Search Documents

By Patrick P. A. Wolfs

In the summer of 2000, the ECR®/EFT® was first introduced in the Netherlands. After the first project a field test was performed together with other geophysical methods to prove the liability of these systems and their application in areas with soft soil and high groundwater levels. The objective of this test, which was carried out with three leakage detection systems, was to locate the holes. After this test several projects have been carried out. In this article the Dutch projects "Ringvaart Aqueduct" and "Bottleneck Limburg N296/N297" are mentioned.

Jan 1, 2006

Jan 1, 2000

By A. E. Fiorato

A test program was conducted to evaluate use of high-strength concrete in drilled shafts (caissons). The objective of the program was to determine if internal temperatures developed during cement hydration, or other characteristics of high-strength mixes, affect in-situ strength and stiffness. This paper covers strength results. Two 10-ft (3.0-m) diameter by 40-ft (12.2-m) deep caissons were constructed using two different commercially available high-strength concretes, a "low-heat" and a "high-strength" mix. Measured 6x12-in. (150x300mm) moist cured cylinder strengths at 56 days were 13,690 psi (94 MPa) for the "low-heat" mix and 17,130 psi (118 MPa) for the "high-strength" mix. Compressive strengths and moduli of elasticity of cores taken from the caissons were compared to those of companion cylinders made during casting of the caissons and stored in a moist room. Strengths of 4x8-in. (100x200 mm) cores taken at four ages and tested between 34 and 398 days averaged 81% of strengths of 6x12-in. (150x300 mm) moist cured cylinders at corresponding ages. In-situ (core) strengths of the caissons did not appear to be measurably affected by temperature. However, the data indicate that core strengths were sensitive to level of consolidation, as reflected in entrapped air voids. Overall, the results indicate that high-strength concretes can be used in drilled shaft (caisson) foundations.

Jan 1, 1991

By David Siu

Many problems were encountered with the mechanical wedge-type splices used for the 15-inch square precast prestressed concrete piles installed at an industrial plant site. Many of the wedges were breaking during installation of the splices and after pile driving resumed following splicing. Dynamic monitoring of the piles and uplift loading tests confirmed that the problems were associated with cracked or damaged wedges. More ductile, annealed wedges were subsequently used, and, while not completely satisfactory, they were found to perform better than the original more brittle wedges. Introduction Long precast prestressed concrete piles were installed to support heavy, settlement-sensitive structures at an industrial plant in Port Alberni, British Columbia, Canada. The piles were driven through soft compressible silts and clays to toe bearing in a dense sand and gravel deposit or on bedrock. Each pile consisted of two or three segments joined with mechanical wedge-type splices trademarked DYN-A-SPLICE. Shortly after construction began, problems arose during pile installation, and these problems were, later, identified to be related to the wedges, or clamps, used to connect the splice plates.

Jan 1, 1991

By W. D. Guo

With an experimental apparatus developed recently, model tests on piles were conducted in sand subjected to triangular soil movement profiles. Four instrumented piles tests are reported, which show the pile behavior predominantly determined by soil sliding depth. Axial load can create additional bending moment and pile deflection, which also make mode of pile-soil interaction change with sliding depth. Limiting resistance was found 1.5~3 times higher than currently used for laterally loaded piles in sand.

Jan 1, 2006

By Brian M. Fraley

"Portions of the Catholic Total Abstinence Fountain in Fairmount Park in Philadelphia, Pa., were in “imminent danger,” according to a restoration services request for proposals (RFP) issued by the City of Philadelphia in August 2014. Open voids in the subsurface beneath the foundation were causing ongoing settlement of the fountain.The fountain was unveiled in 1876 as an ornamental drinking fountain for the Centennial International Exhibition, which celebrated the signing of the Declaration of Independence. Its creation was commissioned by the Catholic Total Abstinence Union of America, an Irish temperance organization that advocated for total abstinence from alcohol. Ironically, the fountain ran dry decades ago.The now-defunct fountain features a 100 ft (30.5 m) wide granite base with three steps in the shape of a Maltese cross. The centerpiece — enclosed by a 40 ft (12.2 m) diameter basin — is a 15 ft (4.6 m) tall statue of Moses perched atop an iglooshaped marble mound. Four subsidiary statues rise from granite pedestals at the tips of each arm of the cross, including Archbishop John Carroll, Charles Carroll of Carrollton, Father Theobald Mathew and Commodore John Barry.Natural and Man-Made DamageThe City of Philadelphia’s RFP called attention to three “high priority structural areas.” It was noted that Moses, Father Mathew and the steps surrounding the fountain had been documented as public hazards. The long-term effects of water infiltration had set in, eroding mortar joints and causing some stones to jut out. Furthermore, the stone base supporting the 16 ton (14.5 tonne) statue of Moses was in danger of collapsing. The statue of Father Mathew had been struck by lightning in 1910 and was repaired with an iron and metal pin anchor system, which had succumbed to corrosion. The city considered the statue of Father Mathew as the most threatened of the statues. Mike Miluski, P.E., vice president of Compaction Grouting Services (CGS), recalled “the fountain was in pretty bad shape” as he walked onto the site in August 2016 and immediately recognized the challenges ahead."

Jan 1, 2017

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2003

By Takefumi Takuma, Hiroyuki Nishimura, Shigeru Kambe

"In order to achieve tubular pile driving with low noise and low vibration, the Press-in Piling Method has been adopted on many projects. The method utilizes reaction force derived primarily from previously driven piles to push in the next pile into ground. With attachments, the Press-in piling equipment can deal with hard soil as well as difficult site conditions. At West Toronto Diamond Rail Grade Separation Project in Toronto, Canada, the Press-in piling equipment drove more than 500 of 914 mm (36 inches) diameter tube piles in length of 12 to 25 meters (39 to 82 feet) to construct earth-retaining walls for railway grade separation. Myoshoji River Restoration Project in Tokyo, Japan drove some 600 of 1,000mm (39.4 inches) diameter tube pipe sections in length of 11 to 22 meters (36 to 72 feet) by the rotary Press-in piling equipment to increase the flood drainage capacity of an existing river in highly populated area of the city. Both projects exemplify the advantages of the method in urban settings.1. BACKGROUNDThe Press-in Piling Method was invented some forty years ago in Japan, where a very large number of construction projects were causing widespread construction pollution, especially by pile driving work in densely populated areas. The method has been providing solutions for piling projects which could not have been built otherwise due to the noise and vibration impact to the surrounding communities. The method can be used with various types of piles including sheet piles, tubular piles, concrete sheet piles and so on. With high pressure water jet and continuous flight auger attachments, the Press-in piling equipment can deal with dense sand, stiff clay, gravels, boulders and even soft rock without employing a different set of equipment."

Jan 1, 2015

By Timothy D. Stark

Jet grouting has increasingly become a ground improvement technology used to address seepage concerns and provide strength improvement to soils underlying dams. The technique of jet grouting uses high pressure/volume jet fluids to erode existing soil, evacuate some or most of the soil, and mix the remaining cuttings with cement slurry to form soilcrete. While considered a useful technology, this paper discusses some of the problems that can develop while jet grouting in or below a dam with an operational reservoir and seepage condition. Jet grouting experience at Tuttle Creek Dam indicates concerns with respect to ground fracture; spoil return, column diameter consistency, and homogeneity of resulting soilcrete. Recommendations are presented to increase monitoring of downhole parameters during jet grouting to better understand the downhole pressures and soil response during jet grouting.

Jan 1, 2012

Precast prestressed concrete piles designed to be end-bearing in a sand stratum at Drax Power Station met with extremely variable resistance during driving. Some piles came to virtual refusal almost immediately on entering the sand whereas others were driven to considerable penetration with very low resistance. Redriving and load tests on piles experiencing low resistance on initial drive showed that take up in strength occurred over a relatively short period of time. Investigations involving the use of pneumatic piezometers revealed the development of significant excess pore pressures during driving. Samples from boreholes showed that piles met the least resistance when the sand had a high silt content. Comparison with the original site investigation data demonstrated the difficulties in predicting detailed pile behaviour. The varied behaviour could not be related to the original borehole logs or to SPT or static cone penetrometer results. The factors controlling pile driving behaviour were essentially geological and could only be explained with reference to local soil grading.

Jan 1, 1989

By B. M. Das

Several laboratory model test results for the determination of the ultimate uplift capacity of single and group metal piles embedded in near-saturated clay have been presented. Based on the uplift test results for single piles, the variation of the adhesion factor with the undrained shear strength of clay has been determined, and an empirical correlation for estimation of the adhesion factor in soft and medium clays has been presented. The group efficiency of piles under uplifting load depends on factors such as embedment ratio, undrained shear strength of clay, the number of piles in a group, and the center-to-center spacing of the piles.

Jan 1, 2010

By Eiji Kojima

In this research, dynamic and static load tests were performed on permanent foundation piles which had a pile length of 30 m, 800 mm in outer diameter and 15 mm in wall thickness. In this site the dynamic horizontal load test on a smaller test pile, 12 m in length, 500 mm in outer diameter and 12 mm in wall thickness, was also carried out. The static horizontal load versus horizontal displacement derived from the dynamic load test conformed well to that measured in the conventional static horizontal load test of the pile with 800 mm diameter. Then an attempt was made to predict the horizontal load displacement of the pile with 800 mm diameter based on the results of the dynamic horizontal load test of the pile with smaller diameter of 500 mm.

Jan 1, 2006

By Alan B. Wagner

Data from seven instrumented pile load tests in Milwaukee, Wisconsin and two other instrumented load tests reported in the literature, one in Evanston, Illinois and one in Houston, Texas were reviewed. The data were for pipe piles having diameters from 9-5/8 inches to 18 inches, driven to depths between 36 and 96 feet. These data were used to develop a relationship between effective vertical stress and unit side friction and unit end bearing. These relationships were based on readily measured soil parameters, undrained shear strength, Cu, and Standard Penetration Test (SPT) values. This Beta (ß) and Nt approach and four other methods were then used to calculate the bearing capacity of the nine cases analyzed. The results from each of the methods are compared with the measured results.

Jan 1, 1991

By D. V. Karandikar

Contiguous bored piles have been used in the past for retaining the sides of deep excavation. An innovative version of this method was adopted successfully in two prestigeous projects in Bombay in which in a very constricted and congested locality, adjoining seashore at Walkeshwar, 14 m deep excavations with vertical sides were required. 600 mm dia bored cast-in-situ piles were first installed at 1.2 m c/c and subsequently as the excavation proceeded, they were tied to cast-in-situ RCC waling beams. The shear connectors to the beams were pre-fixed to the pile reinforcing cage at specified depths. The pile / waling beam system was anchored into the ground by installing inclined prestressed cable anchors at the designed depths. The waling beams were also used to support the brickwalls, which formed the required backup wall for fixing the tiled water proofing system. Catch-drains were installed behind the brickwalls for relieving the ground water pressure and thus ensuring a very economic design. The adequacy of the system was proven in that where the system was not installed in time, failure of the sides occurred during monsoon. Whereas in the areas where the above retaining system was installed, there were no problems inspite of heavy monsoon and surcharge of construction materials and equipment. The system became a very effective and economic alternative to an anchored diaphragm wall. The paper presents the case studies of these two projects.

Jan 1, 1996

By Y. G. Li

The design and construction of the hand-dug caisson pier foundation of the Shenzhen International Trade Centre are described in the paper. In addition discussions and inquires about the load-bearing capacity of the hard bedrock are offered.

Jan 1, 2010

By Frederick C. Rhyner

Drilled shafts have become an economical foundation choice for bridges in the northeast United States, especially when they can be constructed over water without the use of cofferdams. For the Boscawen-Canterbury Bridge over the Merrimack River in New Hampshire, an unusual design was used to avoid the use of cofferdams and avoid the need for pier caps at the waterline. This design used a pair of integral drilled shaft ? columns to form a bent type of substructure for support. Drilled shafts were 8-foot diameter, about 90 feet deep, with 16-foot long rock sockets. These are integrally constructed with 6-foot diameter reinforced concrete columns extending 37 feet from the waterline to the superstructure. Design load cases focused on lateral loads from ice flows, stream flows, wind and seismic events. Alternative analyses using different methods were made to check the design results. This paper discusses the subsurface conditions, design of the drilled shafts and columns, rebar and joint detailing issues, and construction of the drilled shafts.

Jan 1, 2004

By Randy R. Huberty

Although originally designed with deep foundations consisting of all driven steel H piles and drilled caissons, a unique application of Augered Cast-in-Place (ACIP) piles as an alternate design resulted in a significant cost savings for the Midfield Terminal Project at the Pittsburgh International Airport. The project was enormous in scope covering an area two miles long by one mile wide, with changes in elevation of over 200 ft. The varying geology combined with the large amounts of fill required resulted in a complex set of geotechnical design parameters that had to be evaluated through both load testing and analyses. A total of almost 400,000 lineal feet of ACIP piles were installed for this project.

Jan 1, 2001

By Mark X. Haley

Foundation design and construction in Boston has changed dramatically during the past 10 years. Prior to 1985, the primary foundation element in Boston, where deep foundations are required, was driven end-bearing piles. Since 1985, drilled or excavated high capacity foundation elements have been utilized more frequently. This paper will provide a historic perspective of their use and a summary of design parameters for elements installed and founded in the bedrock. TOPOGRAPHY Boston was founded in 1630 by the Massachusetts Bay Company of John Winthrop and his hearty band of Puritans. The settlement was chosen for: ? its safe harbor, ? abundant source of fresh water, and ? peninsula setting offering protection of the ocean on almost all sides with high ground for fortification. These three factors were a direct result of past geologic processes that created the Boston Basin by erosion of the soft bedrock underlying this area as compared to the harder granite rock to the north, west and south. As the glacial ice sheets melted and moved northward, various soil types were deposited. During ice sheet re-advancement the hills and islands of Boston took on their precolonial shapes. The Trimont, consisting of Beacon, Mt. Vernon and Pemberton Hill, rose to 150 ft above sea level with the smaller Copps and Fort Hill to the north and south.

Jan 1, 1994

By David C. Kraft

A major manufacturer and user of machine tools had the need to install a screw press machine at its plant site with the following design load requirements: (1) Vertical Compression Live Load = 2000 kip (8896 kN) and Dead Load = 1000 kip (4448 kN), (2) Rotational Moment = 6600 ft-kip (8950 kN'm). The screw press machine was to be located within an existing manufacturing building. The bottom of the footing base was located 15 ft (4.6 m) below existing floor slab. A geotechnical investigation of the site indicated a 17 ft (5.2 m) thick initial stratum of stiff to very stiff clay underlain by a 14 ft (4.3 m) thick stratum of loose to medium dense sand. Beneath the sand stratum was soft rock described as weathered shale. Obvious concern was raised on the possible effects of the dynamic motion of the screw press and potential resulting settlement within the loose sand stratum. This combination of large loads and dynamic motion resulted in the selection of a helical pile and tieback system to support the concrete foundation. The helical pile foundation system consisted of a group of vertical helical piles installed into the shale rock and a group of inclined helical tiebacks set into the remaining portion of the clay stratum. Four load tests were conducted on the vertical helical piles in order to establish compression load capacity. The results of these load tests as reported herein, led to the addition of a limited number of tubular steel push piles in order to meet the project required Factor of Safety on the design loads. All of the helical piles, push piles and inclined helical tiebacks were successfully installed and the screw press is now installed and operational.

Jan 1, 2003

By B. Sivarama Sarma, Biswabikash Rout

"Seepage control has to be achieved with plastic concrete cut-off diaphragm walls in dam structures. Materials selected for construction of cut-off walls must be durable, impermeable and have stiffness comparable to the surrounding soil.Plastic concrete provides a feasible and economical solution for construction of durable and impermeable cut off walls for dam structures. Plastic concrete wall should not be understood as a concrete wall with similar mechanical properties of concrete used in buildings, piles and spillways sections. Though it consists of the same materials as those of conventional concrete it has the major differences in end product due to predominant addition of bentonite slurry in the mix with very high water cement ratio. This makes the hardened concrete with very low compressive strength less than 5MPa and high failure deformations after the peak load.This technical paper examines a case study, the typical specifications on demand for construction and the issues corresponding to misunderstanding of the material as a structural grade concrete material. Conclusions were drawn based on a few project site quality data and trial mix experimental data. The anomalies in specifications on demand for construction of curtain wall in a dam structure were removed with modifications.INTRODUCTIONDiaphragm walls which are constructed in trenches made of plastic concrete basically serve the function of seepage control under confined measures. They should have the ability to sustain and undergo large plastic strains as compared to conventional concrete. The three basic mechanical properties of plastic concrete cut-off walls are to have least permeability, minimum strength to retain its shape and ability to undergo large deformations under confined loading conditions. The constituents of plastic concrete are cement, bentonite, coarse and fine aggregates, chemical additives to improve flow of concrete and sometimes to retard the setting time and water."

Jan 1, 2017