Search Documents

By Wesley Schmutzler

The Deep Mixing Method (DMM) was employed to raise and support the LPV (Lake Pontchartrain and Vicinity) -111 Levee in New Orleans. Even using innovative technologies, the tight schedule to achieve the 100 year elevation by June 1, 2011 was a daunting endeavor. The size and scope of DMM proposed for LPV-111 was on a scale never attempted outside of Japan. Over 1.65 million cubic yards of DMM was installed. LPV-111 is adjacent to the Bayou Sauvage Wildlife Refuge, which is the largest urban National Wildlife refuge in the United States. By utilizing DMM to control settlement and improve stability of the taller levee, side slopes were steepened from the conventional 1V:4H to 1V:2.85H, thus avoiding encroachment into the Bayou Sauvage and reducing the amount of clay needed for the completed levee. The COE utilized Early Contractor Involvement (ECI) for this contract. The ECI process allowed for input from the DMM contractor, TREVIICOS South, in order to optimize equipment resources and material requirements. This paper gives an overview of the extensive DMM requirements for LPV-111 and explains the benefits of the ECI process.

By Sanjeev Malhotra

"This paper presents the results of a pile installation monitoring and performance assessment program for pile foundations supporting 14 piers and 2 abutments of the 1700-ft long bridge crossing over a river in Baltimore, Maryland. Dynamic measurements were conducted during installation and restrike of 16 test piles, one at each support location. The foundation piles were 30-inch diameter, 0.75 inch thick pipe piles at the piers and 24-inch diameter, 0.5 inch thick at the abutments. The piles at the piers were approximately 100 ft long and were designed to carry 260 kips service load with a factor of safety of 2.25. The piles were driven open ended into a variable site stratigraphy containing recent deposits of organic clayey silts near the mudline followed by loose to medium dense sand, with some silt, and then by soil deposits from the Cretaceous period consisting primarily of dense to very dense, poorly to well graded sands and gravels and cobbles, with occasional seams of very hard to very stiff, low to moderate plasticity silts and clays. This paper presents the approach taken to evaluate the driven index piles and to develop criteria for driving production piles. It provides the Engineer with some data on pile driveability in Cretaceous soils in the Baltimore area, soil set-up effect, and an estimate of pile capacity.INTRODUCTIONThe typical approach to pile foundation design and construction should include an indicator pile program with dynamic measurements and a static load test program. However very often paucity of funds and schedule constraints cause an owner to do away with conventional static load testing which can take $25,000 to $100,000 and several weeks per test. This paper examines an alternate (though not equivalent) truncated approach to foundation assessment and presents a case history where this approach was implemented.Dynamic measurements were conducted during pile installation for the 14 piers and 2 abutments of the new 1700-ft long bridge over a river in Baltimore, Maryland. Strain transducers and accelerometers were attached to the pile top during initial driving and restrike of 16 pipe piles. The foundation piles consisted of 30-inch outside diameter, 0.75-inch thick pipe piles at the piers and 24-inch outside diameter, 0.5 inch thick at the abutments. The piles were driven open ended into a variable site stratigraphy. The approach taken to assess the foundation performance included 1) a pre-field wave equation driveability analyses, 2) field pile driving measurements, 3) post-field Case Pile Wave Equation Analyses (CAPWAP), and, 4) revised wave equation analyses based on field and CAPWAP data. The following sections describe in greater detail each of the steps taken to assess foundation performance and the results obtained."

Jan 1, 2005

By Osama A. Safaqah

Driven plate anchors can be used to hold in place large bridge caissons during floating construction. Their small size and simple method of installation make them a very cost effective alternative to other direct-embedment, gravity, and drag anchors. The geotechnical design of plate anchors involves the anchor geometry, embedment, drivability, and proof testing. This paper describes the experience gained with plate anchors used during construction of the new Tacoma Narrows Bridge. For this project, the anchors had to be driven in dense to very dense sands, and had to resist large forces from 7-9 knot currents.

Jan 1, 2013

By Emad Farouz

The resistance of very dense glacial outwash formations consisting of sand, gravel and cobble formations can be quite high, and techniques for measuring the strength and deformation properties often cause engineers to underestimate the strength of these layers in drilled shaft design. More realistic measurements of this dense formation can be achieved with slotted steel casing pressuremeter tests. To minimize disturbance and achieve accurate measurements, drilling a pilot hole prior to probe insertion is necessary. Characterizing geologic formations that contain significant amounts of gravel and cobbles is challenging because of scale factor. Inserting a standard pressuremeter probe into this formation without damaging the membrane is difficult. This paper presents a case study for the IR-75 project in Dayton, Ohio, USA, where these dense materials were characterized using a slotted casing pressuremeter, optimizing design by providing more realistic properties of these materials.

Jan 1, 2006

By Teresa M. Bodas Freitas, Arianna Lupattelli, Peter J. Bourne-Webb, Diana Salciarini, Martina Zito, Donatella Sterpi

The thermomechanical response of thermally-activated (TA) piles under monotonic thermal loads is quite well understood and the remaining uncertainties relate to the effect of long-term, cyclic loading of individual TA piles and pile groups. Recent studies undertaken by the authors have provided insights into the behaviour of TA pile foundations undergoing cyclic thermal loading. Despite their simplicity, the analyses show that key aspects of the observed response of piles in sand, under cyclic thermal loading can be reproduced, providing confidence in the outcomes of the analyses. The studies examined isolated piles and pile groups, and concluded that irrecoverable thermally-induced settlement may be mitigated through the choice of an appropriate margin of safety on the pile shaft resistance under service mechanical load conditions, and the maximum thermal stress can also be readily estimated. This paper consolidates these works and provides guidance regarding the safe geotechnical and structural design of the piles, then looks towards the remaining issues around the safe provision of thermally-activated pile foundations.

May 1, 2022

By Marius B. Wechsler

A mathematical analysis is developed for the determination of the cases when HP-piles might be replaced by precast concrete piles. The analysis focuses especially on the "integral abutment-bridges" which are used on large scale in the Great Plains of the United States of America, The theoretical considerations are illustrated by a numerical example.

Jan 1, 1992

By John Y. L Chen

This paper presents full-scale instrumented pile static compressive and tensile load tests to be conducted in the area of Pearl Harbor, Hawaii. Thousands of piles have been installed to support the existing piers and wharves in the Pearl Harbor area. Due to the absence of bedrock within practical depths, most of the piles use combined friction and end bearing. A new 925 feet (282 meters) long and 50 feet (12 meters) wide reinforced concrete wharf supported on pile foundation is planned. This paper will present results of soil investigation, laboratory testing, dynamic load tests during indictor pile driving and static pile load tests. The subsurface conditions consist of soft harbor sediment, young alluvium deposit, volcanic tuff rock formation and stiff old alluvium deposit. The load test piles consist of 20-inch (508 mm) square and 24-inch (610 mm) octagonal pre-stressed, pre-cast concrete pile and instrumented with embedded strain gauges. The length of the piles ranges from about 50 to 125 feet (15 to 38 meters). The test pile program consists of probing, driving indictor piles, dynamic load tests during indictor pile driving and static load tests. The standard loading procedure method was used during static pile load tests.

Jan 1, 2002

By Richard Schmidt, Lijun Deng, Mohamed Abdelaziz, Weidong Li

Helical piles are widely used as a foundation supporting a variety of different structures. Understanding the axial behaviour of helical piles is required to confirm the engineering design. Helical pile research is often conducted in the field, but this method can be prohibitively expensive in some cases. Geotechnical centrifuge modeling offers an alternative method for the helical pile research and practice. A series of axial load tests of helical piles installed into cohesive soils were conducted on the geotechnical centrifuge at the University of Alberta. The objective was to investigate the effects of inter-helix spacing and soil strength on the axial behaviour of helical piles. Four types of aluminum model helical piles including one single-helix pile and three double-helix piles with various inter-helix spacing ratios were tested. Both compressive and tensile loading tests were conducted. All model piles were instrumented with multiple strain gauge stations. The clay had an undrained shear strength of approximately 50 kPa and 120 kPa. The test results indicate that there is a transitional failure mode between the two widely recognized failure modes, i.e., individual plate bearing and cylindrical shearing. The shaft adhesion was significantly reduced by the helix. Axial capacities were comparable to the field test results.

By Brain E. Ladd

A load test program was performed on two auger cast piles constructed in the Inner Coastal Plain geology of North Carolina. Both test piles were installed through Coastal Plain deposits and into underlying Piedmont residual soils; one test pile was embedded into partially weathered rock (PWR). The recommended 100-ton design load was confirmed by a test program that included instrumenting the piles with strain gages. The two piles performed differently during the load tests due to the effect of embedment into PWR. Loading Test Pile No. 1, which was not embedded into PWR, to failure at about 230% of the design compressive load allowed for evaluation of the mobilization of the ultimate shaft and end bearing resistances. Mobilization pile resistance was evaluated by comparing shaft and end bearing resistances to top of pile deflection (?) normalized by the pile diameter (D). For Test Pile No. 1, the ultimate average shaft resistance was achieved at ?/D of about 7.5% and ultimate end bearing resistance at ?/D of about 9.5%. Test Pile No. 2, embedded into PWR, achieved a ?/D of only about 4% at 200% of the design load and was not loaded to failure. Shaft resistance was mobilized at a different rate within each individual geologic layer, i.e. ultimate shaft resistance did not occur simultaneously for all geologic layers. As the available total shaft resistance was exceeded and end bearing mobilized, the unit shaft resistances reduced from the peak values. A modified Davisson offset using ?/D of about 6.5% appears applicable for evaluating the ultimate capacity of auger cast piles in the Inner Coastal Plain.

By Chu E. Ho, Alfredas Daugiala, Nicola Ebanks

"The construction of an ancillary structure for the new Second Avenue Subway Line in Manhattan, New York City involved a deep excavation in highly variable rock conditions adjacent to a fragile masonry building. The maximum difference between the lowest and highest rock elevations was about 30 feet, which posed a problem for the installation of secant piles that formed the supporting retaining wall for the excavation. At certain areas, the rock levels were higher than the top of the invert slab of the ancillary structure. To avoid disturbance to the adjacent fragile building, the secant piles were fully cased for drilling through the overburden soils and the rock sockets were formed using non-vibratory technique. This paper discusses the design and installation details of the secant pile wall and the contingency measures that were considered to mitigate the highly variable rock conditions. Monitoring of the adjacent fragile building showed that impact of pile installation were controlled within tolerable limits and safety of the building was not compromised.INTRODUCTIONThe 96th Street Station forms part of the newly constructed Second Avenue Subway Line on the East side of Manhattan Island, New York City (Figure 1). During construction of this station, several deep excavations were carried out adjacent to existing fragile buildings (Arksman et al. 2012, Grigson et al. 2016). These fragile buildings were typically four to five stories high, with a single rubble wall basement supported on timber piles or seated directly on the fill. The timber piles were often found to be in a poor condition and connections to the footings were compromised due to rotting of the timber within the zone of water table fluctuation. Several of these fragile buildings had to be strengthened and underpinned to improve the stability of the structures prior to commencement of excavation for the new subway station box (Trabold et al. 2012, Ho and Pena-Iguaran, 2013). The situation was most challenging at Ancillary Buildings 1 and 2 located at 93rd and 97th Street respectively, where secant pile walls were located merely 2 feet away from the adjacent property line, due to architectural space constraints. While mitigation of excavation induced ground movements can be controlled by the adoption of a stiff excavation support system, a more concerning factor was the uncertainty associated with the impact of the secant pile wall installation on the stability of the existing fragile buildings. This was particularly difficult at Ancillary 1 where the secant piles encountered highly variable rock levels that intruded into the excavation space. The following sections discuss the design and installation of the secant pile wall and contingency measures that were considered at Ancillary 1."

Jan 1, 2016

By Achyut Kumar Allady, Praveen Arumughan

NCHRP Synthesis 418 (2011) entitled, “Developing Production Pile Driving Criteria from Test Pile Data” details the occurrence of dichotomy between pile Skin resistance and pile Tip resistance mobilizations at different times for different hammer blows during pile driving operations. With increasing usage of High Strain Dynamic Testing (HSDT) the engineering community started paying more attention to this occurrence of dichotomy resulting in overdriving, pile damage, increased claims, and loss of time. To overcome the dichotomy limitations of HSDT, NCHRP recommends, “the use of superposition to combine the back-calculated tip resistance from a blow on initial drive or from redrive with the back-calculated skin resistance from the early blows at the beginning of restrike”. However, the current practice of external mounted gauges and signal matching for a single blow are unable to evaluate independently the Skin resistance and Tip resistance to achieve the goal of determining the optimum Total Pile Capacity using the superposition. This paper discusses advancements of science and technology with sensors embedded at the pile top and pile tip, the data collected is analyzed by the state-of-the-art FDOT Method to determine Skin and Tip resistances independently for every blow. Independent Tip and Skin resistances each with a Resistance Factor can be summed up to obtain optimum Total Pile Capacity. Additional benefits of determining independent Skin and Tip resistances include obtaining lost skin capacity due to scour, due to pre-drilling/preforming and uplift tension capacity. Furthermore, the benefits of embedded sensors include increased quality control/quality assurance through 100% testing, accelerated construction, life cycle monitoring and asset management.

May 1, 2022

By Mario Carnevale, Myles Danforth, Michael Oakland

The cost and overall effectiveness of foundation design depends on a robust characterization of the subsurface geologic setting. It is common practice to formulate deep foundation design from subsurface geologic characterization based on boring programs. The confidence level of geologic characterization is directly related to that of geologic interpretations, which are based on the spatial sampling pattern of boreholes relative to the complexity of the geologic setting. This paper presents a case history illustrating issues that arise during pile construction from over-simplified geologic characterization, the challenging steps taken to improve the subsurface geologic model, and the effect of additional characterization efforts on the pile foundation program. The seismic characterization methods used include multi-channel analysis of surface waves (MASW) and seismic refraction.

By Bengt H. Fellenius

Session 2, Deep Foundation without Soil Excavation, has attracted no fewer than 22 papers dealing with subjects from soil improvement by grouting, injection, and deep mixing techniques through vibroflotation and special piles, including aspects pertaining to conventional driven and bored piles. In the short time available, it is not possible to both do justice to the papers and provide a critical review of the state-of-the-art. Instead, to meet the objective of making the next half hour worthwhile to the audience, I have chosen to comment on a few special points brought forward in the papers and thereafter to discuss more in detail a couple of aspects I have deemed to be of general interest. Four papers deal with jet-grouting, injection, and deep mixing techniques: DOMSKI, J. J. Reinforcement of subsoil under the foundations of historical buildings in Cracow using deep injection technique. RESTELLI, A. B, BERTERO, M., and LODIGIANI, E. Deep mixing technology to improve the bearing capacity of a very soft clayey soil under an earth embankment.

Jan 1, 1994

By Roy Peratrovich

An innovative cost-saving design for a 1,100 ft bulkhead on the Tanana River at Nenana in central Alaska won Alaska Construction & Oil magazine's Construction Achievement Award. The designers utilized materials available nearby at low cost. They planned sheet pile enclosures, self-anchored back into shore without cell closures. They made it practical for inexperienced local workers to do the building. And they completed the project on time and below a reduced budget.

Jan 1, 1985

By Lucien P. Weber

Over the last few years, increased customer demands as well as strong competition from substitute materials have accelerated the development of advanced technologies to improve both the performance and the cost-effectiveness of steel H-piles. On the material side, the development of an in-line heat treatment, combined with the most advanced steelmaking and rolling techniques, allowed to create a new generation of high-strength low-alloy steel grades, called HISTAR, achieving yield points up to 500 MPa (~72 ksi) and yet maintaining excellent weldability properties thanks to a low carbon equivalent. The topic of this paper is to illustrate the performance of H-bearing piles in HISTAR steel grades. In 1989, a major test program was started at different locations in Hong Kong, which is renowned for its difficult soil and severe driving conditions. After the successful completion of these tests, the HISTAR bearing piles were accepted by the local building authorities. Thanks to their cost-effectiveness, the HISTAR bearing piles have subsequently been used with great success in areas with appropriate soil conditions, especially in Asia and more recently in Europe.

Jan 1, 1997

By Daniel Mageau

Ground freezing has been used for over 100 years to provide shoring and ground water cutoffs for hundreds of projects worldwide, including drilled shafts, tunnels and cofferdams. Typically, these cases involved difficult soil/water problems where ground freezing was likely the only solution. This paper discusses a recent ground freezing project where a frozen soil wall was used for a more conventional problem. A 4-foot-thick frozen soil wall was used to provide shoring and groundwater cutoff for a 20-foot-deep excavation during construction of a cast-in-place concrete storm water detention vault. The site is located along the northbound on-ramp to I405 from westbound SR522 in Woodinville, Washington. The frozen soil wall was successfully formed in soils consisting of till fill over soft organic silt and loose saturated sand in about 3 weeks. The depth to ground water varied from about 4 to 8 feet over the site. The unfrozen soil inside the frozen soil wall was excavated vertically to the frozen soil boundary. The vertical excavation remained open for approximately 2 months with no dewatering required. On one side, fully-loaded dump trucks and other construction equipment operated within 6 feet of the wall face with zero wall movement. This paper addresses the construction issues related to installation and operation of ground freezing shoring. The overall wall performance of the frozen soil wall as well as basic geotechnical design issues are also discussed.

Jan 1, 1998

By Donald A. Bruce

Various types of contemporary Deep Mixing Method (DMM) techniques have been used in the United States since 1986. Such techniques owe their origins to Japanese and Scandinavian developments, which began almost three decades ago. The growing demands of urban infrastructure development and rehabilitation have created a very active and rapidly expanding market demand in the United States especially since the early 1990s, and there is a clear need for a new and fundamental review of the surprisingly large number of DMM techniques that are being used domestically, or are available in other parts of the world. Following a summary tracing the historical development of DMM, and a generic classification of applications, the paper provides a review of each of the many different proprietary methods, which the authors have identified during preparation of an international survey funded by the Federal Highway Administration (FHWA). Data are also provided on commercial aspects of the various DMM techniques worldwide.

Jan 1, 1998

By K. Kawakami

In Japan, pile foundations have been used extensively for buildings, bridges and port facilities. A large number of steel pipe piles were first used in the 1960's and the amount of steel used in foundations increased by 1973 to one million tons. This report describes current practice in the actual use of large diameter and long steel pipe piles in Japan, related to their performance: including consideration of pile size, hammer types used for driving the results of field tests measuring stress occurring in the piles and the driving formulae currently being used in practice in Japan.

Jan 1, 2010

By George Moses K, Mahendran K

Grouting is performed in rock masses in order to increase its strength properties and also to reduce the seepage. In the design of underground structures such as tunnels or caverns located in weak rock masses, grouting plays an essential role. Grouting is a complex process demanding high degree of skill and knowledge in understanding of grout flow and requirements for certain geological conditions. This paper discusses the design process for grouting in rock masses adopted for a cavern project and the practical difficulties faced during the execution at site. The design parameters of grouting includes the injection pressure, grout material properties and stopping criteria. The paper also discusses the various tests performed at site to evaluate the efficacy of the grouting process which was initially defined based on the design and previous experiences. The final grouting scheme suiting to the present geological condition is arrived based on the test results. The practical difficulties faced during the execution and the measures taken to overcome these are discussed in detail. This work shows the importance of state of art in the development of a grouting process based on geological and hydrogeological conditions prevailing at site and can be helpful in grouting design for weak rock masses.

Nov 1, 2022

By Kenneth Gavin

The accurate prediction of the shaft capacity of drives piles in sand continues to present problems for foundation designers. Research in this field has been carried out for many years and has yielded a wide range of design approaches -some of which have been shown by recent experimental work to be based on questionable assumptions. This Paper reviews some of the current popular design methods for piles in sand in the context of recent information obtained from high quality field tests conducted by institutions such as Imperial College London. A database of driven piles in cohesionless soils has been compiled from well documented (and reliable) case histories that have been reported in the literature. The measured shaft capacities of the piles in this database are compared with predictions made by the various methods and an assessment is made of the predictive performance and reliability of each method

Jan 1, 1996