Search Documents

By Maurice Bottiau

"Abstract When addressing the performance of deep foundations, many parameters play a role, from adequate soil investigation to performance monitoring and testing. The correct understanding of pile construction, though, remains crucial. After a long period of empirical design and regulations, the last decades have been the ones of theoretical considerations and extensive codes writing. The interaction between technology and design, however, still plays a determinant role. The introduction of hydraulics and the exponential increase in available power on one hand, the miniaturization and the introduction of electronics in control and monitoring systems on the other hand have exerted a major influence on new foundation systems or the evolution and control of existing systems. It appears important to try to take execution related parameters and their control during execution more deeply into account when assessing the final result of the deep foundations and the achieved level of safety and reliability. In this contribution, we will try to analyze how systems, equipment and pile production monitoring and testing can influence the pile performance, and if/how this influence could/should be translated in adapted safety or installation factors. This analysis will run through different categories of piles: driven, augercast and displacement auger piles and bored piles. INTRODUCTIONThe global performance of a deep foundation depends on different aspects (Poulos, 2003):1. Ground investigation2. Design and analysis3. Construction4. Testing5. Performance monitoring6. Remediation and performance enhancementThis paper intends to address the importance of pile construction and the control of it on the final performance of the pile-group of piles. There has been an increasing interest for theoretical analysis over the last 20 years, followed by an increasing impact of regulation and codes. Without denying the importance of the latter, the author wants to point out how installation procedure and project specific parameters can largely influence the reliability of the deep foundation. In this context, detailed and prescriptive standards can miss their objective of intended improvement of accuracy and reliability, but even worse they can adversely impact engineering judgment. In today’s construction world, it is possible to gather installation information which can be of outmost importance for the final deep foundations performance. Therefore, the increase or decrease of installation reliability through adequate pile testing and performance monitoring should be emphasized and should be taken into account in the codes. This is the case already in most advanced codes, but in a limited and insufficiently refined way. After reviewing how codes deal with this issue today, we will show some recent examples of unexpected results due to pile installation. We will try to put these examples into a broader perspective by highlighting some reference and/or recent literature considerations. Finally we will try to summarize how pile testing and installation documentation can increase reliability and attempt to open the debate on how codes could/should allow for more engineering judgment."

Jan 1, 2014

By Eric C. Halpin

"1. Introduction and Backgrounda. In its fundamental form, risk is simply the likelihood of an adverse impact. Expanding on this theme, the Corps of Engineers has broadly defined risk associated with infrastructure as a factor of three distinct elements: a probabilistic assessment of a hazard such as a flood or earthquake; a probabilistic assessment of how the infrastructure performs in the face of this hazard; and a measure of the likely consequences – loss of life, economic damage, environmental impacts – associated with the resulting inundation scenarios.b. The lessons and observations described herein relate to the Corps of Engineers experiences in implementing risk concepts for infrastructure management during the period 2005 through 2013. The Corps of Engineers is a large, decentrally operated and centrally led federal agency that plans, designs, constructs, operates, maintains, and/or manages a portfolio of over 3,000 built dam and levee systems within the United States. The infrastructure in this portfolio is 55 years old on average, and although much of the structures provide for flood risk management benefits, many of the dams deliver multi-purpose benefits. Scale matters – where scale and uncertainty are large, risk concepts provide great opportunity and arrangement for application.c. The amount of organizational change that is demanded for the implementation of risk concepts is considerable and should not be under estimated, but need not be feared if the path others have taken is considered. This paper is, in many ways, an opportunity to step back from the last seven years of implementing risk informed management, check our own azimuth and maturation, and share the purpose and energy behind our own continuing actions. Hopefully, this azimuth check is also beneficial to those that are either considering the use of risk or are in the process of implementing risk concepts.d. Success at managing the massive change related to incorporation of risk concepts will directly affect success of the infrastructure program. The three key organizational elements to consider –human systems such as governance and competencies; policies that outline the who, when, and why of decisions and management; and the processes and technology that outline how work is to be performed - are changed fundamentally. From senior leaders to project team members and all of the people in between, there is a need to discuss, confront, and vet the change and the role people and organizations have in the process. For the Corps of Engineers, with a history of over two centuries, deeply embedded beliefs about infrastructure aren’t transformed over night - the change process is decadal in scope. Given our self imposed “project execution” mantra and corporate objective, risk seemed threatening at first to the cost and schedule of delivering infrastructure projects. In reality, risk concepts have been responsible for savings and cost avoidance of nearly $6 billion over the last three years alone while at the same time justifying increased investment by several fold for the highest risk needs."

Jan 1, 2014

By J. Allan Tice

In the past fifteen to twenty years, the use of drilled piers to support high capacities in coastal plain deposits has become more and more common. With improved construction techniques and better understanding of pier behavior, drilled shafts with capacities of 200 to 500 tons are not unusual. The purpose of this presentation is to review several drilled pier installations from North Carolina to north-east Florida as a means of illustrating the different types of design concepts and installation techniques which are presently being used. ACKNOWLEDGEMENTS The information in this presentation was obtained from work performed by many individuals and companies. The section on limestone socket caissons in South Carolina is an abridged version of a paper prepared by Rob Smith and Neil Gilbert of Law Engineering's Charlotte, North Carolina office, and is used with permission. The section on pier installation in northeast Florida is an abridged version of a paper prepared by Kirk Mcintosh, Tom McDaniel, and Randy Knott of Law Engineering's Jacksonville, Florida office, reprinted here with permission. Additional data discussed in this presentation has been obtained from Farr Foundation Company, McKinney Drilling Company, and Peterson Drilling Company.

Jan 1, 1988

By Michel Bustamante

The occasional substandard performances of continuous flight auger in particular soil conditions have prompted the drilling rig manufacturer to improve the standard CFA in order to reduce its negative effects. A real improvement of interest was the launching of the double rotary CFA system. The promising features of the latter have incited the authors to implement an extensive experimental research on pile constructed using this type of technique but in the specific context of cohesive soils. Short-term static load tests were carried out on a total of 9 test piles of various installation techniques in order to compare the respective performances. The promising features of the double rotary CFA have incited the LCPC & Durmeyer Company to implement an extensive experimental research on this type of pile technique but in the specific context of cohesive soils and more particularly in clayey marls. After load tests completion the research has been completed by an excavation of the double rotary CFA piles. All the collected data concerning the implemented program are reported.

Jan 1, 2002

By S. H. Miller

Biodegradable hydraulic fluids can save tens or hundreds of thousands of dollars in fines and clean up costs in the event of a hydraulic fluid leak or spill. When properly selected, applied, maintained and monitored, a biodegradable fluid will have a long useful life and will protect equipment as well as or better than conventional petroleum based hydraulic fluids.

Jan 1, 2000

By Michael J. Brown

Load testing is important for controlling the quality of piled foundations. The Statnamic test is an alternative to existing testing methods with a load duration that lies between that for static and dynamic tests. Current methods of analysis offer excellent correlation between static and Statnamic tests for coarse-grained soils but often over-predict the capacity for fine-grained soils. Thus a calibration chamber is being used to produce instrumented beds of clay with reproducible properties. A model pile placed in the beds can be loaded at varying rates using a computer controlled servo-hydraulic system. Results from the modelling will be used to improve methods of analysis and govern the design of a full-scale study. Initial results suggest the rate effect can be represented by a power law relating pile velocity and resistance. Statnamic loading of the model pile produced large negative pore pressures in the clay bed.

Jan 1, 2002

By Guo H. Lei

Over the last four decades, barrettes have been ever-increasingly adopted as the foundations for tall buildings and heavy infrastructure projects all over the world. Many findings have been gained from practical applications and theoretical researches. In this article, a collection of literature is reviewed on the installation effects and load-carrying behaviour of barrettes derived from field and laboratory tests and theoretical studies. It covers many aspects, such as the ground deformations and stress changes caused by the installation of barrettes, the shaft resistance mobilisation behaviour, the construction effects on the shaft resistance, and the effects of pile spacing, pile shape and pile group layout on the load-carrying behaviour of barrettes.

Jan 1, 2006

By Li Huimin

In this paper the step of determining the property index and the program of mixture ratio design of stabilizing agent in deep foundation construction are presented. According to the principle of computer simulation, the model and the method of computer simulation for optimum mix design are set up. Also, the precision of simulation results has been estimated and verified experimentally.

Jan 1, 1991

By K. Englehardt

J BERESFORD introduced the subject of the paper which is the use of polymeric slurries to support the sides of diaphragm wall and bored pile excavations during construction. In the opinion of the authors the use of a suitable polymeric fluid offers financial and technical advantages compared with traditional bentonite based slurries. Under quiescent conditions a support slurry must have the following properties. - sufficient viscosity to support the sides of the excavation, to prevent infiltration into soils and to hold loose soil particles in suspension. - when agitated it should thin quickly to assist pumping transfer and cleaning and allow free passage of the grab or drill. - viscosity should be low enough during concreting to facilitate placement but high enough to prevent contamination of the concrete.

Jan 1, 1991

By Mathew Avery, Colby Barrett

In November 2016, a 7.8-magnitude earthquake caused more than 100,000 cubic meters of rock and debris to tumble down and bury the transportation infrastructure below Ohau Point in New Zealand. All routes between the northern and southern portions of South Island were severed. To undertake the rebuilding efforts, the New Zealand government established North Canterbury Transport Infrastructure Recovery (NCTIR) – an alliance to repair the road and rail networks between Picton and Christchurch. NCTIR’s aim was to have the road open by Christmas 2017, but work also continued into 2018 to complete a number of safety improvements along the highway. The presentation will review the initial remediation attempts, the necessity to re-evaluate the original efforts, the need to incorporate techniques that were “outside-the-box” and different from traditional methods, and the logistics and planning that were required to complete the work safely. INTRODUCTION Shortly after midnight on Monday 14th November, a magnitude 7.8 earthquake struck the small South Island settlement of Waiau in North Canterbury, 100km north of Christchurch. The quake was the largest in New Zealand since the magnitude 7.8 Dusky Sound earthquake in 2009 (GNS 2016). While shaking was widespread with over 15,000 recorded ‘felt reports,’ the worst shaking occurred about 50 seconds after the quake rupturing started. The energy of the tremor progressed north over several minutes with surface rupture recorded on a total of 21 faults. The length of all the fault ruptures combined was close to 100km (GNS 2016). The degree of ground shaking was high, recorded as Modified Mercalli Intensity Scale (MMI) Level 8 – Severe. This level of shaking causes considerable damage in ordinary buildings with partial collapse including fall of chimneys, factory stacks, columns, monuments, walls, etc. At a human level, people experience difficulty standing; while furniture and appliances shift. Geologically, the damage depends on the geological setting. In Kaikoura and the surrounding area, especially the coastal highway State Highway 1, north and south of the town, many of the slopes consist of over steepened weathered, fractured greywacke. During the quake, the shaking caused significant and widespread damage with a total of 26 major slips (and many smaller slips); closing both State Highway 1 and the Main North Rail Line between Picton and Christchurch.

Jan 1, 2018

By Aaron S. Bradshaw, Ryan M. Coulson

The offshore wind industry in the United States is slowly emerging with the recent construction of the first offshore wind farm located off the coast of Rhode Island. The turbines at the Block Island wind farm are supported by piled jacket structures, which historically have been used for much heavier oil and gas platforms. Offshore wind turbines have unique design requirements and the axial behavior of the supporting piles under cyclic loading is important to design. Cyclic degradation along the pile shaft can affect the capacity, deformation, and stiffness performance of the foundation and of the structure as a whole. This paper proposes a strain-based approach to estimate the fatigue (or endurance) limit of a cyclically loaded pile that may be applicable to long-term service loading. The method is applied to an existing load test dataset and the analysis results appear consistent with the observed pile response. INTRODUCTION The demand for renewable energy has been increasing in recent decades and wind power has seen a dramatic increase in popularity. In Europe, as of 2017 there were 4,149 grid-connected offshore wind turbines across 11 countries (windeurope.org), many of which are supported on monopile foundations. It wasn’t until recently (2016) that the first offshore wind farm was constructed in the United States off the coast of Block Island, Rhode Island. The project included 5 piled jacket structures founded in terminal moraine deposits. Future offshore wind development along the U.S. eastern seaboard could possibly utilize jacket structures in granular foundation soils. Loads from wave, wind, and turbine rotation induce cyclic loads on the foundation that have on the order of 108 loading cycles over the service life on the structure (Schneider and Senders 2010). Turbines located along the U.S. east coast have the added risk of hurricanes. As shown in Figure 1a, the lateral loads on a jacket structure are transferred primarily as axial compressive and possibly tensile loads on the supporting piles depending on the weight of the structure. The friction along the shaft of the pile can be prone to cyclic degradation, leading to reduced pile capacity and stiffness, and increased deformations. An offshore wind turbine foundation must be designed for a variety of limit states including ultimate, serviceability, and fatigue limit states. For a jacket structure this would include an analysis of the ultimate axial pile capacity, axial stiffness, and axial deformations, all of which can be affected by cyclic loading both under extreme (i.e. storm) conditions as well as long-term service conditions. Axial pile stiffness is needed, for example, to estimate the natural frequencies of the structure as a whole and to assess dynamic and fatigue loads. The structure must be designed such that its natural frequency remains outside the loading frequencies of the waves and turbine blade passing frequencies to avoid resonance. Therefore, prediction of the axial response of the piles is important to the design of these structures.

Jan 1, 2018

By Zia Zafir

Design of the deep foundations for the loads imposed by lateral spread include the estimate of the pressure applied by the liquefied material as well as amount of anticipated displacement. In the absence of a non-liquefiable cover over a liquefiable layer, it is possible to design the foundation system just for the additional pressure applied by the flow slides. On the other hand, if a non-liquefiable layer exists above the liquefied zone, the foundation should be designed for anticipated movements. To completely account for liquefaction and/or lateral spread and their interaction with the deep foundation system, a coupled soil-structure interaction (SSI) analysis should be performed. However, a complete SSI analysis may not be feasible for most of the projects. This paper will present recent advances in analysis techniques and simplified methods to design deep foundations for liquefaction and lateral spreading. In addition, a case history of the Rancho California Bridge in southern California located within 1 km of the active Elsinore fault will be presented. One of the bridge abutments is underlain by potentially liquefiable layers. The pressure applied by the liquefiable layer was estimated to be greater than the shear capacity of the 36-inch CIDH piles designed for the abutment. However, with limited ground improvement and more careful analyses incorporating structural effects of CIDH piles, resulting design and construction resulted in a factor of safety greater than 1 against slope failure. The recommended approach was generally consistent with the recently published, and AASHTO sponsored, NCHRP 12-49 project regarding seismic design guidelines for new bridges and the effects of seismic displacements against bridge foundations.

Jan 1, 2006

By Aminul Islam, Vinay M. Kumar

"About 100 Hectares of land reclamation over the very soft to soft marine clay at Uran Creek in Maharashtra is planned. The depth of marine clay varies from 10m to 24m as observed from the geotechnical investigation. The marine clay was treated with Pre-fabricated Vertical Drains (PVD’s) installed from the elevation of +5.5mCD (chart Datum) and preload/placement of surcharge. A Settlement of soft soil mud under the reclamation was monitored using magnetic extensometer (M) and ground settlement maker (S2). These instruments are installed after constructing working platform at around +5.5m CD. Based on the field instrumentation data, the consolidation parameters were adjusted to match the theoretical and actual settlement plot. The author called this approach as “Back analysis method”. The objective of this paper is to present a case study of instrumented preloading treatment for a thick marine clay deposit. The degree of consolidation in clay strata was determined from magnetic extensometer and ground settlement marker data. Authors also determined degree of consolidation as Asaoka method, Hyperbolic method and Back analysis method and compared the results.INTRODUCTIONExpansion of Container terminal with port buildings, rail container depot, roads and utility buildings at Jawaharlal Nehru Port Trust (JNPT) is planned over a reclaimed land of 100 hectares. Uran creek predominately consists of the estuarine deposit of very soft to soft marine clay. They are characterized by low shear strength, very low bearing capacity and exhibit large settlement when subjected to loading. The additional load causes the significant magnitude of consolidation settlement over a considerable period of time. Thus for development projects on top of soft soil, the postconstruction settlement would be of primary concern.To accelerate the consolidation pre-fabricated vertical drains (PVD) were used. Pre-loading procedure was adopted to minimize the post construction total and differential settlements. PVD’s were installed at 1.0m and 1.2m c/c triangular pattern. Locally available borrow material is used as a reclamation material. The reclamation material has been placed over the existing sea bed level by land based method/end tipping method and created the working platform. The level of working platform is decided based on the tide data and it has been selected such that work should be affected during highest high water level. The PVD has been installed from the working platform and subsequently all the field instruments have been installed from the same level. Five different types of field instruments are installed to monitor ground improvement works."

Jan 1, 2017

By B. C. Slocombe

A large derelict inner city site was regenerated for use as a distribution warehouse. Difficult topography and soils conditions required the adoption of a combination of specialist geotechnical processes. Particular attention was paid to the preparation of the site, programming and capabilities of each technique as additional soils information became available.

Jan 1, 1989

By Markus Schönit

Double rotary drilling combines continuous flight auger drilling with a casing for producing a cast-in-place pile. When producing a pile an outer casing and an auger (hollow auger) rotating inside the casing are driven into the ground in counter-rotation. The outer casing serves to support the surrounding soil and the inner auger excavates the drilling cuttings to the surface inside the casing. After reaching the projected drilling depth concrete is pumped through the hollow stem of the auger and outer casing and auger are extracted. After their complete extraction a reinforcement cage can be inserted in the fresh concrete. Compared to Kelly drilling the double rotary drilling method offers numerous advantages, including, for comparable diameter and length, shorter production times and higher accuracy (pile inclination and excess concrete) combined with increased occupational safety and lower noise emissions. Moreover, pile tests have proved that piles produced by double rotary drilling feature higher axial load-bearing capacities than comparable piles produced by Kelly drilling. This article offers an overview of the basic theoretical principles of double rotary drilling lists the required and currently available machinery and, finally, discusses the results and conclusions of a current jobsite.

Jan 1, 2011

By David J. White

The decreasing availability of land in urban areas, and the increasing demand for urban development is leading to the construction of taller and heavier buildings at increasingly marginal sites. Such structures usually require founding at depth and modern construction methods are making the economics of piled foundations ever more attractive (Salgado, 1995). However, the urban environment is not suited to pile driving. Conventional dynamic installation techniques (i.e. drop hammer or vibro-piling) induce vibrations and settlement in a zone close to the pile, and cause noise and dust pollution. Damage to existing structures resulting from pile driving vibrations is not uncommon (Tomlinson, 1986).

Jan 1, 2000

By Tony Brunger, Abid O. Adekunte, George Munteanu, David Greentree

A number of novel solutions have been proposed in recent years as alternatives to props and tie-backs in deep excavation support e.g. Adekunte (2008), Deschamps et. al. (2008), Adekunte et al. (2010) and Adekunte (2014). A number of these non-standard restraining solutions involve the construction of permanent or temporary vertical or raking buttress piles that are rigidly connected to the excavation support wall at regular intervals along the wall run. This paper chiefly focuses on the design and construction of twin-vertical buttress piles as restraining systems behind or in front of embedded retaining walls. The system essentially relies on the push-pull mechanism that develops between the twin piles, to maintain the overall stability of the excavation support. The paper’s main areas of concentration include; finite element modelling, geostructural design, construction procedure, instrumentation and monitoring that are associated with the application of twin- buttress pile systems. These are supported with project details of three recently completed high-end luxurious residential developments in Greater London, England, on which the twin-buttress pile system was used to restrain the excavation support walls for the basements on the sites. The mode of application of the system varies across the three sites. While the system was adopted as a long term solution behind the retaining wall on one of the sites, it was designed and constructed for temporary use in front of the retaining walls on the other two sites. Instrumentation and monitoring results from all the sites show the non-traditional system to be safe and effective, whilst having significant beneficial effects on construction programme, sequence of works and project cost.

Jan 1, 2018

By Mauricio Terceros, Martin Achmus, Freddy Lopez

The massive use of deep foundations had a remarkable influence in the building industry in the 20th century. Piles and micropiles made possible to erect thousands of civil structures around the world, changing quintessentially the urban and rural landscapes. Especially in urban areas, the ongoing development requires not only new infrastructure, but also to increase the capacity and/or to extend the serviceability of existing structures (buildings, bridges, etc.). Factors such as the change of use of existing facilities or the requirement to comply with updated building regulations confront Civil Engineers with the question, whether to tear down and build new structures, or to reinforce the existing structures from their foundations. Micropiling has enabled designers to come up with technical feasible solutions to retrofit the existing deep foundations, making the structural reinforcement a real option, even under considerable changes in the loading conditions. The following article presents an overview of an intervention project, where micropiles were designed to reinforce the original pile foundation of an existing building, enabling it to be reused with a different structural function. This paper will focus mainly on the analysis of the interaction between the existing piles and the reinforcing micropiles, especially in terms of settlements’ compatibility. Finally, the adopted solution, with its correspondent design considerations and execution process will be presented.

Jan 1, 2018

By Ryan C. Linthicum

A system of steel sheeting and multiple levels of high capacity double corrosion protected soil anchors were used to restrain a major slope failure that occurred at the base of the Watchung Mountains mid-way through construction of a 650,000 SF retail center along Route 22 in Watchung, New Jersey. The implementation of a design-build earth retaining structure was necessary to stabilize and repair the disturbed mountainside in a timely fashion to permit completion of the retail center on a fast track schedule. The tied back steel sheetpile wall was approximately 2,000 feet long and varied in height from 12 to 25 feet. The hillside extended approximately 350 feet above and 600 feet beyond the wall with the main failure scarp extending 50 feet above and 90 feet beyond. The wall was constructed in a top-down manner and required the installation of 475 anchors to resist loads of up to 70 kips/ft produced by the creeping hillside and groundwater flows from both a series of springs and steady state seepage through an inclined zone of fine sand. Incorporation of a unique tie point connection eliminated the need for a waler, facilitating and simplifying modifications to anchor locations based on anchor load test results and conditions encountered during construction. Post grouting also proved to be an essential element in the successful construction. This paper presents the design and the construction methods used to restrain the significant earth lateral loads produced by a slope failure using steel sheeting tied back with high capacity soil anchors with anchor loads distributed to the sheeting through a unique tie point connection on a fast track schedule. Installation techniques, testing programs, and construction quality control are also discussed.

Jan 1, 2003

By Dan A. Brown

The New Mississippi River Bridge (MRB) employed conventional design-bid-build procurement, but the bidding process included the opportunity for pre-qualified bidders to develop and propose confidential Alternative Technical Concepts (ATC?s) for evaluation and approval in advance of bidding. The ATC process provides a mechanism for value-engineering prior to bid, with incentives and opportunities for both the owner and the bidding contractor. The contract described in this paper is for the river bridge composed of a cable-stayed crossing with two pylons and the anchor piers on each side of the river. The Massman-Traylor-Alberici (MTA) team developed a re-designed foundation system for the main pylon and anchor foundations which utilizes their equipment and experience along with field load test measurements to optimize the foundations. The paper describes the experience with the use of the pre-bid ATC process on the project from the perspective of the bidder, and outlines some of the benefits and limitations of this concept with respect to foundation design and construction. Some keys for success are identified and impediments to the effective implementation of the process are described.

Jan 1, 2011