Search Documents

By C. Guney Olgun, Fleur Loveridge, Tracy Brettmann, William Powrie

"Abstract Deep foundations are increasingly being used, not just to carry structural loads, but also to act as heat exchangers as part of a ground source heat pump system. Such foundations, often called energy piles, have the potential to make significant contributions towards meeting the heating and cooling demands of buildings, thus reducing the overall energy consumption and carbon dioxide emissions during their lifespan. To ensure that the available energy from these systems is maximized, it is important to determine the thermal conductivity of the surrounding soils, a key design input parameter. In situ thermal response tests are commonly used to carry out this task for small diameter borehole heat exchangers. However, there has been debate over the applicability of these tests to energy piles due to their larger diameter and the consequent increased influence of the pile thermal properties on the test outcome. This paper examines the results of three thermal response tests carried out on piles of different diameters and thermal properties installed at the same site in Texas. Transient analysis of the test results, combined with comparisons to laboratory testing of soil samples from the site, is used to given an indication of the applicability of the thermal response test over different timescales for the different piles. It is concluded that the test is most suited to smaller diameter piles constructed with lower thermal diffusivity materials. Recommendations are given for the conduction of pile thermal response tests and interpretation of test data.INTRODUCTIONAs issues of energy security and scarcity become more important, the use of ground source heat pumps to provide renewable and sustainable heating and cooling to buildings is set to increase. Traditionally such systems use special purpose ground heat exchangers to extract and/or inject heat from/into the ground. The heat exchangers comprise a series of plastic pipes cast into the ground and then connected to the heat pump via a series of header pipes. In the case of building space heating, the heat pump then steps up the temperature difference to deliver the extracted heat at a useable level. However, financial and carbon savings can result by utilizing the building foundations as heat exchangers as well as to carry the building structural loads.Piles, often termed “energy piles”, are the most common type of foundation heat exchanger, and their construction has been increasing in recent years (Amis et al, 2009). However, while energy piles have the potential to make significant contributions towards meeting building heating and cooling demands, there remains scope for improving their thermal efficiency through improved analysis approaches (e.g. Loveridge & Powrie, 2013). In fact the greater diameter of many energy piles means they have the potential to deliver increased short term thermal energy storage compared to more commonly installed borehole heat exchangers."

Jan 1, 2014

By Mark R. Svinkin

Construction vibrations may be harmful to adjacent and remote structures, sensitive instruments and people. Construction vibration sources have a wide range of energy, displacement, velocity and acceleration transmitted on the ground. Effects of different dynamic sources and soil conditions on construction vibrations is analyzed. Consequences of construction vibrations are developed in various ways. It is important to assess intolerable vibrations before the beginning of construction activities. Guidelines for preconstruction survey are presented. Pre-construction survey and prediction of anticipated vibrations by IRFP method, monitoring and control of measured vibrations are important steps in preventing intolerable vibration effect.

Jan 1, 2000

By Feng Yongxuan

Anchored sheep pile is normally used in deep excavations, many of which only require stability in accordance with Terzaghi theory. In this paper, based on the experience, new lateral earth pressure method is adopted taking account into interaction among soil, anchors and sheet piles so that a group for the project under very difficult conditions and very severe requirments, especially, for the displacements are determined according to that mentioned above. During and after construction, displacements monitoring were carried out for about four months, which was proved that there was a little difference between calculation and practice.

Jan 1, 1991

By Dimitris Pachakis

In this paper, the authors give a brief overview of the current practice guidelines and tools for the seismic design of sheet pile quay walls, emphasizing how the design guidelines are lacking when the existing structure performance evaluation is required to meet performance-based criteria. Relying on recent experience they explain how the existing practices can be amended to focus more on performance evaluation as opposed to design. An example is given of an old sheet pile quay wall analyzed and evaluated for its performance according the recent performance criteria devised for Californian Marine Oil Terminals.

Jan 1, 2011

By A. J. Partos

One Liberty Place, at 315 m is the tallest building in Philadelphia, PA USA. It is supported on drilled piers socketed in heterogeneous rock. 3832 kN/m2 end bearing and 383 to 766 kN/m2 shaft resistances were selected. Design load distribution was 40% on the base and 60% by shaft resistance. The maximum compression on the corner core columns is supported by clusters of 3 drilled piers. In order to confirm load distributions along shaft and at the base, Drilled Pier G-10 supporting T13-A type outrigger column was instrumented. This column supports 53,849 kN compressive load which includes 13,440 kN windload. This paper reveals details about the process to select the final design for One Liberty Place together with pertinent Information about site geology, foundation construction, quality control, and methods of steel erection. It also presents detailed Information on the type of Instruments, their calibrations, field fabrication, and installation in the shaft of Pier G-10. Readings of concrete temperatures, computed loads, and load distributions are presented for a period from October 1985 through May 1988. The building was completed in 1987.

Jan 1, 1989

By Y. C. Han

The advances in seismic design considering soil-structure interaction or soil-pile-structure interaction are described using a substructure approach. The nonlinearity of soil is considered approximately using a boundary zone model with non-reflective interface, and computer programs are available for practical applications. The validation of model is confirmed with dynamic tests on piles in the field, and the results for a single pile are used to compare with the predictions in this study. The liquefaction for sand soil layer can be accounted for, and a case of liquefaction is discussed. Two practical examples are examined, a vacuum tower structure supported on foundation of steel pile group and a table top structure supported on foundation of concrete pile group. To illustrate the effects of soil-pile-structure interaction on the seismic response of vacuum structure, different base conditions are considered, rigid base, i.e. no deformation of the foundation; linear soil-pile system; and nonlinear soil-pile system. The method introduced can be applied to the design of tall buildings, bridges, industrial structures and offshore platforms with soil-pile-structure interaction under seismic or dynamic loads.

Jan 1, 2010

By Z. Q. Wang

The author is trying to clarify the existing problems in designing and laying out dynamic consolidation for soft ground improvement. Field testings and observations including vibrational parameters, pore pressures, stereoscopic photogrammetry etc. were run in order to trace the real behaviour of ground movement during tamping. It is believed that all the data got from the field work are rather informative and illustrative than that from theoretical modelling in the laboratory, thus some highlights relating effective thickness of compaction, maximum spacing between compaction points, number of blows for optimum tamping and seismic attenuation for environmental consideration are given.

Jan 1, 2010

By Issa S. Oweis

Two Towers are currently under construction in Central Moscow in the Russian Federation. Building A is a 96 story tower and Building B is a 65 story tower. The columns in both structures bear on a thick concrete mat that is supported on drilled shafts, 1.5 m in diameter. The shafts derive their capacity from weak limestone with layers of marl. Assigned allowable shaft loads were initially based on rock strengths that were later verified by load tests using the Osterberg Cell. One of the load tests was carried to near failure which allowed refining socket friction values that were later used in the design of Building A. All shafts were advanced using an auger and concrete placed in the dry. Grout tubes were placed with the reinforcing cage which allowed grouting of the limestone in contact with the shaft. Load sharing between the shafts and the mat was approximated using published methods as well as site specific finite element analysis. This paper covers the methodology of design, analysis of the Osterberg results to derive non-linear stiffness of the rock and differences between finite element analyses and results by approximate methods.

Jan 1, 2007

By Deep Foundation

Whenever an organization launches an initiative, the question arises whether that initiative has staying power. Or is the initiative, as is quite often the case, merely a fad; that is, just an activity that suddenly becomes popular, but which does not stay popular for very long. When the Federal Highway Adminis- tration (FWHA) started its Advanced Geotechnical Methods in Exploration (A-GAME) initiative, that question was addressed, especially considering the fact that up to 50% of major infrastruc- ture projects suffer impacts to schedule or cost due to geotechnical issues. Many of these issues relate to risks identified directly or indirectly to the scope and quality of site character- ization work. Effective site charac- terization is critical for recognizing. potential problems that may affect design and construction and for ensuring safe, well-performing and cost-effective projects. Grounded on that, knowledge of all available site investigation methods should continue to be shared widely and the application of those methods should be encouraged on an ongoing basis throughout the project lifecycle. The A-GAME initiative covers five technologies: Cone penetration testing (CPT), monitoring while drilling (MWD), electrical geophysical methods, seismic geophysical methods, and optical and acoustic televiewers. Of these, three soil and rock investigation methods were highlighted that are underutilized not only here in the U.S., but also in many places around the world: CPT: a well proven and established method for soil characterization that turned 90 last year, in which continuous in-situ data are col- lected quickly and consistently. Geophysics: the science that assesses the physical properties of the soils and rock using seismic and electrical techniques, which con- tinues to advance in leaps and bounds as the application of well- understood technologies become more powerful.

May 1, 2023

By Aly M. Mohammad

Croton Point Avenue Bridge carries Croton Avenue over Metro-North main tracks at Harmon Rail Yard in Westchester County, New York. The new bridge is 1100 foot long and 36 foot wide nine span structure with three spans continuous units. The spans are steel multi-stringers, composite with concrete deck. The piers are solid wall piers and the foundations are spread footings. During the design of the bridge foundations it was determined that the relatively loose to medium dense sand layer is susceptible to liquefaction under a design earthquake with a seismic coefficient of 0.15g. Several foundation options were considered for the new bridge including both shallow and deep foundations. It was determined that the most cost effective alternative is to use spread footing foundations supported on densified soils. Vibratory probes were utilized to densify the loose to medium dense sand layer and reduce the risk of liquefaction. Densification test sections were performed to determine the optimum spacing for the vibro probes. The test sections included performing piezocone tests before and after the densification to compare the increase in relative density of the sand. In addition, ground surface settlement due to the vibro probes was measured and correlated to the increase of soil relative density. The paper will present the results of the ground improvement method utilized and correlate the spacing of the vibro probes and the increase in relative density and the results of the piezocone tests performed before and after the densification. It was found that the vibro probes are not as effective as thought at shallow depth below the ground surface. It is believed that the results and finding presented in this paper will benefit both the design and construction industries by providing a relatively cost effective means to improve the soils

Jan 1, 2007

By Mitsuhiro Shibazki

I can't answer that question but I am looking at Andy, my co-author, and he says we didn't measure it. No movement. If I understand it correctly, how do we handle lateral forces in shear? The main columns were designed as pin connections so there wasn't a moment in the shear between the pile cap and the columns the steel reinforcing was used to resist that. I am not aware of how we would have installed those, it is possible to try and submerge them all if the jet grout is still fluid. They were higher than design. You are correct.

Feb 10, 2003

By Peng Jiahong

With ultrasonics application during checking the large diameter cast-in-situ pile body, it is usualy applied the statistical method of probability and PSD. This paper presents a converse probabilistic-analytical method which can identify important anomalies, both strong and weak, during interfered situation. So the inhomogeneity in concrete pile may be ellectively distinguished. In order to ensure the capacity of bed rock support layer under large diameter pile, a test-in-situ is conducted to determine the compresive strength and shear force inserting rock of the support layer, so the compresive strength and modulus value of elasticity of bed rock tested will closely tally with the actual situation.

Jan 1, 1991

By K. C. Foye

Use of load and resistance factor design (LRFD) of foundations is growing, from offshore applications to bridge applications and beyond. The development of load and resistance factors for design has traditionally relied on calibration to traditional factors of safety. This technique, however, offers little insight into the challenges of pile design. This paper discusses an approach to LRFD factor development that seeks to isolate the various sources of design uncertainty. Using this approach, reliability analysis is used to develop resistance factors for the design of driven pipe piles in sand. These findings shed light on many aspects of the ongoing discussion of how LRFD can be successfully applied to pile design.

Jan 1, 2008

By Balu E. George, Subhadeep Banerjee, Shailesh R. Gandhi

"A three-dimensional analysis of laterally loaded helical piles installed in cohesionless soil is presented. Finite Element Analysis was conducted using commercially available Plaxis 3D AE version, assuming Mohr-Coulomb failure for soil. Pile is modelled as plate elements with a single helical blade attached to a hollow shaft. The ultimate load for various configurations is examined considering deformation criteria. The Bending Moment distribution and maximum lateral deflection are also discussed. It was observed that the ultimate lateral load carrying capacity increased by presence of helical blade and the maximum deflection also got reduced. The diameter of the helical blade was found to have significant effect on the lateral deflection, maximum bending moment and the ultimate load. However, the observations from the study suggest that the presence of helical blade seizes to produce considerable effect after a certain depth. Difference in failure pattern with regard to the distribution of soil resistance observed for different geometries considered for numerical analysis are also touched upon.INTRODUCTIONHelical piles or screw anchor piles have gained popularity due to fast installation, instant use, and other advantages over the traditional piles. They are usually used to support structures like solar panels, light houses, and other light structures which are subjected to uplift loads. However, such structures are often subjected to significant lateral loads as well. Under lateral loads, the response of helical piles can be different from that of a conventional pile due to the presence of the bearing provided by the helical blade. However, the proper design remains a concern due to lack of work carried out on the lateral capacity of helical piles.The lateral performance of helical piles is significant because they can act as efficient alternative to conventional piling systems in many applications.The lateral load capacity of screw anchor piles with different number of helices were examined by Mittal et al. (2010) by experiments in sand. They found that the lateral load capacity of piles increases with addition of helical blades. Prasad and Rao (1996) examined the lateral capacity of helical piles in clay by experiments on model piles and found that the lateral capacity of helical piles were more than that of the straight shaft piles. It was observed that the lateral capacity increase with embedment depth and shear strength of soil. Sakr (2009) studied lateral performance of two section helical piles in soft soil. The investigation by Prasad and Chari (1999) reported that the pressure distribution across the diameter is not uniform for circular piles, but it is maximum at the centre and almost zero at the two edges.Puri et al. (1984) after conducting model tests on single-helix, two-helix, and three-helix anchors installed in sand, proposed a mathematical model that was fashioned after Matlock and Reese’s elastic theory model. Elkasabgy and Naggar (2015) investigated he lateral performance of full scale large capacity helical piles in structured cohesive soils and reported the modulus of sub-grade reaction to be non linear."

Jan 1, 2017

By Mary Ellen Bruce Large, Antonio Marinucci, Silas C. Nichols

Tip post-grouting of bored pile (drilled shaft) foundations refers to a method where cementitious grout is injected beneath the tip of a shaft to improve the overall performance of the constructed foundation. This technique, when performed satisfactorily and in the appropriate ground conditions, enhances axial load-displacement performance by improving the mobilization of pile’s resistance. Potential benefits associated with tip post-grouting include reduced settlement under loading, better alignment of load transfer curves, and improved ground beneath the base of the bored pile. However, to be able to realize the benefits attributed to this method, the design, construction, of both the bored pile and the post-grouting system must meet a minimum level for quality assurance. The various factors affecting the successful installation and performance of a bored pile (e.g., workmanship, base cleanliness, borehole integrity, and concrete placement) have been discussed by numerous practitioners and researchers in the available technical literature. For a conventional (i.e., ungrouted) bored pile, acceptance is based on a combination of visual inspection, material testing, and the results of integrity and/or performance testing of the constructed pile. A properly executed tip post-grouting program can be a relatively comprehensive and complex process, which is typically evaluated throughout the construction process based on the results of prior projects and/or on test pile(s) at the particular site. For tip post- grouting programs, verification procedures and acceptance criteria should be established during and incorporated into the design process to ensure design intent and objectives are achieved. Project specifications should be produced to ensure performance requirements are achieved. This paper will present and discuss factors affecting the successful execution of tip post-grouting, including grouting criteria, instrumentation, reliability and uncertainty with the method and outcome, and verification and acceptance. INTRODUCTION Constructing bored piles (drilled shafts) is increasingly more challenging given the lack of ideal site locations, tight project site confines, difficult or restricted access, greater demands on drilling equipment, and close proximity to adjacent structures. To evaluate the feasibility of bored piles as an appropriate foundation system, a myriad of factors is evaluated during design, including site conditions and constraints, budgeting and scheduling, reliability and risk exposure, presence of and depth to adequate load bearing soils/rock, and the magnitude of the imposed loading. Moreover, updated design codes increased load demand per element, and improved material strengths have led to more complex foundation designs, larger foundation elements, and significant increases in load magnitude. Monopile (monoshaft) foundations have been utilized where one large bored pile is used in lieu of a group of piles connected via a pile cap. In addition, to accommodate the design criteria, site conditions, and imposed loading, the geometry of the bored piles being designed and installed have been as large as 13 feet (4 m) or greater in diameter and to depths in excess of 260 feet (80 m).

Jan 1, 2018

By J. Matos e Silva

"Abstract Although one can think that it is very low the probability of a seism occurrence during the execution of an excavation in an urban lot protected by a diaphragm wall curtain, reality shows that whenever a seism occurs in an urban area several diaphragm walls will be affected by it. So it is advisable to consider the seismic action when designing a diaphragm wall curtain. The paper refers the main information about the seismic design of diaphragm walls according to the Eurocodes 7 and 8 and to the Portuguese Norms related to them (respectively NP EN 1997-1 2010 and NP EN 1998-5 2010), as the Eurocodes consider the possibility of each European country to adopt their own seismic parameters as the seismic risk is different in each country. Thus the so-called National Document of Application (in our case the Portuguese Norms) prescribes the seismic local parameters.1 - EUROCODES AND PORTUGUESE NORMS PRESCRIPTIONSAccording to Eurocode 8 - Part 5 and to the related Portuguese Norm NP EN 1998-5 2010, seismic actions on soils should be quantified adopting the Mononobe-Okabe method that gives goodapproaches when compared with reality.From paragraph 7.3.2.2 of the referred Norm, the horizontal seismic coefficient kh will be:"

Jan 1, 2014

By Nien-Yin Chang

The contemporary seismic response analysis of structures using a finite element analysis code requires six elastic spring constants to address the six degrees of freedom ground/foundation contribution to the response of a structure to earthquake shaking. However, the ground response is nothing but linear. Thus, it is critical to address the effect of the nonlinear ground response to the performance of structures under strong earthquakes. This study specifically addresses the effect of pile foundation on building vibration using finite element analyses. The effect of single pile was first investigated and the load was applied at the pile head using the single-degree-of-freedom load at a time, including three translational loads in the x, y and z directions and three moment loads about the three respective axes. In this study, the coupling effects between two or more different loads were not investigated. A load is increased monotonically to investigate the nonlinear behavior of pile under various loads. The Mohr-Coulomb model was used to represent concrete. To explore the effect of soil models on the nonlinear spring functions, the following constitutive models of soils were used: linear elastic, Mohr-Coulomb model, Cap model, modified Cam-Clay model, and Duncan-Chang hyperbolic model.

Jan 1, 2007

By Richard Deakin

This case study describes aspects of the design of bridge foundations using 320mm diameter steel tube piles in the vicinity of Montréal, Canada. In this area, these piles are a very commonly used and cost effective solution for deep foundations. Typically they are driven through thick Champlain Sea Clay to bear onto stiff, strong rock. However, in some locations there is a layer of glacial till between the base of the clay and the rock which cannot always be fully penetrated by the piles. There is currently little published information, about the bearing capacity of these piles in the local till, and this paper presents and discusses some pile-test data from a recent project. The nature of the glacial deposits in the study area is presented using information gained from published geological data, the project ground investigations and site observations. The design approach and assumptions are discussed, together with the aims and outcomes of preliminary field driving trials and pile tests. The paper then discusses the results of dynamic tests undertaken on production piles. Bearing capacity factors are back analysed from the dynamic test results and compared against values assumed within the design. Observations are made that designers of future foundations in similar conditions may find informative.

Jan 1, 2011

By William Auyeung

Micro-piles are small-diameter, drilled and grouted reinforced piles used for both structural support and in situ earth reinforcement. They were conceived in Italy in 1952, but have become popular in Canada and the United State only since the mid-1980s. The Province of British Columbia completed a construction of a 265-km (165 miles) four-lane highway between Campbell River and Victoria in the year of 2000. The construction of Big Qualicum Bridge was part of the above mentioned provincial government project and this bridge was made of twin cast-in-place concrete parabolic arch structures. The overall length of the bridge is 261 metres (856 feet) and the width is 24.2 metres (80 feet). The massive thrust from each arch is resisted by groups of 46 drilled micro-piles that are about 230 mm (9 inches) in diameter with No. 18 high strength Dywidag threaded bars with double corrosion protection up to 15 metres (50 feet) long. This paper will describe the micro-pile design and installation methods. The performance of the micro-piles in full scale testing in tension and compression monitored with electronic strain gauges will be presented. The impact of drilling methods on the performance of the micro-piles will also be discussed.

Jan 1, 2004

By Djk Arentsen

A new technique to drive tubular piles by impact hammer inside the pile has confirmed a dramatic reduction of noise and the opportunity to save steel. Also a reduction in driving time and a higher bearing capacity has been observed during a test program of this technique. As part of the so-called "Down-the-hole" driving technique, a wave equation analysis has been developed to calculate driveability and pile stress. The main feature of the new "Down-the-hole" technique is the development of a patented device allowing uncoupled penetration of pile tip and pile shaft, which makes it possible to drive both closed or open end piles and reduce the stress level induced in the pile wall. During a test program, a number of instrumented piles were driven and compared with traditional driving of the same pile with the same hammer on top (also instrumented). Also the stresses and performances were compared with precalculations. This paper, explains the technique and presents the test and noise results, in comparison with traditional top-pile-driving. The "Down-the-hole" driving technique is an interesting alternative for special applications where traditional pile driving requires a large wall thickness or in areas where noise is a hot item.

Jan 1, 1996