Search Documents

By K. S. Ho

With the aid of the advanced electronic devices and micro-processors, the quality control of deep foundations can be carried out by Non-Destructive Tests (NDT). Three methods are presented here: the Sonic Logging, Vibration and Stress Wave Analysis Methods. The principles, equipments used, testing procedures and applications are fully described. The correlation of these methods with the conventional tests (mechanical coring and loading test) are studied to give a better understanding of the methods. Several case histories with the test results obtained from a number of sites in Hong Kong and overseas are discussed to show how the pile quality can be examined and especially, how to confirm the effectiveness of remedial works on a defective pile. Recommendation on the percentage of piles to be tested are given at the end of the paper by using statistical method.

Jan 1, 2010

"Full time inspection of drilled shafts by qualified personnel is a necessary part of construction. Detailed inspection procedures for routine inspection are provided in the Drilled Shaft Inspector’s Manual, published jointly by the DFI and ADSC: the International Association of Drilled Shaft Contractors.The use of NDT methods or other observation methods, such as probes, video camera inspection, remote shaft wall inspection devices or various calipers are not suitable substitutes for routine "topside" construction inspection as described in the Drilled Shaft Inspector’s Manual. However, these NDT and other "remote" or indirect observation methods are valuable alternatives to direct entry of personnel into drilled shaft excavations. They should be considered whenever appropriate to reduce the risks of direct entry of personnel into drilled shaft excavations.As described in the Drilled Shaft Inspector’s Manual, observations made during construction are essential for quality construction of drilled shafts. The shaft depth, diameter, plumbness, bottom conditions, reinforcement, concrete continuity, and bearing conditions are most easily checked during construction. Some of these observation methods include excavation around the shaft for relatively shallow inspection, down-hole inspection for end bearing conditions or rock sockets, and video camera devices for remote inspection. In rare circumstances, a drilled shaft can be extracted for inspection. Before concrete placement, the bottom of the shaft can also be probed by drilling or coring to determine if there are voids or soft zones in the material at the base of the shaft.The Drilled Shaft Inspector’s Manual focuses on traditional "topside" inspection for routine drilled shaft construction."

Jan 1, 2004

By Pathik Deb Mallik, Shyamal K. Mitra, Rajiv Kishore, Shuvranshu Rout, Manos De

"This paper presents a case study on the design and construction of a deep underground pit structure constructed inside almost a century old existing plant building. The complexity and challenge for the design and construction lay in executing the work in a difficult subsoil condition especially the presence of deep mica schist. The limited space availability in the existing plant for construction work without hampering regular production in other adjoining areas of the plant made the execution more challenging. Experience with difficult subsoil and proximity to old foundations entailed a non-conventional engineering approach while ensuring complete safety in spite of maintaining the normal operation.INTRODUCTIONTata Steel Processing and Distribution Limited (TSPDL) is a subsidiary unit of Tata Steel Limited (TSL) having a CR processing facility inside the premises of Tata Steel Limited. TSPDL intended to install equipment for a new slitting line inside the existing shed including construction of very deep structure called “loop pit” where the strips from cut CR sheets collect in the form of loops and are recovered as scrap. The entire plant is located within the shed of existing plant. The construction of all foundations including the loop pit is to be executed in the limited area without disturbance to normal production work in balance areas of the plant and also maintain safety and integrity of existing structures.The existing shed is an old structure constructed approximately 80 years ago. The building column foundations are gravity type design of brick masonry supporting only the vertical load from the columns. This type of foundation designed with no eccentricity of loading provides no allowance for implementing any foundation stabilizing design. The present project required civil construction for the new equipment foundations safely within this area."

Jan 1, 2015

By Kishore Kumar B., Eswaran Prasad C R, Srini Naik B., Ramakrishna Raju N

The authors through this paper intend to introduce the non-vibro technique of ground improvement by stone column, being used for the first time in India under the Western Dedicated freight Corridor in Mumbai area. New 2x25 KV double line dedicated freight corridor tracks, capable of carrying 32.5-ton axle load are proposed to be built on this stretch. Non-Vibro Displacement Stone Columns of 900 mm diameter were installed to improve the safe bearing capacity of the soft ground to take the loading of Dedicated Freight Corridor Railway embankment. Vertical footing load tests on single and three column groups were conducted to assess the improvement in the sub-surface condition after installation of stone columns. This paper describes load tests conducted on stone columns and analysis of the obtained results. The observed load settlement behaviour of the improved ground has also been presented. Behaviour of single and group of stone columns have been compared and criteria adopted for arriving at desired factor of safety based on the settlement observed, has also been discussed.

Nov 1, 2022

By Onur Guvener, Kalaiarasi Vembu, C. Vipulanandan

"Installation procedure and the quality of the material used in the construction have significant effects on the behavior of the Auger Cast in Place (ACIP) piles. In this study, Installation and curing of a 760 mm (30 in.) diameter and 12 m (39 ft) long ACIP pile with a design capacity of 1140 kN (128 tons) in hard clay was investigated. Construction quality was monitored using the automated monitoring system where the volume of grout pumped and the pressures were monitored with depth. The curing of the pile was monitored using axial vibrating wire strain gages at four levels and lateral vibrating wire strain gages at two levels. The residual strain and temperature profile in the curing pile was monitored over a period of week to determine the appropriate time for load testing the pile. Axial behavior of Auger Cast in Place (ACIP) Piles in hard clay was studied using full scale load test on an instrumented pile. The load-settlement and load transfer relationships of the pile was investigated based on the load test results. Development of skin friction in the load test pile and the reaction pile was also investigated.INTRODUCTIONAugered cast-in-place piles (ACIP) are drilled foundation installed by drilling a hole with a continuous flight auger to a predetermined depth. Non-displacement Augered Cast-in-Place (ACIP) piles are increasingly used for supporting building, bridges, sound barrier walls and many other structures around the world. In an ACIP pile, depending on the soil type and rate of the auger advance, ground stresses are maintained near the value that existed before construction by using a continuous flight auger, which is never withdrawn until the cementitious material (fluid Portland cement grout) is placed by pumping the grout beneath the withdrawing auger under pressure through the hollow stem of the auger (Vipulanandan, 2005). ACIP piles are typically installed with diameters ranging from 0.3 to 1.0 m and lengths up to 30 m (Brown, 2005) although longer lengths have occasionally been installed. Comparing to the drilled shafts and driven piles of equivalent size ACIP piles can be installed more rapidly with fewer disturbances to the surroundings in favorable geological conditions. Hence the installation procedure and the quality of material used in the construction have significant effects on the behavior of ACIP piles (Vipulanandan, et al. 2007). In this paper construction quality control technique for ACIP piles was investigated. Load displacement and load transfer behavior of pile in compression and tension in hard clay was also studied. The development of side resistance in compression and tension for the load test piles and the reaction pile were also investigated."

Jan 1, 2017

By Scott White, Pishun Tantivangphaisal, Andrew Bell, Chris Barker

There has been considerable advancement in recent years in the tools, both software and hardware, available to allow efficient digitalization of site records during the construction of geotechnical works. Whilst these tools have excelled at replacing handwritten records, the ability to use digital records to validate design and construction requirements in real time or even within reasonable timescales has generally been limited to the development of bespoke ‘prototype’ project specific solutions. This paper describes the development and implementation of an industry standard design schedule and the benefits of the broad adoption of a single database schema for data recorded on geotechnical sites. The former has brought significant improvements and automation of the design process, whilst the latter has enabled the validation of the constructed works against design intent in almost real time. Further details of the standardized design schedule, already publicly available in the UK through the FPS, examples and lessons learnt from implementing digital site record systems on live projects are presented herein. The utilization of cloud computing technology and complex algorithms linking plant/rig instrumentation with design data can further automate construction sites using IoT (Internet of Things) best practices. The authors will share their experience of the recent deployment of a digitalized design-to-construction record system, give recommendations for future development and a call for an industry wide drive to finalize and adopt the AGS Piling data schema.

May 1, 2022

By Abu B. Siddique, Anthony S. Crincoli

"The New Jersey Turnpike Section 2 widening program consisted of widening between Interchange 6 in Mansfield Township, Burlington County and Interchange 9 in East Brunswick Township, Middlesex County. To accommodate large volume of traffic the roadway was widened from 6 to 12 lanes with major modifications performed at four interchanges. The Section 2, NJTA Interchange 6 to 9 Widening Program is a 4.2-mile section of Turnpike roadway which included a total of 12 new or modified structures. In order to facilitate the construction process Section 2 was divided into three construction contract packages. This paper will cover the last and final Contract T869.120.203 which is 1.7 miles in length. The work generally consisted of eight new ramps connection to and from the toll plaza to the new inner and outer roadways. New mainline bridges were constructed over several ramps. A new bridge was constructed to take northbound outer lanes traffic over two ramps along with new mainline bridges over Black’s Creek, Georgetown Road, and Laurel Run. In addition, a new bridge was constructed to take a ramp over Laurel Run and the existing U-turn Bridge was replaced with a new one.For Contract T869.120.203 a total of 74 five-foot diameter drilled shafts has been constructed to support all pier foundations for bridges. Three drilled shafts were tested using Osterberg Load Cells to verify the estimated shaft resistance during design phase. One Osterberg Load Cell test was performed on a demonstration (sacrificial) shaft and the other two Osterberg Load Cell tests were performed on production shafts. This paper compares the estimated total, side and tip resistances with corresponding measured total, side and tip resistances and provided recommendations for future design purpose.INTRODUCTIONTo accommodate large volume of traffic the New Jersey Turnpike Authority (NJTA) decided to widen Section 2, which included Interchange 6 through Interchange 9. The Section 2, a 4.2-mile section of Turnpike roadway that was widened from 6 to 12 lanes with major modifications performed at four interchanges.The New Jersey Turnpike Authority (NJTA) procured AECOM to perform engineering services for the final design of Section 2, NJTA Interchange 6 to 9 Widening Program. Section 2 is a 4.2-mile section of Turnpike roadway that will widen from 6 to 12 lanes and will include a total of 12 new or modified structures. It encompasses modifications of the existing and the design of four new ramps at Interchange 7. The project also includes the modification of two local roads over the mainline, two local roads under the mainline, two maintenance U-turns, and retaining walls. In addition, the project consists of the design of noise walls, sign structures, storm water management basins and the more typical drainage, utilities, lighting, roadway, ROW, and signing and striping design."

Jan 1, 2015

By Dino Kartofilis, Rick Deschamps, Giovanni (John) Bonita

"Anew condominium complex in Arlington, Va., presented some formidable constraints. One was the requirement for a permanent retaining wall to support a 48.5-ft (15-m) cut and an existing 16- story building on top of the slope. Another was the adjacent property owners’ refusal to allow tieback anchors to encroach on their property. The General Contractor (GC) proposed an innovative design incorporating vertical concrete load-bearing elements (LBEs) supported by post-tensioned tiedowns. The owner accepted and the project was successfully completed in 2007.The original designer had proposed a system that included a temporary, raked soldier pile and lagging wall and a permanent cantilever retaining wall with a large piled footing. The system was potentially costly and its constructability questionable.The GC then asked for a design-build alternative to reduce costs and enhance the schedule. The first idea was a diaphragm wall with vertically anchored T-sections. However, configuring a crane to excavate perpendicular sections using grab equipment seemed impossible. There were also utilities approximately 25 ft (9 m) from the existing building, two tiered retaining walls down the slope and a large swimming pool at the base. However, the GC was committed to providing a stable bench 20 ft (6 m) wide along the wall alignment to support the crane.The design evolved to single bite panels using diaphragm wall technology, commonly called LBEs, or barrettes, when they carry vertical loads. For this project, 44 LBEs were horizontally spaced at 9 ft (2.75 m) on center, oriented perpendicular to the wall, extending into bedrock and anchored vertically on the upslope side to resist overturning moments. They were essentially large soldier piles that provided both temporary and permanent support of excavation.An unusual formal agreement was established with the GC to complete the work based on pricing, and prior to completion of final design. This arrangement allowed for an exchange of ideas that increased project efficiencies and lowered costs — without the fear that design concepts would be “shopped” to competitors."

Jan 1, 2009

By Rakam Lama Tamang, Michael J. Byle, Stephen Ernst

"For various reasons, dredging may become necessary in front of existing bulkhead walls, either for channel deepening or for environmental remediation of contaminated sediments. The removal of sediments at the base of bulkhead walls removes support for the toe of the wall that must be assessed. Evaluation of this impact can be problematic for aging bulkheads for which no design or construction records exist. This paper will address the steps that should be taken in investigation and analysis to assure proper assessment and means to address uncertainties and gaps in information. The steps include pre-investigation data review, field inspection, geotechnical and geophysical investigation tools, parametric analysis and design tools. Examples from several bulkhead assessment projects will be provided that include a variety of conditions and tools for application. The focus of the paper will be on the integration of technologies to assess bulkhead geometry, geotechnical properties and stability, structural safety and constructability issues with removal of support, and means of temporary and permanent stabilization for environmental applications.IntroductionBulkheads and quays have existed as long as there have been waterfront activities. Some of the earliest date back to 1200 B.C.E.(Raban, 1987), however in the United States few predate the eighteenth century. Most extant bulkhead structures, and all steel sheet pile bulkhead walls date from the early 20th century or later. These structures function to protect the shore from erosion, support landside activities, and serve as place to moor and offload vessels. Regardless of the age or usage of existing bulkheads, it is essential to assess and protect them if needed where removal of soils on the water side of the bulkheads is planned to dredging.Waterfront BulkheadsExisting bulkhead structures can be classified into two types: Cantilevered, and anchored. Cantilevered walls are completely supported by the soil on the water side, while anchored bulkheads are supported both by the soil on the water side and anchorage on the land side (Figure 1). Walls may be constructed of timber, steel, or concrete. Timber walls may be lagging with soldier piles, cribbing with soldier piles, or timber sheeted such as Wakefield walls (Figure 2). Steel bulkheads are most commonly constructed using sheet piling comprised of interlocking A or Z shapes, though some historic walls were constructed with flat sheets. Precast concrete sheet piling has also been used in construction of bulkhead walls. Anchorage may be provided by steel bars or tendons attached to deadmen, sheet piling, driven piles, or earth anchors."

Jan 1, 2017

By Aminul Islam, Vinay M. Kumar

"About 100 Hectares of land reclamation over the very soft to soft marine clay at Uran Creek in Maharashtra is planned. The depth of marine clay varies from 10m to 24m as observed from the geotechnical investigation. The marine clay was treated with Pre-fabricated Vertical Drains (PVD’s) installed from the elevation of +5.5mCD (chart Datum) and preload/placement of surcharge. A Settlement of soft soil mud under the reclamation was monitored using magnetic extensometer (M) and ground settlement maker (S2). These instruments are installed after constructing working platform at around +5.5m CD. Based on the field instrumentation data, the consolidation parameters were adjusted to match the theoretical and actual settlement plot. The author called this approach as “Back analysis method”. The objective of this paper is to present a case study of instrumented preloading treatment for a thick marine clay deposit. The degree of consolidation in clay strata was determined from magnetic extensometer and ground settlement marker data. Authors also determined degree of consolidation as Asaoka method, Hyperbolic method and Back analysis method and compared the results.INTRODUCTIONExpansion of Container terminal with port buildings, rail container depot, roads and utility buildings at Jawaharlal Nehru Port Trust (JNPT) is planned over a reclaimed land of 100 hectares. Uran creek predominately consists of the estuarine deposit of very soft to soft marine clay. They are characterized by low shear strength, very low bearing capacity and exhibit large settlement when subjected to loading. The additional load causes the significant magnitude of consolidation settlement over a considerable period of time. Thus for development projects on top of soft soil, the postconstruction settlement would be of primary concern.To accelerate the consolidation pre-fabricated vertical drains (PVD) were used. Pre-loading procedure was adopted to minimize the post construction total and differential settlements. PVD’s were installed at 1.0m and 1.2m c/c triangular pattern. Locally available borrow material is used as a reclamation material. The reclamation material has been placed over the existing sea bed level by land based method/end tipping method and created the working platform. The level of working platform is decided based on the tide data and it has been selected such that work should be affected during highest high water level. The PVD has been installed from the working platform and subsequently all the field instruments have been installed from the same level. Five different types of field instruments are installed to monitor ground improvement works."

Jan 1, 2017

By Ray Zelinski

Caltrans sponsored a research project in 1992 which incorporated proprietary and generic pile types. The piles were subjected to axial tensile/compressive loads in deep, soft soils. Descriptions of various pile types and systems, scenarios leading to the proposal to test the systems, and load test results were/will be provided by other presenters at this seminar. Therefore, this paper will focus on the issues surrounding use of test results and proprietary pile systems on Caltrans construction projects. The primary issues facing Caltrans during implementation are as follows: 1) producing pile cap designs for a range of pile types and loads; 2) providing construction specifications which allow fair competition among the system vendors, yet assure design and ultimate capacities; 3) Develop quality control standards for pile system materials and installation techniques which guarantee pile durability for static and dynamic loads; and 4) assure that foundations have adequate lateral capacity.

Jan 1, 1993

By Ali Azizian, Brian Hall

"Driven piles were selected to support the Fraser Heights Bridge bents. Piles were a key component of the top-down construction approach, which was adopted for minimizing potential impacts on an environmentally sensitive wetland. Project requirements mandated verification of pile capacities using dynamic methods. More than 40 Pile Driving Analyzer (PDA) tests were performed. The subsurface conditions were highly variable. On the east side, piles extended through loose sands, soft silts/clays, and two peat layers and were founded in glacial till-like soils at about 45 m depth. However, on the west side, till-like materials were so shallow that it was difficult to drive the piles sufficiently deep to obtain the necessary lateral support. This paper provides an overview of the geotechnical considerations of the bridge design and top-down construction approach, and expands on the presentation of PDA results and how they compared to pile capacity estimation methods and parameters recommended in the applicable design codes.INTRODUCTIONThe Fraser Heights Bridge (FHB) was a component of the Fraser Heights Connector (FHC), a 2 km section of the South Fraser Perimeter Road (SFPR), constructed as part of the Port Mann/Highway 1 (PMH1) Improvement Project. The FHC is located in northeast Surrey BC (Fig. 1).Two major design and construction determinants were: 1) a mandated tight schedule to provide a non-tolled alternative to a new toll bridge; and, 2) an obligation that construction had to occur with minimal impact on the environmentally sensitive wetland the FHB crossed, including limiting the footprint of the permanent and temporary works to less than 45 m2, and prohibiting construction access onto the wetland. Construction equipment was only allowed on the wetland on temporary trestles or on the finished structure. This latter requirement resulted in the bridge being constructed span by span, using a top-down approach."

Jan 1, 2016

By M. Hesham El Naggar, Maged A. Abdlrahem

"Hollow bar micropiles have constructional advantages such as: fast and low-noise and low vibration installation process and small installation equipment, which allow access to tight places. In addition, they have efficient load transfer mechanism, which facilitates carrying considerable load in compression and tension. The common practice is to use diameter ratio of drill bit/ hollow bar (Db/Dh) around 2 in their construction, and they are typically designed assuming type B as classified by the Federal Highway Administration (FHWA). In this paper, the performance and capacity of Hollow bar micropile with different (Db/Dh) ratios are investigated. Full-scale micropiles were installed at a site in Ontario, Canada, and were tested in order to evaluate the uplift performance of Hollow bar micropile with different(Db/Dh) ratios. Two micropiles with two different ratios 2.25 and 3 were constructed and tested. The total length of the micropiles was 6m with embedded length of 5.75m. The soil at the site was primarily medium dense to dense sand. The results of the load tests are presented and discussed. It was found that the uplift capacity of the micropile increased by about 19.5% as Db/Dh increased from 2.25 to 3.INTRODUCTIONMicropile is a small diameter, less than 300 mm, drilled and grouted pile and is typically reinforced according to Federal Highway Administration (FHWA, 2005). The technology of micropile was introduced in North America in 1970’s, but the growth in the east coast of United State was intense compared to all other cities around the globe (Bruce and Nicholson, 1989). Nowadays, micropile construction is used extensively worldwide as a viable solution that offers several advantages such as fast installation in low headroom, minimal disturbance to the adjacent structure efficient load transfer due to high grout to ground bond strength. As the method of grouting has major influence on the grout – ground bond strength, FHWA has classified the micropiles into four categories. Type A: the grout is placed under gravity and no pressure is required. Type B: The grout is typically pressurized under a pressure range from 0.5 to 1 MPa as the temporary casing is withdrawn. Type C: the grout is placed in two-step process. First, the grout is poured under gravity only as in Type A. Before the hardening of the grout, similar grout is pressured of at least 1MPa without the use of packer. Type D: Like Type C, it is a two – step process, the grout is placed under gravity as in Type A and sometimes pressurized as in Type B. After hardening of the initial grout, additional grout is pressurized between 2 to 9 MPa through sleeved pipe by using packers, as many times as needed. According to this classification, hollow bar micropile is usually designated as Type B. However, the construction technique is completely different from Type B. Recently; there is a trend to supplement the four types of micropiles by Type E as represent to hollow bar micropile (Timothy et al, 2012). The construction method of hollow bar micropile involves two main stages which can be performed in one–step process: advancing the drilling bit attached to a threaded hollow bar to the required depth; and pressurizing the grout through nozzles of the drill bit."

Jan 1, 2016

By C. Vipulanandan

Installation procedure and the quality of the material used in the construction have significant effects on the behavior of the Auger Cast in Place (ACIP) piles. In this study, Installation and curing of a 760 mm (30 in.) diameter and 12 m (39 ft) long ACIP pile with a design capacity of 1140 kN (128 tons) in hard clay was investigated. Construction quality was monitored using the automated monitoring system where the volume of grout pumped and the pressures were monitored with depth. The curing of the pile was monitored using axial vibrating wire strain gages at four levels and lateral vibrating wire strain gages at two levels. The residual strain and temperature profile in the curing pile was monitored over a period of week to determine the appropriate time for load testing the pile. Axial behavior of Auger Cast in Place (ACIP) Piles in hard clay was studied using full scale load test on an instrumented pile. The load-settlement and load transfer relationships of the pile was investigated based on the load test results. Development of skin friction in the load test pile and the reaction pile was also investigated.

By Mario Mauro

Tuttle Creek Dam was constructed by the U.S. Army Corps of Engineers in the 1950?s on the Big Blue River in north-east Kansas. Since the dam is located in a seismic area, the safety of the dam was re-evaluated under the national U.S. Army Corps of Engineers Dam Safety and Assurance Program. After a series of studies and analyses performed by the Kansas City District of the U.S. Army Corps of Engineers, in 2003 the Department of the Army authorized the implementation of the plan ?Stabilize Foundation Soil without Drawdown Alternative?, during a 7-10 year construction period. As part of this plan, in 2006 Treviicos South carried out a large scale jet grouting and deep mixing test program downstream the dam. The test program included the installation of twenty-seven double and triple-fluid jet grout columns and twenty-seven jet-assisted deep mix columns. The jet grout columns were constructed at different levels of specific energy and cement content. The deep mix columns ranged in diameter between 3 ft and 6 ft. During column placement, the drilling and grouting parameters, pore pressures, and soil movements were instrumented in real-time. The downstream test area was enclosed by a cement-bentonite wall extended to bedrock, which allowed a 35-ft deep open excavation around the 45-ft deep columns. The exposed jet grout columns measured up to 15 ft in diameter, exceeding the anticipated target diameter. In addition to coring, some of the jet grout and soil mix test columns were saw-cut along the group axis, providing useful information on the internal column structure.

Jan 1, 2008

By Jerold Bishop, Grant Bearss, Aleksey Egorov

"When a shock wave is released in the bottom of a drill hole filled with wet concrete slurry, the result is called an electrohydrodynamic effect, or EHDE. The energy is carried through the fluid with minimal loss because the slurry is an incompressible medium. Repetitive discharges provide a series of energy pulses that compact the soil along the pile shaft and at its base. The process is analogous to repeated applications of low-energy blast densification or to dynamic compaction. In general, the process is not depth dependent. EHDE was identified in the 18th century by an American scientist who observed that a spark between two electrodes placed under water induced a burst of pressure. In 1957, two Russian engineers formulated a process and received a patent for a method of creating a pressure wave by transforming power from an electrical discharge to a mechanical impact. They derived more than 200 applications for technical and industrial processes.In the 1970s, civil engineers at the Engineering and Building Institute in St. Petersburg, Russia, began to look at EHDE to improve the capacity of drilled piles. Early experiments showed that electric discharges in a wet concrete slurry mix could create a pressure wave of up to 26 MPa (3700 psi). Later tests demonstrated that this pressure level could be created in a drilled pile hole. The researchers devised equipment and in the early 1990s began to study pulse technology as applied to drilled piles.This application was accepted into the Russian Federation Building Code in the 1990s. The code treats “regular” drilled piles with equivalent bearing area as having roughly half the capacity of a driven pile. However, the code considers drilled piles treated with the EHDE technique a direct “one for one” substitution for driven piles and allows higher values if the capacity is established by static load testing. Hundreds of projects have been completed in Russia using this technology to value engineer drilled pile projects. In several instances, the number of drilled piles installed was fewer than half of the number originally planned for due to the capacity increase that EHDE-treated piles provided.Drilled PilesIn drilled pile construction, the EHDE process creates a mechanical pressure wave that impacts the base and sidewall of a drilled pile shaft. Soft, poorly consolidated or loose soil is compacted by successive pulses of pressure created by electrical discharges. These mechanical impulses are made by inserting a discharge probe into the wet concrete slurry. A discharge across the tip of the probe creates the pulse that travels outward to the sidewall and base of the drilled pile through the incompressible medium of the slurry. The power pack ratings for equipment presently in use are 35 and 50 kJ (kilojoule).Each pressure wave strikes the soil, causing compaction and expanding the hole. Workers apply the pulses until the size of the hole stops increasing. They watch the slurry level during pulsing. When the level quits dropping, further soil compaction in the drill hole sidewalls and base is not possible. After the pulse process is complete, workers insert a rebar cage and the pile is finished.The process does not alter the soil mineralogy. The electrical discharge is internally grounded and does not arc to the sidewalls of the drill hole. Soil is not scorched or altered in any manner; it is only compacted by the pressure wave. This technique has been used in urban areas with no effect on electrical or electronic equipment."

Jan 1, 2009

By Venkata Krishnaiah Yeddala, Sai Vivek Adari, Suresh Kumar Velugu

Assam cancer care foundation (ACCF) proposed the construction of hospitals and related facilities across 18 locations in the state of Assam-India. Tezpur is one among the 18 locations of Assam with high seismic risk. The strata at the site are comprised of mostly fine silty sands of lower SPT- N values. The water table is also encountered and ranging from 1 m to 2 m below EGL. Since the site lies in seismic zone V as per IS 1893, detailed liquefaction analysis is carried out for all five boreholes and indicates that soil is liquefiable and ground improvement is inevitable up to a depth of 15 m below existing ground level. To mitigate the liquefaction potential and enhance the seismic performance of the soil, ground improvement using stone columns by Wet top feed Vibro-replacement method is proposed. Also, the differential settlements can be avoided effectively under the raft foundation with Vibro Stone Columns. In this paper, field test validation results such as Pre and post-SPTs and ECPTs to access the extent of ground improvement, along with other information adopted in this project presented.

Nov 1, 2022

By I. D. Dayal, Anil Kumar Jain

"Cutoff walls are frequently used to slow down or prevent seepage of water through and/or around dams. Cutoff wall is a type of seepage barrier structure designed to reduce the flow of water underneath temporary or main dam. There are number of techniques for the construction of cutoff walls including concrete, Jet grouting and permeation grouting. NHPC LTD, a premier Govt. of India undertaking has been instrumental in the hydropower development within the country & in nearby countries like Nepal & Bhutan since last four decades. NHPC LTD has completed more than 20 hydro-electric projects with total installed capacity of 6587MW (including capacity addition by JV- NHDC). In all these projects, different types of dams and spillways were constructed in not so benign to extreme challenging geological set up. There has always been challenge associated with the temporary diversion works. The project sites sometimes incur huge river bed excavations in case of concrete gravity dam founded on rock foundation at large depth. The challenges for minimizing the seepage have been well taken care by constructing the dedicated seepage barriers. The construction of cut-off walls have progressed from “conventional continuous trench backfilled with conventional concrete or plastic concrete” to “grout curtain”, to “jet grouting” to the “concrete cut-off wall” , the last being the most sophisticated & credible seepage barrier.The efficiency of the cut-off walls are monitored by the seepage quantity observed (reduction of the seepage flow), uplift pressures or exit gradients after construction of cut-off walls. For construction of the main concrete dam, required space is created by the river bed excavation for placing the dam foundation on sound rock. Sometimes there is deep river bed excavation from 30 to 40 m depth or even more as per the available rock profile. Temporary coffer dams are constructed for diverting the river flow through diversion tunnels / channels etc. In deep river bed excavation; there are high chances of the significant seepage through the coffer dam foundation / river bed material due to high hydraulic gradients. Seepage and piping are the main causes of the failure / damage of the temporary coffer dams. If the seepage quantity is too high, then it becomes difficult to handle it by dewatering in the dam pit. Dam concrete is required to be placed unhindered to have a monolithic construction of dam blocks & to have faster construction in the working season. Cut-off walls increase the seepage path considerably thus reducing the exit gradient and further reduction of the seepage thus helping in maintaining the seepage free area for working."

Jan 1, 2016

By Tsunenobu Nozaki

"Basically, the “Press-in Piling Method” was invented to eliminate construction nuisances, such as noise and vibration which have been serious unsolved problems for advancing societies over a long time. In the construction industry, piling works have been a major cause of noise and vibration, because most piling methods utilize dynamic load to install piles into the ground. The secret of the Press-in Piling Method is to utilize static loading to install pre-formed piles rather than dynamic load. The piles are hydraulically gripped and jacked into the ground by the special piling rig known as the “Silent Piler”. Therefore, the piles can form a robust and firm foundation, which is another advantage of the Press-in Piling Method.The Press-in Piling Mechanism and Implant Foundations The basis of the Press-in Piling Method is simple. The Pres-in Piling Machine installs a preformed displacement pile into the ground by static jacking force. The reaction for the Press-in Force is generated by gripping previously installed piles, which are called “Reaction Piles”. Due to this, the Press-in Piling Machine can produce a powerful piling force whilst only requiring minimal machine size.With the Press-in Piling Method, as piles are pressed into the ground, they are incorporated with the surrounding soils, which provides a large bearing capacity and passive horizontal resistance. These embedded foundations which are firmly anchored into the ground are known as “Implant Foundations”. Being embedded into the ground, the foundations are resilient and maintain their serviceability even in the worst credible design conditions."

Jan 1, 2015

By Mark R. Svinkin

"Construction equipment and operations usually produce soil and structural vibrations which may harmfully affect various structures and also the content of buildings and houses. The level of structural vibrations depends on a number of factors such as characterized sources of vibrations, soil conditions, and susceptibility of structures. There are certain knowledge and experience for managing the effects of construction vibrations which require implementation of condition survey of structures, information on construction dynamic sources and soil conditions at a site, evaluation of possible vibration effects on structure, calculation of ground vibrations before construction, use mitigation measures to decrease vibrations, and a choice of appropriate vibration limits. The paper presents the application of known concepts for assessment of vibration effects on structures from bridge constructions.INTRODUCTIONVibrations producing by construction activities such as pile driving, dynamic compaction of loose soils, demolition work, heavy construction equipment and trucks can affect adjacent and remote structures. Vibration effects on structures, sensitive devices and processes may create significant practical problems. Legal actions are often required for solutions of vibration consequences. The level of construction vibrations depends on dynamic sources, soil conditions at a site in particularly availability of soils with settlement potential, distances from the sources, parameters of waves propagating at a site and susceptibility rating of adjacent and remote structures. It is likely that intolerable structural vibrations from direct vibration effects of impact pile driving and resonant floor vibrations from vibratory pile driving may be induced in adjacent structures to construction sites.Foundation settlements resulting from soil vibrations in loose soils usually occur in the proximity of dynamic sources, but it is important that dynamic settlement may happen at various distances from the source. There are such examples. First, Kaminetzky (1991) mentioned a case history of building settlements developed at a distance of about 305 m (1000 ft) away from a pile driving site. Foundations of the buildings were underpinned on piles down to the tip elevation of the new driven piles to prevent building settlements. Second, Lacy and Gould (1985) shows that the peak particle velocity (PPV) of 2.5 mm/s (0.1 in/s) of ground vibrations could trigger dynamic settlements at distances up to 30.5 m (100 ft) from driven piles."

Jan 1, 2016