Search Documents

By Graeme Smart, Thomas Fiala

"Yorkville Plaza II, a 40-storey signature condominium residence, is scheduled to open on Avenue Road in Toronto’s prestigious Bloor-Yorkville neighbourhood in spring 2017. In close proximity to Toronto’s subway system, the new tower requires six levels of underground parking, founded in wet, silty sand.Isherwood Geostructural Engineers (Isherwood) was retained in April 2012 by developer Camrost-Felcorp to provide a shoring and excavation solution to address the challenging site conditions. A 31-storey upscale residential building under renovation with three levels of parking, owned by Camrost-Felcorp, flanks the site on the north. Situated on the eastern border is a 7-storey building with three levels of parking. Avenue Road, a four-lane arterial road that brings heavy commuter traffic into downtown Toronto, runs along the western border, and on the southern border of the site is a busy City road that brings traffic into the popular Yorkville area. The tunnel for the Toronto Transit Commission’s (TTC) overburdened east-west subway is located 14.5 m to the south, running below an existing 26-storey neighbouring building. Electrical and communication utilities (Bell) are closely located along the southern side. Non-documented existing excavation shoring, installed in the early 1970s, on the southern and western sides compounded the difficulties presented by the TTC tunnel.This paper presents the unique, non-conventional hybrid shoring solutions Isherwood developed to address the challenges presented by the site, as well as other complications that surfaced during the project: non-encroachment requirements (no tiebacks) beneath uncooperative neighbours, tight geometry to install shoring, and Toronto’s two coldest winters in decades.THE PROJECTBecause of circumstances associated with this site, for this project Isherwood designed two unique shoring walls which drew on their experience and expertise they had gained over the last 40 years. The following is the story of this site:Yorkville is an affluent neighbourhood in the heart of Toronto with a vibrant mix of high-rise towers, residential homes, tony restaurants and flagship shops. The development requires six levels of underground parking (a 20m deep excavation), with three levels undermining the high-rise buildings to the north and east and extending into wet, silty sand.Isherwood was retained in the spring of 2012 to design the excavation shoring. Isherwood’s scope also included field support, design, verification and monitoring. Finite Element Analysis was employed to confirm Isherwood’s design and anticipated movement of the south shoring wall and the TTC subway tunnel.The existing site was severed in two, with the proposed condominium tower slated for the southern portion. On the north half of the site stands a 31-storey building (Yorkville Plaza I at 21 Avenue Road), with three levels of underground parking, sitting on belled caissons which were one foot from the back of the proposed shoring wall so this would have to be considered in relation to the design and drilling methods. Constructed in the early 1970s, Yorkville Plaza I is currently being converted from the Four Seasons hotel to luxury condominiums by Camrost-Felcorp. To the east, directly adjacent to the proposed shoring, stands a 7-storey building (164 Cumberland Road) with three levels of parking, supported on spread footings founded on stiff clayey silt. The tunnel for the TTC’s busy east-west subway, a double box structure built by cut-and-cover in the 1960s, is located 14.5 m to the south, 9 m below grade, and running below an existing 26-storey building. Bell fibre optic communication cables and electrical lines, along with storm and sanitary sewers, are situated on the south and west sides of the site, leaving limited room to install shoring. Due to the heavy volume of commuter traffic on the four-lane arterial road (Avenue Road) to the west, site access and lane closure were not permitted here."

Jan 1, 2015

By E. W. Raabe

The paper discusses the increasing role of specialist grouting techniques to form water seals or cut-offs for deep basement construction. Raabe and Toth discuss the various grouting methods available for sealing applications and then concentrate on the use of Soilcrete Jet Grouting, a system particularly well suited to ground water control. The Soilcrete processes, suitable soil types and quality control methods are fully described, particularly with regard to the formation of cut-off walls and sealing slabs to prevent the progress of ground water or leachates. The authors have included case histories detailing their experience on designing and installing Soilcrete seals for various projects in West Germany. These include an underground rail project in Dortmund and a discharge structure for the Alz Canal at Burghausen.

Jan 1, 1989

By Andrew Pontecorvo, Steven Lowe, David Sposito

Buildings with large height-to-width ratios require foundations with significant uplift resistance. This paper presents a case study of the permanent rock tiedowns installed for One Manhattan West, a sixty-seven-story office building in midtown Manhattan. Site access and schedule dictated the size of the equipment for installing the tiedowns would be limited to drilling a 16 inch (406 mm) diameter hole. A three bar configuration of 3 inch (76 mm) diameter high strength threaded bars was chosen to develop an allowable capacity of 923 tons (4060 kN) per tiedown. Although the quality of the rock at the site was generally high, a challenging geologic condition emerged during the installation of one of the tiedowns requiring a creative installation procedure. Although the three bar configuration performed relatively well there are challenges with loading and testing this bar arrangement. Unlike single bar tiedowns that are typically tested with a high success rate, testing of a multiple bar system can result in some unsatisfactory results. This may be attributed to the installation challenges, difficulty loading each bar uniformly and/or the method of monitoring the test. Understanding the complexities is necessary to improve the testing results and achieve similar reliabilities of single bar systems.

By Abhijit Saha

"The stone columns improve the performance of foundations on soft and loose soil due to the ability of composite ground to sustain increased structural loads under reduced settlements. The interaction between the two basic elements: the ambient subsoil and installed column, present a complexity of behaviour, both in terms of applied stresses and resulting strains. Moreover, as the same is provided in-group in a regular array beneath foundations, the performance of an individual column is likely to be influenced by the presence of neighbouring columns. The present paper addresses this very issue. Analysis of reported field hydro-test data of large diameter oil storage tanks in soft ground in reference to some existing theories led to the development of the stone-column ‘group efficiency factor’. In order that such factor is of general use, it was felt necessary to examine the applicability of the factor to different sizes of groups under varied subsoil conditions. With this in view, some model test results reported in literature of single and group of columns have been analysed and in the process an explicit relationship regarding the stone-column ‘groupeffect’ could be established.INTRODUCTIONThe field application of the stone column technology has gained momentum than the intricate design methodology due to its simplicity in installation and intuitive performance. The ground improvement is due to the complex interaction within the ‘unit-cell’ comprised of the installed column in ambient ground under sustained vertical stress; in association with the interdependence of problem geometry and material properties of the two different soils-one 'native' and the other 'back-filled'. The beneficial effects are increased load capacity, reduction in total and differential settlements, minimization of post construction settlements effected by accelerating consolidation, reduced risk of soil liquefaction, aiding in improvement of slope stability of embankments and natural slopes and effecting changes in the dynamic response. The ‘unit-cell’ concept of a tributary soil cylinder encapsulating an installed column with some reasonable assumptions and boundary conditions (Aboshi et al, 1979; Balaam & Booker, 1981; Van Impe & De Beer, 1983; Priebe, 1976; Saha & De, 1994; Saha; 2005, 2006, 2007, 2011, Saha & Das; 2007) deals with the load-settlement behaviour of the composite system. The present investigation is based on published field data from literature & validated with experimental study reported in literature. The study addresses the effect of group interaction of stone columns beneath a large area loading on ground settlement. The hydrotest load-settlement data of 12 large diameter oil storage tanks founded on stone column reinforced soil at Haldia1 and Kandla2 refinery sites in India; reported by Som (1997), has been analysed to quantify the group efficiency. The results as obtained are compared with experimental study on 2, 3 and 4 stone column groups at different spacing-diameter ratios in soft clay3 reported by Rao et al (1997) to validate the above analysis. A unique relationship between the column spacing and group efficiency has been obtained."

Jan 1, 2015

By David R. Shields, Michael T. Bracher

"The $330 million (U.S.) Dana-Farber Cancer Institute’s Yawkey Center for Cancer Care (Yawkey Center) sits in the heart of Boston’s Longwood Medical Area. The Yawkey Center is a cutting-edge cancer care facility that houses Dana-Farber’s adult clinical care and clinical research programs. Standing 14 stories above grade, it includes 7 stories of underground parking extending 75 ft (23 m) below ground. The structure is on a 198 by 186 ft (60 by 57 m) site sandwiched between Dana-Farber’s 13-story Richard A. and Susan F. Smith Research Laboratories Building, the Medical Area Total Energy Plant (MATEP), Jimmy Fund Way, and Brookline Avenue, a busy four lane artery through the heart of the Longwood Medical Area. Together with Simon Design Engineering, the project structural engineer, GEI Consultants designed an innovative foundation and excavation support system to isolate the building from ground vibrations generated by the adjacent MATEP power plant. In effect, the Yawkey Center is a 21-story free-standing structure that starts 7 stories below grade.The MATEP facility provides power for 9 million sq ft (840,000 sq m) of occupied space in the medical area. There are six 32-cylinder diesel engine generators in the facility that produce low-frequency ground vibrations in the 10 Hz range, similar to the natural frequency of typical building elements. The resonant response of the Yawkey Center building structure to these ground vibrations would affect the performance of sensitive medical research equipment and cause an unacceptable environment for clinical care.The soil profile at the site consists of stiff clay, fine sand, glacial till, and bedrock consisting of hard metamorphosed conglomerate. In-situ measurements of ground vibrations performed in boreholes showed that there was little attenuation of the vibrations with depth in the soil layers overlying the bedrock, but the vibration amplitude in the bedrock was markedly lower than in the overlying soil. Based on this data, an innovative foundation system was designed to support the building on bedrock located up to 110 ft (34 m) below ground surface, while isolating it from the surrounding soil. This was done by physically separating the below-grade parking garage floors from the perimeter foundation walls to create a free-standing structure supported on the bedrock"

Jan 1, 2012

By Karen Dawson

Pressure-grouted helical piles support a new seven-story homeless housing center in the Coney Island neighborhood of Brooklyn, New York. The project team instrumented and statically load tested piles to as much as 1,000 kips (4.4 MN) in advance of construction to obtain the approval of the New York City Building Code officials and to verify the design. Use of pressure-grouted helical piles required additional design effort and time risk because of New York City's Construction Code Determination (CCD1) process, which is required for non- standard deep foundation types. Despite

May 1, 2022

By Susan Rafalko, Mike Walker, John Sankey, Sherif Aziz, Alex Potter-Weight, Mary Nodine, Frederic Masse

"After several successful projects on the Garden State Parkway and New Jersey Turnpike for support of single-stage MSE (Mechanically Stabilized Earth) walls using rigid inclusions (Controlled Modulus Columns) as an alternate to two-stage MSE walls and surcharge, the Bass River Bridge Widening project presented additional challenges in terms of soil conditions and height of embankment that created opportunities for the design-build ground improvement contractor and its MSE wall-designing partner to enhance their design and construction methods. The specialist contractor decided, in association with the wall system supplier, to perform an independent large scale instrumented test area on the project to demonstrate the ability of the design techniques to model the behavior of the system, as well as the capacity of the rigid inclusions to provide the necessary bearing capacity and settlement control to allow the construction of the highway without any consolidation period. This paper presents a detailed description of the design of the ground improvement system and MSE wall system, as well as the results and conclusions of the monitoring data gathered on the large scale test program. The combination of rigid inclusion ground improvement technologies, such as the CMC system, together with an MSE wall system allows for the rapid and economical construction of high embankment without waiting for a surcharge and consolidation period or the necessity to use a two-stage wall system. In-depth understanding of the design techniques and advantages of this combination will be provided and should be beneficial for any geotechnical engineer or owner looking for innovative solutions to save both time and cost on their projects.1. IntroductionAs development continues on sites with poor ground conditions throughout the world, conventional MSE walls remain a flexible design solution; however, construction of MSE walls in combination with ground improvement is becoming more frequent where extreme differential and/or total settlement prevail due to soft ground conditions. Various techniques have been used in the past in such conditions (e.g. conventional surcharge, staged construction, or two-stage MSE walls), even though these design solutions have typically involved longer waiting times for settlement to occur. As a result, conventional MSE wall design has been combined with a variety of ground improvement techniques consisting of rigid inclusions for an economical and efficient solution with the potential to accelerate construction and limit long term settlement. For the particular subject of this paper, the specialist contractor (Menard) proposed to use CMCs (Controlled Modulus Columns) to support the highest part of the MSE wall. CMCs are grouted displacement rigid inclusions installed in a grid-like pattern using a displacement auger. Before the CMCs are installed, a working platform may first need to be placed to allow equipment to move around the site depending on the ground conditions. Following the CMC ground improvement, an LTP (Load Transfer Platform) is installed prior to the construction of the MSE wall."

Jan 1, 2015

By Stephan Fisch, Franz-Werner Gerressen

"The use of cut-off-walls (COW) for the open pit coal mines has been used for decades. They have been used to reduce the negative hydraulic impact to the surrounding area caused by the open pit mining. The pile-guided trench cutting system is a worldwide unique technique, originally developed by the engineers of the mining companies themselves. It guarantees a continuous, joint free, COW during a continuous installation process. At this specific site in Welzow, this technique has been pushed to new limits in order to address the local lake region. Depth capability has been designed to about 430 ft (130m), proven are already depth of about 360 ft (110m) at a constant trench width of 39 inch (1000 mm). This project is approximately. 6.8 miles (11 km) long of COW, scheduled to be completed in 12 years period. About 2.05 miles (3.3km) have been installed, which is equivalent of about 3.5 Million ft² (330,000 m²). The system flushes special clay which forms a filter crust at the inner surface of the trench. Only natural clay resources used, in order to achieve the cut-off effect (colmation effect). The paper explains the installation process of the cut-off-wall as well as the equipment systems developed specifically for this project. After a successful start of the first phase of the project, the next step in the advancement of the equipment is already underway to enable the installation of greater depth to approximately 490 ft (150 m +) and beyond. The next generation equipment system is scheduled to start operation around 2018 INTRODUCTIONThis Serbian saying “Bóh je stworil Lužicu a cert je zaryl brunicu – God created Lusatia and the devil buried brown coal underneath it.” captures local communities’ ambivalence towards lignite.Lusatia is an almost entirely flat stretch of land between the Elbe and Neiße rivers dominated by glacial sands. On the surface, the heathland and woodland is hardly noteworthy. However, three large lignite mining regions, two in Brandenburg and one in Saxony, in the east part of Germany, divert the attention to underground level, down to depths of up to 120 meters. Here, seams crisscross the earth like ribbons. They were formed in the Tertiary around 17 million years ago.The mining of the lignite started almost 200 years ago. To enable open pit mining, a suitable dewatering system was required. At first, wells and drainage system were used. With the increasing demand to go deeper to enable full use of the existing resources with greater mining depth, a decision taken back in the 60th of the last century, the amount of water which had to be pumped increased dramatically. In peak times, approx. 1.57 Billion cubic yards per year (1.2 Billion m³/year) had to be pumped. This led to a lowering of the groundwater level for up to 230 ft (70 m), impacting the regional lake landscape. In order to reduce the influence on the water balance, and bring the water level back to pre1970th, a first development took place to implement the use of specific COW system to depth of about 147 ft (45m)."

Jan 1, 2017

By Tai Luu, Michael McNicholas, James C. McIntyre

The Jersey City Municipal Utilities Authority (JCMUA), discovered that an existing sewer pipe had collapsed under the New Jersey Transit Conrail Railroad between Pine Street and Ash Street in Jersey City New Jersey. Immediate action was taken to abandon the pipe in place and install a new sanitary sewer. The borings showed 10-20 ft (3.04 m.- 6.09 m) of competent fill overlaying approximately 8 ft. (2.44 m.) of compressible peat and organics. Groundwater was at 8 ft (2.44 m) below ground level. The poor condition of the soils at subgrade could not withstand the extreme weight of the jacking machine or the thrust force required to push the casing from the launching pit to receiving pit. The support of excavation (SOE) would therefore not only need to retain the soil to allow the jacking equipment to reach subgrade at 14 ft (4.27m) below working grade, but also the back wall of the SOE would need to be sufficiently robust to function as the reaction block for jacking operations. The alignment and allowable tolerance for the jacked casing was minimal, therefore the performance of the SOE was extremely critical to the success of jacking operations. This paper will discuss in detail the design concepts that were developed and implemented by the team to overcome these obstacles. HISTORY The discovery of a collapsed section of an existing sanitary sewer led the Jersey City Municipal Utilities Authority to act on an emergency contract. The project design team was tasked with developing an abandonment plan for the broken pipe and installation of the new pipe through challenging geology. The new 180 ft.(54.96 m) long, 54-in. (1.37 m) . diameter sewer pipe was designed to be contained within a 72-in. (1.83 m) protective steel casing. The installation of the new sewer pipe would require a detailed understanding of the geology. The geotechnical subcontractor assembled a subsurface investigation report on November 2nd, 2017. It was quickly realized that the only way to replace the pipe was with a jacked pipe system since the large grade change and the Conrail Right of Way created no other alternative. Delaying or closing the railway was absolutely not an option as that particular railway served as the main heavy-haul route to and from Jersey City. It became apparent that a major obstacle to pipe jacking was the challenging geology present across and beneath the proposed sanitary sewer. The following challenges faced the design team prior to the installation of the replacement pipe:

Jan 1, 2019

By Dario Libano

"The Line 5 Extension, in Sao Paulo, Brazil, is currently the most important investment in public transportation by Sao Paulo’s state government. It will connect the south part of the city to the city center, crossing through four other major Metro lines and stations; all currently in operation. The total extension of the line is 11 km (6.8 mi), and includes a new parking yard for the trains and 11 new stations. The Brooklin Station, one of the new stations due to be open and operating in 2016, has a unique geometry of five secant shafts.The original design included constructing five secant shafts stabilized by two plastic slurry walls using conventional grab technology. One slurry wall, along the Santo Amaro Avenue, was to contain the contamination plumes, and another was for temporary support to enable the excavation of the shafts. The final retaining wall design was changed to a concrete structural diaphragm wall that reduced the construction time of the shafts by half, allowing the contractor to meet the construction schedule. This solution also avoided dewatering effects in a geological region characterized by Quaternary sediments and environmental contamination plumes. It was the first time that a hydromill was used in such a situation in Brazil. The hydromill, by overcutting the panels, increased the quality of the joints, and decreased the probability of having seepage into the shafts. The hydromill also created a seepage barrier and avoided movement of the contaminated plumes.The GeologyLocal geology is composed of a superficial Quaternary soil, basically soft organic clays and sands and gravels. From the depth of 8 m (26 ft) until 18 m (59 ft), geology is composed by tertiary medium compact sand with thin silt-clay layers. From 18 m (59 ft) down, there are alternations between compact silt-sands layers with very hard clays layers. Each is approximately 5 to 10 m (16.4 ft to 33 ft) thick.The Initial Basic DesignThe original basic design of the Brooklin Station was to be constructed from five 40 m (131 ft) diameter intersecting circular shafts, all in a line along the axis of the Metro tunnel, in 555 days. In the excavation sequence, the odd shafts were first excavated, waterproofed and had part of their inside cast-in-place structure built before the even shafts were excavated. During the excavation of the even shafts, part of the odd shaft’s support was demolished and connected with the even support. A 0.8 m (2.6 ft) thick plastic slurry wall, acting together with the wire mesh reinforced shotcrete support, ensured the excavation stability around the five shafts."

Jan 1, 2014

By Filippo Leoni, Wesley Schmutzler

"The LPV-111 East Back Levee Improvement Project lies along the Gulf Intracoastal Waterway (GIWW) in Orleans Parish of New Orleans, La., and is an essential component of the New Orleans Hurricane Protection System. The Hurricane Protection Office of the U.S. Army Corps of Engineers (USACE) attributed failure of the New Orleans East levees system to overtopping, erosion and subsequent breaching of LPV-111 along the GIWW, as well as other sections of flood protection during Hurricane Katrina in 2005. The existing levee suffered extensive damages from Hurricane Katrina, such that the USACE elected to provide earth stabilization and to rebuild the levee sections. Due to the adverse geotechnical properties of the foundation soils, the Corps deemed ground improvement necessary to stabilize the new levee and to limit its footprint. Wet Deep Mixing Method (DMM) was selected as the most suitable technology for this task.ChallengesDesign: This reach specifically protects East New Orleans and the Bayou Savage National Wildlife Refuge, the largest urban wildlife refuge in the U.S. and home to several threatened or endangered species of birds as well as many reptiles, amphibians and small mammals. The Corps chose DMM due to the sensitivity of the protected marshlands and because the method limits the footprint of the raised levees. The increase in the load bearing capacity of the treated soil significantly decreases the footprint necessary to attain the required height increase. This limitation required the new levee to have steep slopes, drastically increasing the surcharge on foundation soils characterized by overall poor geotechnical properties (soft clays and peats). The design also considered the increased horizontal stresses on the levees due to the extreme storm surges during a hurricane.The design of the 1.6 m diameter (5.25 ft) DMM elements called for overlapping them to form a double auger element that formed buttresses perpendicular to the levee alignment. The contractor installed the buttresses at a maximum on center spacing of 4.7 m (15.5 ft). One additional double auger DMM element was midway between consecutive buttresses at the centerline of the levee to further help prevent settlement (Figure 1)."

Jan 1, 2013

By Robert F. Stevens, Robin Givet, Kenneth Viking

"Summary This paper describes a case of a directional pile installation conducted from an existing oil platform in the Caspian Sea, offshore Baku. Results are presented for 660 mm outer diameter (660 mm OD) conductor piles. Each conductor was equipped with a beveled aluminum toe for directional impact driving and was driven through a 710 mm casing using a Delmag 100–13 diesel hammer and a chaser pile. The 710 mm casings were preinstalled to a depth of 75 m below mud line (75 m BML). The longest impact driven conductor pile on the project was 456 m at end of drive, and reached the terminal depth of 295 m BML.Soil conditions consisted of soft to stiff silty clay to a depth of 30 m BML, underlain by stiff clay to 96 m BML, very stiff silty clay to 200 m BML, and very stiff to hard clay down to 300 m BML.In order to assess the maximum stresses in the conductors and check the performance of the hammer, the driving of each conductor was monitored using a Pile Driving Analyzer (PDA). The hammer fuel setting was adjusted based on the PDA outputs to ensure the conductors were not overstressed during installation. All driving and monitoring operations were carried out from the drill floor.The conductor piles drove easier than anticipated but in the direction predefined by the pre-cut angle of the beveled aluminum toe. The driving system performance was good. Post driving, the SRD were analyzed by either the global method analysis, using WEAP, or by the CAPWAP program.To detect any collision between the conductor being driven and the adjacent wells in production, the well heads were monitored in real time with high sensitivity accelerometers. These accelerometers were connected to an alarm system on the drill floor, triggering a siren and a strobe light should a collision be detected by an abnormal increase of the peak acceleration.IntroductionThe world longest directional impact driven pile was installed in year 2005. The operation was carried out from an offshore production, drilling, and quarters (PDQ) platform located about 120 km east of Baku, in the Caspian Sea.The platform foundation consists of driven piles and 24 slots were available for drilling the wells to the reservoir, located about 3800 m below sea floor. Each slot was fitted with a casing, 710 mm in diameter, running from the top of the jacket to a depth of about 75 m BML (Figure 1). Oil production started in 1997 and by the end of 2003, 14 wells were in operation; 10 slots were therefore still available, either for oil production or for water injection. However, due to larger than expected settlement of the platform, drilling of additional wells was put on hold. After further investigation, experts concluded the settlement was due to an alteration in the mechanical properties of the bearing strata supporting the foundation piles. This alteration was due to either excess soil material transportation, or soil fracture by the drilling fluids (mud), when drilling the first wells. With only 14 wells in production, out of 24 possible, the owner faced a new dilemma: to drill, or not to drill new wells?"

Jan 1, 2014

By Renato P. Cunha

The paper explores a parametric analysis of a four-pile group in contact (hence piled raft) and without contact (hence standard pile group) with the superficial soil layer, under a combined set of loadings (moment M, vertical V and horizontal H forces). The major design parameters of interest, as total and differential settlements, and raft bending moments and shear stresses are assessed under aforementioned distinct conditions. The slenderness ratio of the piles is also varied along the analyses, allowing the establishment of its influence on the derived parameters.

Jan 1, 2006

By Tracy Brettmann, Shailendra Endley, Jason Leary, Shashank Valluru

"Augered Cast-in-Place (ACIP) piles have long been used for deep foundation support in sands due to their high capacity and speed of installation. Very little information exists on the effects on capacity if the auger needs to be withdrawn from the hole prior to grouting. This condition can occur due to various reasons including grout plug ups, equipment issues, and grout supply delivery problems. It can become a major problem for the project team if this happens during production because the capacity of that pile is then in question, potentially resulting in re-design, installation of replacement piles and/or schedule delays. This paper compares the results of two high capacity test piles installed into a dense sand where one test pile was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth and the other test pile was installed utilizing conventional industry standard methods. Identical load tests were then performed on both piles to compare the effects of the two different installation procedures. The load test results were surprisingly similar in this case although the grout take required for the test pile installed in the pre-drilled hole was significantly higher to produce a similar grout return depth.IntroductionAugered Cast-in-Place (ACIP) piles are used extensively along the Texas Gulf Coast due to their combination of high capacity and speed of installation resulting in one of the most cost effective deep foundation systems relative to other options. Soil conditions in this region typically consist of alternating layers of sand and clay in the upper several hundred feet. ACIP piles are routinely installed to depths of over 100-ft to achieve the required capacity depending on the site specific soil conditions and therefore typically extend through and tip into sand layers. Occasionally, due to various reasons like equipment issues and plug-ups, the auger is withdrawn from the hole without grouting. Significant sand in the soil profile could lead to questions about the effect of the auger withdrawal on the pile capacity and load deflection relationship.This paper summarizes the results of two identical pile load tests performed on adjacent piles of the same length with the main difference being one was installed using the standard installation procedure and the other was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth. The load test results were then evaluated using load transfer analyses to estimate the effect of the withdrawal of the auger on the load-deflection characteristics and capacity."

Jan 1, 2017

By M. Makarchian

Existing buildings sometimes experience excessive settlement under their design loads, or due to increased foundation loading, if a change of building use is required. One of the oldest and widely numerical study has been carried out of a simple idealised problem of an underpinned rigid circular foundation to better understand the behaviour of pile used for underpinning and load transfer mechanism from an existing foundation to the underpinning piles. The finite element method has been used for this analysis, with the soil treated as a two-phase elasto-plastic material. It is found that the effect of the length of the pile becomes more significant as pile length increases. As would be expected, the earlier the pile is installed, the less is the final settlement.

Jan 1, 1996

By David T. Farber

"Stabilization of an existing cellular tower foundation system without dismantling the tower or compromising the existing foundation system was accomplished by installation of a jet grouted pile system. The tower was originally designed to be placed on a steep hillside and to be supported by a mat foundation founded on existing bedrock. The as-built conditions of the tower foundation system showed it to be constructed on a combination of loose fill of varying thickness and native stiff silts and gravel material. To avoid the potential of differential settlement, a jet grouted pile foundation system was installed to the top of bedrock. The jet grouted pile system was rapidly installed over a two-day period so as to not delay operational permitting of the tower.INTRODUCTIONA tri-legged lattice cellular communication tower was constructed on the side of a steep hill located in a mature hard wood forest. Access to the site as well as available work area was limited to small track type drill rigs and equipment. The original tower design required the tower to be supported by a mat foundation bearing directly on bedrock. Based on a review of the foundation construction and results of a subsurface investigation, it was discovered that the foundation was built directly over a loose fill material that varied in thickness from 0 to 4.27 meters (0 to 14-ft). Because of the uncompacted nature and varying thickness of the loose fill materials, the tower would be susceptible to differential settlement which, could lead to tower instability.The objectives of this project included the following:• stabilize the mat foundation against differential settlement without removing the existing tower structure or foundation system• rapidly complete stabilization activities to allow operational permitting of the towerSOIL CONDITIONSThe subsurface soil conditions that the tower mat foundation rested on were evaluated by installing three borings in a row from the inward slope portion of the mat foundation (B-1) to the outward slope portion of the mat foundation (B-3). Figure 1 illustrates the subsurface soil stratigraphy. The three borings encountered the following subsurface conditions:"

Jan 1, 2005

By Emre Turk, Suat Gullu, Candan Gokceoglu, Ahmet Sirri, Asli Can

In this study, the ground improvement application applied under the live railway bridge's approach embankments in Sivas, Türkiye was investigated as a case study. The soil profile is mainly composed of orangish conglomerate, clay, silty sandy clay, and under claystone, and mudstone units in the study area. As a soil improvement method, the Deep Soil Mixing (DSM) technique based on the principle of simultaneous mixing the ground while injecting with the water-cement mix, was selected. The application of DSM columns is designed to be 45 degrees horizontal, in order to reach the deepest point of the soft clay units for better improvement against settlement. The core samples were taken from the DSM columns and the compressive strength tests were performed in the laboratory. The results were higher than the minimum designed values. It means that inclined DSM columns were applied successfully, and the excessive settlement problem was solved.

Oct 1, 2022

By Rick Deschamps

A reoccurring problem with support of excavations in urban areas involves the placement of external support components like anchors or nails in right-a-ways, subway and utility setbacks, in areas occupied by adjacent structures, and within the property of non cooperative neighbors. Such a situation occurred for a project in Arlington, Virginia, which ultimately resulted in the preliminary design of a large footing supported cantilever retaining wall that was extremely costly and impractical to build. An innovative design alternate consisting of a series of vertical concrete elements (VCEs) supported by post tensioned tiedowns was proposed to the General Contractor and accepted by the owner. The VCEs were designed to serve as the main structural elements for both the temporary support of excavation system and the permanent wall. The VCE?s were constructed using single bite diaphragm wall panels oriented perpendicular to the excavation face including a rebar cage and tremie concrete. Threaded inserts were placed within the rebar cage to attach the cast in place exterior wall. Overall stability and lateral movement of the VCEs were controlled by high capacity vertical anchors embedded within the VCE. A detailed instrumentation program was installed to monitor the movements of the VCEs with relation to the excavation depth. The paper present the project case history by discussing the design concepts of the VCE, the construction approaches used to install them, the construction challenges encountered, and the performance of the unique system.

Jan 1, 2008

By Achyut Kumar Allady, Praveen Arumughan

NCHRP Synthesis 418 (2011) entitled, “Developing Production Pile Driving Criteria from Test Pile Data” details the occurrence of dichotomy between pile Skin resistance and pile Tip resistance mobilizations at different times for different hammer blows during pile driving operations. With increasing usage of High Strain Dynamic Testing (HSDT) the engineering community started paying more attention to this occurrence of dichotomy resulting in overdriving, pile damage, increased claims, and loss of time. To overcome the dichotomy limitations of HSDT, NCHRP recommends, “the use of superposition to combine the back-calculated tip resistance from a blow on initial drive or from redrive with the back-calculated skin resistance from the early blows at the beginning of restrike”. However, the current practice of external mounted gauges and signal matching for a single blow are unable to evaluate independently the Skin resistance and Tip resistance to achieve the goal of determining the optimum Total Pile Capacity using the superposition. This paper discusses advancements of science and technology with sensors embedded at the pile top and pile tip, the data collected is analyzed by the state-of-the-art FDOT Method to determine Skin and Tip resistances independently for every blow. Independent Tip and Skin resistances each with a Resistance Factor can be summed up to obtain optimum Total Pile Capacity. Additional benefits of determining independent Skin and Tip resistances include obtaining lost skin capacity due to scour, due to pre-drilling/preforming and uplift tension capacity. Furthermore, the benefits of embedded sensors include increased quality control/quality assurance through 100% testing, accelerated construction, life cycle monitoring and asset management.

May 1, 2022

By Djk Arentsen

A new technique to drive tubular piles by impact hammer inside the pile has confirmed a dramatic reduction of noise and the opportunity to save steel. Also a reduction in driving time and a higher bearing capacity has been observed during a test program of this technique. As part of the so-called "Down-the-hole" driving technique, a wave equation analysis has been developed to calculate driveability and pile stress. The main feature of the new "Down-the-hole" technique is the development of a patented device allowing uncoupled penetration of pile tip and pile shaft, which makes it possible to drive both closed or open end piles and reduce the stress level induced in the pile wall. During a test program, a number of instrumented piles were driven and compared with traditional driving of the same pile with the same hammer on top (also instrumented). Also the stresses and performances were compared with precalculations. This paper, explains the technique and presents the test and noise results, in comparison with traditional top-pile-driving. The "Down-the-hole" driving technique is an interesting alternative for special applications where traditional pile driving requires a large wall thickness or in areas where noise is a hot item.

Jan 1, 1996