Search Documents

By Tu Bao

HP-Pile foundations are the most favorable type of foundations for bridges because of their constructability, versatility with regard to subsoil conditions, and settlement controllability. For many years, bridge engineers have puzzled over the most economical way to orient HP-Piles: Should the strong axis be oriented in the longitudinal direction or in the transverse direction? The accurate design of foundations may considerably reduce construction costs. In order to answer this question, 3-D finite element models will be set up to analyze the effects of pile orientation on bridge behavior. Because seismic loading usually controls the structural design in seismic zones, it is important to investigate the effects of pile orientation under such loading. HP-Piles are designed conservatively due to the uncertainty of the dynamic soil-structure interaction during earthquakes. For the bridge substructure, the soil?s stiffness plays an important role in load distribution as the soil and piles act as a combined system to resist the seismic loading. The dynamic soil-structure interaction mechanisms of bridges in both the longitudinal and the transverse directions will be investigated through the use of 3-D finite element models. The numerical models will realistically simulate the soil-pile-abutment-wingwall-superstructure system subjected to seismic loads. Nonlinear soil springs will be employed to model the non-elastic soil behavior. The analysis will provide theoretical support to the design practice. KEYWORDS: HP driven piles, finite element, pile orientation, soil-structure interaction

By Shahid Islam, Lucian Bogdan

"The maintenance of infrastructures has been of particular concern to the engineering community. As the world’s infrastructure expands and existing infrastructure ages, monitoring and evaluation of the structures have become more critical than ever. A large number of retaining walls, tie backs, slope stabilizations and piles are designed using pre-stressing steel. Many piles and drilled shafts are designed using reinforcing steel. There are few testing methods available to assess these tension and compressive forces. High cost, complicated equipment and limitation of space often prevent these methods from being implemented. DYWIDAG-Systems International (DSI) has been involved in the development, testing and utilization of DYNA Force® sensors to measure the force in the anchors during construction and at any time during the lifetime of the structure. They can be used for bare, epoxy-coated, galvanized and greased-sheathed steel in the bonded, un-bonded, grouted or un-grouted length of the anchor. The sensor is robust and requires no maintenance. Sensors have received attention in terms of accuracy, performance, ease in installation, durability, and cost effectiveness. This paper describes its application in tie-back and anchor force monitoring of retaining walls and bridge abutment and compression forces in drilled shaft reinforcing steel where the data were collected manually, automated and remotely.INTRODUCTIONOur infrastructure is expanding and the existing infrastructure is aging. Some structures are expensive to maintain and some occasionally fail. There is a large demand for implementing health monitoring of structures. Many tie-backs, retaining walls, dams and other geotechnical structures are post-tensioned and many of them need repair using a post-tensioned system. On many occasions during construction and service life of the structure, it is useful to know the force in the post-tensioning and anchor system. Many piles and drilled shafts are designed using reinforcing steel and the compressive forces in reinforcement are unknown. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive, and the accuracy varies depending on the method used.The elasto-magnetic (EM) technology is a novel approach to monitor forces in steel elements. The DYNA Force sensor is built based on EM technology (See Fig. 1). It is composed of a primary coil and a secondary coil (sensing coil). By passing current through the primary coil, ferromagnetic material is magnetized. The sensing coil picks up induced electromotive force that is proportional to change rate of applied magnetic flux (Faraday's law) and relative permeability. As permeability of core changes, output voltage changes. The output voltage is calibrated to measure the force. A readout unit is designed to magnetically energize the steel through the sensor and measure the response of the steel to the process. The readout unit then converts the response into a direct force reading. The sensor has an embedded thermistor which allows for temperature compensation. Due to the diversity of the magnetic property of steel, calibration is done for each type of steel allowing the sensors to perform at their highest accuracy."

Jan 1, 2017

By Terrence M. Carroll, Chu E. Ho, Dimitrios Niarchos

"Construction of the new extension to Terminal 4 at John F Kennedy International Airport in Queens, New York involved the application of tapered piles for foundation support. Initial design based on past load testing experience had indicated that a pile depth of 65 feet was necessary to achieve a capacity of 394 tons. However, piles with a single length of 62 feet were ordered and installed, which led to marginal performance of the piles. This paper presents the technical considerations for mitigating the situation based on a systematic review of three preliminary pile load tests and dynamic capacity measurements on the shorter piles. Consideration was given to the long term gain in capacity of tapered piles due to set up in the Glacial Sand. The observational approach to the evaluation of piling performance adopted on this project resulted in salvaging many piles which failed to comply with the specified driving criteria. It was acknowledged that a more prudent course of action was for the Contractor to have ordered more appropriate pile lengths that allowed for potential variation in soil conditions across the site. The 4.6% saving in pile material did not warrant the effort that was required to mitigate the 39% of installed piles that did not meet the specified driving criterion.INTRODUCTIONAn expansion project at John F. Kennedy International Airport in Queens, New York involved the Phase 2 extension of Concourse B at Terminal 4. The site consists of 4 to 5 feet of pavement over about 10 feet of hydraulically placed sandy fill. Below this is a layer of marsh deposit, comprising of soft organic clay and peat, up to about 11 feet thick. Beneath the marsh deposits is a deep layer of glacial sand which extends to well over 100 feet below ground. Figure 1 shows the typical subsurface profile at the site. The new structures were supported on 223 steel tapered piles. The piles consisted of a straight steel pipe 18 inches in diameter and 0.375 inches thick, with a 25 feet long tapered bottom section (diameter varying from 18 inches down to 8 inches at the pile toe). The piles were first driven to the founding depth and subsequently in-filled with concrete. The concrete strength (fc) specified was 4,500 psi and the yield strength of the steel piles (fy) was 50 ksi. Initial pile design, based on earlier experience with static pile load testing for Phase 1 development at the same terminal, indicated that a pile length of 65 feet was necessary. However, piles with a single length of 62 feet were ordered and installed by the Contractor, leading to marginal performance of the piles. This paper presents the technical considerations for the adoption of alternative pile driving criteria, based on a systematic review of the preliminary static load test results for the present site and PDA measurements obtained during pile installation, in order to accommodate the capacity of the shorter piles."

Jan 1, 2017

By Luo Yang

It has been known that after initial pile driving, pile capacity gain over time (set-up) could constitute a significant portion of the total pile capacity. In the past, there has been very little guidance for incorporating pile set-up capacity in design. This may be due to large uncertainties involved in predicting the pile set-up. A comprehensive statistical database is developed to describe the increase of pile axial capacity with time, known as set-up, when piles are driven into sand. Based on the collected pile testing data, pile set-up is significant and continues to develop for a long time after pile installation. The statistical database shows that a lognormal distribution can be used to describe the probabilistic characteristics of the predicted set-up capacity using Skov and Denver?s equation. The main objective of this paper is to incorporate the set-up effect into a reliability-based Load and Resistance Factor Design (LRFD) of driven piles in sand. A First Order Reliability Method (FORM) is used to derive separate resistance factors that would account for different degrees of uncertainties associated with the measured short-term capacity and the predicted set-up capacity from the proposed semi-empirical equations. The incorporation of set-up effects in the LRFD helps improve the prediction of the total capacity of driven piles, resulting in more economical design. A practical design procedure within LRFD framework to incorporate the pile set-up effect is outlined at the end of the paper.

Jan 1, 2006

By Charbel Khoury, Kwabena Ofori-Awuah, Kofi B. Acheampong

"Following heavy rains in spring of 2014, Prince George’s County officials issued a mandatory evacuation for homes in the Piscataway Hills subdivision of Fort Washington, Maryland where a landslide along a 1700-foot hillside destabilized homes, collapsed the single access road, and resulted in water and sewer mains break. Forensic investigations, including geologic assessments, test borings and in-situ Cone Penetrometer and Dilatometer soundings, were performed to evaluate subsurface conditions and provide stabilization options for the roadway and slopes. Post-failure ground movements were monitored using inclinometers. Critical failure planes were identified within the underlying 30-foot thick Marlboro Clay formation, a known geologic hazard with historic occurrences of landslides and slope failures.This paper discusses the remedial design for stabilizing the landslide and 60-foot hillside slope failure, and protecting the roadway. Amongst several feasible options, driven piles were selected in consultation with the County and retained contractor based on cost, environmental impacts and site constraints. Constraints included private ownership of hillside slope, upslope buildings safety; deep-seated failure, relocation of underground water and sewer mains, and accelerated construction schedule.Pile design included global slope stability analyses and lateral pile analyses using several loading configurations to optimize pile geometry and spacing, and determine a value-engineered design satisfying both serviceability and strength limit states to achieve long-term stability with factor of safety of 1.3. Soils within the active landslide plane were assumed to provide no resistance, while soils below the failure plane provided lateral resistance. This stabilization scheme, which extended along the 1700-foot roadway section and toe of hillside slope area, consisted of 410 steel HP16x141 piles in two to three rows driven to depths between 60 and 70 feet below the Marlboro Clay stratum at 5 to 7-foot spacing."

Jan 1, 2017

By Francisco A. Flores, José L. Aguirre, Héctor A. de la Fuente, Erika Bernal, Jorge Arroyo-Esquedla

This paper presents the analysis, design, and construction of soil improvement for storage tanks foundation support at a site in Tabasco, Mexico. A total of 980 Rammed Aggregate Piers of 12.5 m in length and 0.5 m in diameter were designed and constructed to support four storage tanks. The soil conditions at the site generally consist of loose to medium dense silty/clayey sand to about 8m depth, underlain by very loose to medium dense silty/clayey sand with seams of very soft clay. The use of Rammed Aggregate Piers induced densification of the soil to increase its stiffness and reduce the liquefaction potential to control both static and dynamic induced settlements. Standard Penetration Test (SPT) and Cone Penetration Test (CPTu) explorations were performed prior to and post soil improvement to compare the liquefaction potential and the Factors of Safety associated with the two conditions. Finally, the soil improvement installation rate is presented. Soil improvement using Rammed Aggregate Piers represented a suitable alternative to support storage tanks foundation in potentially liquefiable areas.

Oct 1, 2022

By Timothy C. Siegel

Given that piles are composed of different materials and installed using a variety of methods, ASTM D 1143/D 1143M-07 Standard Test Methods for Deep Foundations Under Static Axial Compression is justifiably general so that it has as many applications as reasonably possible. There are aspects of the test setup, the test procedures, and data interpretation for instrumented piles (some of which are specific to augered cast-in-place piles) that are either not discussed in detail in this ASTM standard or are not addressed at all. Specifically, the use of variable time hold times can obscure the shape of the conventional load-deflection curve, as well as, influence the interpretation of the ultimate pile capacity. Unload-reload cycles induce additional non-uniform internal axial loads within the pile which complicate interpretation of the strain gage data and increase the potential for errors. Attempts to maintain a constant top load during the hold period can lead to operational difficulties in taking measurements and are technically unnecessary. Residual load has been shown to develop in cast-in-place piles and can significantly influence the axial load distribution as interpreted from strain gage data. The stiffness of cast-in-place piles has been observed to vary with the measured strain, and a constant modulus, as provided by correlation with the unconfined compressive strength of the grout, may lead to a significantly different interpretation of the axial load distribution.

Jan 1, 2010

By Madhira R. Madhav

In an alluvial deposit consisting of layers of sandy silt with clay and kankar nodules, driven cast in situ piles are provided. The piles end on a stiff bearing stratum To verify the available design capacities, compression, pull-out and lateral load tests are conducted in situ. The elastic continuum approach is used to estimate the equivalent modulus of deformation of the deposit. A comparison is made of the values from the three types of tests.

Jan 1, 1996

By K. Rama Sarma

Piles are frequently subjected to lateral forces and moments in addition to vertical forces and hence the piles have to be designed for both lateral loads as well as vertical loads. In the design of such pile foundations, two criterias must be satisfied. First an adequate factor of safety against ultimate failure and second, as acceptable deflection at working loads. In this study the work has been carriedout to study the lateral deflection pattern of the pile. The solutions to the problem primarily depend on soil modulus. Equations for computing the values of slope, deflection and coefficients for many types of soil conditions have been developed for static loading for long piles. As analysis part is not available for the above methods for the values of depth coefficients in the tables. It is required to go for linear interpolation which is not valid and highly unreliable. In this present method, coefficients can be obtained for any value of depth coefficient (z) with simple calculation. The present method is very concise and allows one to ana­lyse any type of pile with varying depth coefficient (z) even without the availability of any practical data regarding applied lateral load (P1) and moment (M1).

Jan 1, 1996

By Paul J. Axtell

Two new railroad bridges in Kansas City, Missouri are founded on drilled shafts embedded into the soil and underlying shale. The uncertainty arising from the non-homogeneous, anisotropic nature of most shales, and the variability of shales across the U.S., makes it a difficult material to assign appropriate design properties. As was the case on this project, the uncertainty of foundation performance in shale can lead to overly conservative designs, particularly with drilled shaft foundations. An extensive Statnamic axial testing program was performed to verify that the load-settlement behavior of the drilled shafts would be acceptable for the intended railroad traffic. Axial Statnamic testing was applied in three increasing cycles of 927 kips, 1007 kips, and 3177 kips, respectively. The maximum movements recorded at the shaft head during each of the loadings were 0.052 inches, 0.062 inches, and 0.257 inches, respectively. The loads applied in each of the respective Statnamic tests were not sufficient to reach the capacity of the shaft; so direct comparison of measured and calculated capacities is not possible. However, evaluation of the estimated design capacity can be accomplished based on results from the Statnamic testing program by utilizing normalized load transfer relations presented by O?Neill and Reese (1999). Such comparisons necessarily require extrapolation of the data measured in the Statnamic tests following typical load-displacement response. Results indicate the Kulhawy and Phoon (1993) method for estimating side resistance in Pleasanton shale rock sockets, assuming a smooth socket, appears to agree well with observed behavior during Statnamic testing. Accordingly, the O?Neill and Reese (1999) method for estimating the toe resistance in intermediate geomaterials, assuming cohesive rock with Rock Quality Designation (RQD) between 70 and 100, appears to agree well with observed behavior during Statnamic testing. Finally, based on Statnamic testing at varying load magnitudes and normalized curves developed by O?Neill and Reese (1999), the contribution of side resistance to the capacity of a deep foundation can be determined assuming no load is transferred to the base of the foundation during lower magnitude testing. Furthermore, higher magnitude testing can provide a means to evaluate the accuracy of design end bearing calculations.

Jan 1, 2006

By Musbah A. Hasan, Ahmed M. Nasr, Fauzi Jarushi

Many transmission towers, high-rise buildings and bridges are supported by piles. These structures may be subjected to large lateral loads. Therefore, experimental investigations on model piles under lateral loads were conducted in uniform dry sand. Small-scale model tests were carried out considering the influence of pile length, pile diameter, sand density, roughness of pile surface and vertical load on the lateral resistance of a pile. Furthermore, the effect of pile load eccentricity (e/L) on the ultimate lateral resistance was studied. Investigations, of the influence of various parameters on the magnitude of the coefficient of subgrade reaction (nh), were also performed. It was found that the lateral load capacity of piles increases with increase in pile length, pile diameter, pile surface roughness and increase in the sand density. The results also showed that the coefficient of horizontal modulus of subgrade reaction, (nh), decreases with deflection increase. From the results, the coefficient of subgrade reaction for a smooth pile embedded in medium dense sand would decrease by (134%) when the lateral pile head deflection (yg) changes from (2% to 5%) of pile diameter.

Jan 1, 2017

By Liu Run, Jia Zhao-lin, Yan Shu-wang

"Piles with diameter larger than 2m in engineering can be defined as large diameter pile, and piles used for oil platform foundation in Bohai Gulf, are usually over 100m long and 2m in diameter. Such long piles have to be manufactured by segments before installation, because of transformation and hoisting difficulties. The segments of the pile are assembled by welding during installation one to another. Normally, assembling two pile segments takes one day or even a longer time, which mainly depends on construction conditions. After pile segment assembling, it proves to be difficult to restart the successive penetration. The mechanism of pile refusal is discussed and the process of driving a segmented pile is simulated with a finite element program. The calculating results show that, when the stick-up stability was satisfied, increasing the length of the last segment of the pile and assembling the pile segments when the pile tip penetrates into a clay layer could greatly ease the difficulty of driving the pile. Furthermore, cutting down the pile extension time is also one of the most effective measures to minimize the refusal risk.1. InstructionIn recent years, more and more oil platforms with six or eight legs have been adopted in Bohai Gulf, China. The leg piles with diameters of 2m or more have to be driven to about 100m below the sea bed. Such long piles have to be manufactured by segments before installation, because of transportation and hoisting difficulties. The segments of the pile will be assembled during installation, in which a successive segment will be attached to a formerly penetrated one by welding (Fig.1). The assembling work often takes one day or even a longer time."

Jan 1, 2014

By Abid O. Adekunte

The design, construction and monitoring of the deep excavation support for the basement of a large-scale commercial development in Cavan, Ireland is presented. Excavation area was adjacent to existing structures and retained height H varied between 4.0m ? 11.0m. In areas where excavation depth H < 5.0m, wall was designed as cantilevered section. However in sections where 5.0m = H = 11m, additional wall supports were required for serviceability reasons. Traditionally, designers often provide additional wall support through the use of tie-back ground anchors, raking props and braces. On the current project, the main contractor was not in support of the use of temporary props so as to maximise working space, while owners of adjacent properties disapproved the use of tie-backs. The limited set-back between the wall line and site boundary also contributed to the complexity of the project. A rare alternative solution has been adopted. This novel approach involved buttressing the wall with steeply raking bored tension piles at regular intervals along the wall. Comparison of the monitored deflections in the cantilevered sections with those recorded at sections where tension piles were used shows the novel solution to be safe and quite effective. This approach is also considered to be more economical when compared with ground anchorage and propping.

Jan 1, 2008

By Dennis Nottingham

"Increased interest in seismic soil liquefaction and preventative soil stabilization sets the stage for improved deep compaction methods using pile driving techniques. In 1971, L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100-foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers’ experiments, observations and measurements, led to an “H” pile probe design which has produced measured soil density improvements up to 250% using SPT “N60” values as a measure. Case histories of two projects involving extensive SPT soil sampling comparative measurements will be discussed along with findings that led to the compaction success. Applications to numerous modern “Open Cell” bulkhead projects will be presented and discussed.INTRODUCTIONNecessity often is the basis for innovation and such was the case for needed cost-effective deep soil fill compaction in Open Cell bulkheads where granular fill below water levels was often placed.Open Cell bulkheads were developed by PND Incorporated starting in 1980, for the express purpose of meeting client demands for an economical, easily constructed, extremely strong structure. Earth-filled structures historically have had a long history of problems with stability, scour and settlement.Open Cells are flexible steel sheet pile membranes supported by soil contact with embedded tail anchor walls.This concept creates an integral reinforced soil system. The result is a structure that can withstand large settlement and support a variety of very large loads. In effect, viewed from above the structure becomes a series of U-shaped horizontal membranes that require no toe embedment for stability. The Open Cell bulkhead is constructed of only three components: flat sheet piles, fabricated connector wyes and anchor piles. Compared to alternative structures, several cost savings are realized from this land based construction such as, reduced sheet pile area, greater construction tolerance, minimal pile penetration, and simplified backfilling procedures. In seismic regions or weak soils, the tail walls can be extended as required to guarantee fill mass stability."

Jan 1, 2005

By Mostafa Mossaad, Ali Helwa, Manal Salem

Support of excavation (SOE) design practice tends to model SOE elements using two-dimensional (2D) analyses to avoid the complexity associated with three-dimensional (3D) analyses. Such practice overlooks soil arching in the horizontal plane and prevents designers from accounting for elements such as capping beams as part of the statical system. This study simulates square excavations supported by cantilever slurry walls in dry cohesionless soil using 2D and 3D finite element (FE) models. First, side support wall behavior is compared from 2D and 3D FE models for variable excavation length to depth (L/H) ratios. Second, the effect of slurry wall lateral bending stiffness on wall behavior is studied by modeling the wall using plate element with isotropic and anisotropic wall stiffness. Finally, the sensitivity of cantilever wall behavior to the presence of capping beam is illustrated. The study concludes that unbraced excavations with L/H ratios greater than 5 almost resemble plane-strain conditions. Slurry walls are better simulated in 3D FE models by dividing the plate element into discrete panels or by assigning anisotropic bending stiffness to the plate element. Finally, the presence of capping beam affects the behavior of cantilever walls resulting in reduction of deflections and redistribution of bending moments. INTRODCUTION Support of excavation (SOE) design practice ranges in complexity from conducting simple hand calculations to performing three dimensional numerical modeling depending on several factors among which is the geometry of the design problem. This paper addresses walls that are designed using numerical modeling, and discusses the factors governing the choice of the most suitable modeling approach. It has been believed for a while that modeling excavations using 2D numerical models would lead to a more conservative solution, which turned out to be incorrect in specific cases. This paper attempts to describe cases where 2D finite element modeling could be on the conservative side and other cases where it could be less conservative than the more complex 3D modeling.

Jan 1, 2018

By H. S. Radhakrishna

Foundations supporting power transmission and communications towers are subjected to both compression and uplift loads, often of a cyclic nature. Some novel foundations, combining the beneficial features of grouted and helix anchors with that of compression piles and grillages, were developed by Ontario Hydro during the construction of high voltage transmission lines in Ontario, Canada. In addition to meeting the load requirements, the foundations permit easy installation in swampy areas and also minimize impact on environmentally sensitive terrain. This paper describes the features of these composite foundations and outlines the performance criteria used for their design and installation on the basis of load test results.

Jan 1, 2010

By Srijit Bandyopadhyay, Aniruddha Sengupta, G. R. Reddy, Raj Banerjee

The objective of the present endeavor is to compare the performance of a pile raft system in foundation sand subjected to lateral loads. To study the behavior of pile raft system in sand a laboratory test was conducted on small scale model foundation system. The raft and pile was modeled by square concrete foundation of 250 mm x 250 mm x 15 mm in length, breadth and thickness and 25mm diameter and 250mm long circular pile located at the center of the raft. The system was tested under static lateral loads of 6.25N, 12.5N, 18.75N and 25 N respectively resting on dry Kasai River sand. A vertical surcharge pressure of 1.5kPa (10 kg) was applied on top of the model raft for each case. The results of the model tests have been simulated by a general purpose 3-D finite element software and the model has been validated with experimental results. The moments of the pile obtained from the model tests and those predicted by the numerical analyses for all the lateral loads matches reasonably well. For matching the trend of bending moments obtained from experiments, validation with theoretical results have been done with the help of Matlock and Reese (1960) approach for a single value of lateral loading. Moreover, a parametric study has been conducted with 5mX5mX0.3m raft size with 0.5m diameter and 5 meter long pile with increasing number of piles namely 2, 5 and 9 respectively to study the response in terms of moment and lateral deformation under available earthquake loadings, like Loma Prieta (1989) and Darfield Christchurch (2010). Bending moments of piles and load deformation curves for lateral loading have been studied for each case in which it is observed that the bending moments of pile significantly reduces (around 4 times) as the number of pile is increased to two, but it decreases to a nearly constant value (it saturates) as the number of pile is increased to five and nine. Moreover, the lateral deformation of piled raft system drastically reduces (around 2.4 times) for two pile system, and it saturates to a constant value with five and nine pile system. All these results indicate the constancy of stiffness irrespective of the number of piles in the piled raft.

Jan 1, 2015

By Emad Farouz, Francis A. Abreu

"This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule.This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.SITE AND PROJECT DESCRIPTIONThe Great Neck Water Pollution Control District (GNWPCD), located in the Town of North Hempstead in Nassau, New York, owns and operates a municipal wastewater treatment plant (WWTP) that discharges treated effluent through an outfall to Manhasset Bay, which is a tributary of the Long Island Sound. The site is located west of Manhasset Bay and is surrounded on three sides by local roads, and commercial, industrial, and recreational properties. The site has a gentle slope ranging from elevation +20 to +7 from west to east, respectively, based on the Nassau County Datum.To comply with new nitrogen discharge requirements and new design flows, the GNWPCD contracted CH2M HILL, Inc. and William F. Cosulich Associates as a Joint- Venture (JV) to design and provide services during construction of eight new advanced nitrogen removal facilities."

Jan 1, 2017

By James S. Graham

Marine design and construction methods are presented on the caisson foundations for the tower piers at the Brooklyn, Ben Franklin, Delaware Memorial 1st, Tappan Zee, Walt Whitman, Throgs Neck, Verrazano Narrows, Delaware Memorial 2nd, and Newport Bridges. All of the bridges are founded on caissons, bearing on bedrock, soil, or piling. Caissons at the Tappan Zee Bridge are partially supported by piling and partially by buoyant forces. General subsurface conditions for each are provided. The purpose of this paper is inform engineers how bridge foundations using caissons were built over major waterways in the Northeastern USA in the past, anticipating a surge of new bridge construction in the near future.

Jan 1, 2013

By Emad Farouz

This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule. This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.