Search Documents

"1.0 INTRODUCTIONThese Guidelines reflect the state-of-the-practice of the Deep Mixing Method (DMM) in North America. DMM is an in situ mixing process that breaks down the soil structure; injects binders, fillers and reagents into the soil; and blends them with the soil. DMM is also commonly referred to as Soil Mixing. The final properties of the treated soil in situ are a function of the composition of the native soils and groundwater, the binders introduced, the mixing methods and energy, and the conditions and time of curing. Treated soils generally have increased strength and stiffness and/or reduced permeability relative to the native soils.This document addresses DMM performed by rotating single and multiple axis mixing tools, rotating cutter wheels at the end of a rigid kelly bar, or trench mixing using a rotating cutting/mixing chain around the perimeter of a rigid bar. Binder may be injected through low or high energy (velocity) jets.The treated soils created through wet DMM are heterogeneous mixtures of binder, water, soil, and groundwater. Treated soils produced by dry DMM techniques are a mixture of binder, soil, and the water already present in the native soil.DMM applications described in this document include•,Earth retention•,Liquefaction mitigation•,Groundwater seepage control and containment isolation•,Bearing capacity improvement•,Deep foundations•,Mass stabilization and contamination containment•,Embankment, levee and dam strengthening, and stabilization•,Casing replacementThis document was developed to address deep foundations applications. Use of deep mixing for seepage control is not specifically addressed. The reader is referred to documents prepared by the U.S. Army Corps of Engineers for additional information. Shallow soil mixing and the use of DMM for stabilization/solidification of contaminated soils performed at depths less than 10 feet (3 m) are mentioned briefly. Jet grouting is not covered by these guidelines."

Jan 1, 2016

By Mary Ellen Bruce

Let me first address the issue of the wet grab samples. The wet grab samples that were attempted to take on the Central Artery were hindered by the fact that the way the mixing was being done was only by injecting grout on the way out, during withdrawal of the mixing tools. They would auger down to the required depth (usually with some water being injected), which took anywhere from 45 minutes to an hour, and then when coming out, the grout would be injected with grout. That was leaving a column of grout in the center where the shaft had been (i.e. inside of the blades of the mixing tools), which would end up being something like a foot in diameter because the pipe that was used for the drill shaft was a foot in diameter. So we had 10 inches to a foot of almost pure grout in the middle of our column and then we had 2 feet on either side that was mixed soil cement. So when they went down with the wet grab sampler not knowing where that was in the column sometimes they/we were getting strengths of 1500 psi, and sometimes they/we were getting strength of 500 psi or 100 psi. So what was it that we were taking into the wet grab sampler? In those cases you don't really know, but it wasn't representative of the core samples we were taking. We were purposely not coring in the center because we knew that was going to be high cement content, almost pure grout. So the issue of wet grab sampling particularly on this project, the Central Artery Project, was that we didn't really know what we were sampling. What becomes an issue with wet grab sampling in other projects is that you have to have another device (machine) in most cases, a cherry picker crane or something similar that can raise and lower with a beam that is used to forces the sampler down into the freshly mixed soil-cement. And regarding economics, is it more economical to have that crane standing by with its operator or to have a drill rig to come along later and do the coring and take the material out that's fairly identical to what you're finding in situ? The complaint of micro-fracturing in the core samples as you're taking the cores was raised by Seiko as causing large strength reductions. But, if you're doing it carefully, then I don't think that's much of an issue anymore, on research basis perhaps but not on a practical level.

Feb 10, 2003

By Giovanni Lombardi

In order to get a clear overview of the grouting works carried out, to avoid misinterpretations of the data and functions shown on the display of the grout monitoring device, it is recommended to keep the flow rate as constant as possible. Obviously, at the beginning of the process, the flow rate will increase from nil to the selected "basic" value. An important question frequently addressed is also how to reduce the flow rate in nearing the GIN limit so to finally reach the target intensity. Depending on the actual conditions, there are different manners to proceed. However, the following one appears to be the most convenient. It is represented on Figure 25. Being GIN the target intensity, two new limits at, let's say, 0.95 GIN and at 1.05 GIN as shown in the figure should be defined. The selected basic grout flow rate "q0", is kept as constant as possible all along the grouting process until the 0.95 GIN limit is reached. The flow is then reduced step wise to 2/3 q0, 1/3 q0 and zero at crossing each of the three limits. A similar rule can be used in respect to the maximum pressure, while for the maximum volume the process can be stopped at one time. Obviously the number of successive limits and thus the number of steps in reducing the pressure, as well as the width of the fringes defined in said way may be adapted to the local conditions.

Feb 10, 2003

By Franz-Werner Gerressen

"New developments are required day by day. On the one hand site to improve the actual situation, on the other hand site to create the future and to ensure that future demands can be fulfilled. This requires for instance the development of technical support systems, which enable a more constant and quality ensured installation of special foundation products like piles. As part of the quality control, real time installation control of the production process, data transfer and reporting systems become more and more important ensuring the five dimensions of a jobsite. That means not only the three well known dimensions (width, height, depth) are cover, but also the dimension of time and money. Beside small, but important, details, also the demand of extending the use of methodologies in terms of getting deeper or allow their use in various soil conditions require the development of new tools and equipment. Therefore, the paper will describe some of these new approaches and activities required for these new developments. It will describe also the main equipment which will be needed to execute these works under the various conditionsINTRODUCTIONNew developments are required day by day. Either to improve the actual situation, or to create the future and to ensure that future demands can be fulfilled. Therefore, there is an increasing demand for the development of e.g. “Little Helpers”. “Little helpers” are for example technical support systems, which enable a more constant and quality ensured installation of special foundation products like piles, for example an assistance system like the later explained “drilling” assistant. As part of the quality control, real time installation control of the production process, data transfer and reporting systems become more and more important ensuring the five dimensions of a jobsite. In a second part the focus will be given to new approaches for soil mixing application. Adjustments of tools or equipment to extend the range of possible usage as well in terms of soil conditions as in treatment depth.“LITTLE HELPER”GeneralThe B-Tronic System enables you to efficiently operate, maintain, and administer individual machines as well as entire fleets. It helps you to securely monitor and precisely evaluate your projects and work processes. The system is an integrated system for controlling all operations and visualizing actual operating parameters in real-time on a large interactive touch-screen monitor."

Jan 1, 1900

By Akhila Manne, Prasad P. V S R

Storage tanks are heavily loaded thin-shelled structures that exert large loads on and require large foundations to support them. They are generally very sensitive to foundation settlements as it may hinder the performance of tanks resulting in significant commercial or social impacts. Selection of their foundation is dependent on availability of suitable ground and limitations imposed by design specifications. Design of the tank foundations is generally based on theoretical methods and validation by representative field tests. This paper reviews settlement criteria for storage tanks as per national and international standards, case studies of large to medium diameter tanks supported on deep foundation i.e., bored cast-in-situ piles and shallow foundations on improved ground and their performance during load tests & hydro-tests is discussed. Paper concludes that storage tanks can also be supported on shallow foundations resting on improved ground reducing the settlement, time and cost significantly depending on the sub-soil.

Nov 1, 2022

By Greg Canivan, Bernie Hertlein, Les Chernauskas, Joram Amir, Garland Likins, E. Anna Sellountou, Tim Kovacs, Peter Kandaris

Nondestructive testing of drilled shaft foundations via Crosshole Sonic Logging (CSL) is often performed as part of the quality assurance process to assess the soundness of concrete. The intent of CSL testing is to identify irregularities such as soil intrusion, necking, soft bottom, segregation, voids and other defects that could result in poor structural performance of the foundation. Over time, CSL rating criteria based on first arrival time and relative energy have incorrectly evolved to often be the sole means of determining the acceptability of a shaft. Some of these criteria have found their way into regulatory agency specifications, with acceptance values often differing from agency to agency.The purpose of this document is to review the state of the practice (including experience gained over the past 20 years), propose improved CSL rating criteria and make recommendations for additional assessment, as well as educate the industry on the proper interpretation of CSL test. CSL test results alone should not be the sole means of rejecting or accepting a shaft. A task force of industry exerts was formed to review the existing CSL rating criteria and propose improvements where appropriate. The recommendations presented herein are the consensus of the task force, which believes that they should be incorporated into future criteria, codes and specifications. This paper was produced as a joint effort between the Codes and Standards Committee, the Drilled Shafts Committee and Testing and Evaluation Committee. A task force was authorized under Testing and Evaluation Committee. The task force contributed their expertise in web-based discussions often every two weeks over a period of three years. Interested participants were invited to participate at any time. The document had two rounds of broad industry review, two rounds of DFI Technical Advisory Committee reviews, and a Public Comments process. All comments were considered in producing the final document.

Jan 1, 2019

By Quanchen Sun, Mohammed Z. E. B. Elsahife, Anthony Fisher, Chris Barker, Jennifer Schooling

A review of the literature shows that pile integrity is a significant concern in pile construction. Recently, a new integrity test, thermal integrity profiling (TIP,) has been put into use in foundation construction. It measures temperature changes and thermal profiles of concrete during curing. Heat generation and dissipation of early-age concrete is determined by the concrete mix, the ground conditions and the shape of concrete structure. The current data interpretation practice is primary based on experience. Anomaly detection through direct analysis of temperature profiles is currently indicative or suggestive and temperature signatures are usually similar, and numerous causes are not easily isolated. The core of the TIP testing technique, i.e. collecting detailed temperature measurements along the pile during the hydration process, is promising but a new interpretation approach is required. In this paper, a new interpretation approach has been developed in which TIP constitutes the first step. An investigative staged process is then followed to establish and assess the anomalies in the problematic regions along the pile employing the combined use of detailed finite element (FE) simulations, the actual temperature data from TIP and genetic evolution algorithms. In each stage, more details could be revealed about the anomalies being investigated including, ultimately, location, size and shape; this staged process enables practitioners to follow a riskbased approach and decide whether or not to pursue subsequent stages depending on the results they get at the end of each stage. This new approach, depending on the stages required for the analysis, will potentially avail practicing engineers of crucial test results about the quality of the pile immediately following pile construction, hence enabling repair and remedial work straight away at a lower cost.

May 1, 2022

By Brandon M. Robinson, Osman F. Besler, Dominik Gaechter

With the increase in population over the last decade, and anticipated population growth over the coming years, Norway is making significant investments in the Country’s infrastructure. Part of this investment in development starts with the Intercity development project in South-East Norway, which is the largest transport project in Norway. The Intercity Development project consists of 270 km (167 mi.) of new doubletrack rail, capable of train speeds reaching 250 km/h (155 mph). The new stations are centrally located in the major cities, in South-East Norway, to provide the benefit to as many citizens as possible. The goal of the project is to reduce the increase in traffic, which is coupled with an increase in population, and reduce the travel times between the cities. The Intercity Development Project has an anticipated completion date of 2034. The Sandbukta-Moss-Såstad (SMS) project, part of the Intercity development, includes 10 km (6.2 mi) of new double-track railway and is situated on the Østfold Line, near the city of Moss, Norway shown in Fig. 1. The 10 km SMS-section covers three open stretches and two tunnels, including 630 m (2,066 ft) substructure for double-track railways on the open line at Sandbukta. The Moss tunnel is a 1720 m (5,643 ft) long tunnel from Sandbukta to Moss center, including a 420 m (1,378 ft) long concrete culvert. The new Moss station includes an 800 m (2,625 ft) long station area. The Carlberg tunnel is a 2350 m (7,710 ft) long tunnel from Kleberget to Carlberg, including a 200 m (656 ft) long concrete culvert.

Sep 8, 2021

By Carlandrea Albonico, Salvatore Miranda

The paper describes an innovative geotechnical engineering solution that has been provided within the scope of the Galataport Project, in Istanbul, Turkey. Among all interesting geotechnical works included in the Project, this paper presents the design principle, adopted technologies and performance controls related to the Multi- Purpose Bottom Plug (MPBP). This original geotechnical engineering solution has been employed for the deep basement excavation in Karaköy and consists of a combination of seepage control, ground improvement, and load bearing elements, which have been executed with double-fluid jet grouting, pseudo-elliptical jet grouting and permanent micropiles, respectively. The paper highlights the importance of employing cutting-edge technologies within the foundation engineering field and state-of-the-art electronic control devices, in parallel with the essential human expertise, in order to obtain the desired results in this high-profile Project.

Nov 1, 2022

By William G. Ryan, David S. Graham, Dan A. Brown, Rich A. Lamb, Paul J. Axtell

"The St. Croix River Crossing project on the Minnesota-Wisconsin border has been in the process of planning and public debate for two decades, with several changes in alignment. During the course of the earlier planning process in 1995, a drilled shaft load test was performed to obtain preliminary design information. There were some difficulties in maintaining stability within the weak sandstone bearing formation, and the measured axial resistance was relatively low. Subsequent experience by the Minnesota Department of Transportation with similar weak sandstones on the I-35W project suggests that improved construction techniques using modern drilling fluids may offer opportunities for improved performance. During final design in 2012 a second load test program was performed of a full scale test shaft constructed using polymer drilling fluids. The stability of the socket excavation in the weak sandstone appeared to be greatly improved and the measured axial resistance significantly higher.This case history illustrates the excellent performance that drilled shafts can provide in even relatively weak sandstone bedrock as well as the profound influence on axial resistance associated with the construction techniques used. The improved resistance values obtained by the new load test with more recent construction technology allowed the foundation scheme to be substantially optimized with respect to the number and size of required drilled shafts, reducing the size, cost, and risk of the coffercells and footings.IntroductionThe Minnesota Department of Transportation (MnDOT) has awarded the first phase of a bridge construction project that will cross the St. Croix River between Oak Park Heights, MN and St Joseph, WI. The first phase construction contract involves building the river pier substructures including groups of drilled shafts beneath each tower leg. A general location of the bridge project is provided in Figure 1.Prior to award of the construction contract, two separate design-phase axial load tests were performed on non-production drilled shafts with rock sockets. Both tests were static, bottom-up tests using the Osterberg Cell (O-cell). The first test was performed in 1995 when final design and construction was thought to be imminent. After years of public debate and literally, an act of Congress, design of the project was finally restarted and a second load test performed in 2012. The 1995 test was conducted on the Minnesota bank approximately 900 ft southwest of the St. Croix River bank. The 2012 test was conducted in the river about 2,100 ft northeast of the1995 test location. A plan-view of the project indicating the test program locations relative to the bridge alignment is provided in Figure 2."

Jan 1, 2015

By Ian Vaz, Takefumi Takuma, Rafael Holcombe, Chris DellAringa

"This paper will discuss the successful installation of seawalls for the first phase of a project in Long Beach in California known as the Naples Island Permanent Seawall Repair – Phase 1. How an unconventional method of pile driving resulted in the reduction of the duration of the project while using less space and maintaining minimal noise impacts to accommodate neighbors will also be discussed. Included in the paper will be how non-vibratory equipment used on this project also significantly minimized the risk of disturbances as well as settlement on residential properties; which in turn greatly reduced the risk of damage to existing structures. The first phase of a 6-phase project along a section of the canals with tight clearances and proximity to residents included the installation of a 1,912 linear-foot steel sheet pile wall system in front of the existing deteriorating walls from January until March 2015.INTRODUCTIONThis project was located in the Naples Island neighborhood of Long Beach in southern Los Angeles County, California. After 80 years of the same seawall structures lining the canals of this beautiful neighborhood, the City of Long Beach Department of Public Works decided that it was time to better protect the area’s multi-million dollar homes by repairing its crumbling seawalls. The City realized that the walls will only become worse due in part to several concerns, including bending failure for the already deflecting walls. According to the City, certain sections of the walls had a significant risk of global failure if the area experienced a “moderate” near-source earthquake (City of Long Beach, CA, 2014b). Although the seawalls were in need of major repair, this would not be simple. Due to the tight clearances of the seawalls between the homes and canals, installation would be difficult with heavy, conventional construction equipment.Phase 1 of the project involved installing sheet piles on the water side in front of existing and aging vertical concrete seawalls between the Ravenna and Toledo Bridges along the Rivo Alto Canal. See Figure 1 for the General Plan for Phase 1. Financing for this project by the City’s Tidelands Capital Improvement’s Division allowed the construction to begin in a timely manner. However, the challenges for the City included regulatory restraints that further complicated the construction in terms of the duration of the project due in part to numerous regulations from several regulatory agencies."

Jan 1, 2016

By Remco Offenberg, Marcel Bielefeld, Martijn van Delft

The question of the continued suitability of existing foundations arises when the function of the superstructure changes. This can occur when the superstructure is replaced or when the existing structure is expanded, leading to higher loads on the existing foundation. Quite often it is a challenge to define the suitability (with respect to integrity, bearing capacity or both). The lack of information on the existing foundation (such as pile dimensions, installation records, original soil investigation, design calculations, etc.) makes it frequently seemingly impossible to assess whether the foundation or foundation elements can be re-used. The paper outlines the tools available to an engineer to evaluate existing foundation piles for potential re-use. The paper illustrates the application of these tools through a few case studies from The Netherlands, including the evaluation of a 400 years old bridge foundation to address increasing traffic loads.

May 1, 2022

By Joseph A. Mann

"Soil mixing is a proven solution for the construction of ground improvement adjacent to sensitive structures due to the use of computer controlled and monitored equipment. The precision to which geometry is controlled can often be the deciding factor for selection of soil mixing versus other means of ground improvement. Protection of existing structures and utilities requires careful planning, investigation, and may demand supplemental control measures. During planning, it is imperative that the process be fully developed by the project team to ensure proper control measures are budgeted; otherwise, the success and safety of a project can be jeopardized.This paper discusses case histories of soil mixing performed in close proximity to large, sensitive, and critical utilities, including foundation support for an existing earthen dam impounding a water reservoir in upstate NY, a buffer zone for a tunnel drop shaft at an operating wastewater treatment plant in Washington DC, and a containment system to protect a major water line along an interstate widening project in Baltimore, MD. The function of soil mixing as ground improvement varied; however, the selection and application of the technique versus other means of ground improvement was specific due to the controlled manner of construction with soil mixing. Through the three case studies, small diameter (3- ft [0.9 m]), large diameter (8-ft [2.4 m]), and mass mixing applications will be discussed. Furthermore, the case studies offer insight into how the geotechnical community in the Mid-Atlantic utilizes soil mixing technology for widely varying applications. Additional topics of discussion will be the design and construction of the ground improvement systems, procedures and execution of the work to protect existing structures, and the QA/QC methods, procedures, and results from the projects.INTRODUCTIONWet soil mixing, also known as the Deep Mixing Method, is a ground improvement technique that improves the characteristics of weak soils by mechanically mixing them with cementitious binder slurry. To construct columns, a powerful drill advances a mixing tool with radial mixing paddles located near the bottom of the drill string. The binder slurry is pumped through the drill string to the tool as it advances and additional soil mixing is achieved as the tool is withdrawn.Wet soil mixing is applicable in a wide range of soils. Soil mixing has been performed at depths more than 100 lf (30 m). Soils vary widely in their ability to be mixed, depending on the soil type, strength, water content, plasticity, stratigraphy, and texture. Almost any soil type, including organics, can be treated with certain soil mixing technologies, although they may require high binder contents and/or pretreatment to achieve the required results. In cases when the target soil is very soft, including some very weak clays and peats, 100% of the soil may require treatment. This complete coverage of soil mixing is referred to as mass mixing."

Jan 1, 2015

Jan 1, 1996

By Louay Owaidat, Daniel Jabbour, Allan Frappier, Jose Gomez, Mark Stanley, Tino Maestas

The U.S. Army Corps of Engineers (USACE) is implementing a levee strengthening program along the Sacramento River East Levee (SREL) designed to correct 11 miles of deficient levees as identified by recent hydraulic and geotechnical investigations. The first project, the subject of this paper, completed in 2020 resulted in approximately 3.0 miles of improvements to the California Central Valley Flood Protection system. The project area lies along the east bank of the Sacramento River in Sacramento. The program consists of constructing cutoff walls through existing levee embankments to remediate levee through seepage and under-seepage. Key challenges included designing and constructing measures to remediate a 100-year-old legacy levee system, the presence of both industrial and residential properties immediately adjacent to the landside of the levee creating severe space and access limitations, and performing this work during the 2020 statewide mandate to shelter-in-place due to the COVID-19 pandemic. The project team of contractors, USACE, state and local agencies, and engineering firms partnered to bring this project to successful completion within budget and on schedule expending more than 60,000 man-hours with no lost time accidents. With the issuance of future planned contracts, the program will significantly reduce flood risk to the City of Sacramento.

Sep 8, 2021

By Raymond Henn

Yes we have also used some however, again because of the nature of the maintenance window where we have that two hour (at best) window every night and due to the numerous other crews that are wanting to get in to do the other types of maintenance activities, we don't know if we are going to be getting into that same area from one night to the next. So even with the dormancy additives that one can add to cementitious grouts (that are good up to 72 hours) we don't know if we are going to get back in to the same locations from one week to the next. That's why I use the term "the forgiving nature of the acrylamide". It allows us to ream out the hole allowing us to use the exact same hole without having to re-drill a new hole. The program started in 1997 and we have a budget between labor/materials and equipment of 4.5 million dollars on a year to year basis. For the next few years that is going to come down drastically because the program is going to be more of an ongoing maintenance program. The program started in 1997 and we have a budget between labor/materials and equipment of 4.5 million dollars on a year to year basis. For the next few years that is going to come down drastically because the program is going to be more of an ongoing maintenance program. Up to the end of 2001 we were just over 1.7 million liters of between AV100 and AV118 grout. Of that, approximately just under 200,000 was AV100 and the remaining balance was AV118.

Feb 10, 2003

By Dave P. DeClerck

Hardman Construction was faced with the challenge of completing a large earth retention project on a constricted downtown Detroit site, while maintaining a safe and productive worksite. To do so, new technologies using robotic equipment was instituted. HISTORY The historic J.L. Hudson Building (Hudson’s) in Detroit, Michigan was the premier retailer in the city’s downtown district from the 1890s through the 1960s. The massive flagship store sat at 1206 Woodward Avenue, one of the busiest streets in the Detroit area. Hudson’s broke ground in 1891 and would go through twelve renovations and expansions. The last renovations took place in 1946, which gave the building the title of being the largest department store in the world at the time. It spanned an entire city block and boasted 2.2 million square feet of retail space. By the 1970s, Detroit was in an economic downturn. The Hudson’s department store finally closed its doors in 1983. Besides a few working offices, the building sat vacant. The building was unique in that it had four levels underground, offices, mechanical areas, and equipment storage. Following years of neglect, the Hudson’s building was seized by the state and transferred into the hands of the city. The city had it demolished in 1998, (shown in Fig. 1) to construct a new, four- level underground parking garage as well as a potential future above-grade development (Sewlck, 2017). The building was imploded in one of the largest implosions of that time. The building rubble filled the underground rooms and helped to stabilize the exterior concrete walls and keep them from collapsing.

Jan 1, 2019

By Ihab Allam PE, Meeok Kim. PE. Ph. D

The wet weather equalization basin (EB) planned for Pacifica, CA is a 45 feet deep rectangular shaped underground water tank containing over 2.1 million gallons of water, and located only 500 feet away from the Pacific Ocean. The location and size of the water tank, and the geotechnical characteristics of the selected site presented many engineering and construction challenges. The engineering had to consider a structural system which can fit into the limited area of the site and yet need to meet the storage volume requirement. In addition, the system construction should meet the city’s tight budget and schedule.

By R. K. Filip

"Steel bearing piles have long been used to carry high compressive, tensile and lateral loads. Such piles are most commonly tubular or ""H"" profile and are typically installed using percussive techniques. The noise and vibration associated with such installation techniques tends to preclude the use of steel bearing piles in urban and other sensitive areas.This paper describes the design and construction of an innovative new road bridge in Milton Keynes, UK. The steel bearing piles were required to continue out of the ground to form the bridge columns and abutments and then be cast directly into the soffit of the reinforced concrete bridge deck. This project was to be the first time in the UK, that this form of bridge design had been used.The paper shows how new installation techniques allowed the designers to use these high capacity steel elements in a sensitive urban environment without the use of percussive or vibratory installation techniques. Finally the paper shows how these quiet and vibration-less installation techniques can be extended to other applications.A UNIQUE BRIDGE SUPPORTED ON ""BOXED SHEET PILES""CONCEPT HISTORYThere are over 700 bridges in Milton Keynes. Concrete is the dominant construction material, most are single span with massive parallel wing wall retaining abutments. All have a certain uniformity of aesthetic design. Pell Frischmann Consultants Ltd (PFC) proposed to the client, English Partnerships (EP), that an ""integral bridge"" with a slender open appearance would be an appropriate aesthetic form for a new highways bridge, within the district of Westcroft (figure 1). The concept required that the bearing piles be continued up out of the ground to form the bridge columns and abutments. Four rows with four piles in each row were suggested. Each would then be cast directly into the reinforced concrete bridge deck forming a moment connection (figure 2). This concept meant that a single continuous steel structural member would replace traditional reinforced concrete bored piles, pile caps and piers. This member would carry vertical and lateral loads. The conceptual design was intended to meet the following client requirements:"

Jan 1, 2005

By David Guy, John Stanbury, Gilbert Tallard

"In 2009, storm surge from Hurricane Sandy inundated the Bay Park Sewage Treatment Plant located at El. +4 to +12 (+1.2 to +3.6 m) in East Rockaway, Long Island, NY. With all systems down, raw sewage water mixed in the floodwaters. A recurrence of such an event being unacceptable, and in view of rising future sea levels, a flood protection project was developed by Nassau County with funding coming in large part from the federally funded Sandy Rescue Fund. Designed by Arcadis/Hazen & Sawyer Engineers J.V., the protection took the form of a perimeter barrier capable of withstanding future storm surge. Due to limitations imposed by property lines and existing facilities, a levee design with three different types of cross section was developed to adapt to each location, adding construction complexity. The Long Island subsurface is characterized by beach sand extending to great depth. The clay required for the core and levee cover therefore had to be brought in from out of state. A thin silty clay layer at El. -23 to -25 (-7.0 to -7.6 m) served as an aquitard. The under-seepage was reduced by a hanging cut-off wall designed as a vibrated beam thin wall and filled with a salt water resistant, low permeability, self-hardening slurry.INTRODUCTIONOn October 29, 2009, Hurricane Sandy hit New York City, with a devastating effect on the region. The low lying Bay Park Sewage Treatment Plant (STP) (Fig. 1) serving Nassau County on Long Island was submerged (Fig. 2). All basements and underground mechanical facilities were flooded (Fig. 3) and millions gallons of effluent were released into the waters of the nearby Hewlett Bay which connects via other small waterways to the Atlantic Ocean."

Jan 1, 2016