Search Documents

By P. Srinivasulu

The popular theoretical models used for assessing the dynamic behaviour of piles under vertical and lateral excitations are critically reviewed. An experimental study is presented on model piles with varying slenderness ratios. The theoretically evaluated and experimentally deduced natural frequencies and resonant amplitudes of the test pile-soil system are compared. The dynamic stiffness and damping are seen to increase with increasing slenderness of piles. Further, the damping yielded by the theory is found to be on the unconservative side.

Jan 1, 1996

By Garland Likins

High strain PDA testing has become common for verification of capacity of both driven and bored piles. It is equally applicable to Augered-Cast-in-Place (ACIP) Piles. It also evaluates other aspects of the installation such as integrity. The benefit of high strain dynamic test results for the relatively low cost of the tests compared to conventional static testing has resulted in widespread use. The method is described and specific procedures for testing ACIP piles are outlined. Example results demonstrate the application.

Jan 1, 2000

By George Piscsalko

"Quality control of drilled shafts and CFA piles is greatly dependent upon the practices of the site personnel. In many applications it is difficult or not possible to fully inspect the shaft prior to concreting, such as when the shaft is drilled under slurry. CFA piles are cast with no ability to inspect the shaft prior to concreting. There are numerous methods currently available to assess the integrity of drilled shafts and CFA piles. This paper will compare evaluations by three existing non-destructive test (NDT) methods with a new method of Thermal Integrity Profiling for assessing integrity in drilled shafts and CFA piles. This Thermal Integrity Profiling method determines the integrity over 100% of the shaft cross section, both inside and outside the reinforcing cage, by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements are made typically only 12 to 48 hours after concrete placement, thus accelerating the construction process. Thermal Integrity Profiling will be described in detail and the Thermal Integrity Profile (TIP) results from several shafts with purpose built defects will be discussed along with several case histories from drilled shafts and CFA piles where Thermal Integrity Profiling was used. The case histories will compare TIP with various other NDT tests utilized on these particular piles including comparisons with Low Strain Integrity Testing and Cross Hole Sonic Logging. Test results for the various methods will be discussed and the excavation of the upper portion of one drilled shaft will be shown and discussed. IntroductionDrilled shafts can be a desirable foundation element in many applications due to the large axial and lateral capacities which are attainable for very large drilled shafts. Drilled shafts can be cast in a dry hole which allows for inspection of the hole prior to casting, but the casting process is very difficult to nearly impossible to inspect with any accuracy. Drilled shafts are frequently cast under slurry as a means to stabilize the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to accurately inspect the hole prior to casting and it is equally difficult to inspect the shaft during the casting process. CFA piles are another popular choice for their relative ease and speed of installation. The trend has been larger CFA piles carrying greater loads, which makes quality control critical for these piles. Many of the above mentioned processes are blind to inspection and therefore the chances increase for having defects present in the completed elements."

Jan 1, 2014

By Fred C. Schmednecht

For years, the strategy was to contain waste and in many applications, is still the recommended method. Recently, it has become acceptable to create filters below ground for the in-situ treatment of waste. Consequently, in lieu of the waste being contained, it is desirable that the waste flow through a pervious treatment zone. For instance, subterranean pervious walls comprised of iron sand are particularly useful in treating chlorinated solvents in contaminated groundwater. The iron acts as a corrective filter to treat the contaminated groundwater. How are these impervious and pervious walls being constructed? One effective means of constructing an impervious barrier is the vibrated beam method. This method, in brief, involves the use of a fabricated steel beam, a vibrator, a pile driving crane, and a mixing plant. This method results in a 4-6" wide wall with depths up to and exceeding 100'. Over one hundred slurry walls have been installed using this method in the United States. The need for the vibrated beam method continues to escalate due to its reduced health and safety considerations, high level of quality control, lack of excavation, narrow working area, and ability to achieve depths greater than 100'. A recent project was in Marinette, Wisconsin at the ANSUL facility. The project consisted of a 28,000 square foot slurry wall and was completed in January of 1999. Another effective means of creating an impervious barrier, where structural support from the barrier is needed, is the Waterloo® Barrier System. This system involves the use of a pile driving crane, Waterloo® steel sheet piles which are patented steel sheet piles due to their groutable interlocks, and a grout plant. This system results in a water-tight barrier due to the grouted interlocks and provides structural support. A project was completed at Beta Steel in Portage, IN for a retention pond to protect Lake Michigan. Due to the new concept of "filtering", there are few accepted construction techniques available. One effective field proven construction technique is the patent pending mandrel emplacement technique. This technique involves the use of a fabricated hollow steel mandrel with a shoe, a vibrator, a heavy duty crane, and a material feeder. This technique results in a pervious wall which may be comprised of pure iron sand or any other flowable media. Using this technique, the pervious wall may be constructed in varying widths to depths in excess of 100'. A successful installation occurred in October 1997 at Cape Canaveral Air Station in Florida.

Jan 1, 1999

By Willie M. NeSmith

In the Metropolitan Atlanta Area today, augered, cast-in-place (ACIP) piles will be considered on most projects where deep foundation support is required. ACIP piles were first used in Atlanta in the late 1960s, and application began to blossom in the mid-1980s. Current design practice for ACIP piles is addressed in another paper in this conference. This paper describes the evolution of the ACIP industry in Atlanta, and details the use of ACIP piles on major projects in the Atlanta area.

Jan 1, 2003

By Alp Gokalp

The aim of this article is to present an application of jet grouting technique in stiff clays for foundations of the natural gas combined cycle power plant, under construction in Aliaga, Turkey. The plant site is in the Aegean coastal region and 60 km north of Izmir. The foundation soil is composed of quaternary alluviums on top and tuff base rock. The thickness of the alluvium varies between 16 m to 30 m. Groundwater was observed 2.5 m below the ground level. At the design stage, settlement analyses were carried out for the various buildings and facilities in the power plant. Based on the analyses, it was predicted that total and differential settlements are not tolerable, thus jet grouting is implemented as a ground improvement under the majority of the foundations of the power plant. This paper also describes the selection of jet grouting technique, application type and details of the process parameters such as injection pressure, number and size of nozzles, lifting and rotation speeds. Prior to the commencement of the jet grouting works, a number of preliminary parameter tests and preliminary pull-out tests were carried out throughout the site in order to define and verify the jet grouting process parameters to achieve the required diameter of 600 mm and minimum jet grout strength of 3.2 MPa. Moreover as part of the comprehensive quality control and quality assurance program pursued in the project, a number of tests; such as continuous coring, integrity testing, installation of confirmatory jet grout columns, were carried out during the production of jet grout columns.

Jan 1, 2002

By Charles H. Dowding

Whenever piling vibrations are significant, construction activities associated with pile driving and/or excavation can produce permanent displacement. These permanent displacements are more detrimental to structural performance than the hair sized, cosmetic, plaster cracks that might be produced by slightly exceeding reasonable vibration controls. Case studies are presented which demonstrate the relative importance of permanent displacements compared to directly produced transient vibration displacement within a horizontal distance of one pile length. Special attention is paid to settlements produced by densification of liquefiable sands. SOURCES OF TRANSIENT AND PERMANENT DEFORMATION DURING CONSTRUCTION Confusion over multiple sources of facility deformation caused by adjacent construction complicates the discussion of the relative importance of vibration induced cracking. None of the recent scientific investigations of vibration induced cracking (Siskind et el, 1980), involved deformation other than that produced by ground vibration from rock blasting. Thus these studies carry the implicit assumption that no ground deformation occurred other than that produced by the transient vibration. In other words there is no permanent deformation other than that which is typical of the older residential structures investigated.

Jan 1, 1991

By Colin Curtis

The City of Manchester is hosting the 2002 Commonwealth Games. A world class Stadium with a 38,000 capacity was commissioned for a site located close to the City Centre. The Stadium location is in an area that was derelict and in need of regeneration and it is envisaged that the Stadium will be the spur for this. The industrial and residential history of the site has left a legacy of buried foundations together with chemically contaminated soils. This Made Ground deposit overlies Glacial Deposits which in turn overlie bedrocks of the Central Manchester Coalfield. Coal mining has taken place from at least 1761 leaving several worked seams and shafts. In order to support the stadium, 1159 conventional augured piles of 600 to 1200mm diameters were used. This paper will deal primarily with the piling operations and testing, but will also discuss the coal seam treatment with respect to piling. A substantial trial pile test programme was carried out together with 11 static load tests on contract piles. The results of the pile tests will be discussed and conclusions drawn.

Jan 1, 2002

By M. England

A method for the analysis and prediction of single pile displacement behaviour is described. It is the displacement in time, under constant load, based on the use of hyperbolic functions to characterise individual constituents of the displacement-time behaviour. Extensive use of this technique has confirmed its validity in a variety of soils and that consolidation and creep settlement appear to be indistinguishable. The algorithms employed are suitable to model the displacement behaviour from the onset of load to infinite time for all types of piles and surface foundations. Until the advent of computer controlled static load testing, analysis of the displacement-time characteristic during pile load tests has been hindered by the quality of the data recorded and inconsistency of loading. This has hitherto made the development of suitable behavioural models very difficult. Understanding the soil deformation within a proper time framework allows the subject of pile instrumentation and testing to be developed. The equipment required is basically a computer controlled loading and pile head displacement measuring system which allows accurate analysis of the settlement characteristic in almost every situation.

Jan 1, 1993

By C. T. Christensen

The paper gives an outline of the design, installation and performance of a series of mooring and berthing dolphins for a major ferry berth outside the port of Elsinore, Denmark. The Dolphins are large cylindrical bottle shaped and open ended steel piles vibrated into the sandy seabed. They are subsequently equipped with prefabricated fender units. Vehicle access to the ferry is via a fixed ramp and a semi-submerged linkspan. Supplementary passenger access is via a covered gangway steel bridge from an existing gangway facility to a midship door in the ferry«

Jan 1, 1989

By Willie M. NeSmith

Cast-in-place piling are a staple of the deep foundation industry, and are used (in various forms) worldwide. In assessing the application of cast-in-place piles, it is of value to reflect on the development of the various systems, in order to understand how the current processes and equipment came to be. This paper traces the evolution of the cast-in-place industry. Emphasis is on developments in the United States; however, since there has been a substantial fusion of US and European processes, notable European developments are also discussed.

Jan 1, 2006

By Paul Doherty

The offshore wind sector is booming on a global scale, with the U.S. becoming a front runner in this highly progressive market. The Global Wind Energy Council has highlighted the exponential growth in both fixed bottom and floating projects in the years ahead, with global installed capacity set to exceed 300 GW by 2030. This growth in installed capacity is primarily related to fixed bottom projects, which have dominated the market for the past 20 years. However by the tail end of this decade, floating projects are likely to become

Oct 1, 2022

By A. Ghorbani

The analysis of Combined Pile Raft Foundation (CPRF) is very complex due to involved interactions among components of CPRF system. Many researchers made efforts to develop sufficient methods including three dimensional finite element methods to compute these interactions. Since there are some restrictions and complexity in previous methods, in present study a new approach based on three dimensional finite difference methods is implemented to overcome some of these restrictions. The total and differential settlements of a centrifuge case study are computed using different numerical methods to show the performance of present numerical approach.

Jan 1, 2007

By Ramdane Bahar

"Abstract The design foundations can be performed using Menard pressuremeter rules that require a limit pressure and a pressuremeter modulus. In recent years, another trend of interpretation of this test is appeared. It consists of identifying the rheological soil parameters using analytical or numerical methods and then used to evaluate the bearing capacity and settlement of soil foundations using numerical software. This paper deals with the bearing capacity and settlement predictions of bored piles using two approaches. The first one is the method called ""Pressident"" which is a numerical program developed to analyse pressuremeter tests taking into account the Duncan and Chang model. The second approach is the method developed by Bahar and Olivari based on the generalised elastoplastic Prager’s model with the Von Mises criterion which is suitable to describe the behaviour of saturated clays under undrained conditions. The pressuremeter data, collected on various research and consulting projects are used to explore the relationship between limit pressure and undrained shear strength obtained by the two methods. Numerical calculations, by FLAC2D software taking into account the rheological parameters derived from these two methods, are performed in order to predict the behaviour of a single bored pile subjected to an axial vertical load. The predictions are comparedto the measured data.IntroductionThe Menard Pressuremeter test has been used extensively to measure in situ soil properties and for the design deep foundations in Algeria. These tests are an useful and economical way for obtaining reliable in situ properties of soils and provide the measurement of in situ stress-strain response of soils. From this test, the design foundations can be performed using pressuremeter rules that require a limit pressure, pl, and a pressuremeter modulus, EM. These two parameters are derived from the pressuremeter curve or deduced from existing correlations with undrained cohesion and internal angle friction (Ménard, 1957; Amar and Jézéquel, 1972), and are used to evaluate the bearing capacity of soil foundations and the expected settlements. But, they can also help to identify usual soil parameters required by simple constitutive models for soils in numerical calculations."

Jan 1, 2014

By Prakash Annamalai Rangasamy, Muthukkumaran Kasinathan

"Infrastructure development like elevated expressways, metro train and flyover are required proper foundation system to carry heavy traffic loads/significant lateral load, especially in the presence of hard stratum at shallow depth. Pile foundation under bridge pier system is widely adopted in metro projects where the piles are essentially socketed in rock. However, the drilling in hard rock is a time consuming process and needs heavy machineries which lead to delay in construction activities. In the present study, the influence of free standing height on rock socketing under lateral load is investigated. The experiments were conducted on an instrumented model pile with varying depth of socketing and for varying Lf/D ratios. The experimental results shows the load carrying capacity of the pile increases by increase in Lf/D ratio, where in the case pile without socketing (bearing on rock) is compared with 3D depth of socketing. Thus socketing the pile provides significant benefits on carrying capacity of lateral loads. Embedding the pile into hard strata reduces the lateral displacements substantially compared with pile bearing over hard strata. Form the study, it is noticed that the influence of rock socketing has significant effect in the lateral load capacity. And also, the effect of free sanding height play a major role in the lateral load capacity of the rock socketed piles.1. INTRODUCTIONA substructure carrying heavy lateral load at shallow depth, the structure has to be socketed into hard strata to enhance the efficiency of load carrying capacity. The existing field practice is to socket the end bearing piles in hard strata over a minimum depth of four times the diameter of the pile based on rock classification (IS 14593:1998). Reese (1997) developed p-y curves for analysing drilled shafts in rock under lateral loading, based on strong and weak rock criteria. The proposed p-y curve approach has the ability to simulate the nonlinearity and non-homogeneity of the rock mass surrounding the drilled shaft. Gabr et al. (2002) proposed a hyperbolic p-y criterion based on field tests on small diameter drilled socketed shafts. By considering pile as linearly elastic semi-infinite space and soil as homogeneous isotropic material, Poulos (1971) proposed solution to determine the horizontal displacement and pile head rotation. Poulos (1972) extended this elastic continuum approach to give an approximate solution by considering drilled shaft and pile bearing on rock as fixed and pinned end boundary condition. Zhang et al. (2000) developed a non-linear continuum approach for drilled shafts in a soil and rock mass by considering the effect of soil and/or rock mass yielding on the behaviour of shafts. Randolph (1981) conducted a parametric study on the response of laterally loaded piles embedded in an elastic soil continuum. The study was conducted using the finite element method and the results were fitted with closed-form expressions from which the lateral responses of piles were calculated. The solutions given by Randolph (1981) were expanded by Carter and Kulhawy (1992) from the results of finite element studies on the behaviour of laterally loaded flexible and rigid drilled shafts in rock. Desai and Christian (1977) gave a finite difference program to solve rock socketed problems by considering soil and rock mass as elastic-perfectly plastic. Zhang et al. (2000) verified the proposed finite difference method with existing field test results. Gabr et al. (2002) and Liang and Yang (2006) proposed hyperbolic p-y curves based on filed test results and verified with finite element programs. However the need of field and lab scale experimental studies to validate the existing methods of analysis is necessary."

Jan 1, 2015

By Wei Zheng

A pulverized coal fired power plant is being built in Osceola, Arkansas, along the Mississippi River. The subsurface soil conditions consist of a certain amount of very soft clayey silt and clay underlain with a medium dense sand layer and a dense sand layer. The site has been raised four to five feet with fill material consisting of sand and gravel. Consolidation settlement due to the fill is expected to cause negative shaft resistance (downdrag) on the pile foundations. The site is located in a high seismic hazard area - the New Madrid Seismic Zone (NMSZ). The liquefaction analyses indicated that there is a high liquefaction potential in the medium dense sand layer. Load tests are needed to determine the shaft resistance and the end bearing of each soil layer for design purpose. Two types of pile foundations ? augered pressure grouted displacement pile (APGD) and partial augered pressure grouted displacement pile (P-APGD) were considered for this project. Ten pile load tests, including five compression tests and five tension tests, were performed for three different areas. Strain gauges were installed for the compression tests. The APGD and P-APGD piles were installed side by side for comparison. In addition, three additional dynamic tests were performed to supplement the information from the static load tests. Load deflection curves for the compression tests were predicted, and the failure loads were interpreted using four different methods. The shaft resistance and the end bearing were determined from the strain gauge data and were used to back calculate the ultimate capacity. The back-calculated capacities are in good agreement with the predicted failure loads; they were further verified with the tension load test results.

Jan 1, 2007

By Juan J. Campo

The Freeport-McMoRan Main Pass Mine development in the Gulf of Mexico is a complex designed to extract up to 67 million long tons of sulphur over a 40 year period. The initial development includes 15 platforms and 13 bridges located in water depths ranging from 208 to 214 feet, approximately 15 miles east of the Mississippi River Delta. Three additional platforms were designed and installed for the oil and gas development in the complex. Over 110, 000 short tons of steel were required to fabricate the structures. As the sulphur is extracted significant subsidence is predicted over a major portion of complex in the shape of a very large bowl. Vertical elevations are predicted to change as much as 65 feet. Horizontal movements and mudline slope changes cause adjacent platform decks to move as much as 30 feet relative to each other. Differential soil movement is predicted between piling of individual platforms causing the piling to spread, resulting in significant lateral loading on the piling. Relative vertical soil movements are predicted along the lengths of the piles which causes "up drag" or "down drag" forces on individual piles. This paper addresses the design of the piling for the structures in the complex. Design criteria will be discussed explaining how the more traditional offshore environmental and gravity loadings were combined with the unique loading caused by subsidence. Design and analysis procedures will be explained and analysis results presented. These results include the incorporation of 100 ksi steel in thicknesses up to 5 inches in some of the tubular piles. Comparisons will be made between conventional offshore structures and these structures designed to accommodate the subsidence.

Jan 1, 1992

By Rajesh A. Vaidya

A large scale piling work is undertaken in India for an important fast track industrial project. Thousands of solid square precast concrete piles are driven to depths of around 50m. Soils encountered are of alluvial origin with very soft clays varying in thickness from 10 to 18m at the top followed by medium dense to dense and occasionally very dense sand, stiff clay and finally dense to very dense sand layer as the founding layer. Recent site grading with around 4 metres thick hydraulically filled river sand necessitated driving the piles to the bottom sand layer to avoid problems on account of negative skin friction and to achieve optimum pile capacity. A process approach suggested by Bell et al (2002) to promote better understanding of the pile behaviour, pile capacity, and parameters assumed at design stage for static capacity and for wave equation analysis is followed with an aim to bring in effective economy in terms of pile length and pile installation speed. Soil investigation work is also undertaken in stages to cut down pile wastage. A judicious combination of PDA and static pile load tests is followed. Pile Driving Analyser (PDA) tests at end of driving and also at various stages of recovery of pile capacity are carried out to understand the pore pressure dissipation phenomenon. The paper attempts to present some of the valuable experiences that would go to establish precast pile as a very effective alternative to driven cast-in-situ piles and bored piles which are very common in this part of the world despite their limitations in terms of economy, speed and certain geotechnical aspects.

Jan 1, 2007

By Hyung-Min Kwon

There are a number of methods available that can be used to estimate the bearing capacity of piles that are subject to lateral load, such as the theory of subgrade reaction or the elastic continuum approach. The objective of these approaches is to determine the lateral load corresponding to the allowable lateral displacement of the pile. It is important to select the appropriate soil stiffness when analyzing soil behavior within the allowable displacement of piles because the stiffness of soil is dependent on the displacement of piles. Even though pressuremeter tests can measure the stress-strain behavior within a wide strain range, pressuremeter test results have been utilized to assess only the fragmentary soil modulus based on either semi-empirical correlations or analytical approaches. This study is concerned with a methodology that can estimate the horizontal deformational property, while taking into consideration the nonlinear deformational characteristics of sandy soils. Pressuremeter tests were conducted for 15 cases using a calibration chamber. Reloading curves were employed in the estimation of horizontal deformational property in order to minimize the effect of soil disturbance caused by the installation of the probe. The shear modulus degradation characteristics were estimated from the curve fitting for the reloading curve and from extrapolation using the exponential function. In addition, the difference was taken into account between the stress state around the probe in reloading and that of the in-situ state. A consistent relationship was observed between the maximum shear modulus taken from the suggested method and the bender element tests performed in the calibration chamber, simultaneously with the pressuremeter tests. In addition, the results showed significant concurrence with the well-known empirical correlation.

Jan 1, 2008

By Mario A. Terceros H., K. Rainer Massarsch

"ABSTRACTThe Expander Body (EB) technology has been used successfully to increase the pile toe capacity of bored piles in loose to medium dense soil. An important advantage of the EB system is the ability to monitor the EB expansion process, which provides important information regarding soil strength and soil stiffness. This information, obtained for each installed pile, can be used to determine the actual shape and pile toe area. The expansion pressure can be used to design the pile base capacity.The Expander Body system has been recently improved by incorporating the possibility of post-grouting of the soil below the expanded pile toe. This improvement measure provides additional strength and stiffness to the pile toe and reduces pile settlement.The shaft bearing capacity of bored piles can be increased by using a soil displacement auger, which avoids soil decompression and increases lateral soil stress. This paper describes the principle of the EB system. During the past 20 years, a large number of EB piles have been installed in Bolivia and elsewhere, providing a sound database. Results from field loading tests are presented. A comprehensive study of test piles with and without EB base has been carried out which demonstrates the improvement effects that can be achieved by the EB pile system and the combination with the displacement auger pile method. A design concept for the EB pile system with the full displacement auger pile is presented. A high degree of quality control can be achieved by monitoring the entire pile installation process, including the displacement pile and the Expander Body.1. IntroductionIn many regions of South America, soil deposits consist often of predominantly loose to medium dense sands and silts, often with high groundwater table. In the Santa Cruz area in central Bolivia, such soils are frequently quaternary sediments, deposited by the river Piray. The city of Santa Cruz is located at the right bank of the river.The most common deep foundation method during the last 30 years has been cast in situ piles, augered and concreted under support of bentonite slurry. The design of such piles has been based on SPT results. However, SPT is often performed without quality control and the reliability of geotechnical data is therefore often poor. Traditional methods of pile installation with simple well drilling equipment of insufficient capacity are frequently used. Such methods lack basic requirements of quality control. Such piles have usually low toe resistance and work mainly by shaft resistance . Although the construction process and materials are cheap, the final product has variable and limited capacity. However, the most serious deficiency is that actually achieved pile capacity and pile settlement can be erratic and difficult to predict, leading to uncertainties with regard to actual foundation performance."

Jan 1, 2014