Search Documents

By Dominique Vié

Standards methods covers the procedures for testing deep foundation to determine the force and velocity response to an impact of a pile driving hammer or similar device. The results of analysis generally include an assessment of pile integrity and the value of maximum dynamic stresses. But evaluation of static bearing capacity remains a matter of individual engineering judgment. A new 1D finite elements model has been developed for dynamic stresses and velocity analysis. Following an international benchmark of bearing capacity prediction organised by the Belgium Building Research Institute (BBRI), 12 piles in a site of fissured stiff tertiary clay tested in 1999, and 12 piles in a site of dense sand tested in 2001, comparison are proposed between analysis of dynamic tests and static tests results. A procedure is proposed to take in account the results of dynamic test for evaluation of bearing capacity.

Jan 1, 2002

By A. Verghese Chummar

The paper presents a field study where the effect of negative drag caused the failure of a pile foundation system. Utilising the field observations the probable negative drag that acted on the piles is worked which gives an insight into the effect of negative drag on deep foundations.

Jan 1, 1996

"Boston’s Central Artery passes beneath nine active railroad tracks carrying commuter and Amtrak trains into South Station, the City's busiest rail terminal. These railroad operations had to remain in service throughout the construction of the “Big Dig”. The solution was to jack the tunnel under the tracks, rather than build the tunnel by more conventional means.Jacking of utility pipes is fairly common, but jacking boxes as big as a highway had never been done in North America, until the Big Dig came along.Soil freezing was decided upon as a means of stabilizing the soil under the tracks. This allows the tunnels to be jacked into place without soil caving when the soil is excavated at the leading face of the advancing tunnel boxes. Hundreds of pipes were driven into the ground between the tracks. Inside the steel pipes were smaller plastic pipes. A freezing plant near the railroad tracks pumped refrigerated brine into the inner plastic pipes. The brine ran out the bottom of the inner pipe, flowed up to the top inside the outer pipe, and was re-circulated to the freezing plant and back again into the ground. Over several weeks the circulating brine drew the heat out of the soil little by little, and froze the ground outward from the pipes. Soil FreezingThe plan required the construction of jacking pits in which the tunnel boxes could be constructed, and from which they could be jacked forward to their final locations, as described in the accompanying article. Once the jacking pit was built and the tunnel box constructed inside the pit, crews made an opening in the headwall of the pit to allow passage of the tunnel sections, excavated about three feet of the frozen soil, pushed the tunnel box ahead, and repeated the procedure again and again."

Jan 1, 2003

By J. -M. Rescoussier

Due to Important settlements inducing major structural damages, the western part of the Grand Littoral shopping centre has been closed in 1997. The present paper describes the project of underpinning including not only micropiles under the structure of the building but also a reinforcement of the soil located between the shopping centre and the edge of the embankment surrounding the western part of the shopping centre. The aim of this reinforcement is to reduce existing horizontal movements to allowable values.

Jan 1, 2002

By Makoto Kimura

Failure tests on laterally loaded single and pile group are analyzed with a 3-dimensional elasto-plastic finite element program. In the analysis, the mechanical behavior of the ground is supposed to be elasto-perfect plastic with Drucker-Prager's yielding criterion. The nonlinearity of the piles is simulated by assuming a hyperbolic relation between the bending moment and the curvature of the piles. The influence of the axial stress on the cast-in-place concrete piles is also considered in the numerical analysis. It is found that the mechanical behavior of the piles subjected to lateral loading, such as the load-displacement relation up to an ultimately large deformation, and the distribution of bending moment in the pile group can be well simulated.

Jan 1, 1996

By Bernardo J. Jiménez Vega, Edy L. T. Montalvan

Rammed stone columns and similar reinforcement systems are used worldwide more frequently as a cost-effective method for improvement of foundations on soft soils. The effectiveness of the treatment method is evidenced by the increase in bearing capacity and reduction of compressibility of the treated ground. In this study, two job sites with over 500 stone columns were studied. On both jobs sites, shallow soft silty soils were found and stone columns were designed to support the foundations of MSE walls, which serve as abutments for viaducts. In order to verify the soil improvement efficiency CPT tests were performed before and after the construction of stone columns, also plate load tests were performed on both job sites to verify the deformation modulus of the stone columns. From CPT data it was observed an increase up to 30% of sleeve friction and 20% of tip resistance, which demonstrated a higher deformation modulus maintaining the same strength in the soil after stone columns construction. The plate load tests yield load-deformation curves which indicated that the original assumed modulus was conservative. As a result of these findings, optimization of the settlement reduction ratios was conducted using the modified values of deformation modulus for the soil and stone column, obtaining a reduction up to 30% of stone columns for further job sites with similar soil conditions.

Sep 8, 2021

By S. X. Liang

In China, the bearing capacity predictions of the pile with Stress-Wave Theory have been developed rapidly in recent years. This paper recommended a DZH-3 Pile Driving Analyzer and its relevant computer programs. Taking Qinghai Hotel Project for example, it gave their applications in the dynamic tests of large diameter cast-in-place piles.

Jan 1, 2010

By D. E. Sherwood

Recent developments in high torque hydraulic rotary rigs has lead to the construction of secant bored pile walls by rotary drilling methods in circumstances where earlier methods were difficult and in some cases impossible. The evolution of secant bored pile wall construction is described including classical, rotary drilled and continuous flight auger construction methods. The paper then details the restraints which have been created in recent inner city redevelopment, many of which were not relevant in the early days of the technique. Typical examples of walls are presented to show the adapatability and advantages of the secant bored pile wall method. A number of in-situ retaining wall construction techniques are then compared in detail with regard to relative cost, technical quality and practicality.

Jan 1, 1989

By B. N. Hira

A multistoreyed residential complex was at the penultimate stage of construction by ONGC at Nazira, Assam. The site was situated at high earthquake zone. The subsoil was very weak and contained soft to medium clay with water table almost at the ground level. The bearing capacity of soil was quite poor particularly with predicted settlement beyond permissible limit. In this situation, the conventional shallow and deep foundations were found uneconomical and ground improvement with granular piles was considered as the viable solution. ONGC approached the Central Building Research Institute with the request to design granular piles along with R.C.C. foundation and other suitable cost effective measures. CBRI collected relevant geotechnical informations and supplimented the data by conducting field tests at site and laboratory tests at Roorkee. Rational design of 30 cm dia. and 5.00 meter deep granular piles were suggested with isolated and combined RCC footings over the reinforced soil. In addition to several structural and geotechnical advantages, the granular pile foundation provided considerable economy in the cost of construction. The paper presents the salient geotechnical and structural informations of the challenging project and provides the design details of the innovative granular pile-system. It also furnishes the design approach of the RC footings and other elements of the foundation.

Jan 1, 1996

By B. M. Das

Laboratory model test results for the ultimate uplift capacity of rough rigid single and group piles embedded in sand have been presented. Model tests on single piles were conducted in loose, medium, and dense sand. The uplift tests on group piles were conducted in medium sand only. Based on the present model test results, tentative relationships for the estimation of the ultimate uplift capacity of single pile have been presented. The efficiency of group piles is a function of the length-to-diameter ratio, center-to-center spacing to diameter ratio, number of piles in a group, and the degree of compaction of sand.

Jan 1, 1989

By Zia Zafir

Design of the deep foundations for the loads imposed by lateral spread include the estimate of the pressure applied by the liquefied material as well as amount of anticipated displacement. In the absence of a non-liquefiable cover over a liquefiable layer, it is possible to design the foundation system just for the additional pressure applied by the flow slides. On the other hand, if a non-liquefiable layer exists above the liquefied zone, the foundation should be designed for anticipated movements. To completely account for liquefaction and/or lateral spread and their interaction with the deep foundation system, a coupled soil-structure interaction (SSI) analysis should be performed. However, a complete SSI analysis may not be feasible for most of the projects. This paper will present recent advances in analysis techniques and simplified methods to design deep foundations for liquefaction and lateral spreading. In addition, a case history of the Rancho California Bridge in southern California located within 1 km of the active Elsinore fault will be presented. One of the bridge abutments is underlain by potentially liquefiable layers. The pressure applied by the liquefiable layer was estimated to be greater than the shear capacity of the 36-inch CIDH piles designed for the abutment. However, with limited ground improvement and more careful analyses incorporating structural effects of CIDH piles, resulting design and construction resulted in a factor of safety greater than 1 against slope failure. The recommended approach was generally consistent with the recently published, and AASHTO sponsored, NCHRP 12-49 project regarding seismic design guidelines for new bridges and the effects of seismic displacements against bridge foundations.

Jan 1, 2006

By A. David Miller, Douglas M. Barber

"The Rocky Mountain Arsenal was used by the military to produce chemical warfare agents and incendiary munitions for use during World War II and later by private companies for the production of industrial and agricultural chemicals. After an investigation performed in accordance with CERCLA confirmed significant levels of contamination due to the common industrial and waste disposal practices of the era and the discovery of over 300 species of wildlife inhabiting the land the Rocky Mountain Arsenal became a wildlife refuge and contamination cleanup efforts began. Three lime basins originally used to treat wastewater from the chemical production were decided to be contained in place, requiring a seepage barrier installed around the perimeter of the site to further prevent groundwater/contaminant migration. This case study will discuss the successful installation of a soil-bentonite cutoff wall around the area using deep soil mixing. Highlights of this case study will also include a discussion of the challenges faced due to construction activities performed with Level B Hazmat PPE requirements as well as added challenges brought on by the Winter season, after the project was delayed due to a positive air monitor detection for the chemical weapon Lewisite during construction of the work pad.INTRODUCTIONThe Rocky Mountain Arsenal (RMA), located just outside of Denver, Colorado, was established by the United States Army in 1942 to produce chemical warfare agents and incendiary munitions for use during World War II. Following the war, and as weapons production decreased, portions of the site were leased to private companies for the production of industrial and agricultural chemicals. The principal lessee, Shell Oil Company, manufactured mostly pesticides at RMA facilities from the early 1950s to the early 1980s.In 1984 an investigation began in accordance with the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) and confirmed significant levels of contamination due, in large part, to the common industrial and waste disposal practices of the era. It was also discovered that over 300 species of wildlife inhabited the land in the absence of regular human activity, including a group of bald eagles, leading to the passing of the Rocky Mountain Arsenal National Wildlife Refuge Act in 1992."

Jan 1, 2015

By Stephen Buttling

The construction of a water treatment plant in Dandenong, Victoria, required detention tanks and a pumping well. The design provided by the Engineer used conventional rectangular cast-in-situ reinforced concrete walls within a sheet piled cofferdam. It was decided to construct the tank and shaft using the diaphragm walling technique as an alternative and, for the shaft in particular, this involved a “circular wall”. Except where cutters are used, joints in diaphragm walls have to be made between colinear panels, with waterproofing provided by dumb-bell water stops held within trapezoidal forms. This means that the circle has to be approximated by a number of straight sides, which in this case was twelve. The requirement was to design the reinforcement for the strange shaped panels. Finite element analysis was used, in the first stage using an axisymmetric model to determine the profile of lateral earth pressures with depth. In the second stage a horizontal slice was modelled, without gravity which normally operates from the top to the bottom of the page. By considering appropriate possible earth pressures at different depths, a range of bending moments was calculated, which was used by the structural engineers to design the rebar. The tanks were successfully constructed, and inclinometers were installed in both the tank and the shaft. Measured deflection profiles show that the design was moderately conservative.

Nov 1, 2022

By Dean Abbondanza

"Below grade foundation design has construction issues that above grade foundations do not. These cost factors are dependent on soil conditions and vary by region, but for the most part, the process remains standard.An innovative design concept using steel sheet piles as the permanent wall element changes the traditional cost and schedule for below grade foundations. The sheet pile application reduces dewatering requirements, does not require waterproofing on the vertical walls and eliminates the cast in place concrete wall structure.Foremost, this versatile application affords both Contractor and Designer the choice of two methods of construction; conventional bottom up or top down. The top down method not only provides the savings of bottom up, but also eliminates the cost of anchors while taking the foundation out of the critical path in the early stages of construction. CONVENTIONAL FOUNDATIONSINTRODUCTIONUS construction for a conventional below grade (BG) foundation is fairly standard. Design and install the shoring system, followed by dewatering (if groundwater is present), then excavate in stages with installation of anchorage as work proceeds to final elevation. The site is graded for a waterproofing system to be placed at the base. Once the base slab is cast; forms are set for the vertical reinforced walls. After curing , waterproofing is applied to the back side. The remaining levels are constructed until ground elevation is reached. The site is backfilled and the ground floor is cast. The foundation is now complete and work on the superstructure can now begin."

Jan 1, 2005

By Shawna Munn, Carol Dounitch, Erika Acton

The EQ Bank Tower, a 24-storey office tower with 4 levels of underground parking, is currently under construction at 25 Ontario Street in the downtown core of Toronto, Canada. The tower geometry required an 18 m (60 ft) deep excavation inside an existing 3-storey 100-year-old façade, to be retained in place throughout construction. This presented a variety of design challenges that required several innovations and a customized monitoring program. In this paper, we will discuss two major challenges, and highlight the innovative and adaptable solutions carried out using performance-based design leveraging the observational method. The first was installation of a shoring system in a 500 mm (20 in) gap between the historical façade and a live gas main. The second involved excavating 10 m (33 ft) into expansive shale bedrock adjacent to a sensitive neighbouring building.

Oct 1, 2022

The process of pile driving disturbs the soil around the pile. The nature and magnitude of disturbance depends upon 1) the pile size, and 2) the nature of soil. Therefore, the prediction of a single pile behavior based on soil properties of undisturbed soil samples may not match its performance. Under lateral loads, the pile may loose contact with the soil near the ground surface especially in clays. The soil pile interactions are influenced the most by pile behavior in this zone. This situation further affects the tally of prediction and performance. Piles are used in groups. The zones of overlapping stress from one pile to the other both around the pile and below their tip particularly in soft soils, contribute to group effects. Empirical solutions have been developed for prediction of the pile group behavior. The group action is more involved under vibrations. Several cases of single piles and pile groups under static and dynamic loads from published records have been analysed. It has been shown that single pile test is the best source of information on the soil-pile-soil interaction effects.

Jan 1, 1989

By D. A. Bruce

The Deep Mixing Method is a very valuable tool for combating problems related to in situ soil treatment, improvement, and retention. Many different variations are used throughout the world, and there is a correspondingly rich technical literature on the testing and properties of the treated soil. This paper provides a synopsis of these aspects.

Jan 1, 2001

1.1 The parties agree to submit all claims, disputes or controversies arising out of, or in relation to, the interpretation, application or enforcement of this agreement, including dispute resolution procedures, to sequential mandatory discussion, mediation and arbitration for resolution of all disputes before, and as a condition precedent, to self-help, arbitration, judicial action or other remedies. This mandatory procedure will resolve each dispute within one-hundred (100) calendar days. Any deadline falling on a federal holiday or weekend will be the next working day. Breach of this disputes process shall constitute a material breach of contract for which the aggrieved party may recover all costs, including attorneys fees, interest and other expenses necessary to resolve the dispute through litigation. The obligation to discuss and then mediate and arbitrate covers all disputes arising from every aspect of the Project to be built by the owner, including, but not limited to, design, engineering, bonding, indemnification, labor, material and services, and the acts or omissions of any related party for whom a party to this agreement may stand responsible.

Jan 1, 1994

By Zhang Baoshan

In this paper, the forced features and dynamic behaviors of stone-column composite foundation are concisely related. The characteristics of Rayleigh wave method is summarised. This method is proposed in which, the stress ratio of the stone-column to the surrounding soil and the bear­ing capacity of the composite foundation are determined. Through the engineering cases, it is shown that, checking and evaluating the composite foundation in this method, is feasible, with high speed and low cost.

Jan 1, 1991

By P. V. Chandramohan

"In ports, piled berths are designed and constructed for berthing of ships with a finite draught. Piles in a bridge foundation also have a large free stand above scoured level. The piles of these structures have to withstand large horizontal forces imparted by the impact of the approaching vessels or due to longitudinal and transverse action in a bridge. It is also imperative that these piles have to project out of the dredged / scoured bed. These piles are normally designed as slender compression members subjected to bending also. They are subjected to vertical load tests for assessing the soil resistance. Lateral load tests, as a rule, are also stipulated. IS and IRC codes stipulate a deflection criteria for lateral load test to arrive at the capacity. These tests are usually conducted on a working pile by jacking out two piles. At the time of the test, pile will be free headed. But in service, piles are fixed head. There is a large difference in deflections between a fixed head and a free headed pile. Besides, a free headed pile will be subjected to a much higher bending moment than the fixed head one. This will put the working test pile under risk of breaking during the test. The problem is analyzed with case studies. INTRODUCTION Vertical capacity of piles is assessed by static formulae. This formula is based on the soil properties obtained from random soil exploration and laboratory and in-situ testing. Since soil is not a homogeneous medium, properties can vary. The design parameters taken for computations may be different from the ones at the interface of the pile with the soil. The best way is to find out is by a load test. The code IRC:78-2014 has rightly stated that initial load test is part of the design process. This is true with the vertical load test. But there are certain problems with the purpose and inference of the lateral load test. In both the tests the criteria for acceptance is the quantum of movement of the point of application of the load. In the former, the movement is vertical and depends more on the compression of the soil than the compressive strain in concrete. But in the latter, this movement is partly on account of the flexural rigidity of the pile and partly due to the horizontal compressibility of the soil. The role of rigidity of the pile is more when compressibility of the soil is higher. Lateral load test is done by jacking one pile against another because it is difficult to get an independent horizontal reaction. Please see Fig.1 Photo."

Jan 1, 2015