Search Documents

By Ahmad Mahboubi

The damage caused by catastrophic earthquakes has always been an incentive towards more sophisticated building codes and requirements. In parallel to computer technology development, the engineers? attitude towards acquisition of more accurate results is increasing. This approach leads to designation of structural elements with more elaboration considering different aspects of their behavior. In addition, less simplified methods will be considered as satisfactory for analyzing such problems. The problem of soil-pile-structure interaction is one of the phenomena that can be included in this category. In general, there are two methods by which the study of soil-pile interaction phenomenon is studied. These include direct and sub-structuring methods. The sub-structuring approach relies on the linear or slightly non-linear behavior of soil since it employs the results of kinematic interaction analyses for inertial interaction studies. In the past, the kinematic interaction between pile-soil was considered as negligible. This was due to the softer nature of the surrounding soil that increased the time period of vibrations. However, more research revealed that although this approach was consistent in many cases, there were some sites where the time period decreased. This was due to the material properties of the foundation and the soil, in a way that caused the frequency of vibration meet natural frequency of the system. The second type of interaction is the inertial interaction which reflects the effect a structure on top exerts on the oscillation experienced by the foundation. This paper examines the impact of vertical load on the inertial interaction by virtue of impedance functions. Three different load cases for the structure at the top of a pile foundation were considered for the analyses conducted in this study. The changes in the stiffness and damping of the system by frequency are studied and finally, the results are presented.

Jan 1, 2010

By Hodjat] [Shiri

A 4-legged jacket structure was installed by an Offshore Installation Contractor (OIC) in the Persian Gulf. In addition to four open-end pipe piles, six conductors were installed by OIC. During the installation of the piles and conductors, some cemented layers were encountered, which had not been accounted for in the foundation design performed by an independent well known offshore geotechnical site investigation contractor (OGSIC). Six months later, the Drilling Company (DC) hired by Client to execute the wells, reported that all of the six conductors were presenting anomalies, such as vertical misalignments up to 10o and/or collapse of the conductors tip and mid height. The DC faced with serious problem in drilling of the wells and in spite of several times milling the conductors and spending 40 days unpredicted extra time, some of the routes could not be opened and Client lost millions of dollars due to direct and indirect associated costs and expenses. This paper presents a complete overview of all engineering, construction and specially geotechnical investigations and shows that how an inaccuracy in interpretations of the results of an offshore geotechnical site investigation as the main reason in this case study can cause serious damages to whole project with unbelievable time and cost impacts some times up to millions of dollars.

Jan 1, 2006

By Richard Deakin

This case study describes aspects of the design of bridge foundations using 320mm diameter steel tube piles in the vicinity of Montréal, Canada. In this area, these piles are a very commonly used and cost effective solution for deep foundations. Typically they are driven through thick Champlain Sea Clay to bear onto stiff, strong rock. However, in some locations there is a layer of glacial till between the base of the clay and the rock which cannot always be fully penetrated by the piles. There is currently little published information, about the bearing capacity of these piles in the local till, and this paper presents and discusses some pile-test data from a recent project. The nature of the glacial deposits in the study area is presented using information gained from published geological data, the project ground investigations and site observations. The design approach and assumptions are discussed, together with the aims and outcomes of preliminary field driving trials and pile tests. The paper then discusses the results of dynamic tests undertaken on production piles. Bearing capacity factors are back analysed from the dynamic test results and compared against values assumed within the design. Observations are made that designers of future foundations in similar conditions may find informative.

Jan 1, 2011

By Steve Davidow, Scott Tunison

As the demand for electric power grows and generation facilities are constructed in more remote areas, the industry faces an increasing number of foundation construction challenges. The importance of quality geotechnical information prior to construction is accentuated by the linear nature of the projects and the potential for drastic changes from one end to the other, but is often difficult or unfeasible to obtain. Alignments are crossing remote, rugged and/or environmentally protected terrain, and completing a comprehensive geotechnical program is made challenging from an access or economic standpoint, or both. In these situations, the industry needs a flexible foundation alternative. This paper will present micropiles as that alternative and demonstrate how the implementation of micropile foundations mitigated these challenges on the Koolau-Wailupe 46 kV Circuits in Oahu, Hawaii, which involved rugged, steep slopes and helicopter construction methods. It will detail the selection of micropiles over other foundation options, micropile and steel pile cap design methodologies, foundation construction, and quality control. Special attention will be given to the unique geology in the area, and why precise identification of saprolite and basalt layers was integral to the successful performance of the foundations. The intention is to communicate the benefits of a flexible solution based on continuous collaboration between design and construction.

By Paul J. Sabatini

Between 2008 and 2009, more than 6,000, 23-m long deep mixing method (DMM) elements were constructed to support 124 concrete mats comprising the foundations for the process trains for an LNG facility. The Owner requested first-of-its-kind analyses and assessments to confirm the quality and reliability of the DMM foundation. This paper provides information on these assessments and the procedures used to ultimately conclude that a fit-for-purpose foundation system was constructed. During early phases of construction, several DMM test cores revealed nodules of unmixed clay in upper core samples. A comprehensive review of available DMM core information was undertaken. It was concluded that the amount of coring being conducted as part of the contractor?s QA/QC program should be increased to achieve a foundation system with the required level of reliability. Three-dimensional finite element analyses were completed considering various distributions of defects in the DMM elements and the effects of potential downdrag on DMM elements. Calculated mat settlements and mat stresses were compared to cases without defects in the DMM elements. Various distributions of loaded and unloaded mat areas and number and position (both in the subsurface and laterally) of defects were considered. Four (of the 124) mats were identified as potentially ?at-risk?. The settlement performance of these mats is currently being monitored and, to date, performance has been acceptable.

By Morris J. D, Baldwin Z., Wiltcher P. M

21 Moorfields is an oversite development in central London spanning Moorgate tube station. It required the installation of both the highest loaded bearing piles and the highest top loaded static pile test ever undertaken in the UK, at 50.5MN (5,680 tons). The 17-storey building is founded on only 15 large diameter bored piles installed through the roof of the live station. The piles are located in two parallel rows 50 m (164 ft) apart, bridging the underlying train lines and the Crossrail tunnel below. This unique project required a diverse cross-section of skills and experience from the Project Team as we not only pushed the boundaries of design but also those of construction practices. Our team therefore needed to be made up of members from multiple businesses and disciplines. The team worked together, in a highly collaborative environment, for around two years before any work started on site. A key challenge for this project was that there was only one opportunity to construct each pile. If a position had to be abandoned there were no alternative locations and the impact on the project would have been catastrophic. It was therefore vital that all events that may have led to the abandonment of a pile were investigated ahead of commencement on site. Risk elimination and mitigation strategies were developed for all eventualities whether they be associated with the design or construction processes. The successful pile load test, coupled with all contract piles being fully instrumented with state-of-theart fiber optic (CemOptic) cable along their full length, has improved our understanding of the performance of such large and heavily loaded piles. The works piles will all be monitored during the construction of the new building, providing new insight into their real-world performance. Such groundbreaking work has never been undertaken before in the UK and has the potential to significantly influence the industry’s understanding of pile behavior, and design, in the future. This paper will discuss the challenges the team encountered during the design and construction of this highly complex urban project, particularly when adopting, by necessity, a pioneering approach.

By David H. Sanders, Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Large-diameter drilled shafts (DS) are a critical part of a seismic-resistant system, and therefore it is important to be able to accurately model lateral resistance. To undertake the lateral load analysis of largediameter DS, a finite-difference p-y analysis program, NVShaft, is being developed at the University of Nevada Reno. Validation of the new program involved numerous p-y analyses using commercially available programs. Subsequent comparisons suggested the program's ability to yield reasonable predictions for typical diameter DS. Based on the I-15/US 95 load test program carried out in Las Vegas, NV, this study presents the evaluation of NVShaft in Nevada’s subsurface condition. Lateral load analyses of a 2 ft and an 8 ft diameter DS were attempted using NVShaft. The location of the applied lateral loads and the presence of cemented soil-layers were incorporated in the modeling. A good agreement between NVShaft prediction and the measured response was found for the 2 ft diameter DS. For the 8 ft diameter DS, a stiffer response was predicted. The inspections of the moment-curvature characteristics at different load levels suggested cracked response of the concrete due to prior axial load testing may be one of the reasons behind the deviation.

By Narong Thasnanipan

This paper presents the outcome of the contest on the prediction of the static axial load capacity of diameter 1.20m bored pile founded at 46m below existing ground. The test pile was constructed by wet-processed method and instrumented with vibrating wire strain gauges. Different methods used by the contestants in prediction of load-settlement characteristics are described and compared with actual load test results. Load-displacement behavior of test pile is found to be better than expected. Major difference between prediction and actual test is the higher frictional resistance of Second Sand Layer achieved in the actual load test. The hyperbolic load transfer method used by one of the contestants was applied to back-analyze the load-displacement characteristics of the test pile at different conditions.

Jan 1, 2006

By Eric S. Lindquist

Two microtunnel access shafts were constructed using the Cutter Soil Mixing (CSM) method in the San Joaquin Delta region of California, east of San Francisco. Unlike conventional slurry walls and diaphragm walls that utilize concrete, soil mixing relies on blending the soils in situ with a cement slurry to create a soil-cement wall. Cutter Soil Mixing technology utilizes two sets of vertically mounted cutting wheels rotating about a horizontal axis to produce rectangular panels of treated soil. Overlapping of the soil mixed panels enabled the construction of two circular shafts. CSM panels were constructed to a depth of 29 m (95 ft) for the microtunnel jacking shaft and to a depth of 19 m (63 ft) for the microtunnel receiving shaft. The site presented several challenges, including the high depth of treatment, the variable nature of the alluvial soils, and the high water table. This paper describes the CSM technique and presents the design, construction, quality control measures and advantages of using this method for this project.

Jan 1, 2010

By Ilhan Chang, Ernest Nsabimana, Kiseok Kwak, Juhyung Lee, Young-Hoon Jung

"Numerical analyses were performed to analyze the behavior of two different type of suction piles (mono type and group type) under various soil layer conditions (uniform silty clay layer, uniform silty sand layer, and two-layer deposit consisting of clay and sand layers) and lateral loading locations (top, middle, and bottom of the suction pile). According to the results, mono suction pile shows maximum resistance when load is applied on its middle, regardless of the soil layer conditions, while group suction piles varies significantly according to the allowance on head rotation. When head rotation is allowed, the behavior of group type piles become similar to the behavior of mono suction pile. Whereas, when rotation is prevented, resistance is maximized when load is applied on the top head. Moreover, group suction piles show higher efficiency regardless of the ground condition and geological stratum. For further advances, concrete block on the top of group suction piles are suggested as an effective alternative method to prevent partial rotation and maximize ground resistance for group suction piles.IntroductionWith the development of offshore technology, applications and real site installations of suction piles are increasing significantly nowadays. They are generally used as mooring anchors in various floating structures, marine platforms, and offshore wind turbines. According to its convenience in installation and removal, suction type foundations are becoming good alternatives for deep ocean support systems. The bearing capacity is similar to the bearing behavior of ordinary offshore structures (piles or drilled shafts). The most common use of suction caissons is anchors for catenary mooring lines, where the chain angle at the mudline is close to zero (Randolph, 2002; Sharma, 2004).Recently, it is reported that a huge isolated single suction pile can be replaced by a group of moderatesized suction piles (Randolph et al. 2004). A single monopile is easy to be produced and installed in site. It is expected that monopile foundation is not applicable for deep depths because it has a limitation on penetration according to its huge side skin area (i.e. friction). Moreover, stiffness requirements sometimes render thicker pile wall conditions which are impractical to be produced."

Jan 1, 2017

By David Chadwick, Paul Marsden, Chris Hughes, Mathias Delapille

"Following damage caused by the 2011 Christchurch earthquakes, the NZ$127.5million Christchurch Town Hall Restoration project is due for completion in 2018. The building is undergoing extensive repairs and a strengthening regime to meet New Zealand’s New Building Standard. One major aspect of the project is the stabilisation of the soil directly beneath the building using interconnected jetgrouting columns installed a cellular configuration, the purpose of this being to decrease the likelihood and severity of foundation movements caused by earthquake-induced soil liquefaction and lateral spreading. The soils encountered on the site ranged from cobbles and gravels through to sandy silts with a significant quantity of timber and rootlets. This wide variation of soil types presented a number of challenges with regard to effective and consistent treatment by jet grouting. The paper presents an overview of the quality assurance practices and also the testing regime adopted on this project.INTRODUCTIONMost of the deformation experienced by the Christchurch Town Hall structure over the course of the Canterbury earthquakes was caused by movement of the underlying ground. Two primary mechanisms of ground deformation were observed:- Liquefaction of the soils underlying the building foundation- Lateral spread of surface soils towards the free face at the river edge which runs 20 metres from the building. This mechanism also resulted in additional vertical settlement of the building foundations.The overall foundation design philosophy adopted by the project team for the Christchurch Town Hall Conservation Project has been to improve the ground directly beneath the structure to mitigate against these two mechanisms of ground movement. Additionally, a robust raft slab is proposed to distribute the foundation loading more evenly and increase the ability of the structure to resist lateral stretch of the underlying ground.The ground improvement system proposed by the Client’s geotechnical consultants, Tonkin &Taylor, comprised a cellular arrangement of interlocking jet grout columns, this arrangement would effectively encapsulate the soil within the cells preventing lateral spread.In total 1,097 interlocking jet grout columns, extending over the entire floor plan of the structure, were required to satisfy the design requirements."

Jan 1, 1900

By John F. Spence

Ever since opening, the M25 motorway to the west of London has carried a rapidly increasing volume of traffic. The section of M25 between the junctions with the M3 and M4 motorways, which is in the near vicinity of Heathrow airport, is the most heavily trafficked section. Piling and ground treatment was required for motorway widening works over this route, which is 7 miles long. The foundation works were undertaken next to the live motorway and beneath the flightpath for aircraft landing and taking off at the airport. The paper describes the foundation construction techniques used, and the how the methods were affected by the live motorway and the height restrictions imposed by the airport. A unique method of piled retaining wall construction is also described.

Jan 1, 2007

By Harald Vogel, Johannes Lachenski, Friedemann Koetzel, Sebastian Schnell

In this paper, a digital subsoil approach, a work-in-progress, will be presented describing the transformation from a classical 2D to digital 3D thinking process in the design of geotechnical structures. Certain pitfalls as well as lessons learned are described, and the reader can understand that the digitalization process of the design of geotechnical structures is always a problem-focused approach by creating systems for certain processes rather than setting rules or regulations. Three project examples are presented. Two of the presented project examples feature a heterogeneous geology distribution and made it necessary for the design of the foundations to work with 3D subsoil and 3D calculation models. However, the digital 3D design process in the third project, an inner-city excavation pit, is driven by the complicated boundary conditions making it necessary to work in a parametric 3D design space. All projects have in common, that new processes had to be developed. The paper concludes with a flow chart describing the process of the elaborated digital subsoil approach.

May 1, 2022

By J. Brian Anderson

Jointed micropiles were investigated to support bridge foundations where shallow rock was present. In this application, micropiles would have some amount of unsupported length, and would be subject to nominal lateral loads. Five lateral load tests were conducted on micropiles to demonstrate the impact of casing joints and rock socket embedment on lateral behavior. Load tests were simulated with FB-Multipier, a hybrid-finite element program for analysis of deep foundations, for proper design of the loading apparatus and instrumentation. The micropile sections were 2 m (6.56 ft) long, 273 mm (10.75 in) in diameter, 13 mm (0.5 in) thick walled, with a 50-mm (2-in) long threaded joint. Micropiles were made of one to three casing sections and were embedded 0.3, 0.6, 1.5, or 3.0 m (1, 2, 5, or 10 ft) into rock. In each test, two identical micropiles were pulled together using a simple frame until the weaker pile failed. All micropiles were instrumented with inclinometer casings while two contained strain gages at 0.76 m (2.5 ft) intervals. Load and displacement were measured at the pile heads. Tests showed the embedment of 0.6 m, 1.5 m, and 3.0 m (2 ft, 5 ft and 10 ft) sufficiently carried lateral loads over 180 kN (20 tons). The piles embedded 0.3 m (1 ft) were not able to maintain lateral load. In general, all micropiles tested to failure exhibited a brittle failure mode where there is small lateral deflection followed by a sudden failure at the casing joint. This was demonstrated in three of the load tests. In most cases, the micropiles were stiffer and stronger in the load tests than originally predicted numerically. The final test, where piles were not loaded to failure, verified that embedding vibrating wire rebar strain meters in the grout captured the bending moment profile of the micropile. The results showed the maximum moment in this case being carried directly across the threaded joint as predicted by the preliminary models. The results of these tests were used to calibrate the FB-Multipier numerical model. Using a load test that included bending strain measurements for a match, the soil properties were adjusted to produce reasonable matches for all of the load tests.

Jan 1, 2011

By Seffen Leppla, Rolf Katzenbach, Matthias Seip

"Abstract The economic and safe design of deep foundation systems in difficult soil conditions is based on a reduction of construction material used, construction time spent, energy consumed and a high-level modelling of the soil-structure-interaction. The special foundation system Combined Pile- Raft Foundation (CPRF), in-situ load tests on the construction site and a sufficient soil investigation allow cost optimised constructions. In any case at challenging projects the observational method has to be applied for verification and quality control of the design. Regarding the 4-Eye-Principle as basis of the quality control management an independent peer review of the planning, design and construction phases is the guarantee for safety, serviceability and optimisation of all projects. Main execution standards for the construction of deep foundations based on the Eurocode 7 are summarised and discussed. The paper presents the basics of the safe and qualified design and construction of foundation systems including quality assurance. The application in engineering practice is shown on achallenging project of high-rise buildings with difficult boundary conditions.IntroductionThe construction of deep foundation elements in inner cities are special challenges due to the limited space for the construction works and the effects on existing buildings (Figure 1).An economic and safe design of deep foundation systems in difficult soil conditions is based on the following main aspects:•,qualified experts for planning, design and construction•,interaction between architects, structural engineers and geotechnical engineers•,adequate soil investigation•,design of deep foundation systems using the Finite-Element-Method (FEM) in combination with•,enhanced in-situ load tests for calibrating the soil parameters used in the numerical simulations•,quality assurance by an independent peer review process (4-eye-principle) combined with theobservational method if necessary"

Jan 1, 2014

By Challa Venkata Rami Reddy, Anindya Roy, G. R. Konni

This paper presents the results of pile lateral capacities obtained from both conventional design and fullscale pile lateral load tests. Conventional design using P-Y curve analysis is very commonly being used by designers; designers use well accepted software programs like Lpile and Allpile for analysis. However, these programs do not cover the soil models to simulate engineering behavior of marine carbonate sands; which generally have different engineering behavior than silica/quarts sands. In this study, the existing soil models for common sands have been used to assess pile lateral capacities and these results are compared with the results from full-scale instrumented pile lateral load tests performed in compacted marine carbonate sand fills of artificial island constructed for oil and gas facilities in Abu Dhabi. The objective of this study was to verify the applicability of the existing sand soil models for carbonate sands and also to verify the associated conservatism in the pile lateral capacities. This study shows that the actual pile lateral response is much stiffer than what was anticipated through the LPile analysis. Therefore, further research focus may be required to capture the engineering behavior of the marine carbonate sands to develop specific P-Y curves.

Sep 8, 2021

By Josef K. Alter

Crosshole Sonic Logging (CSL) of drilled shafts requires 1.5-in (38-mm) or 2-in (51-mm) I.D. sonic access tubes to be installed inside the steel reinforcement cage. The sonic access tubes do not contribute to the structural capacity of the drilled shaft. The proposed use of Ischebeck TITAN T73/56 CSL/Hollow Threaded Rebar for Cross Hole Sonic Logging Access Tubes Combined with Longitudinal Concrete Reinforcing in Drilled Shafts (patent pending) is discussed as an alternative method of construction and CSL probe access. The T73/56 hollow threaded rebar/sonic access tube performs as a high strength rebar while at the same time creating a 2.2-in (56-mm) I.D. sonic access tube. The deformed high strength hollow bar provides better adhesion to concrete thus reducing the problem of debonding associated with smooth PVC and steel pipe. A cost comparison using conventional rebar with added sonic access tubes is discussed. The use of T73/56 CSL/Hollow Threaded Rebar as a value engineering alternative can reduce both material and labor costs for drilled shaft construction and can provide an advantage where anchor bolt cages and longitudinal reinforcing create congestion.

Jan 1, 2011

By John C. Niedzielski, A. Frances Ackerman

The existing US-70 Bridge over the Gila River at Bylas, Arizona is planned to be replaced due to its current poor condition. The replacement bridge is planned to be a 15-span, 1,904-foot (580 meter) long bridge, the third-longest bridge in the state highway system. Within the Gila River floodplain, granular alluvial soil is underlain by cohesive lacustrine soil; bedrock was expected due to nearby terrain but not encountered within the geotechnical exploration depth of 166.5 feet (51 meters) or less. Based on the anticipated loading conditions, design scour depths and the soil conditions, the full structural loads are carried by large diameter drilled shafts; therefore accurately determining the axial capacity of the proposed drilled shafts has important practical and safety implications. The conventional methods for axial capacity determination may be overly conservative to use for design in the site’s layered granular and hard clay soils. An Osterberg cell load test was performed to obtain detailed information on the load transfer from the drilled shaft in side friction and base resistance to allow optimization of the bridge foundation design. The fullscale field test played a significant role in the design of the project’s deep foundations, notably, by incorporating the specific subsoil properties and consequently, an exact prediction of the load-settlement behavior under loading. This paper provides the results of the geotechnical site investigations, drilled shaft load testing procedures, and shaft load distribution from the load test results. Comparisons were developed between predicted axial capacities of drilled shafts using several design methodologies and the axial capacity measured from static load testing. The load test results showed that underestimation of the axial capacity is evident using conventional methodologies. The exact prediction of the load-settlement behavior under loading combined with a site-specific design approach, resulted in a substantial reduction of foundation costs due to reduced drilled shaft dimensions.

Jan 1, 2017

By Robert B. Bittner

The new gated dam on the Monongahela River at Braddock, Pennsylvania, was built for the US Army Corps of Engineers using an innovative "In-the-Wef' technology. A key feature of this technology involves construction of the foundations through the water and later mating the completed structure or a shell of the structure to the pre-installed foundation. This paper presents a description of the structure, its foundation, construction sequence and design details required to successfully Implement this technology.

May 11, 2007

By Scott M. Doehla

A proposed rehabilitation of a 200,000 sf, 75-foot high steel-frame building at the former U.S. Navy Yard in Brooklyn, New York required the review of existing foundation data and an investigation of the foundations with respect to their condition. The building was constructed in stages between 1856 and 1933, including several expansions and interior equipment with isolated foundations. The building has clear spans on the order of 50 feet and at one time supported cranes allowing transport of heavy equipment through the building. The proposed rehabilitation is to include a food manufacturing center and office space having multiple stories. Original construction drawings, available from the Brooklyn Navy Yard Development Corporation?s drawing archive, were reviewed to determine the foundation system supporting the structure. The original drawings provide a window into the methods utilized during late 19th and early 20th century pile foundation construction. The review revealed that the building is supported by pile foundations ranging from timber to concrete-filled steel pipe (depending on the year of construction). Annotations including pile driving records were available on some drawings indicating the design and as-built capacity (using the ENR formula for driving resistance). An investigation consisting of test borings was performed to identify the subsurface conditions underlying the building for evaluating theoretical capacity of the piles. A test pit investigation was performed against existing columns within the structure to expose the piles and pile caps for inspection pertaining to pile condition. The test pit investigation revealed methods utilized during original construction to integrate new columns with existing floor slabs, the use of below-grade brick arches to support a floor slab, and the condition of timber piles which were likely installed up to 120 years ago. The observations made within the test pits were compared with original drawings to evaluate the accuracy of these drawings.

Jan 1, 2008