic cut-off wall has to be realized and particularly a slurry-wall realized using the CSM method had been executed.To date, two stretches have been executed, 140 an 110 m in length respectively, as shown in Figure 1 and Figure 2.After execution, the slurry-walls have been investigated with boreholes. In-situ and laboratory tests on the recovered samples of grout have been carried out; furthermore, the geotechnical parameters of the mix composing the wall have been measured."

Jan 1, 2014

By W. Sondermann

"AbstractThe construction of a distribution centre of minerals for a global mining and resources cooperation demanded the control of deformations and displacement of the stack reclaimer facilities on very inhomogeneous subsoil conditions. The variation of quality from soft clay with CPT values below 1 MPa up to rock formations were the challenge in design and execution of all the foundation works.The advanced design considerations were resulting in a barrier wall system to limit the deformations of the up to 40 m deep bored pile of the stacker-reclaimers, whereas the layout of the barrier wall and the stiffness of the elements had a major impact on the residual lateral forces to be absorbed by the bearing structure.IntroductionA large international raw material distribution organisation is currently building an iron ore and pellet distribution centre on the north-western coast of Malaysia. The distribution centre will handle around 90 MTPA (million tons per annum) of iron ore and includes accompanying plants for loading and unloading iron ore and pellets, pelletizing plants as well as corresponding storage space for these raw materials. The total storage space extends about 800m north to south respectively 1400m east to west and is about 200m from the coastline. The project area is located in a wide valley basin, bounded by a range of hills to the north. The existence of soil with low bearing capability in the area designated for the plant meant that measurements for ground improvement were required in the storage areas, in order to combine the needs of iron ore and pellet storage areas with requirements of the loading facilities as the overall project demand.Project LayoutThe iron ore distribution centre and the pelletizing facility both consist of an import/export jetty, material handling facilities, pellet plant and the associated infrastructure. This publication describes the execution of ground improvement and foundation works for the loading and storage system, which consists of five rows of stockpiles and four intermediate rows of stacker-reclaimers. The total area of these systems comprises 278,881 m2 (Fig. 1)."

Jan 1, 2014

By Frank Haehnig, Kjell-Åke Averstad, Johannes Glückert

"AbstractThe Söderströmstunneln is part of the Citybanan project that is currently under construction in the centre of Stockholm. Main part of the lot Söderströmstunneln is a 300m long immersed tunnel connecting the inner-city islands Södermalm and Riddarholmen. It consists of three tunnel elements that have been immersed in summer 2013. Since the solid bedrock is descending in that area to more then 40m depth, the tunnel elements have been placed and are permanently supported on four pile groups that have been constructed in advance. The common Swedish system of steel core piles has been used to built the pile groups. Drilling and installation of the steel cores piles in free water depth of up to 20m had to be done from a pontoon. The steel core piles are connected with underwater concrete pile caps.IntroductionCitybanan is a new 6km long double track railway tunnel running beneath central Stockholm including two new underground stations Odenplan and Stockholm City. When completed in 2017 commuter trains will have their own tracks through Stockholm, whereas the remaining railway traffic will continue to use the exisiting two tracks (see Fig. 1). This will double the capacity of the railway traffic through Stockholm. The Swedish transport administration Trafikverket is the client for this project. The design and built contract is carried out by the German contractor Züblin Spezialtiefbau GmbH together with their Swedish subsidiary Züblin Scandinavia AS.As the new Citybanan tunnel is in large parts situated below the bedrock level, it can be executed as rocktunnel in the common drill and blast method. Between the two inner-city islands Södermalm and Riddarholmen the tunnel is crossing the Söderström, an arm of the lake Mälaren. Here the bedrock is descending to a deep valley with more then 40m depth. To connect the rock tunnels between these islands a 300m long immersed concrete tunnel supported on pile foundations is currently under construction."

Jan 1, 2014

By Trevor L. L. Orr

"AbstractThe background to the harmonization of geotechnical standards that has taken place in recent years in Europe has been the move to more economic and political integration following World War II that has led to the formation of the European Union. Prior to 2010 the standards used in the European countries for geotechnical design, investigation and testing and for the carrying out geotechnical work, such as the installation of piles, were the different national standards, which were not harmonized. The harmonization of geotechnical standards in Europe started in 1981 with work on a model Eurocode 7 for geotechnical design that led eventually to publication by CEN, the European Committee for Standardization, of the European Standard version of Eurocode 7 in 2004. In parallel with the work on Eurocode 7, a large number of associated harmonized standards have been, and are being, prepared by CEN and by the International Standards Organization (ISO) for geotechnical investigation and testing and for the execution of geotechnical works. Standards published by CEN must be adopted by the CEN member countries and all conflicting standards withdrawn. Hence all the CEN countries have adopted the same the harmonized text of Eurocode 7, but with National Annexes that allow national choice with regard to Design Approach and partial factor values. The adoption of Eurocode 7 and its associated geotechnical standards has removed the barriers to geotechnical activity in Europe due to the presence of different national standards. It has also enhanced the ability of EU firms to compete in the global market.Background to harmonization of geotechnical standards in EuropeThe initial moves towards the harmonization of geotechnical standards in Europe can be related to the economic and political developments that took place in the period immediately following World War II to revive the economies of Western Europe. Europe at that time was divided by a political and, in many places, a physical barrier, known as the Iron Curtain, into two very different and separate zones: communist in the east and non-communist in the west. In 1952 the European Coal and Steel Community (ECSC) was formed, linking 6 countries: Belgium, West Germany, France, Italy, Luxembourg and the Netherlands, and establishing a common market in coal and steel. The ECSC was the first international organization to be established on the basis of supranational principles whereby negotiated power is delegated to an authority by the governments of the member states. In 1957 the ECSC became the European Economic Community (EEC), also known as the Common Market in the English-speaking world, with the aim to bring about economic integration. With the addition of Denmark, Ireland and the UK in 1973 and Greece in 1981, followed by Portugal and Spain in 1986, this led to the formation of the European Union (EU) in 1993. East and West Germany were reunified in 1990, following the fall of the Iron Curtain in 1989. In 1995, Austria, Finland and Sweden joined the EU, and since then the numbers of countries in the EU has increased to 28, many of which are countries that were formerly behind the Iron Curtain."

Jan 1, 2014

By Maurizio Siepi, Stefano Trevisani, Pagliaccim Federico, Daniele Vanni

"Abstract: The paper describes a large innovative project completed in 2012-20123 by Trevi Group, to develop equipment capable to install ultra-deep diaphragm wall. The project highlights the capacity of SOILMEC to design and build a new hydromill able to reach an unprecedented depth of 250 m, including new devices for monitoring and correct the verticality. The entire project can take advantage of the long and solid experience matured by Trevi and Rodio (now part of Trevi Group), developing in house or, else, select the elements necessary for a high quality product in the ground.The paper describes the results of different systems used to monitor and control the verticality and the twist of panel during excavation, together with the method used to pour concrete. Finally, the results of verification coring and lab tests on concrete samples recovered at various depths are discussed. The test field has been supervised by representatives of three of the major Italian Universities, and lasts almost one year from August 2012 to June 2013.The verification holes made use of an innovative combination of directional drilling and coring, to check the quality of the plastic concrete for the full length of the panel. The data confirmed that the test panel has high quality concrete, meeting or exceeding to the prefixed requirements.With this test, super-deep cut-off walls reaching depths of 250 m have become a reality. This would change the perspectives of dam engineering both for existing dams rehabilitation and for new dams design and construction. With the execution of this test panel, the technology of milled concrete cutoffs has made a ”quantum leap”, pushing the limit of practicable dams."

Jan 1, 2014

By J. Stacho, Frankovská. J.

"Abstract The use of continuous flight auger (CFA) piles in Slovakia has increased significantly in recent decades. High-rise building of administrative centre Lakeside Park in Bratislava is based on piled-raft foundation. The technology of CFA has been used due to the advantages of this technology in comparison with driven and bored piles in local geotechnical conditions. Piles have been designed in accordance with Eurocode 7. Resistance of piles was calculated by using an analytical calculation model for bored piles according to Slovak technical standard and CFA technology has been taken into account by coefficient equal to 1.1. Settlement of piles was calculated by using a calculation model which is being used in Czech Republic and Slovakia. Two well instrumented static load tests were carried out to verify the pile design. The results of static load tests showed that the design was conservative. The paper presents analysis of numerical modelling of CFA pile and static load tests. Load-settlement curves and load distribution curves over pile shafts are compared. Software Plaxis 2011 has been used for numerical modelling. Hardening soil model allows considering over consolidation of Tertiary Silts and water pressure in deep sandy lenses. The article also presents the parametric study where the influences of pile-soil interface reduction factor, over consolidation ratio and material models of soils are analysed. The results of numerical modelling showed that the most appropriate results have been obtained when the interface reduction factor equal 0.9 and real behaviour of groundwater were considered. The conclusion of the paper confirms that mechanical behaviour of the ground can be better understood and determined by using FEM than analytical methods.1. IntroductionPiles are among the most frequently used elements of deep foundations. Piles transfer loads down to a suitable bearing stratum when the soil immediately below a construction is unsuitable. Piles are also used to reduce settlement of structure. At present, the requirements of limit settlement of structures are more stringent. Examples of these structures are commercial and administrative centres that form a complex of different tall buildings. High-rise buildings cause greater contact stresses than connected low-rise buildings. Pile foundations in such cases should be placed under the high-rise buildings to achieve an appropriate settlement.Resistance of piles can be determined from static load test results, in-situ tests and empirical experiences or calculations. Static load tests give the most reliable results, but these tests are also the most expensive. This is the reason for constant development of computational methods. Especially numerical methods give more accurate results by using more sophisticated material models e. g. hardening soil or hypoplastic model."

Jan 1, 2014