Search Documents

By Paul Suver

The closed loop standing column well (CLSCW) system uses a closed circuit of water to develop the same thermal heat exchange characteristics that are achieved from traditional open circuit standing column well that uses the ground water directly. Pipe pile and pipe anchor foundations can be used as CLSCW components for ground source heat exchange. New data gathering and analysis techniques and equipment installed in the heat pumps allow any mechanical engineer to design the system without specialty engineering equipment and certifications.

By F. Castelli

A simplified non-linear method to predict the behaviour of a single pile and/or pile group under horizontal loads is presented in the paper. The evaluation of the non-linear lateral deflection is based on a procedure taking into account the decrease of the model stiffness with the increasing of the applied load. The solution derived firstly for the single pile, was extended to the case of a pile group introducing the p-multiplier (fm) concept proposed by Brown et al. (1988).

Jan 1, 2006

By Rajesh Minda

160 numbers of double bulb underreamed piles were constructed based on the safe loads specified in IS code at Tripura. The pile load tests yielded a much lower capacity. A detailed investigation work was carried out to find out the reasons for anomaly. The work included soil exploration followed by extraction of two piles bearing numbers 72 and 151. It was seen that the bulbs were not formed as per specification. Some comments on IS Code have been made at the end.

Jan 1, 1996

By A. Tejchman

On the site of building of a new flyover founded on piles the comprehensive "in situ" investigations were carried out. The subsoil conditions under each of 15 supports were very differentiated. Using of the static sounding results a new method for evaluation of bearing capacity and settlement of piles was proposed. The method is based on a special construction of the curve of load-settlement relationship. The verification of this method was made on the basis of loading of piles.

Jan 1, 2010

By P. M. Deshpande

An interactive short column system is evolved as alternative to deep foundation system in deep layers of marine clay, the interaction of encased stone column and marine clay carry load without causing conventional settlement. This paper presents concept of the system and its field application as foundation of culverts on marine clay layer of 15 to 17 M underlain by residual soil layer of 5 to 6 M, where conventional pile of 23 to 25 M would have been required.

Jan 1, 1996

By T. Matsui

Many existing bridge abutments on the soft ground laterally move and their many damage examples have been reported. An essential cause for the troubles of the lateral movements may be the lack of examinations for the lateral earth pressure acting on its foundation piles. In the present paper, actual movement condition of existing bridge abutments is first summarized, and then the author establishes a practical and systematical design method for bridge abutment foundation piles, including the examination for the passive pile.

Jan 1, 2010

By Jim Cook

Arsenal Football Club required the development of a new home stadium in north London, subsequently named the Emirates Stadium. The proposed development comprised a 60,000 seat stadium, with associated facilities and a sports training centre. Described are the foundation solutions and piling construction techniques used, which take into consideration the potential impacts on existing above and below ground railway infrastructure and underground water structures. Methods used by the piling contractor to improve aspects associated with health, safety and quality are also described.

Jan 1, 2008

By Lok M. Sharma, Deep K. Khatri, Bradfield. Brett

"A shored enclosure was required to access a control structure upstream below the dam of a deep lake. The shoring involves the interaction of the structure, soil, and water and the loads imposed include the hydrostatic forces of the water, soil pressures as well as dynamic forces due to currents and waves. Deep excavation support systems have traditionally been designed using classical methods that involve direct computations of earth pressures. However, traditional analysis does not take into account soil-structure interaction. Numerical modelling offers better means to analyze soil-structure interaction. This paper presents a 2D finite element (2D-FE) analysis of a deep excavation support structure that was required to remove and replace a control structure at the upstream toe of a dam. The sheet-piling shoring was designed to withstand the lateral pressures from 14 m deep free water and 5.5 m deep excavation below the free water to reach the required excavation level to replace the gate structure. Elastic-plastic analyses were performed to predict the stresses and deformations of the complicated shoring structure and excavation bottom. The soil parameters, procedures used to develop the 2D-FE model, and the results are discussed in this paper. The shoring system is currently under construction.INTRODUCTIONA deep shoring system enclosure is required to keep out water and soil and to provide a support for unbalanced loadings due to dewatering and/or, excavation in order to permit construction of the permanent structures in the dry. A braced shoring system consists of a single wall sheet piling which is driven into the ground to form a “box” around the excavation site and is braced on the inside. After bracing the sheet piling, seal concrete is placed into the bottom to prevent water from seeping into the open excavation from underneath the sheet piling, and the water is pumped out to provide the dry work area. The braced shoring involves the interaction of the structure, soil, and water and the loads imposed include the hydrostatic forces of the water, soil pressures as well as dynamic forces due to currents and waves. Deep excavation support systems have traditionally been designed using classical methods that involve direct computations of earth pressures, (active, passive, or apparent pressures). There have been some uncertainties regarding the actual distribution of earth pressures due to influence of the support wall flexibility, as these traditional methods do not take into account soil-structure interaction. Numerical modelling offers better means to analyze soilstructure interaction."

Jan 1, 2017

By Dawn C. Tattle

[ ] Panoramic View of Completed Facade Supports The following case history describes the installation of earth retention systems, historical facade supports and structural caissons by Anchor Shoring & Caissons Ltd. at the Air Canada Centre/Raptors Stadium Project in Toronto, Ontario, Canada. The Air Canada Centre/Raptors Stadium project includes a 140,000 square foot office tower, a 20,000 seat basketball arena and their support facilities. The arena within the complex will also have the ability to host hockey, ice shows, concerts and family events.

Jan 1, 1997

By Alessandro Bertero, Stefano Valagussa, Filippo Maria, Wesley Schmutzler, Leoni

"Abstract The Deep Mixing Method (DMM) represents a viable solution to improve the adverse geotechnical properties of foundation soils. Differences and the importance of performing pre-construction laboratory and field tests will be highlighted. Comparative analyses and interpretations between the various lab and field stages, along with accumulated information about soil properties and QC results, allowed fine-tuning of the production parameters throughout almost the entire project.Two projects where the US Army Corps of Engineers selected the Deep Mixing Method (DMM) for the required stabilizations, and a third project completed in Italy, will be illustrated:•,?the LPV 111 Project (New Orleans - LA – USA); DMM was used for groundimprovement/foundation strengthening and consequently stabilize and support the burden of the new levee.•,the Rio Puerto Nuevo Project (San Juan - PR - USA); DMM was applied to improve the soils adjacent to a 90” forced sewer main relocation and to improve the soils for the base of a new drainage channel•,the new Italian high speed railway project (Florence Italy); DMM technology was applied to realize a a TBM break in/break out, foreseen originally by jet-grouting.IntroductionThe Deep Mixing Method (DMM) represents a viable solution to improve the adverse geotechnical properties of foundation soils. The effectiveness of working parameters depends largely on the physical and mechanical properties of the soil to be treated. Therefore, well designed laboratory and field test programs, aimed to disclose the interaction between the site-specific soils and the mixing parameters, are essential to achieve the desired end product."

Jan 1, 2014

By Zachary Q. Maassen

The purpose of this paper is to highlight the environmental benefits of properly managing slurry waste as it is generated on site. The following projects will be used to illustrate the importance of proper onsite waste management. Project: Jet Grout Backflow Dewatering The goal was to dewater the backflow directly onsite to produce a dry, solid waste and reusable water. The backflow spoil was pumped directly to the dewatering system as it was generated. Utilizing mechanical separation equipment and flocculation polymer the waste volume was reduced by 44%. Due to the site footprint and high volumes, slurry waste removal and onsite processing were the only two feasible options. Onsite dewatering proved to be the environmentally beneficial option as it eliminated the need for slurry waste hauling and disposal. The benefits of utilizing a dewatering system are listed below: Project: Soil Mixing Spoil Recycling for Slurry Wall Construction In this application the spoils generated contain bentonite mud, cement mixture and organic ground soils. The goal of this project was to process the backflow mixture to recover reusable bentonite mud and separate the soil as a dry, stackable waste product. The treatment system replaced the traditional method of vacuum truck extraction and facility disposal. The environmental benefits of properly handling the backflow is a decrease in fresh water usage, bentonite additive reduction, and the reduction of CO2 emissions. The paper will consist of a project scope, technical equipment and process description, environmental impact reduction calculations and lessons learned for each project.

Jan 1, 2018

By Kam Ng

For bridges or buildings that may be subjected to large vertical and lateral loads, drilled shafts offer an economic foundation solution. While the current drilled shaft design practice is considered adequate, introducing a performance-based approach to designing the drilled shafts will make their design more cost-effective and produce more dependable response. This concept was examined using analysis of 41 drilled shaft load test data from several states. This process identified the challenge with the lack of information from the Osterberg (O-cell) load test method to characterize the full top load-displacement response. When a typical single O-cell is utilized in a drilled shaft test, depending on the location of the O-cell and the geomaterials present along and beneath the shaft, the load test result typically quantifies either the side resistance or end bearing reaching the ultimate load-displacement curve but not both components. This limitation hinders the determination of a suitable shaft resistance as a function of a target top displacement. To overcome this challenge, an improved procedure is proposed for establishing the full load-displacement curve based on data gathered from one O-cell. The method will be presented in the paper for three different cases (i.e., side resistance reaches the ultimate during the test, end bearing reaches the ultimate during the test, and neither components reach the ultimate values). Because it allows the characterization of the full load-displacement curve, the proposed procedure will allow performance-based design of drilled shafts with due consideration to settlement while satisfying the Load and Resistance Factor Design.

Jan 1, 2013

By Haijian Fan

Currently, deep foundation designs for the service limit state are deterministic in nature. The settlements and lateral deflections of deep foundations are calculated by means of numerical techniques whereby the foundation-soil interactions are characterized by discrete load transfer curves such as t-z or p-y curves. The noted deficiency of the deterministic approach is that the uncertainties arising from various sources, such as soil properties and model errors are not considered. To address this deficiency, a performance-based reliability design methodology is developed using Monte Carlo statistical methods. The performance based design criteria are defined in terms of the specified allowable displacement. The input to the numerical solution techniques, including the soil strength parameters, unit weight of the soil are relevant to the generation of the load transfer curves are treated as random field. The well established random field generator algorithm, local averaging subdivision, is used to generate random samples of input, where the mean values, variances, the probability distribution, and correlation structures are required statistical parameters for these random variables. The objective of the performance based reliability design is to determine the optimized foundation dimensions so that the probability of failure is less than the target probability of failure. The probability of failure by the Monte Carlo approach is simply the ratio of the number of unsatisfactory performance to the sample size. A numerical example for laterally loaded drilled shaft is given to illustrate the application of the methodology. The incorporation of the correlation length is shown to be critical for properly accounting for the site soil spatial variability.

By Haijian Fan

Currently, deep foundation designs for the service limit state are deterministic in nature. The settlements and lateral deflections of deep foundations are calculated by means of numerical techniques whereby the foundation-soil interactions are characterized by discrete load transfer curves such as t-z or p-y curves. The noted deficiency of the deterministic approach is that the uncertainties arising from various sources, such as soil properties and model errors are not considered. To address this deficiency, a performance-based reliability design methodology is developed using Monte Carlo statistical methods. The performance based design criteria are defined in terms of the specified allowable displacement. The input to the numerical solution techniques, including the soil strength parameters, unit weight of the soil are relevant to the generation of the load transfer curves are treated as random field. The well established random field generator algorithm, local averaging subdivision, is used to generate random samples of input, where the mean values, variances, the probability distribution, and correlation structures are required statistical parameters for these random variables. The objective of the performance based reliability design is to determine the optimized foundation dimensions so that the probability of failure is less than the target probability of failure. The probability of failure by the Monte Carlo approach is simply the ratio of the number of unsatisfactory performance to the sample size. A numerical example for laterally loaded drilled shaft is given to illustrate the application of the methodology. The incorporation of the correlation length is shown to be critical for properly accounting for the site soil spatial variability.

Jan 1, 2017

By Georg Breitsprecher

The technique of Stabilising Columns (product names are for example "Stabilisierungssaulen" (STS) or "Coplan Stabilisierungs-verfahren" (CSV)) is gradually becoming well accepted for ground improvement. The installation, dimensioning and quality control are standardized by DGGT (German Association for Geotechnique), working committee 2.8, of which until now only part one exists for dry columns. This paper describes the installation and testing of stabilising columns for a ground improvement project. To achieve comparable results in testing both ready mixed concrete and dry binder had been used for production.

Jan 1, 2006

By Terence P. Holman

Micropiles are employed to retrofit existing foundations, including underpinning prior to future construction operations and resupport of existing structures that have experienced distortion and settlement. This paper presents analyses of the two case histories requiring the use of micropiles in these applications. The first case history involves micropiles used to resupport a settled pump station next to an excavation which had suffered basal failure and ground loss. A compression load test pile experienced plunging failure which, after analysis of the strain-gauge data acquired during the test, was attributable to a greater degree of disturbance to the subsoils beneath the site than anticipated. After construction of the micropiles around the pump chamber a synchronized jacking system was used to lift and right the 320 kip chamber structure, followed by resupporting it on the newly constructed piles. The second case history entails the use of micropiles for direct underpinning support of existing columns prior to a utility tunnel installation within an existing high-bay warehouse structure. The design constraint that most significantly affected the successful completion of this project was the desire to bond the new piles into the existing reinforced concrete foundations. As a result of the coring method through the footing, the ultimate bond stress measured during a pullout test was more than twice that assumed in the design. Monitoring of the underpinned columns during trench excavation indicated that the system performance was acceptable. These case histories reinforce the concept that lower capacity micropiles can provide a rapid means to underpin and retrofit existing structures.

Jan 1, 2007

By Leonardo Massone

The p-y method is one of the most popular methods in pile design and has been calibrated for various boundary conditions using numerical and experimental studies during recent years. Most studies on reinforced concrete (RC) piles have included the impact of flexural nonlinearity, (e.g. nonlinear moment?curvature relations) but not considered associated pile shear deformations when deriving p-y curves from field data. Common p-y curves may be better applicable for piles with flexure dominated failures (e.g. piles with free- head boundary conditions). For piles with fixed head boundaries (i.e. rotation restrained piles) shear deformations could be of significant influence. To study this problem, a coupled shear flexure interaction model for axial-bending-shear behavior coded in OpenSees is applied to a 0.61 m flagpole and a 0.61m fixed head pile specimen to investigate the possible influence of shear deformations to the overall pile responses. The surrounding soil is represented by p-y curves derived from prior large scale testing on piles with similar boundary conditions. Analysis results show that for flagpole piles, shear forces and shear deformations were insignificant. Considerable contributions of pile shear displacements and forces were observed for the fixed head pile, with shear displacements contributing up to 40% of the total pile displacement. Results suggest that nonlinear shear deformations for reinforced concrete piles should be considered for fixed-head or similar conditions, and that currently used p-y curves may underestimate the actual lateral pile displacement and possibly lead to unsafe design for the particular boundary condition.

Jan 1, 2011

By Han Xuanjiang

Through whole analysis of static testing piles information of a teaching building, this paper put for ward that when the ratioes of unload rebound amount to residual deformation and to total settlement reach the maximum, the testing load is selected as allowable capacity of single pile by camparing with the settlement in the practical engineering, it is proved that this method fits to practice, for other several projects, its also available. Therefore non-destructive testing pile method was improved, so all the tested piles can be reused as engineering piles.

Jan 1, 1991

By C. T. Christensen

The paper gives an outline of the design, installation and performance of a series of mooring and berthing dolphins for a major ferry berth outside the port of Elsinore, Denmark. The Dolphins are large cylindrical bottle shaped and open ended steel piles vibrated into the sandy seabed. They are subsequently equipped with prefabricated fender units. Vehicle access to the ferry is via a fixed ramp and a semi-submerged linkspan. Supplementary passenger access is via a covered gangway steel bridge from an existing gangway facility to a midship door in the ferry«

Jan 1, 1989

By N. Q. Huy

This paper describes the application of finite element analysis to simulate the static and quasi-static pile load tests in different drainage conditions. The possible effect of excess pore water pressure will be studied from the simulations results. The results show that the drainage condition has effect on the bearing capacity of a pile derived from the quasi-static pile load test. The excess of pore pressure reduces the pile toe resistance while it increases the pile shaft resistance. The factors which influence the effect of excess pore pressure are also discussed.

Jan 1, 2006