Search Documents

By François G. Bernardeau

Cement-bentonite (C-B) slurry walls have been used for ground water cutoff in deep excavations, contamination containment, and other applications. Hydraulic conductivity is of great concern for cement-bentonite slurry walls. The quality control program usually specifies permeability and strength tests to be performed in a laboratory on samples cast in the field and cured for a certain time. Currently there is no widely accepted in-situ test method for the performance of the constructed slurry wall. A recently constructed cement-bentonite slurry wall in South Carolina included a 200-foot-long test section done in advance of the production of an 8,300 foot-long wall. Intensive tests and investigation were conducted during and after the test section construction: Monitoring piezometers were installed using wet insertion method and packer tests were conducted in boreholes drilled in the post-28-day-cure slurry wall. The permeability measured from the packer tests was about two orders of magnitude higher than the design and the laboratory test values. Additional investigation was performed using a video camera to inspect the borehole walls especially the packer test sections. Test pits were excavated to observe both sides of the cement-bentonite slurry wall. A thorough inspection was conducted to evaluate the integrity of the wall. The lessons learned and issues regarding the disturbance effects of in-situ testing of cement bentonite slurry walls is presented and discussed.

Jan 1, 2008

By Giovanni A. Bonita

The United States Capitol Visitor Center (USCVC) is one of the largest underground structures ever constructed in the Washington, DC, metropolitan area. The 600,000 ft2 (55,750 m2) structure is entirely underground and immediately adjacent to the shallow foundations of the existing U.S. Capitol building. Interior building columns for the USCVC were supported on 186 drilled shafts that varied in diameter from 4 to 9 ft (1.2 to 2.9 m) and in length from 15 to 45 ft (4.6 to 13.7 m). The vast majority of the building utilities were located beneath the basement floor slab. It was decided at the onset of the project to proceed with construction prior to completion of the design drawings, and coordination between the underslab utilities and the drilled shafts had not yet been finalized at the onset of drilled shaft installation. Given depth and location restrictions of the outlets, relocation of the bulk of the utilities was not possible. Almost half of the drilled shafts were affected, leaving redesign as the most feasible remedial solution. The redesign involved adjustments to the shaft length, diameter, and bell. It took place on a case-by-case basis, sometimes only minutes before installation began. Coordination between the field and design team was excellent, and delay associated with the redesign efforts was minimal. In addition, the detailed, high-quality field records kept by both the contractor and field engineers allowed for accurate and fair estimations of the added drilled footage and concrete volumes placed. The additional service fee, which was minimal, was settled quick and fair.

Jan 1, 2006

By Thomas M. Gurtowski

The New Pacific Northwest Baseball Park, now known as Safeco Field, is located directly south of the Kingdome in Seattle, Washington, and will be the new home of the Seattle Mariners baseball team. The location of the ball field is shown on Figure 1, Vicinity Map. The seating capacity is 45,600, and outfield distances are 331 feet in left, 405 feet in center, and 326 feet in right field. The overall dimensions of the stadium are 680 by 800 feet. It is bordered on the east by the Burlington Northern Santa Fe Railroad main line. A unique aspect of this ballpark is the retractable roof with a north-south span length of 660 feet. The roof consists of three separate sections that roll on elevated rails running east-west on the north and south sides of the stadium. The soil conditions consisted of near-surface fill underlain with alluvial and Estuarine deposits to depths of 60 to 80 feet. The bearing soils consisted of very dense, glacially overridden deposits. Groundwater is 4 to 7 feet below the ground surface, and the alluvial deposits are subject to liquefaction during a strong motion earthquake.

Jan 1, 1998

By Richard J. Finno

Detailed measurements made at a test section adjacent to a deep braced cut and other published data are combined to illustrate the limitations of the common methods of predicting movements associated with excavations in soft to medium clay. While past performance data can be used to estimate expected responses before construction in many cases, actual wall and soil deformations throughout construction can only be estimated using finite element procedures. Success of such analyses depends equally upon considering all aspects of construction that induce strains in adjacent soil, such as wall installation, excavation and bracing sequence, and time, and adequately modeling soil stress-strain behavior. Even when these two criteria are met, soil deformations can not be predicted adequately when strain levels exceed those that produce peak shear stress.

Jan 1, 1991

By D. Dreher Whetstone, Paul M. Blakita, Christopher M. Reith, Ravi P. Malviya

"Micro-piles are small diameter (5 to 10 inches), cast-in-place piles which can develop high load capacities by bonding with soil or rock. Micro-piles are particularly well-suited for moderate to heavily loaded structures requiring deep foundations in difficult subsurface conditions, such as karst, bouldery mine spoil, or unsuitable fills with concrete debris or other obstructions. Attempts to install conventional deep foundations including driven piles, drilled piers, or auger-cast piles are likely to be fraught with construction difficulties and disputes, delays, cost overruns, and may be unfeasible in some cases. Micro-pile installation equipment is very effective in installing foundations through such overburden or rock materials.This paper presents case histories of Micro-pile installations on two projects with difficult soil/rock materials. The project sites are located in Charles Town, West Virginia and Masontown, Pennsylvania.Charles Town, West Virginia ProjectThe Charles Town project entailed construction of a four-story pre-cast concrete garage. Triad Engineering, Inc. performed a geotechnical investigation for this project (Triad, 2001). The subsurface, geologic, and project specific information described in th is paper are largely based on the aforementioned geotechnical report.Ground ConditionsThe project site is located in Jefferson County, West Virginia, and is mapped to be underlain by the Elbrook Formation. This formation is described as argillaceous, dolomitic limestone with beds of dolomite and aphanitic and algal limestone (Dean, et al. , 1990). The carbonate rocks at the site were characterized as ""moderately solution-prone, highly calcareous and weathers differentially to produce a pinnacled or ""sawtooth"" top of rock profile. (Triad, 2001 )"" Overburden soils consist of low to high plasticity, fine grained residual soils formed by weathering of the parent carbonate rock. The residual soils include variable proportion of sand and rock fragments."

Jan 1, 2005

By William (Bill) H. Walton

"I arrived in Chicago in 1993 with Dr. Ralph Peck’s University of Illinois bulletin titled Engineering Properties of Chicago Subsoils (Bulletin 429), which he published in 1954 with William Reed. Being an outsider, I wanted to learn from Chicago geotechnical practice leaders that included Clyde Baker, Jr., John Gnaedinger, Charles Pfingsten, Dr. Safdar Gill, Robert Lukas and Dr. Jorj Osterberg, who have influenced foundation designs for the structures that make up the contemporary Chicago skyline. One of my immediate goals was to get the Illinois Structural Engineering license to be on par with the likes of Eli Cohen, Mike Tylk, Stan Korista, Bob Halverson, Joe Burns, Ron Johnson, Bill Baker, Bob Sinn, Chuck Anderson and Dave Eckmann, who have led their structural firms in the design of the skeletal core and frames of many of Chicago’s iconic buildings (and for many other buildings around the world). From my time with GEI Consultants (GEI), then on with STS Consultants (STS, and now AECOM), and now back with GEI, I have had the opportunity to analyze and design foundations and, with the help of many skilled foundations and building constructors, to verify that predicted foundation performance matches actual movement data. The theme of Chicago’s foundation design practice is to assume and verify. In 1948, Peck published the History of Building Foundations in Chicago (Bulletin 373) that was updated in 1998 by Baker, Pfingsten and Gnaedinger, who meticulously documented hundreds of Chicago’s foundations, and have shown the value of advanced analyses and testing to advance the deep foundation design practice that includes a variety of high-capacity driven and drilled deep foundations. Mehmet Uyanik, Peck and Baker have made Chicago’s subsurface into a full-scale foundation test laboratory. They confirmed soil mechanics principles like Terzaghi’s 1-D consolidation theory when early foundations bearing on sand-clay crust over soft to medium silty clays (e.g., Auditorium, Masonic Temple, Monadnock Block and Old Board of Trade buildings) took 40 to 60 years to consolidate clay 1 to 2 ft (0.3 to 0.6 m). They also confirmed proven increases in bearing pressures based on measured performance of deep foundations bearing on the glacially derived hardpan clay till and in solid dolomite that underlies Chicago."

Jan 1, 2017

By C. Vipulanandan

It is critical to monitor the ground conditions during excavation and drilling of boreholes during construction to identify possible changes in the soil and rock formations. Drilled shafts are increasingly used as foundations to support structures, bridges and other facilities in geomaterials such as soft-rocks and hard clays. Locating the bottom of the borehole during construction with the required design strength is critical. Hence developing a simple device that could be easily adapted/used with the drilling tool was of interest in this study. Determining the shear strength of the geomaterial in the borehole and at various elevations including the bottom of the borehole can lead to better quality control of construction by identifying the various layers based on strength. In this study, a down-hole penetrometer (DHP-CIGMAT) was designed, built, calibrated and tested in the field to determine its effectiveness in measuring the strength of soil/soft rock in the boreholes. Based on limited field tests, linear correlations between geomaterial strengths and DHP-CIGMAT deflection have been developed. The DHP-CIGMAT can be used to identify soils and soft rocks.

By Ørjan Nerland, Torgeir Haugen, Astri Eggen, Kjell Karlsrud

"Ground improvement by the deep dry mixing (DDM) method is used in Norway since the late 1970's. A brief review is given of the Norwegian guideline for ground improvement with DDM issued in 2012, but focus is on practical examples and experiences related to improving the stability of excavations and natural slopes in soft clays. Two examples deal with experiences from 10 to 18 m deep excavations in soft and partly highly sensitive clays, where DDM panels and block stabilization were used to both give sufficient stability against bottom heave and to limit lateral wall displacements. A third case deals with improving the stability of a natural slope in quick clay by installing DDM panels near the crest of the slope. To limit disturbance and excess pore pressures generated during the DDM works, vertical drains were installed in advance in between the DDM panels. This ensured that the excess pore pressures generated by the DDM works (up to 150 kPA) dissipated quickly, which was instrumental to avoid triggering a landslide during the stabilizing works.INTRODUCTIONThe lime column (LC) method developed in Sweden and Japan in the mid 1970's (e.g. Broms and Boman, 1977). Since then, there have been significant developments in Scandinavia and around the world in terms of rigs, mixing machinery and tools, and type of binders used. The method, presently named the ""Dry Deep Mixing"" (DDM) method in contrast to the wet deep mixing methods (WDM) that also have developed significantly over the past decades, e.g. Kitazume and Terashi (2013). The first application of the DDM method in Norway was in the late 1970's to improve the stability of an excavation in quick-clay, then using only lime as binder. Most DDM applications in Norway have also thereafter been to improve the stability of cuts, supported excavations or natural slopes in soft clays. The Norwegian Geotechnical Society (2012) issued in 2012 “Guidelines for design of ground improvement with DDM methods"". The following highlights design issues dealt with. The paper focuses however, on some practical cases where DDM has been used to improve stability of deep excavations and a natural slope in soft and partly highly sensitive clays."

Jan 1, 2015

By James P. Stewart

This case history describes the engineering design and construction for the Contractor of a 35-ft-deep excavation for an 800-square-foot addition to an existing sewage pump station. The site posed unexpected geotechnical complications that included deep gravelly soil, a history of local construction difficulties, groundwater consisting of heavy salt brine, and the need to underpin the existing pump station. The project took an interesting twist when the Owner issued a change order limiting the dewatering discharge to a fraction of that required to lower the water table. This documents the interesting circumstances of this job and documents the unusual subsurface conditions in the Syracuse, NY Lakefront area.

Jan 1, 2003

By William E. Lardner

Interlocking caisson walls developed from conventional "soldier pile and lagging" shoring. In the latter, the soldier piles receive directly most of the soil load. Natural arches form in the soil behind the shoring; the lagging supports little more than the segment of soil inside the arch. Fig. 1: A typical layout of a lagged wall [ ] Fig. 2: A typical layout of an interlocking caisson wall [ ]

Jan 1, 1987

By Vijaya Bhushan Rao, Jason Redgers

The typical Vibrocompaction projects undertaken in the UAE are on reclaimed Sands. These Sands which are predominantly the crushable, calcareous, carbonate sands found locally as opposed to the more common quartz or silica sands that are featured in most design literature. The famous reclamations such as the iconic Palm Jumeirah in Dubai, often have specification for mitigation of liquefaction induced settlements, bearing capacity increases and total and differential settlement requirements. Often these performance targets are achieved by the means of achieving a particular relative density that are generally measured by a defined Cone Penetration Test, CPT targeting values of cone resistance (Qc), MPa at respective depth zones. In this paper some case studies are presented, where soil suitability for deep compaction by vibratory methods was firstly assessed for suitability using the Massarsch, 1991 compactability chart prior to the application of vibrocompaction and its subsequent evaluation. One such project named the Island Development required 17 to 23m depth of penetration only to treat the lower 5 to 6m of sand above rockhead as eventually the top 15m of sand will be further excavated to allow for the construction of basement. The paper will present pre and post CPT results, the results of initial site calibration trials and evaluation of the completed works.

Oct 1, 2022

By M. Pernot

A 12 m-deep excavation has to be perfomed in the Shanghai soft clay to install an underground electric substation. This article was originally intended to study the behaviour of the wall, the excavation bottom and the surrounding ground during the excavation. Since the works are behind schedule, and the data referring to the excavations are not, therefore, available, the article is limited to a presentation of the analysis methods that we envisaged for the study of the behaviour of the excavation.

Jan 1, 2010

By Lok M. Sharma, Deep K. Khatri, Bradfield. Brett

"A shored enclosure was required to access a control structure upstream below the dam of a deep lake. The shoring involves the interaction of the structure, soil, and water and the loads imposed include the hydrostatic forces of the water, soil pressures as well as dynamic forces due to currents and waves. Deep excavation support systems have traditionally been designed using classical methods that involve direct computations of earth pressures. However, traditional analysis does not take into account soil-structure interaction. Numerical modelling offers better means to analyze soil-structure interaction. This paper presents a 2D finite element (2D-FE) analysis of a deep excavation support structure that was required to remove and replace a control structure at the upstream toe of a dam. The sheet-piling shoring was designed to withstand the lateral pressures from 14 m deep free water and 5.5 m deep excavation below the free water to reach the required excavation level to replace the gate structure. Elastic-plastic analyses were performed to predict the stresses and deformations of the complicated shoring structure and excavation bottom. The soil parameters, procedures used to develop the 2D-FE model, and the results are discussed in this paper. The shoring system is currently under construction.INTRODUCTIONA deep shoring system enclosure is required to keep out water and soil and to provide a support for unbalanced loadings due to dewatering and/or, excavation in order to permit construction of the permanent structures in the dry. A braced shoring system consists of a single wall sheet piling which is driven into the ground to form a “box” around the excavation site and is braced on the inside. After bracing the sheet piling, seal concrete is placed into the bottom to prevent water from seeping into the open excavation from underneath the sheet piling, and the water is pumped out to provide the dry work area. The braced shoring involves the interaction of the structure, soil, and water and the loads imposed include the hydrostatic forces of the water, soil pressures as well as dynamic forces due to currents and waves. Deep excavation support systems have traditionally been designed using classical methods that involve direct computations of earth pressures, (active, passive, or apparent pressures). There have been some uncertainties regarding the actual distribution of earth pressures due to influence of the support wall flexibility, as these traditional methods do not take into account soil-structure interaction. Numerical modelling offers better means to analyze soilstructure interaction."

Jan 1, 2017

By Giuliana A. Zelada

This paper reports on a study of 43 compression load tests (five fully instrumented) and ten pullout tests of auger cast-in-place (ACIP) piles in sand. Eight design methods reported in the literature were used to predict the measured pile capacities. Ultimate load capacities of the ACIP load tests were determined using two different definitions of ultimate capacity and compared with predictions. Load transfer behavior was determined from a study of the fully instrumented pile tests and compared to predicted values. Recommendations are made regarding the design approach most appropriate for these foundations and the best procedure for estimating ultimate capacity from pile load tests.

Jan 1, 2000

By M. Melih Demirkan, Jared Deible, Michael Rosenmeier, Mazen Elias Adib, Juan J. Gutierrez, Raghav Ramanathan

Dewatering and groundwater control is required frequently for construction projects and needs to be accounted for and dealt with care during design and construction to complete the project successfully. Dewatering can cause changes in porewater pressure, which changes the effective vertical stress in a soil mass. Dewatering can also cause changes in groundwater chemistry which in turn can cause changes in porewater pressure and also dissolution of soluble minerals in the soil and rock. The Guideline developed in this study addresses the engineering issues, approaches to lessen the potential risks associated with construction dewatering, and presents dewatering practices to support dewatering applications regulated by the Municipality of Abu Dhabi City (ADM) in the United Arab Emirates (UAE). The subsurface condition within the city presents significant geotechnical problems due to presence of shallow subsurface cavities and soluble minerals in the soil and rock. Therefore it is critical to develop standards for dewatering practices to provide information for local dewatering engineers and contractors with special emphasis to control and to eliminate the subsidence/collapse problems related to dewatering projects within the Abu Dhabi city. The ADM is also responsible for approval of permit applications for projects that involve dewatering. In order to minimize the risk related to subsidence/collapse problems due to dewatering, construction companies and dewatering contractors need to be informed about possible mitigative measures that can be employed to reduce risks. The guidelines were developed as part of this study based on detailed analysis of the local subsurface conditions. A set of rules and regulations are developed for geotechnical and hydrogeological investigations, dewatering design and monitoring criteria depending on the hazard zones, proximity of excavation to critical structures, excavation depth. The Guidelines include examples of permit application packages for three types of dewatering projects; one involving shallow dewatering, one involving intermediate depth dewatering, and one involving deep dewatering. These Guidelines are considered as living document and will be updated as required, as additional information is collected and additional local experience is gained.

Jan 1, 2016

By David S. Graham, Benjamin Turner, Paul J. Axtell

Seismic challenges were at the forefront of design for two parallel replacement bridge structures over the Arkansas River as part of the I-30 Crossing Project in Little Rock, Arkansas. Although not an area of the country typically associated with high seismicity, proximity to the New Madrid Fault Zone resulted in design ground motions sufficient to trigger liquefaction in alluvial channel and point bar deposits. A detailed post-award subsurface investigation program utilized CPT with complimentary borings to obtain samples for laboratory testing to assess the continuity of potentially liquefiable layers, from which we concluded that continuous zones of liquefaction across the extent of the north approach could lead to lateral spreading towards the river. An overview of the foundation and superstructure design to resist lateral spreading forces in accordance with the latest published design guidelines and research is presented. Other seismic aspects of the design are covered including timber pile ground improvement to mitigate liquefaction at the north approach embankment and foundation input motions that differ from code-based ground surface motions due to foundation stiffness, strength, and geometry. The project showcases an example of successful collaboration between geotechnical and structural designers with contractor input to address seismic challenges in the South Central US. Furthermore, the importance of considering kinematic demands on columns and other superstructure components – not just foundations – is highlighted.

Sep 8, 2021

By P. Ventura

Reliability of the liquefaction analysis is based on data plotted as by piezocone, as by deep vibrocompactation monitored tests. The negative porewater pressure, re lated to hydrostatic value, recorded by piezocone, is a good marker of the absen ce of the liquefaction. Systematic measures of the ground settlements, inside the vibroinfixed steel pipe, allow to locate the liquefable strata with loose density. Experimental study of the combined soil improvement by stone columns is carry out in particular in sea bed. The interaxis of the columns for the best efficiency is valued as of the vibrocompactation, as of the drainage effects, especially during earthquake.

Jan 1, 1989

By Mohamed Elgouhary, Carol L. Tasillo, Daniel Koziol

"The Bolivar Dam, located near the Village of Bolivar, Ohio is one of a system of dams designed to provide flood control and water conservation in the Muskingum Watershed. The Bolivar Dam is a “dry dam” that only impounds water during flood events. In order to address problematic seepage, which negatively affects the structural stability of the dam, the U.S. Army Corps of Engineers (USACE) designed a partial-depth and partial-length Seepage Barrier Wall (SBW) through the upstream slope of the dam. For this project, TREVIICOS constructed a 36 in (914 mm) positive SBW by plastic concrete panel wall method and excavated using hydromill and clamshell equipment. The plastic concrete was manufactured on-site, which allowed for enhanced quality control and prompt service. This required the installation, commissioning and operation of a concrete batch plant on-site. This paper presents the challenging aspects of the design, manufacture and placement of the plastic concrete for the SBW in order to meet contract strength and permeability requirements as well as workability requirements necessary for tremie concrete placement.Project General InformationBolivar Dam is located in Northeast Ohio (Fig. 1). It is one of a system of sixteen dam projects designed to provide flood control and water conservation in the Muskingum Basin, which covers 20 percent of the State of Ohio (Fig. 2). Bolivar Dam is on Sandy Creek, a tributary of the Tuscarawas River.The Dam has been constructed, operated and maintained by the USACE, for the Muskingum Watershed Conservancy District. Its construction was completed in 1937 and it has been in operation for flood control since 1939.Bolivar Dam is a rolled earth fill dam, with a typical embankment section made of a central impervious core flanked upstream and downstream by a pervious outer shell with downstream rock toe. The embankment has a maximum height of 87 ft (26.5 m) and a crest length of 6,300 ft (1,920 m), and is comprised of the main embankment starting on the left abutment of about 1,500 ft (457 m) heading to the Northeast, followed by the terrace embankment of 4,800 ft (1,463 m) heading to the North. An upstream impervious blanket extends up to 500 ft (152 m) upstream of the dam along the majority of its length. The outlet works are to the left of the embankment, and consist of an intake structure with six gates, followed by two outlet conduits that finish in a stilling basin. To the left of the outlet works is the uncontrolled emergency spillway, which was doubled in width to 540 ft (165 m) in 1989, and excavated material utilized for construction of a stability berm against the upstream face of the main embankment. A concrete parapet wall was also installed along the upstream side of the crest during this work. In 1982, a toe drain, downstream filter berm and line of 35 relief wells were installed. The filter berm was recently extended an additional 200 ft (61.0 m) downstream and granular filters were placed over an approximate 2000 linear ft (610 m) reach of the lower terrace slope. (Fig. 3)."

Jan 1, 2016

By Sara Moshfeghi, Seyyed Majdeddin Mir Mohammad Hosseini, Abolfazl Eslami

"Due to variety of current pile bearing capacity methods based on the cone penetration test (CPT), for optimum design, it is necessary to evaluate the performance of such methods in different geotechnical conditions. Geotechnical databases including piling and in-situ testing records have been recognized as useful tools for analysis, design and economical construction. In order to evaluate pile bearing capacity methods, AUT-CPT&Pile database has been compiled including 450 full scale pile load tests and CPT sounding records. This database consists of different pile types with a relatively wide range of geometries and various soil conditions. Forty three records of piles driven in sand deposits were then employed to evaluate effects of ultimate capacity interpretation criteria from load displacement diagrams. The Davisson offset limit criterion, the Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter were compared to estimated capacities from ten CPT based design methods currently used in practice. The Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter lead to reasonable results, the Brinch Hansen 80% criterion showed less scatter. For evaluating the accuracy and the precision of CPT-based methods, the results were compared to estimated capacities. Results of comparison indicate that the CPT-based methods mainly predict the pile capacity withreasonable accuracy.INTRODUCTIONAmong the different approaches of estimating the pile bearing capacity, in-situ tests, especially, the cone penetration test (CPT) are favored due to the cone similarities with piles in modes of installation as well as fast and continuous profiling. This trend is practically well established where deep foundations are to be constructed in soft to medium subsoil deposits (Eslami and Fellenius, 1997; Mayne and Niazi, 2009).Employing different design methods results in a wide range of values which complicates the selection of an appropriate one to determine the pile bearing capacity. Several studies by Briuad and Tucker (1988), Eslami and Fellenius (1997), Abu Farsakh and Titi (2004), Schneider et al. (2008) and Eslami et al. (2011) confirm disparity of different design methods predictions. Thus, for optimum design, it is necessary to evaluate and compare the performance of current methods.Geotechnical databases are known as helpful tools in research and practical applications for optimizing analysis and design and are mainly used for management and interpretation of data, evaluation of design methods, calibrating LRFD or ASD design factors, etc. Pile lateral and axial load tests are examples of databases in geotechnical engineering. A summary of several CPT and pile load test databases is presented in Table 1."

Jan 1, 2017

By Takefumi Takuma, Masashi Nagano, Christopher DellAringa

Multiple agencies in Southern California are retrofitting and upgrading their levees to catch up with ever-advancing urbanization affecting the requirements for existing channels and levees in this seismically active zone. Pressed-in sheet piles have been specified on some of these projects to minimize noise and vibration problems associated with sheet pile installation. This paper will study three Southern California levee and sewer pipeline retrofit projects that utilized pressed-in sheet piles in hard soil conditions with N-values higher than 50. BACKGROUND Southern California is home to numerous drainage channels fortified with earthen levees. In spite of the region’s semi-arid climate with varying annual precipitation from year to year, winter storms can bring in heavy and continuous rainfall to the area which overwhelms the levees’ capacities at times. Some levees are running through densely populated areas with homes and other sensitive structures such as underground utilities and bridge piers. Conventional sheet pile driving utilizes either percussive or vibratory pile driving methods, both of which generate high levels of noise and vibration, causing nuisance and potential damage to nearby structures. On the other hand, the press-in piling method utilizes a hydraulic force to push piles into the ground, thus practically eliminating the noise and vibration issue. Although there are types of press-in piling systems mounted on tall leaders on large crawler-base machines, they are less frequently used due to its much larger size and more limited drivability than the type discussed hereunder. The other type of press-in machine sits on top of already installed piles and is anchored with its own weight and additional counter weight when starting off as shown in Figure 1. Once the first few piles are pressed in, the equipment grips on top of the installed piles and moves forward on its own as the pile installation progresses. See Figure 2. This method does not use a vibratory or percussive force to install piles.

Jan 1, 2018